Radio Terminal TK20 User manual

TK20 USER GUIDE
1. TK20 Features
Maximum 1600 days working time
Police & Detector’s Best Choice
20000mAh Lithium-Polymer battery
Drop-trigger alarm build-in
GSM+GPS positioning with Google map tracking
Water-Proof design with strong magnets built-in
Remote Bug Monitoring function with DSP within five
meters of effective
Hardware Specifications:
Size: 153*58*45 (mm), Weight: 569g
GPRS:MTK 6260D
Quad band; GSM 850/900/1800/1900 MHz
Antennae: Internal, GPRS Class 12
Power: Rechargeable, 20000mAh, Lithium-Polymer
Battery
Built-in Vibration/motion sensing
GPS: U-BLOX G7020-ST, 50 channel
Antennae: Internal
Position Accuracy: <5m
Sensitivity: Tracking: (R)C161 dB, Cold starts: (R)C148
dB, Hot starts: (R)C156 dB
Cold start:<27s, Warm Start: <5s, Hot Start: 1s
A-GPS: AssistNow Online and AssistNow Offline
services
2. Product Image
Радиотерминал 121059, Москва, 1-й Можайский тупик, д. 8а, стр. 1, этаж 2 тел. : [phone] [phone] www.radioterminal.ru [email protected]

3. Installation Manual
3.1 SIM Card Pre-installation, specification note
a. GSM Sim Only
b. SIM card should have its GPRS function enabled.
c. SMS request will function only if Caller ID function is enabled.
d. If SIM card is locked via PIN, please unlock SIM.
3.2 SIM Card Installations and Removal
b. Open waterproof rubber
c. Insert SIM card into the SIM slot, metal face up, clipped corner to the right.
d. Green light is flashing for couple seconds and turn to on always on
e. Call the device SIM number and it is supposed to get through without
answer.
f. Ensure the waterproof rubber is closed after SIM installation
3.3 Device Installations
a. Avoid all metal environment to make sure device is able to receive GSM
and GPS signal.
b. Avoid high temperature environment like above the car engine
4. Button Operation
For the first time activating the device, once Sim is
inserted, device will be on automatically. No any
button operation is needed.
4.1 Button Operation for GPS function
NOTE: “button”presses must be less than 2 seconds each in all uses
This control button is at the bottom of the device
a. On: Press control button 5 times. The green indicating light will be on for
30 seconds. (System default as ON)
b. Off: Press control button 10 times. The blue indicating light will flash for 5
times
c. Reset: Press control button 15 times to reset all settings. The blue
indicating light will flash for 3 times. Insert Sim again and system will be on.
4.2 Drop Alert
System has equipped with a Drop Alert button. When device is mounted on
metal surface over 1 minute, drop alert will be triggered. Master number will
receive SMS alert when device is removed.
Радиотерминал 121059, Москва, 1-й Можайский тупик, д. 8а, стр. 1, этаж 2 тел. : [phone] [phone] www.radioterminal.ru [email protected]

5. Operation Commands Guide
5.1 Set APN: (VERY IMPORTANT AND MUST BE DONE 1ST) For the
device to send data to the server, this command MUST be enabled.
SMS: *apn*AXXX*BXXX*CXXX* This command sets the telecom Access
Point Name. BXXX refers to user name, CXXX refers to password.
If there is no user name and password required, send as *apn*AXXX*
If there is user name but no password required, send as
*apn*AXXX* BXXX*
APN information can be checked on local telecom website.
You will receive the following text: "Notice: APN is set to XXX. User name: XX.
Password: XX”
5.2 Registering the “Master”Controller
SMS to the device: *master*123456*+1XXXXXXXXXXXX*, (For
instance, master controller phone number is +1XXXXXXXXXXXX. +1 refers to
the country code. XXXXXXXXXXXX is the cellphone number. Please make sure
country code is included, and digit 0 is not needed before cell phone number)
Device Response: "Notice: Cell Phone # xxxxxxxxxx is set to master
controller, the password is 123456.”(The device has a default password of
“123456”to initially program in your PDA/Phone.
NOTE: The device will ONLY listen and respond to instructions from this
number unless you choose to turn on the multi controller function and open
the device to any cell phone number.
5.3 Changing the Password:
SMS: *password*654321* (654321 refers to new password)
You will receive the following text: "Notice: The password change is
successful for +1XXXXXXXXXX. The new password is 654321.”
Note: Changing password command has to be sent from master controller
number.
Радиотерминал 121059, Москва, 1-й Можайский тупик, д. 8а, стр. 1, этаж 2 тел. : [phone] [phone] www.radioterminal.ru [email protected]

6. Motion Detected Alert
The Master Controller will receive an alert (call or SMS) once the device
detects vibration indicating possible motion.
6.1 Vibration sensitivity:
The device you have purchased is equipped with a sensitive Vibration
detection system. The motion sensor sensitivity rate can be set by SMS
command.
SMS: *sensitive*1-5* (where X = 1-5, 1 being the most sensitive, 5 the
least, default setting is 1)
1=3 seconds continued vibrating
2= 6 seconds continued vibrating
3= 9 seconds continued vibrating
4=12 seconds continued vibrating
5=15 seconds continued vibrating
Device Response: “Notice: Vibration sensitivity is set to 1-5.”
6.2 SMS or CALL Alert Settings:
With the vibration detection system. There will be a Call alert (call master
number 2 times) or a SMS alert generated and send to master number, when
any motion is detected after 3 minutes of non-movement. The system
default setting is call alert, and can be turned off by SMS command
SMS: *alertoff*
Device Response: “Notice: System has ended alert function.”
SMS: *smsalert*
Device Response: “Notice: System has entered SMS alert function.”
SMS: *callalert*
Device Response: “Notice: System has entered call alert function.”
6.3 Period Motion Alert
System will enable motion alert function at appointed periods, up to 3 time
periods. Time format need to be in military time and can be set to hour. e.g.
0811，1418 refers to 8:00-11:00,14:00-18:00 of the day.
SMS：*continuousalert*0-23*0-23*
Device Response: “Notice: System has enabled period alert function at
appointed time period.”
SMS：*continuousalertoff*
Device Response: “Notice: System has ended period alert function.”
Радиотерминал 121059, Москва, 1-й Можайский тупик, д. 8а, стр. 1, этаж 2 тел. : [phone] [phone] www.radioterminal.ru [email protected]

7. SMS Location Query
The GPS module establishes location and creates an event, which is sent
immediately. The data packet returned via SMS includes battery level and any
applicable alert mode. User can track the device location via SMS whenever,
wherever.
7.1 SMS: *locate*
This command “Pings”the unit from the master controller for a spot location
report delivered via SMS back to the Master Controller.
Device Response: You will receive back a text include latest information of
latitude, longitude, date, time and ranking. And you can find this location in
details from the tracking website.
7.2 SMS: *locateaddress*
Device Response: You will receive back a text include rough address
information of the device. Tracking website is not required.
7.3 SMS: *locatemap*
You will receive back a text message with a google map link, click the link in
order to view the location through cellphone browser. It is suitable for smart
phone user only.
8. Remote Listening
The device is equipped with an audio DSP which enable master controller to
monitor the environmental sound via calls. Master controller can enable the
bugging function either by calling the device or command the device to call
back.
8.1 SMS: *callin*
Enables the Master controller to call the device to start listening within
30mins after the SMS is sent.
8.2 SMS: *callback*
The device will call the master controller enabling the Maser Controller to
listen when the call is accepted.
9. Website Tracking
Tracking Website: www.miitown.com
Account Login ID: Registered Master phone number. It's the same number as
5.2.
Радиотерминал 121059, Москва, 1-й Можайский тупик, д. 8а, стр. 1, этаж 2 тел. : [phone] [phone] www.radioterminal.ru [email protected]

Account Login Password: Default as 123456.
It can be changed on the tracking website.
Recommended Web browser are Chrome, Firefox or cellphone default
browser.
9.1 Real-time Tracking
This function delivers a highly granular tracking record of a specific route.
Once motion is detected, every 10 seconds locate records are uploaded every
1 minute to the server during motion.
This function is suitable for speed moving object tracking. And it works in
motion only.
9.1 By SMS
SMS: *routetrack*1-99* (1-98 represents hours of accumulated data, 99
means always on)
Device Response: “Notice: System has entered routetrack function for *XX*
hours.”If you sent 99 the device responds: “Notice: Routetrack function is set
to always on.”
9.1.1 Real-time tracking location data collecting interval.
The smaller interval, the higher accuracy, but the higher power consumption.
SMS *rsampling*1-999* (1-999 represents seconds of data collecting
interval, default as 10 seconds)
9.1.2 Real-time tracking location data upload interval. The smaller
interval, the higher accuracy, but the higher power consumption.
SMS *rupload*60-999* (60-999 represents seconds of data uploading
interval, default as 60 seconds, minimum rate should not be less than 60)
SMS *routetrackoff*
Device Response: “Notice: System has ended routetrack function.”
9.2 Check Location
This check function enables device to collect location data regularly and
uploaded to server in appointed interval.This command can be used both in
idle and in motion, and able to work with route track function at the same
time.
Радиотерминал 121059, Москва, 1-й Можайский тупик, д. 8а, стр. 1, этаж 2 тел. : [phone] [phone] www.radioterminal.ru [email protected]

Check by hour
SMS: *check*0-99*(0-99 represents hours of data upload interval, default
as *check*0*)
Check by minute
SMS: *checkm*10-999*(5-999 represents minutes of data upload
interval, )
SMS：*checkoff*
Device Response: “Notice: System has ended check function.”
Noted:
1. Check function is able to work with routetrack command at the same time.
2. System is default as *check*72*. One location will be uploaded to server
every 72 hours.
3. Location will be uploaded to server no matter device is in motion or not
9.3 Appointed Time Tracking
Appointed Time Map Location. Check map location at appointed time, up to 3
time points. Time format need to be in military time and can be set to every
half hour. e.g. 0830, 1400,1830 refers to 8:30, 14:00,18:30 of the day.
SMS：*timinglocatemap*XXXX*XXXX*XXXX*
Device Response: You will receive back a text message with a google map
link, click the link in order to view the location through cellphone browser. It is
suitable for smart phone user only.
SMS：*timinglocateoff*
Device Response: “Notice: System has ended timing locate function.”
9.4 Period Tracking
Period Tracking. GPS Location data will be uploaded to server during the
appointed periods, up to 3 time periods. Time format need to be in military
time and can be set to every half hour. e.g. 08001100，14001830 refers to
8:30-11:00,14:00-18:30 of the day.
SMS：*periodlocate*XXXXXXXX* XXXXXXXX*
Device Response: “Notice: System has enabled period locate function at
appointed time period.”
SMS：*periodlocateoff*
Device Response: “Notice: System has ended period locate function.”
Радиотерминал 121059, Москва, 1-й Можайский тупик, д. 8а, стр. 1, этаж 2 тел. : [phone] [phone] www.radioterminal.ru [email protected]

9.5 Track Off
Track off will end all the tracking functions except check function.
SMS：*trackoff*
Device Response: “Notice: System has ended all tracking functions.”
9.6 Upload Alert
The upload alert function enables device upload alert status to the server
including motion alert, low battery alert and wire cut alert, Drop alert
etc. User can track alert status on the tracking website.
This function is default as on.
SMS：*uploadalert*on*
Device Response: “Notice: System has enabled upload alert function.”
SMS：*uploadalert*off*
Device Response: “Notice: System has disabled upload alert function.”
9.7 Online Control
The online command function enables device to connect with server for 15
minutes, and user will be able to send online command from the tracking
website.
SMS：*onlineon*
Device Response: “Notice: System has enabled online control function.
Data will be uploaded every 30 seconds for 15 minutes.”
SMS：*onlineoff*
Device Response: “Notice: System has disabled online control function.”
10. Deep Sleep
The Deep Sleep function enables the device to be available for long working
periods as needed, tracking remotely when either the timer wakes the unit or
motion is detected.
10.1 Sleep
Device will enter deep sleep in appointed time interval and will be
awake for 12 minute to upload 1 GPS location. If no new command，
call or new motion is received during the 12 minutes, device will enter
sleep function again.
SMS: *sleep*1-99* (1-99 represents hours of deep sleep period. )
Device Response: “Notice: System is going to enter deep sleep function,
data will be uploaded every XXX hours.”
Радиотерминал 121059, Москва, 1-й Можайский тупик, д. 8а, стр. 1, этаж 2 тел. : [phone] [phone] www.radioterminal.ru [email protected]

10.2 Motion Sleep
Device will enter deep sleep and will be awaked by motion, meanwhile upload
the current location, and will wait for 12 minutes for further command. If no
new command，call or new motion is received during the 12 minutes, device
will enter sleep function again. And the circle repeats.
10.2.1 SMS: *sleepv*
Device Response: “Notice: System has enabled deep sleep with motion call
alert function.”
10.3 Period Motion Sleep
Device will enter deep sleep for appointed time period and will be
awaked by motion, meanwhile upload the current location, and will
wait for 12 minutes for further command. If no new command，call or
new motion is received during the 12 minutes, device will enter sleep
function again, until appointed period ends. Please input time period.
SMS: *sleepv*1-99* (1-99 represents hours of deep sleep period, system will
be activated with motion during this period. )
Device Response: “Notice: System has enabled deep sleep with motion call
alert function for XXX hours.”
10.4 Sleep Off
SMS: * sleepoff*
Device Response: “Notice: System has ended all sleep functions.”
11. Status query
SMS: *status*
System Health and status check. Returns text message indicating various
system diagnostics
12. Multi Controller
This allows any SMS enabled cell device to query the unit for location,
status, etc.
121. 1 SMS: *multiquery*
“Notice: Multi query feature enabled.”
121. 2 SMS: *multiqueryoff*
The unit will now only respond to the Master controller.
Device Response: to the Master Controller: “Notice: Multi query feature
disabled.”
Радиотерминал 121059, Москва, 1-й Можайский тупик, д. 8а, стр. 1, этаж 2 тел. : [phone] [phone] www.radioterminal.ru [email protected]

13. Device Information
SMS: *about*
You will receive a text message include software edition information and
device’s serial number.
14. Timezone
The timezone need to be set before using the period motion alert,
appointed time tracking or period tracking function.
System is UTC time format and time zone need to be set by SMS.
SMS: *timezone*0-24*(0-24 represents different timezone, default as 8) eg
Italy= *timezone*2* UK= *timezone*0* Australia Perth = *timezone*8*
15. SOS Alert
The Master controller number is the default number to receive the
SOS message, other mobile phone numbers can be bounded
together to receive the SOS message by below operation 15.1
15.1 Registering the panic button bounded number
SMS to the device:
*master*123456*+1XXXXXXXXXXXX*+AXXXXXXXXXXXX*+BXXXX
XXXXXXXX*+CXXXXXXXXXXXX*,
+1XXXXXXXXXXXX refers to master controller number. +1 refers to the
country code. +AXXXXXXXXXXXX, +BXXXXXXXXXXXX, +CXXXXXXXXXXXX
refer to panic button bounded number. Up to 3 phone numbers can be
bounded
NOTE: Please make sure country code is included, and digit 0 is not needed
before cell phone number
Device Response: "Notice: Cell Phone # xxxxxxxxxx is set to master
controller, the password is 123456.”(The device has a default password of
“123456”to initially program in your PDA/Phone.
NOTE: All bounded number will receive the above response when command is
received.
15.2 Panic Button
1. Short press button 2 times and then long press button 1 time more than 3
seconds, system will send 2 SOS SMS to bounded phone numbers.
Bounded phone numbers will receive SMS “SOS! HELP! SOS!! HELP!! SOS!!!
HELP!!!”
Радиотерминал 121059, Москва, 1-й Можайский тупик, д. 8а, стр. 1, этаж 2 тел. : [phone] [phone] www.radioterminal.ru [email protected]

SMS: *soson*
Device Response: “Notice:SOS alert function enabled.”
SMS: *sosoff*
Device Response: “Notice:SOS alert function disabled.”
NOTE: The default setting is OFF. Please send SMS *soson* to enable this
function. And all bounded numbers are capable to control device as master
controller does.
16. Low battery Alert:
The device is equipped with an automatic “Low Battery”detection and alert
when the battery drops to 20% of it’s capacity. An alert SMS will be sent to
appointed phone number and the real-time tracking function will be turned off
for power saving.
Appointed alert number settings
Default alert phone number is registered master number, and it can be
changed as needed.
SMS: *lowbat* +1XXXXXXXXXXXX*, (For instance, master controller
phone number is +1XXXXXXXXXXXX. +1 refers to the country code.
XXXXXXXXXXXX is the cellphone number. Please make sure country code is
included, and digit 0 is not needed before cell phone number)
Command Setting List
Function
Command
Description
APN Setting
*apn*AXXX*BXXX*CXXX*
This command sets the
telecom Access Point
Name. BXXX refers to
user name, CXXX refers
to password.
Master Setting
*master*123456*+1XXXXX
XXXXXXX*
+1 refers to the country
code. XXXXXXXXXXXX is
the cellphone number.
Please make sure country
code is included, and 0 is
not needed before cell
phone number
Радиотерминал 121059, Москва, 1-й Можайский тупик, д. 8а, стр. 1, этаж 2 тел. : [phone] [phone] www.radioterminal.ru [email protected]

Function
Command
Description
Password Changing
*password*654321*
Original password is
default as 123456.
654321 refers to new
password.
Vibration Sensitivity
Setting
*sensitive*1-5*
1 being the most
sensitive, 5 the least.
Default setting is 1.
Motion Alert
*callalert*
Call alert will call master
number 2 times when
motion is detected after 3
minutes non-movement.
*smsalert*
SMS notification will sent
to master number when
motion is detected after 2
minutes non-movement.
*alertoff*
End Call/SMS alert
Period
Motion
Alert On
*continuous
alert*0-23*0-
23*
Device will enable motion
alert function at
appointed period of time
*continuousalertoff*
End Period Motion Alert
LLC Query
*locate*
Latest information of
latitude, longitude, date,
time and ranking.
Address Query
*locateaddress*
Address information of
current location.
Google Map Search
*locatemap*
Google Map link with
current location.
Audio Monitoring
Call in
*callin*
Call the device to start
listening within 30mins
after the SMS is sent.
Радиотерминал 121059, Москва, 1-й Можайский тупик, д. 8а, стр. 1, этаж 2 тел. : [phone] [phone] www.radioterminal.ru [email protected]

Function
Command
Description
Audio Monitoring
Call back
*callback*
The device will call the
master phone number
and enabling the Maser
Controller to listen when
the call is accepted.
Real-time Tracking
*routetrack*1-99*
1-98 represents hours of
accumulated data, 99
means always on.
Sampling Interval
*rsampling*1-999*
1-999 represents
seconds of data
collecting interval, default
as 10 seconds.
Upload Interval
*rupload*60-999*
60-999 represents
seconds of data
uploading interval,
default as 60 seconds,
minimum rate should not
be less than 60.
Real-time Tracking
Off
*routetrackoff*
End routetrack function.
Check Location
*check*0-99*
Track by hour. 0-99
represents hours of data
upload interval, default
as *check*0*
*checkm*10-99*
Track by minute. 5-99
represents minutes of
data upload interval
*checkoff* / *check*0*
End check function
Period Tracking
*periodlocate*XXXXXXXX*
XXXXXXXX*
GPS location data will be
uploaded to server at
appointed periods, up to
3 time periods.
*periodlocateoff*
End period tracking
function.
Радиотерминал 121059, Москва, 1-й Можайский тупик, д. 8а, стр. 1, этаж 2 тел. : [phone] [phone] www.radioterminal.ru [email protected]

Function
Command
Description
Appointed Time
Tracking
*timinglocatemap*XXXX*X
XXX*XXXX*
Check map location at
appointed time
*timinglocateoff*
End appointed time
tracking function
Track Off
*trackoff*
End all the tracking
functions expect check
function.
Upload Alert
*uploadalert*on*
All alerts will be uploaded
to server
*uploadalert*off*
End upload alert function
Online Control
*onlineon*
Enable online control
function
*onlineoff*
End online control
function
Deep Sleep Setting
*sleep*1-99*
1-99 represents hours of
deep sleep period.
Period Motion Sleep
* sleepv*1-99*
Period Motion Sleep. 1-
99 represents hours of
deep sleep period.
Motion Sleep
* sleepv*
Motion Sleep function
with motion alert.
Sleep Off
*sleepoff*
End Deep Sleep function.
Status query
*status*
Check system status
Multi Controller
*multiquery*
Enable multi controller
function
Радиотерминал 121059, Москва, 1-й Можайский тупик, д. 8а, стр. 1, этаж 2 тел. : [phone] [phone] www.radioterminal.ru [email protected]

Function
Command
Description
*multiqueryoff*
End multi controller
function
SOS Alert
*soson*
Enable SOS alert
function
*sosoff*
Disable SOS alert
function
Device Information
*about*
Software edition
information and device’s
serial number.
Радиотерминал 121059, Москва, 1-й Можайский тупик, д. 8а, стр. 1, этаж 2 тел. : [phone] [phone] www.radioterminal.ru [email protected]