Ransomes HIGHWAY 2130 User manual

HIGHWAY2130
RJ 100 / 052003
AVERTISSEMENT : Risque de blessures graves en cas
d’utilisation incorrecte de la machine. Les opérateurs et le
personnel d’entretien doivent être formés et conscients des
dangers encourus. Ils doivent lire avec attention le manuel
avant d’essayer de monter, d’utiliser, de régler ou maintenir la
machine.
24285G-FR (rev.6)
Series: WJ - Engine type: KUBOTAV1305
2WD Product codes: LGEA070
Series: CS - Engine type: FORD VSG413
2WD Product codes: LGEA200
Series: CU - Engine type: KUBOTAV1305
4WD Product codes: LGEA100
Series: DK - Engine type: FORD VSG413
4WD Product codes: LGEA400
WARNING:Ifincorrectlyusedthismachinecancausesevere
injury. Those who use and maintain this machine should be
trained in its proper use, warned of its dangers and should
read the entire manual before attempting to set up, operate,
adjust or service the machine.
Parts and Maintenance Manual
Nomenclature Des Pieces De Rechange
& Manuel De Maintenance

©2003, Ransomes Jacobsen Limited. All Rights Reserved

GB-1
GB
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
1 CONTENTS
2 INTRODUCTION
2.1 PRODUCTIDENTIFICATION..........................................................................................2
2.2 SPARESSTOCKINGGUIDE ..........................................................................................2
2.3 HOWTOUSETHEPARTSMANUAL ............................................................................3
3 SAFETYINSTRUCTIONS
3.1 OPERATINGINSTRUCTIONS........................................................................................4
3.2 SAFETYSIGNS .............................................................................................................4
3.3 STARTINGTHEENGINE ................................................................................................ 4
3.4 DRIVINGTHEMACHINE ................................................................................................ 4
3.5 TRANSPORTING .......................................................................................................... 4
3.6 LEAVINGTHE DRIVINGPOSITION ...............................................................................4
3.7 SLOPES .......................................................................................................................5
3.8 BLOCKEDCUTTINGCYLINDERS .................................................................................5
3.9 ADJUSTMENTS,LUBRICATIONANDMAINTENANCE .................................................5
4 SPECIFICATION
4.1 ENGINESPECIFICATION ...............................................................................................8
4.2 MACHINESPECIFICATION ........................................................................................... 8
4.3 DIMENSIONS ................................................................................................................8
4.4 VIBRATIONLEVEL .......................................................................................................9
4.5 SLOPES .......................................................................................................................9
4.6 RECOMMENDEDLUBRICANTS....................................................................................9
4.7 CUTTINGPERFORMANCE ............................................................................................9
4.8 CUTTINGPERFORMANCE(AREA) ...............................................................................9
5 LUBRICATION&MAINTENANCE
5.1 LUBRICATIONANDMAINTENANCECHART- DIESEL ................................................ 10
5.2 LUBRICATIONANDMAINTENANCE CHART-LPG...................................................... 11
5.3 ENGINE-DIESEL: FIRST50ANDEVERY200 WORKING HOURS. ............................. 12
5.3.1 ENGINE- LPG: EVERY 200 WORKINGHOURS. .........................................................12
5.4 MACHINE: LUBRICATIONWEEKLYOREVERY40 WORKING HOURS. ..................... 13
5.5 MACHINE:LUBRICATIONEVERY 400WORKINGHOURS .......................................... 14
5.6 MACHINE:LUBRICATIONEVERY 800WORKINGHOURS .......................................... 14
5.7 HYDRAULICTESTPOINTS. .........................................................................................14
5.8 ENGINEMAINTENANCE- DIESELEVERY100 HOURS ............................................... 15
5.9 ENGINEMAINTENANCE- DIESELEVERY400 HOURS ............................................... 16
5.9.1 ENGINEMAINTENANCE-LPGEVERY400HOURS .....................................................16
5.10 ENGINEMAINTENANCE-DIESELEVERY400HOURS ...............................................17
5.11 MACHINEMAINTENANCE ........................................................................................... 17
5.12 ENDOFSEASONORWHENREQUIRED .....................................................................18
5.12.1 ENDOFSEASONORWHENREQUIREDLPGENGINE ................................................19
6 ADJUSTMENT
6.1 SPEEDLIMITER. ..........................................................................................................20
6.2 ALTERNATOR/WATERPUMP-DIESEL ....................................................................... 20
ALTERNATOR/WATERPUMP/FAN-LPG ..................................................................... 20
6.3 COOLINGFANBELT-DIESEL ..................................................................................... 20
6.4 BACKLAPPING ............................................................................................................21
7 TROUBLESHOOTING
7.1 TROUBLESHOOTING-DIESEL ...................................................................................22
7.1 TROUBLESHOOTING-LPG ........................................................................................23
7.2 LPGFAULTFINDINGCHART ........................................................................................ 26
8 SCHEMATICS
8.1 HYDRAULICCIRCUIT ................................................................................................... 28
8.2 ELECTRICALCIRCUITENGINEANDSAFETYDIESEL ................................................. 30
8.3 ELECTRICALCIRCUITMAINLPG ................................................................................ 32
8.4 ELECTRICALCIRCUITENGINELPG-1 ......................................................................... 34
8.5 ELECTRICALCIRCUITGOVERNORLPG ..................................................................... 35
8.6 ELECTRICAL CIRCUITENGINELPG-2 .......................................................................... 35
8.7 ELECTRICALCIRCUITINSTRUMENTS &CONTROLS ................................................36
8.8 ELECTRICALCIRCUIT FUSESAND RELAYS -DIESEL ................................................38
8.9 ELECTRICALCIRCUIT FUSESANDRELAYS- LPG ..................................................... 40

GB-2
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
GB
2 INTRODUCTION
2.2 Spares Stocking Guide
Tokeepyour equipment fullyoperationaland productive,Ransomessuggestsyou maintainastock of themore
commonlyusedmaintenance items. We haveincludedpart numbers fortheadditional supportmaterialsand
trainingaids.
2.1 PRODUCTIDENTIFICATION
straPecivreS
oNtraPnoitpircseD.oNtraPnoitpircseD
060691800-retliFliOenignEleseiD11034-15331leseiD-retliFleuFenilnI
3250701GP
L-retliFliOenignE870871leseiD-retliFleuFenignE
026980800retliFciluardyH5280211GPL-gulPkrapS
10-7418912tnemelE
renaelCriA834302NGPL-tleBnaF
0191792800hctiwSnoitingI
A MachineName
B SerialNumber
C YearofManufacture
D MachineWeight
E EnginePower
lairetaMtroppuSecivreS
oNtraPnoitpircseD.oNtraPnoitpircseD
09620-89879 -leseiD-launaMstraPenignE atobuK G58242 straPdnaecnanetniaM03
12yawhgiH launaM
3-6198-22661 -leseiD-launaMsrotarepOenignE atobuK G78242 srotarepOdnaytefaS0312yawhgiH laun
aM
34610-79879 -leseiD-launaMecivreSenignE atobuK G07832 &ytefaS052angaM&002tropS launamstraP/noitarepO
562-
491droF-launaMstraPenignEE40542 straPgnivoMtsaFsemosnaR eugolataC
12285LSD -GPL-launaMsrotarepOenignE droF
G4
6542 droF-launaMecivreSenignE

GB-3
GB
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
2 INTRODUCTION
2.3 HOWTO USETHEPARTSMANUAL
ITEMNUMBER
Each part which is identified in the illustrations has an item number. Parts which do not have an item number may not
be readily identified in the illustration but are usually closely associated with the immediately adjacent part.
ASSEMBLIES
A complete assembly, e.g. a wheel motor or hydraulic motor or roll assembly, is listed as a complete item with
subsequent individual components listed separately.
The assembly is listed under it's part number with component parts being listed offset to the right, e.g:-
ITEM RANSOMES DESCRIPTION QTY REMARKS
PART NO.
1 LMSD798 Roll Assy. 1 ALL MACHINES
2 MBB4490 • Tube 1
3 LMSD926 • End Cap Assy. 2
4 MBB6851 • • End Cap 1
5 H009116 • • Bearing 1
6 MBB2356 • Seal Housing 1
7 A224016 • Seal 2
* A122192 Screw 2
It may not be possible to illustrate every item. With certain items purchased from outside suppliers some component
parts may not be available from Ransomes and may need to be specially ordered from the supplier e.g. Volvo hydraulic
motor components.
QUANTITIES
Quantities shown are for one assembly or sub-assembly.
USING THE PARTS LIST
Determine the function and application of the part required. Turn to the main index page and select the appropriate
section. Locate the part on the illustration and parts list and read off the quantity from the appropriate MODEL column.
NUMERICAL INDEX
This is a summary of all part numbers used in the manual arranged in numerical sequence and showing the page and
item number under which the parts appear.
ORDERING OF SPARE PARTS
When ordering replacement parts, it is most important to quote the SERIAL NUMBER of the machine, PART NUMBER,
DESCRIPTION and QUANTITY required.
Anyarbitrarymodifications carried outonthis machine mayrelievethe manufacturer ofliabilityfor any resulting
damageorinjury.
ABBREVIATIONS
N/A NotAvailable
AR AsRequired

GB-4
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
GB
3 SAFETY INSTRUCTIONS
This safety symbol indicates important safety
messages in this manual. When you see this
symbol, be alert to the possibility of injury, carefully
readthemessagethatfollows,andinformother
operators.
3.1OPERATINGINSTRUCTIONS
• Ensure that the instructions in this book
arereadandfullyunderstood.
• Nopersonshouldbeallowedtooperate
this machine unless they are fully
acquainted with all the controls and the
safetyprocedures.
• Neverallowchildrenorpeopleunfamiliar
with these instructions to usethis
machine. Local regulations may restrict
theage oftheoperator.
3.2SAFETYSIGNS
• It is essential all safety labels are kept
legible, if they are missing or illegible they
must be replaced. If any part of the
machine is replaced and it originally
carried a safety label, a new label must be
affixedtothe replacementpart. New
safetylabelsareobtainablefrom
Ransomesdealers.
3.3STARTINGTHEENGINE
• Before starting the engine check that the
brakesareapplied,drivesareinneutral,
guards are in position and intact, and
bystandersareclearof themachine.
• Do not run the engine in a building without
adequateventilation.
3.4DRIVINGTHEMACHINE
• Beforemovingthemachine,check to
ensure that all parts are in good working
order,payingparticularattentionto
brakes, tyres, steering and the security of
cuttingblades.
• Replace faulty silencers, mow only in
daylightorgoodartificial light
• AlwaysobservetheHighwayCodebothon
andoffthe roads.Keepalert andawareat
all times. Watch out for traffic when
crossingornearroadways.
• Stopthe bladesrotating beforecrossing
surfacesotherthangrass.
• Rememberthatsomepeoplearedeafor
blind and that children and animals can
beunpredictable.
• Keeptravellingspeedslowenoughforan
emergencystoptobeeffectiveandsafe
at all times, in any conditions.
• Removeoravoidobstructionsinthearea
to be cut, thus reducing the possibility of
injurytoyourselfand/orbystanders.
• Whenreversing,takespecial care to
ensure that the area behind is clear of
obstructionsand/orbystanders. DO
NOTcarrypassengers.
• Keep in mind that the operator or user is
responsibleforaccidentsorhazards
occurringto otherpeople ortheir
property.
• When the machine is to be parked,
storedorleftunattended,lowerthe
cutting means unless the transport locks
arebeingused.
• Whilemowing,always wearsubstantial
footwearandlongtrousers. Donot
operatetheequipmentwhenbarefootor
wearingopensandals.
• Checkthegrasscatcherfrequently for
wearordeterioration. Afterstriking a
foreignobject. Inspect. thelawnmower
fordamageandmakerepairsbefore
restartingandoperatingtheequipment.
• Ifthemachinestarts tovibrate
abnormally,checkimmediately.
3.5TRANSPORTING
• Ensure that the cutting units are
securelyfastenedin thetransport
position. Do not transport with cutting
mechanismrotating.
• Drivethemachinewithdueconsideration
ofroadandsurfaceconditions, inclines
andlocalundulations.
• Suddendeceleratingorbrakingcan
cause the rear wheels to lift.
• Remember that the stability of the rear of
the machine is reduced as the fuel is
used.
3.6LEAVINGTHEDRIVINGPOSITION
• Parkthemachineonlevelground.
• Beforeleavingthedrivingposition,stop
theengine andmake sureall moving
parts are stationary. Apply brakes and
disengagealldrives.Removethestarter
key.

GB-5
GB
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
3 SAFETY INSTRUCTIONS
3.7SLOPES
TAKEEXTRACAREWHENWORKINGON
SLOPES
• Localundulations andsinkage willchange
thegeneralslope.Avoidgroundconditions
which can cause the machine to slide.
• Keep machine speeds low on slopes and
duringtightturns.
• Suddendeceleratingorbrakingcancause
the rear wheels to lift. Remember there is
no such thing as a “safe” slope.
• Travelongrassslopesrequiresparticular
care.
DONOTUSEONSLOPESGREATERTHAN15°
IMPORTANT: When working on any slope set the
weight transfer, if fitted to its maximum (+) setting.
3.8BLOCKEDCUTTINGCYLINDERS
• Stoptheengine andmakesure all moving
partsarestationary.
• Applybrakesanddisengagealldrives.
• Release blockages with care. Keep all parts
of the body away from the cutting edge.
Bewareofenergyinthedrivewhich can
causerotationwhenthe blockage is released.
• Keepotherpeopleawayfrom the cutting units
as rotation of one cylinder can cause the
others to rotate.
3.9ADJUSTMENTS,LUBRICATIONAND
MAINTENANCE
All vehicles
• Stoptheengine andmakesure all moving
partsarestationary.
• Applybrakesanddisengagealldrives.
• Readalltheappropriateservicinginstructions.
• Use only the replacement parts supplied by
theoriginalmanufacturer.
• When adjusting the cutting cylinders take
carenotto get handsandfeet trapped when
rotatingcylinders.
• Makesurethatother people are nottouching
any cutting units, as rotation of one cylinder
can cause the others to rotate.
• Toreduce thefire hazard,keep theengine,
silencerandbatterycompartmentsfreeof
grass,leavesorexcessivegrease.
• Replacewornordamagedpartsforsafety.
• Whenworkingunderneathliftedpartsor
machines,makesureadequatesupport Is
provided.
• Do not dismantle the machine without
releasingorrestrainingforceswhichcan
causepartsto move suddenly.
• Donotalterenginespeedabovemaximum
quoted in Engine Specification. Do not
changetheenginegovernorsettingsor
overspeedtheengine. Operatingtheengine
at excessive speed may increase the hazard
ofpersonalinjury.
• Whenservicing batteries,DONOTSMOKE,
and keep naked lights away.
• Do not place any metal objects across the
terminals.
Diesel & Petrol vehicles
• Whenrefuelling,STOPTHEENGINE,DO
NOTSMOKE.Addfuelbeforestartingthe
engine,neveraddfuelwhiletheengineis
running.
• Useafunnelwhenpouring fuelfrom acaninto
the tank.
• Do not fill the fuel tank beyond the bottom of
the filler neck.
• Replace all fuel tank and container caps
securely.
• Storefuelin containersspecificallydesigned
forthispurpose.
• Refueloutdoorsonly anddonot smoke while
refuelling.
• If fuel is spilled, do not attempt to start the
enginebutmovethemachineawayfrom the
areaofspillageandavoidcreatinganysource
ofignitionuntilfuelvapourshavedissipated.
• Allow the engine to cool before storing in any
enclosure.
• Neverstore theequipment withfuel inthe
tankinsideabuilding where fumes mayreach
anopenflame orspark.
• If the fuel tank has to be drained, this should
bedoneoutdoors.
• Do not spill fuel onto hot components.
LPG vehicles
• Only trained & competent personnel in the
useofLPGas a roadvehiclefuelare
allowed to work on LPG aspects of the
vehiclesengineorfuelsystem.
• Whenrefuelling,STOPTHEENGINE,DO
NOTSMOKE.Addfuelbeforestartingthe
engine,neveraddfuelwhiletheengineis
running.
• Vehicles should not be parked within 3
metersofanyheatsource, open flame or
othersourcesofignition.
• Vehiclesshouldnotbeservicedoveran
inspection pit
• If for any reason a leak in the fuel
systemis suspected,the vehicle
should be moved to an isolated area
clear of buildings & people and as far
as possible from drains and any source
of ignition.

GB-6
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
GB
DANGER-Indicatesanimminentlyhazardous
situation which, if not avoided, WILL result in
deathorserious injury.
WARNING-Indicatesapotentiallyhazardous
situationwhich,ifnotavoided,COULDresult
in death or serious injury.
CAUTION-Indicatesapotentiallyhazardous
situationwhich,ifnot avoided, MAY resultin
minorormoderateinjuryandproperty
damage. It may also be used to alert against
unsafepractices.
IMPORTANT: Transport speed is for highway
use only. Never select transport speed
on grass areas or uneven or unsurfaced
roadsortracks.
TheoperatingInstructionsfortheCuttingUnitsare
contained in a separate Publication .
• Thefuelfillerbayonetonthevehicleshould
beinspectedregularlyfor any signsof
damage.
• The gas used to fill the vehicle must be
sourcedfromareputablesupplier.
• If a machine starts to vent gas when it is
runningitshouldbemovedtoanarea
awayfromany sources ofignitionand
stopped. If it vents when static the
machine should not be started, all
potentialsourcesof ignitionshouldbe
inhibiteduntil theventing hasstoppedand
thelocalRansomesJacobsendealer
shouldbecontacted.
• WherepracticalLPGfuelledvehicles
should be parked in the open air, in a well
ventilated position. Where this is not
reasonably practical due to lack of space,
security ect. vehicles should be parked
insidesuitablydesigned buildingsor
garages. Pleasereferto HELA publication
LACNo.52/6rev

GB-7
GB
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
3 SAFETY INSTRUCTIONS
California Proposition 65
EngineExhaust,someofitsconstituents,
and certain vehicle components contain
or emit chemicals known to the state of
California to cause cancer and birth
defects or other reproductive harm.
WARNING
Batteries produce explosive gases and
contain corrosive acid and supply levels
of electrical current high enough to cause
burns.
WARNING
Battery posts, terminals and related
accessories contain lead and lead
compounds
WASHHANDSAFTERHANDLING
WARNING
Hydraulic Fluid escaping under pressure
can penetrate skin and do serious
damage. Immediate medical assistance
mustbesought.
WARNING
Before releasing transport latches it is
important that all cutting units are fully
raised.
1. Park the machine on level ground.
2. With the engine running at operating
speed raise the cutting units to their
maximum position by operating lift
levers whilst seated in the driving
position.
3. Disengage drives, stop the engine and
make sure all moving parts are
stationary. Apply brakes and remove
the starter key.
4. transport latches can now be released.
WARNING
DONOTUSEONSLOPESGREATERTHAN15°
WARNING
VENTINGGASCANCAUSEFROSTBITE
WARNING

GB-8
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
GB
4 SPECIFICATIONS
4.1 ENGINESPECIFICATION
4.1.1 DIESEL
TYPE: Kubota25Kw@3000rpm,4
cylinder(in-line)verticalDiesel
engine,4-stroke,watercooled,
1335cc, with 12v electric start.
Model: V1305-BBS-EC-1
MaximumSpeed: 3150±50 RPM(Noload)
IdleSpeed: 1500+100RPM
Oil Sump Capacity: 6 litres
Fuel: No.2-DDieselfuel(ASTMD975)
CoolantCapacity: 5litres50/50Anti-freeze
CoolantSpecification :Ethyleneglycolanti-freezewith
softenedwater.
4.1.2 LPG
TYPE: Ford25Kw@3000rpm,4
cylinder(in-line)verticalPetrol
engine,4-stroke,watercooled,
1297cc, with 12v electric start.
Model: VSG413
MaximumSpeed: 3150±50 RPM(Noload)
IdleSpeed: 850 ± 50 RPM
Oil Sump Capacity: 3.1 litres
Fuel: LPG(Propane)
CoolantCapacity: 5litres50/50Anti-freeze
CoolantSpecification: Ethyleneglycolanti-freezewith
softenedwater.
4.2 MACHINESPECIFICATION
Frameconstruction: Heavydutyformedsteelchassis.
Transmission: Hydrostaticpowerprovidedbya
servo-controlledtransmission
pump.Driving2indivdualwheel
motorswithDiff-lock facility.
4WD:Driving4individualwheel
motorswithapatentedparallel
series transmission system.
Selectableforwardallwheeldrive
lockandreversefrontaxlediff-
lock facility.
Cuttingunitdrive: Hydraulic,withforward,neutral,
reversecontrolvalve.Electric
dashmountedswitchforon/off
control,withfloormountedswitch
forcyclinderengage.Handcontrol
valveforreelspeedadjustment
Speeds:
Cutting: 12 km/h
Transport: 25 km/h
21 km/h (4WD)
Reverse: 6 km/h (4 mph)
Steering: Hydrostaticpoweredsteeringto
rearwheels.
Groundpressure: Normallyastyre pressure
Brakes,Service: Positivehydrostaticbraking.
Parking: Fail safe, Oil immersed wet disc
brakes.
FuelTank
CapacityDiesel: 45 Litres
CapacityLPG: 72Litres
HydraulicTank
Capacity: 35Litres
Battery: Exide093
4.3 DIMENSIONS
Width of cut: 2.14metres
Transportwidth: 1.5metres
Overallheight: 1.56metres
Overalllength: 2.68metres
Overallweightof
machine:
Diesel 1276Kg*
1302Kg*(4WD)
LPG 1304Kg*
1330Kg*(4WD)
* With 6 knife fixed head sport 200 units, full fuel
tank, and optional Lighting and Beacon kits
WheelTrack: 1.5metres
Wheel Base: 1.5metres
UncutCircle: 0.66metresRadius
0.75metresRadius(4WD)
SERUSSERPERYT
tcudorP leehWtnorF leehWraeR
eziSeryTepyTeryTerusserPeryTeziSeryTepyTeryTerusserPeryT
DW40312yawhgiH21-05.01x32 rp6carTitluMnatiTisp02-41rab73.1-00.1 8-05.8x5.81 rp4carTitluMnatiTisp02-41
r
ab73.1-00.1
)ralveK(xxamfruTsixxaM rp4s561-Cnrettapdaert isp22-02rab05.1-73.1 )ralveK(xxamfruTsixxaM rp4s56
1-Cnrettapdaert isp22-02
r
ab05.1-73.1
DW20312yawhgiH21-05.01x32 rp6carTitluMnatiTisp02-41rab73.1-00.1 8-00.01x02 rp4natiTisp02-41
r
ab73.1-00.1
)ralveK(xxamfruTsixxaM rp4s561-Cnrettapdaert isp22-02rab05.1-73.1 )ralveK(xxamfruTsixxaM rp4s56
1-Cnrettapdaert isp22-02
r
ab05.1-73.1

GB-9
GB
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
4 SPECIFICATIONS
ERUTAREPMETYTISOCSIVLIO
)F°93(C°4EVOBA03EAS
)F°93(C°4WOLEB03-W01ro03-W5EAS
0312yawhgiH KD/SC/UC/JWseireS noitareleccAmrA/dnaH level
HRroHLxaM
s/msnoitareleccA
2
qeAXqeAYqeAZ
313,0953,0422,0
eulaVtnanimoD
953,0
0312yawhgiH UC/JWseireS KD/SC/ ydoBelohW noitareleccA level
noitacoLroolF
s/msnoitareleccA
2
noitacoLtaeS
s/msnoitareleccA
2
xyzxyz
naeM8420,09510,02570,0010,0<0910,03310,0
4.4 VIBRATIONLEVEL
Themachinewastestedforwholebodyandhand/
armvibrationlevels. Theoperatorwasseatedinthe
normaloperatingpostionwithboth handsonthe
steeringmechanism. Theenginewasrunningand
the cutting device was rotating with the machine
stationary.
StandardISO5349:1986 Mechanicalvibration.
Guidelinesforthemeasurementandthe
assessmentofhumanexposuretohand-
transmittedvibration.
StandardISO2631-1:1985Evaluationofhuman
exposuretowholebodyvibration --Part1:
Generalrequirements.
4.5 SLOPES
DONOTUSEONSLOPESGREATERTHAN15°
The slope 15° was calculated using static stability
measurementsaccordingtotherequirementsof
EN836.
4.6 RECOMMENDEDLUBRICANTS
Engineoil: ShouldbetoMIL-L-2104Corto
A.P.I. Classification SE/SF/SG
grades.[10W-30]
4.7CUTTINGPERFORMANCE
47 cuts per meter at 12 km/hr with 8 knife floating
headunits.
65 cuts per meter at 12km/hr with 11 knife floating
headunits.
24 cuts per meter at 12 km/hr with 4 knife fixed head
units.
35 cuts per meter at 12 km/hr with 6 knife fixed head
units.
4.8CUTTINGPERFORMANCE(AREA)
2.3 Hectares/hour at 12 km/hr with float head units.
2.3 Hectares/hour at 12 km/hr with fixed head units.
A10%allowanceisincludedfornormal overlapsand
turning at the end of each cut.
HydraulicOil: Shell Tellus 46 to ISO VG46, or
equivilant
Grease: ShellDarinaR2,orequivilant.

GB-10
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
GB
5 LUBRICATION AND MAINTENANCE
5.1 LUBRICATION AND MAINTENANCE CHART DEISEL POWERED MACHINES
serudecorpecnanatniampohskrowerastnioptellubetihW
yliaD /ylkeeW yrevE sruoh04
tsriF 05 sruoh yrevE 001 sruoh yre
vE 002 sruoh yrevE 004 sruoh yrevE 008 sruoh dnE fo nosaeS
ENIGNE
levelliokcehC
z
lioegnahC
z z
tnemeleretlifriakcehC
z
tnemeleretlifriaecalpeR
z
leveltnalooCkcehC
z
tnalooCegnahC
z
egdirtracretliflioecalpeR
z z
retlifleufenilnicitsalpecalpeR
z z
retawrofretlifleufkcehC noitanimnatnoc
z
.retsinnacretlifleufecalpeR
z
neercsguBnaelC&kcehC
z
ENIHCAM
erusserperytkcehC
z
leveldiulfciluardyhkcehC
z
sirbedrofyabenignekcehC
z
ssenthgitrofstlob&stunkcehC
z
rofsgnittifciluardyhkcehC ssenthgit
z
noitidnocyrettabkcehC
z
tnemeleretlifciluardyhecalpeR sA dnE/deriuqeR nosaesfo
liociluardyhegnahC
z
fodnerO nosaes
esaerg2RaniraDllehShtiwgniwollofehtetacirbuL
toviPelxA
z
stoviPelxAbutS
z
)DW2(sgniraeBleehwraeR
z
dne-doRmaRgnireetS
z
sdne-doRegaknilgnireetS
z
stekcarbtoviptinU
z
stovipmratfiL
z
sgniraebrednilycgnittuC
z
sgniraeblloR
z

GB-11
GB
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
serudecorpecnanatniampohskrowerastnioptellubetihW
yliaD /ylkeeW yrevE sruoh04
yrevE 002 sruoh yrevE 004 sruoh yr
evE 008 sruoh dnE fo nosaeS
ENIGNE
levelliokcehC z
lioegnahC z
tnemeleretlifriakcehC z
tnemeleretlifriaecalpeR z
leveltnalooCkcehC z
tnalooCegnahC z
egdirtracretliflioecalpeR z
neercsguBnaelC&kcehC z
sgulPkrapSecalpeR z
ENIHCAM
erusserperytkcehC z
leveldiulfciluardyhkcehC z
sirbedrofyabenignekcehC z
ssenthgitrofstlob&stunkcehC z
rofsgnittifciluardyhkcehC ssenthgit z
noitidnocyrettabkcehC z
tnemeleretlifciluardyhecalpeR sA dnE/deriuqeR nosaesfo
liociluardyhegnahC zfodnerO nosaes
esaerg2RaniraDllehShtiwgniwollofehtetacirbuL
toviPelxA z
stoviPelxAbutS z
)DW2(sgniraeBleehwraeR z
dne-doRmaRgnireetS z
sdne-doRegaknilgnireetS z
stekcarbtoviptinU z
stovipmratfiL z
sgniraebrednilycgnittuC z
sgniraeblloR z
5.2 LUBRICATION AND MAINTENANCE CHART LPG POWERED MACHINES

GB-12
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
GB
5 LUBRICATION AND MAINTENANCE
5.3 ENGINE - Diesel: First 50 working hours
and every 200 working hours.
Change Engine Oil.
(a) Warm up the engine first and then shut it
off.Removeoildrainplugfromthebottom
of the crankcase and wipe it off.
(b) Replace thedrainplugandfill enginewith
6.4 litres of oil.
Change Engine Oil Filter.
(a) Removesingle-unitcartridge(A)
(b) Apply thin coat of oil to cartridge gasket
beforeinstalling.
(c) Tighten filterbyhandonly.
(d) Check foroilleaksaround thecartridge
gasket after engine is started.
LUBRICATION.
5.3.1 ENGINE - LPG: Every 200 working hours.
Change Engine Oil.
(a) Warm up the engine first and then shut it
off.Removeoildrainplugfromthebottom
of the crankcase and wipe it off.
(b) Replace thedrainplugandfill enginewith
3.1 litres of oil.
Change Engine Oil Filter.
(a) Removesingle-unitcartridge(A)
(b) Apply thin coat of oil to cartridge gasket
beforeinstalling.
(c) Tighten filterbyhandonly.
(d) Check foroilleaksaround thecartridge
gasket after engine is started.

GB-13
GB
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
5.4 MACHINE: Lubricate the following
points.Weekly or every 40 working hours.
1.LubricatethefollowingwithShellDarinaR2
grease.
(a) Lift armpivots (A).
(b) Cutting unitpivots(B).
(c) Axlecentrepivot(C).
(d) Axle stub shaft pivot(D)
(e) Steeringramrodend(E)
(f) Steeringlinkagerod ends(F)
(g) Cuttingcylinderbearingsandrollbearings.
(Wherelubepointsarefitted)
(h) Rearwheelbearings (2WD Only)
(i) Steeringrammount(G)
(j) SpannerHeightofCutAdjusters(Where
fitted)
2 . Lubricate the following with engine oil:
DivertorValvespools.
5 LUBRICATION AND MAINTENANCE
LUBRICATION.

GB-14
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
GB
5.6 MACHINE: Every800WorkingHours.
ChangeHydraulicOil.
1. RemovedrainpluginbottomofHydraulic
tankandwipeoffplug.
2. Allowtankto drainandreplace plug.
3. Refill tank with 35 litres of Shell Tellus 46 Oil.
IMPORTANT-Whenevertheclosedlooptransmission
circuit has been broken into it is essential
that the circuit is flushed prior to use.
Absolutecleanlinessmustbeobservedwhen
filling the hydraulic tank. Oil must be filtered
througha25micronfilterbeforeenteringthe
hydraulictank.
5.7 HYDRAULICTESTPOINTS.
Thereare5testpointsavailableon themachine for
conducting hydraulic system checks.
• Forwarddrivepressure(A)
• Reversedrivepressure(B)
• Chargepressure(C)
• Cuttingcylinderdrivepressure(D)
• Liftandpowersteeringpressure(E)
LUBRICATION.
5 LUBRICATION AND MAINTENANCE
5.5 MACHINE: Every400WorkingHours.
LubricationofDirectDriveHydraulicMotor(Every400
hours)
Lowerallcuttingunitsontolevelground.Beforeleaving
thedrivingposition, stopthe engineandmake sureall
movingpartsarestationary.Applybrakesand
disengagealldrives.removethestarterkey.Thedirect
drivehydraulicmotorcanberemovedfromthecutting
unitbyremovingthetwoscrewsandwashersholding
themotortothebearinghousing.Carefullywithdraw
themotorfromthe bearing housing,itis important not
tocontaminatethe motor shaftorinternal splinesof
thecuttingcylinder.If foranyreasonthey are
contaminated,theyshouldbecleanedbydegreasing.
Liberallylubricatethe motorandcylindersplineswith
ShellS7222grease beforereassembling.

GB-15
GB
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
5.8 ENGINEMAINTENANCE-DIESEL
Every100hrs
Fuel System.
UseDieselfuelNo.2-D(ASTMD975)
Seeenginemanufacturer'smanualforadditional
information.
Water Separator - If water is not removed from the
fuel,extensivedamagecanbe donetothe fuel
injection system.
1. Withengineoff,open vent (A)attopof
waterseparator.
2. Opendrainvalve(B)atbottomofwater
seperator to allow any water to drain out.
3. If water is present, it will drain first. When
fuelemergesfromthevalve(B),closethe
valve.Closethevent(A).
NOTE: Failureto drainwaterreducesfuelfilter
efficiency.
Bleeding air from fuel system
1. Turn the ignition switch to the ON position
(don'tstartengine).
2. Openairvent(C) onsideof injectionpump
to allow air to escape.
3. Retightenairvent.
4. TurnignitiontoOFF.
MAINTENANCE
5 LUBRICATION AND MAINTENANCE

GB-16
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
GB
5.9 ENGINEMAINTENANCE-DIESEL
Every400hrs
ReplaceIn-linefuel(C)
Cleaning the air filter
Removeloosedirtfromelementwithcompressedair
working from the clean to dirty side, using
compressed air max 6 bar , with nozzle 5cm from
element.
Change air filter (Or every 6 cleanings)
1. Raisebonnet.
2. Removeendcapofairfiltercartridge.
3. Removeaccumulateddustordirt.
4. Removefilterelement(B)(pullstraightout
firmly)
5. installnewfilterelement(pressfirmly
againstrearshoulder)
6. Replaceendcap and fastenwithclips
NOTE: Extensivedamagetoenginecanresultfrom
aninadequateairsupply.
MAINTENANCE
5 LUBRICATION AND MAINTENANCE
5.9.1 ENGINEMAINTENANCE- LPG
Every400hrs
Cleaning the air filter
Removeloosedirtfromelementwithcompressedair
working from the clean to dirty side, using
compressed air max 6 bar , with nozzle 5cm from
element.
Change air filter (Or every 6 cleanings)
1. Raisebonnet.
2. Removeendcapofairfiltercartridge.
3. Removeaccumulateddustordirt.
4. Removefilterelement(B)(pullstraightout
firmly)
5. installnewfilterelement(pressfirmly
againstrearshoulder)
6. Replaceendcap and fastenwithclips
NOTE: Extensivedamagetoenginecanresultfrom
aninadequateairsupply.

GB-17
GB
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
Other Regular Service.
• Verifyproperoperationofsafetyinterlock
switches (Parking Brake, Seat switch,
etc.)
• Ensure nuts and bolts remain tight.
• Keep tyre pressure at 1kg/cm2(14psi).
• Followtheenginemanufacturer’s
maintenancerecommendations.
• Ifalabelbecomeswornorremoved,see
the LABELS section of this manual or the
tractorPartsManualforreplacement
information.
NOTE: Whenwashingmachinewithpressurespray
washersorsteamcleaners,avoidwashingbearingareas
becausecleaningsolutionsmightpenetratebearingseals
andcauseprematurebearingfailure.
5.11 MACHINEMAINTENANCE
Battery.
Keepfluidlevelsabovebatteryplates.
MAINTANACE
5 LUBRICATION AND MAINTENANCE
5.10 ENGINEMAINTENANCE-DIESEL
Every400hrs
Changing fuel filter
1. Unscrewfilter(A)fromfilterhead.
2. Removewater(B)separatorfromfilterand
discardfilter.
3. Fitwater separatortonew filterandrefit
filtertohead.
4. Bleed air from system as describe in section
5.6.
Storage
• Storepetrolordieselfuelinanapproved
container in a cool dry place.
• Keep the machine and fuel containers in a
lockedstorageplacetopreventtampering
and to keep children from playing with them.
• Donotstore fuelorpetrol/diesel fuel
poweredequipmentinanyclosedarea
whereheatingappliances,pilot lights or any
sort of open flame is present.
• Beforestoring,allowthe engine to cool,and
drainfuelcompletelyfromfuel tanksand
containers.
• Maximum safety and best mowing results
can only be expected if the mower is
maintainedandoperatedproperly.
Weareyeprotectionwhenservicingbattery.
WARNING
Battery posts, terminals and related
accessories contain lead and lead
compounds
WASHHANDSAFTERHANDLING
WARNING

GB-18
RANSOMES HIGHWAY 2130
MAINTENANCE AND PARTS MANUAL
GB
5 LUBRICATION AND MAINTENANCE
5.12 END OF SEASON or when required
Change Hydraulic filter.
1. Lowerthecentrecutting unitto improve
access.
2. Wipe filter bowl (A) and housing to remove
any dirt present.
3. Place a suitable drip tray on top of the centre
cutting unit.
4. Unscrewbowlandremoveoilfilterelement
and disposes of safely.
5. Replacewithnewelement.
6. Coat the top outside lip of the filter bowl with
a thin film of oil and refit filter bowl and
torque to 54Nm, as indicated on decal.
7. Start engine and idle for 15 seconds.
8. Stop engine, check filter bowl for leaks and
checkreservoir
NOTE: It is important that absolute cleanliness
isobservedwhenchangingthefilter.
Change Coolant.
1. Completelydrainthe coolingwaterfromthe
radiatordrainplug(B)andflush thecooling
systemwithflushing detergent.
2. Check for leaks or loose connections at the
radiator, cylinder head gasket, drain cock etc.
3. Mix antifreeze coolant and water at the
specifiedratiobeforepouringintotheengine.
Note: When topping up the cooling system fill with a
50/50solution.
Check Rear Wheel Bearings. (2WD Only)
1. Jack up, and securely chock the rear of the
machineusingpoints indicatoredin
section 5.2
2. Checkforfree-playinbearings,
3. Iffree-playisfoundremovedustcoverand
split pin and tighten castlated nut till all free-
play is eliminated.
MAINTENANCE