Raritan Elegance User manual

Toilet
Installation and Maintenance Instructions
1-800-352-5630
www.raritaneng. com
Desription:
Marineelegancetoiletisavailablein12Vor24V
DC.Bowlsareavailableinfourmodels:standardwith
angledback,standard with straight back, tall with
angledbackandtallwithstraightback.Freshwater
modelutilizesonboard freshwater,theSea water
modelutilizesaremotepumpinstalledbetweenraw
watersourceand bowl. Sea/Fresh modelcanswitch
betweenfresh and raw watersource.
Threedifferentcontroloptionsareavailable:
1. Smartflushcontrol: providestimed operation
andindependantcontrolofwateranddischarge
2. MEtoiletcontrol:provides momentaryopera-
tionand independantmomentarycontrolofwater
anddischarge
3. Pushbuttonswitch:providingonlytheabilityto
flushwith no independantcontrolofwateror
Marine
EleganceElegance
EleganceElegance
Elegance
THE FOLLOWING ARE CAUTIONARY STATEMENTS THAT MUST BE READ AND
FOLLOWED DURING BOTH INSTALLATION AND OPERATION.
WARNING: RaritanEngineeringCompany,Inc.recommendsthataqualifiedpersonorelectricianinstall
this product. Equipment damage, injury to personnel or death could result from improper
installation. Raritan Engineering Company, Inc. accepts no responsibility or liability for
damagetoequipment,injuryordeathtopersonnelthatmayresultfromimproperinstallation
or operation of this product.
WARNING: HAZARD OF SHOCK OR FIRE
Alwaysuserecommendedfuse,circuitbreakerandwiresize.
Motors used with this product are “Ignition Protected”. They are not however, explosion-
proofasdefinedin46CFR110.15-65(e),SubchapterJ-ElectricalEngineering.
DONOTruncontinuouslyformorethan30seconds.
Pressurized
Freshwater Model
Sea Water Model
(Remote Pump)

SAFETY
2
IMPORTANTSAFETYINSTRUCTIONS:
WARNING:
Youngchildrenshould NOTbeleftunsupervised
aroundtoilet. Seriousinjuryordeathcould
occur.
Childrencan drown in water retained inthe
bowl.
Seatand/orlidcouldcloseand strike child.
Alwaysreplacecircuitbreakerandfuses with
samerating.UseRaritanparts
tomaintainignitionprotection
requirements.
Toiletsmounted at or below thewaterlinemusthavea
ventedloopinstalledinthedischarge line. The top of
theventedloopmustbeaminimumof4"(10cm)above
the waterline at the boats greatest angle of heel (see
ventedloopmanufacturer’sinstructions).
SeaWaterModelsmustalsohaveaventedloopinstalled
betweentheintakepumpandthetoiletbowl.
Doubleclampallbelowwaterlineconnections.
RecommendedVisualInspection
33
33
3Forleaksattoilet and hose connections
33
33
3Hoseclamps
33
33
3Conditionof hoses
33
33
3Seacocks
33
33
3Conditionof wiresandconnections
33
33
3In-LineStrainer (ifyouhaveone)
• Nospecialtoiletpaper is required.
• Water should appear in the bowl within ten
seconds. Ifnot,seetroubleshootingsection.
• Hardobjects orstringysubstances(papertowels,
femininehygieneproducts, filter cigarettes, etc.)
mustnotbethrownintothetoiletastheywillcause
damage.
• Alwaysshutoffseacock(s)beforeleavingtheboat
unattended.
WARNING: HAZARD OFFLOODING -Alwaysshutoffseacock(s)beforeleavingtheboatunattended.
Double clamp all below waterline hose fittings and check frequently for integrity.

OPERATION
3
A. PushButtonSwitch:
Presspush-buttonswitchandholduntilallwaste
iscleared from the toilet bowl.
B.METoiletControl:
1. Press and hold “Water Only” to add water
tothebowl
2. Pressandhold“Empty”toevacuatethebowl
3. Press and hold “Flush” to bring water in
whilebowlisevacuating
C.MultifunctionSmartSwitch:
1. EmptyOnly:Press Empty Only button to
evacuatethebowl.Dischargepumprunsas
longas thisbuttonisheld.
2. WaterOnly: PressWater Only switch to
addwater in thebowl.Inletwatersolenoid/
pumpruns aslongasbuttonispressed with
asevensecondslimit. Afterlimitisreached
WaterOnly button is disabled to prevent
overflowofthebowl.Toenableagain,Empty
Onlybuttonmustbepressed.
3. Normal: Press normal button once and
timedflushingcyclestarts.
4. Watersaver:Press the button andawater
savercyclestarts.
NOTE:Holdingtankfulllightwillonlyilluminateif
thetank sensor has been added to thecontrol.

OPERATION
4
NOTE: Flush control is set at factory to work in most
installations and no additional programming is needed.
Use following instructions to re-program if adjustment
on water levels and timings are needed.
Programming timing for “NORMAL” flush cycle:
Normal cycle has initial fill time (T1), Discharge pump
time (T2), and water retention fill time (T3).All three
times (T1,T2 and T3) are programmable.
Factory setting : T1=3 sec, T2=2 sec, T3= 3 sec,
To change any of the above settings re-programming is
needed
Step 1 – Placing the unit in program mode:
Hold the WATER ONLY & EMPTY buttons down
together for three seconds. The Holding Tank Full
LED will give three quick flashes indicating you have
entered program mode - release both buttons.
Setting T1 initial fill time:
After placing the unit in program mode (Step 1 above)
push the “Normal Flush” button the number of times
required for the Water Valve/Inlet Pump time (one
push = 1 sec’s, two = 2 sec’s., etc.) the Tank LED
will flash once indicating a valid key push.
Note: If the button is pushed 9 times it will start back
at 2 seconds. Once this is done, push the EMPTY
button to store this value (the unit will flash three times
indicating the time has been set and you have left
program mode).
Setting T2 Discharge Pump Time:
After placing the unit in program mode (Step 1 above)
push the EMPTY button the number of times required
for the Discharge Pump time (one push = one second,
etc.) the Tank LED will flash once indicating a valid
key push.
Note: If the button is pushed 9 times it will start back
at 1 second. Once this is done push the NORMAL
button to store this value (the unit will flash three times
indicating the time has been set and you have left
program mode).
Setting T3 Water retention fill Time:
After placing the unit in program mode (Step 1 above)
push the WATER ONLY button the number of times
required for the Water Valve/Inlet Pump time (one
push = ZERO sec’s, two = 1 sec. three = 2 sec’s.,
etc.) the Tank LED will flash once indicating a valid
key push. Note: If the button is pushed 9 times it will
start back at zero.
Once this is done push the “NORMAL” button to
store this value (the unit will flash three times
indicating the time has been set and you have left
program mode).
Programming the WATER ONLY Disable
Features:
1. Hold the WATER ONLY & EMPTY buttons
down together for three seconds. The holding
tank full LED will give THREE flashes indicat-
ing you have entered program mode .
2. Push the WATER SAVER button. TheWATER
ONLY and EMPTY buttons now can be dis-
abled or enabled:
3. Pushing the WATER ONLYbutton will disable
both WATER ONLY and EMPTY buttons. The
holding tank full LED will give THREE flashes
indicating you have left program mode.
Repeat steps 1 to 3 to re-enable these buttons.
The WATER ONLY button can be set to only
work after the EMPTY button has been
pushed: (prevents children from flooding the toilet)
To program this feature
1. Repeat steps 1 and 2 above
2. Pushing the EMPTY button will enable this
feature. The holding tank full LED will give
THREE flashes indicating you have left
program mode. Repeat steps 1 and 2 to disable
these features.
Programming the Holding Tank Full Lockout
Disable Features:
1. Hold the WATER ONLY & EMPTY buttons
down together for three seconds. The holding
tank full LED will give THREE flashes indicat-
ing you have entered program mode .
2. Push the WATER SAVER button. This will
place control in disable/enable mode
3. Pushing the WATER SAVER button again. The
holding tank full LED will give THREE flashes
indicating you have left program mode.
Repeat steps 1 to 3 to re-enable Holding Tank Full
Lockout feature..
Programming of Toilet Flush Control

WINTERIZING
Winterizing:
• Improperwinterlayupisamajorcauseofmarine
toiletfailure.
• Useonlynontoxicantifreeze.
• Flush toilet several times to clear waste from
system.
• Disposeofallantifreezeinaccordancewithlocal
andfederalregulations.
• Winterize holding tanks, plumbing, treatment
systems(MSD’s), etc. independently following
manufacturer’sinstructions.
PressurizedFreshwaterModels
PartsRequired
• 1"(25 mm.) or 1 1/2" (38 mm.)I.D.
dischargehose,approximately3feet(1m.)long
• Twobuckets
• Nontoxicantifreezeapproximately1quart
(1liter)
Steps
1. Close discharge seacock (ifoneexists).
2. Shut off intake wateratsource.
3. Turnoffpowertounit.
4. Disconnect and drain dischargehose.
5. Disconnectintakehosesfromwatersolenoid and
placeinone of the buckets.
6. Connectshorthosetotoilet’sdischargeandplace
inotherbucket.
7. Pourantifreezeinbowl.
8. Turnonpowertounitandflushuntilantifreezeis
removedfromthebowlandwaterisdrainedfrom
thesolenoidandhose.
9. Disconnect power to toilet.
10. Reconnectintakehoses to water solenoid
Integraland RemoteIntake Pump Models
PartsRequired
3/4"(19mm.)I.D.intakehoseapproximately 3 feet
(1m.) long.
1" (25 mm.) or 1 1/2" (38 mm.) I.D. discharge hose
approximately3 feet (1 m.)long.
Twobuckets
Nontoxicantifreeze approximately1quart(1liter)
Steps
1. Close the intakeanddischarge seacocks.
2. Turnoffpowertounit.
3. Disconnect and drain intake hose and discharge
hose .
4. Connectshort hosestotoilet’sintakeanddischarge.
5. Place one bucketunder hose connectedtotoilet’s
discharge.
6. Pour nontoxic antifreeze in other bucket.
7. Place hose connected to intakepump into bucket
with antifreeze.
8. Turn on power to unit and flush toilet until
antifreeze begins to be discharged from toilet.
9. Disconnectpowerfromtoilet.
RECOMMISSIONING
1. Using the buckets, hoses and approximately one
gallon (3.8 liters) of clean fresh water, flush
antifreeze out of the toilet (see Winterizing).
Dispose of antifreeze in accordance with local
and federal regulations.
2. Reconnect the intake and discharge hoses and
open both seacocks and water source valve.
3. Check all connections for leaks with several test
flushes. SYSTEM START-UP
1. Open seacock(s).
NOTE: Pressurized freshwater models; open water
source valve.
2. Turn on power to toilet.
3. Flush toilet per Operation Instructions.
4. Check for leaks.
IMPORTANT: If toilet does not flush properly
or if water does not enter the bowl within 10
seconds, refer to Troubleshooting.
5

SPECIFICATIONS
6
Pressurized Freshwater Model - Recommended Wire and Fuse/Circuit Breaker Size
Sea Water Model - Recommended Wire and Fuse/Circuit Breaker Size
Plumbing
NOTES: for Wiring
teeF 01510252030405
reteM 1.36.41.66.72.92.212.51
pmupekatnIfonoitcusmumixaM )enilretawevobathgiehmumixaM( .pmuPekatnImorf)m2.1(.tF4
pooldetnevegrahcsidfo
thgiehmumixaM .teliotfoesabmorf)m3(.tF01
ecruosretawdezirusserP muminim
stnemeriuqer
ta)sretil52.31(mpg5.3
foetarwolf )apK07(isp01 .)aPk5.43(isp5foerusserpffotuhs
.1 .ecruosotkcabdnatinuotecruosmorferasecnatsiD
.2 nehwdedulcniebTSUMpmupekatnietomerotecruosrewopmorfec
natsiD dnaesabrewolrofdesuebTSUMeziseriwemaS.ecnatsidlatotgninimreted .pmupekatnietomer
.3 mm(GWAmuminime
riwrotcudnocdednemmoceR
2
.pordegatlov%3rof)
.4 501nodesaberasezisrotcudnocdednemmoceR
o
.noitalusnidetarC.sgnitarnoitalusnirehtorofsdradnatSCYBAotrefeR
.5 .tinuotremrofsnartmorfsnoitacificeps
CDV42esustinuCAV042/021roF
stinU egatloV
tiucriC esuf/rekaerB )spma(ezis
ecnagelE teliot
ward.pmA lanimon@ /egatloV
etomeR pmuP ylnO
ward.pmA lanimon@ egatlov
51 teef 02 teef 03 teef 04 teef 05 teef
CDV21038101GWA01GWA8GWA6GWA6GWA4
CDV4202015
GWA41GWA41GWA21GWA01GWA01
stinU egatloV
tiucriC esuf/rekaerB )spma(ezis
ward.pmA lanimon@ egatlov
01 teef 51 teef 02 teef 03 teef 04 teef 05 teef
CDV215281GWA21GWA01GWA01GWA8GWA6GWA6
CDV425101GWA41GWA21GWA01GWA01GWA8GWA6
F
D
E A
C
SIZE
See Table
G
Hose Sizes
INLET 1/2”(12.7mm.) forfreshwater model
3/4”(19mm.)forseawater model
Discharge
1”(25.4mm.) or1 1/2”(38mm.)
B
CONVERSIONS
Wire - AWG to mm2
Feet to Meters
GWA 614121018642
mm
2
5.15.20.40.60.010.610.520.53

7
SPECIFICATIONS
AdditionalPartsRequired
• 1"(25mm.)or11/2"(38 mm.)I.D. discharge hose
• 3/4"(19mm.)I.D.reinforcedintake hose
• 3/4"(19mm.) and 1" (25mm.)or 1 1/2" (38mm.)
hose clamps (two for each connection below
waterline)
• Wire
• Terminals
• Fuse/circuitbreaker
14
NOTE:
12
1. Each 90 degree Elbow is equal to 4 feet of hose
2. Each insert coupling is equal to 2 feet of hose
3. Each Y-valve is equal to 10 feet of hose
Example
: An installation has 50' of straight run with two elbow and a
1
0
Y- valve, what is maximum height of loop allowed?
Answer: equivalent hose length = 50' +8'(two elbows)+10'(Y-valve)
Vertical height (Feet)
= 68
'
From chart horizontal distance of 68' gives a vertical dist. @ 7
'
8
Hence a maximum of 7' high loop can be installed.
6
4
2
0
2
0
4
0
6
0
8
0
10
0
0
12
0
14
0
16
0
18
0
Horizontal distance (Feet)
MarineElegance dischargeMaximum recommended1” PVChose length
Parts included with all models
1.Toiletbowl assembly
2.Mountingbracketkit
3. Seat
4.Oneofthefollowingflushcontrols:
a.PushButtonControl
b.METoiletControl
c.MultifunctionSmartControl
5.UserguideandInstallationguidewithlabels
Additional Parts included with sea
water model:
1.Remotepump assy.
2.Relayforremotepump
Bowl type A B C D E F G
ME-
angledback 18 3/8 (467) 12 1/4 (311) 14 (355) 12 (305) 14 (355) 8 1/2 (216) 2 1/8 (54)
ME-
straightback 18 3/8 (467) 12 1/4 (311) 14 (355) 12 (305) 14 (355) 8 1/2 (216) NA
ME-TALL
angled back 18 3/8 (467) 12 1/4 (311) 17 (432) 15 (380) 14 (355) 8 1/2 (216) 2 1/8 (54)
ME-TALL
Straight back 18 3/8 (467) 12 1/4 (311) 17 (432) 15 (380) 14 (355) 8 1/2 (216) NA
SIZE
inch(mm.)

8
MOUNTING
A. Preparation for Mounting Toilet
Mountingsurface mustbe flatand solid.
Seat must open more than 90 degrees.
1. Place the toilet and mark mounting holes’
center line, and outside of the bowl
(seeFIG1.) Drawacenterlinebetween two
holes. Markfrontholeoutsideandcenterand
drawa line perpendicular tofirstcenterline.
2. Markthree linesA, B, and C, 3/8”fromoutside
lines.
3. Lineupoutsideedgesofthebrackets withmarked
linesA,B, and C.
4.Secure the bracket assembly to deck using #14
self threading bolts andflatwashers.
Note:placeboltsas close to mark linesA,B,and
Cas possible
5. Drill holes for discharge (1 5/8” (41 mm.), inlet
hose(7/8”(22mm.)andwires(3/4”(19mm.)using
dimensionsshowninFig. 2.
Note: check outside diameter of the hoses and
adjustholesizesaccordingly.
6. Complete plumbing and wiring before installing
toilet
25/8”
21/4”
DISCHARGEHOSE
15/8” (41 mm.)
INLETHOSE
7/8”(22mm.)
WIRES
3/4”(19mm) 2”
13/8”
Fig.1
LineA LineB
LineC
Fig.2
To install the toilet:
A. Preparemounting location
B. Install plumbing
C. Installcontrols and completewiring
D. Connecthosesandwiringto toilet
E. Mounttoilet
3/8”
Boltand
washer

Discharge Lines
1. Connectqualitysanitationhose1"(25mm.)or
11/2”(38mm.)dischargefitting ontoilet.
2. Runhosetoappropriatedevice(i.e.: treatment
system,holding tank, etc.).
Inlet lines
1. Connect 1/2”(13 mm.) hose to pressurized
supplyor3/4”(19mm.) hose to remotepump
PLUMBING
B. PLUMBING
WARNING: HazardofFlooding
Toiletsmountedatorbelowthewaterlinemust
have a vented loop installed in the discharge
line. The top of the vented loop must be a
minimum of 4" (10 cm.) above the waterline
atthe boatsgreatest angle ofheel (seevented
loopmanufacturer’sinstructions).
Sea Water Models must also have a vented
loop installed between the intake pump and
thetoiletbowl.
Doubleclampallbelow-waterlineconnections.
IMPORTANT
• Fittingsand90° bendsshouldbekept toa
minimum.
• In-Line Strainer may be installed on Sea
Water Models per Installation
Instructions. Thiswillprevent clogs.
• Discharginguntreatedsewageisforbidden
in all U. S. waters within the three-mile
limit.
• Thru-hull fittings and seacocks must be
installedwhere theyare easilyaccessible.
• Useonly qualityreinforced hoses suchas
RaritanSH.
• Secure all hoses properly.
Waterline
Remote Intake Pump Model
Mounted below Waterline
Pressurized Freshwater Model
Installed Above/below Waterline
Discharge
Pressurized
Freshwater
Source
Shut off
Valve
Waterline
remote
pump
Electroscan
Waterline
Discharge
Seacock
Waterline
Discharge
Vented
Loop Intake Vented
Loop
Discharge
Seacock Intake
Seacock
Electroscan
Pressurized Freshwater Model
Installed below Waterline
9
Holding Tank

10
PLUMBING
Intake Lines
PressurizedFreshwaterModels
Installashutoffvalveinintakelinebeforewatersolenoid
valve.
1. Connect hose from shut off valve to inlet port of
watersolenoid valve at the toilet.
NOTE: Toavoidmalfunction of water solenoiddueto
debrisin water, installationof Freshwater Strainer
(190601)isrecommended.
Remote Sea Water Models
Intakepumpfittings are interchangeable to allow more
flexibilityduring installation. Inletportsarelocatedon
eithersideofintakepump. Outletport(totoiletbowl)is
attopof intake pump.
NOTE: Toavoidpoorpumpperformanceinstallation
ofstrainer(163000)isrecommended
1. Slidefittingclipstoopenposition.
2. Select inlet portto be used.
3. Installappropriatefittingsintoinletandoutletports.
NOTE: The90° fitting canbe rotated 360°.
4. Installtheplugfittingintounusedinletport.
IMPORTANT: Be sure not to install plug fitting
intooutletport! Damageto pumpwilloccur!
5. Slidefitting clipsbacktoclosedposition.
6. Connecthosefromseacocktoinletportof optional
In-Line Strainer if installed. Use hose clamp
provided.
7. Connecthosefromoutletport ofIn-LineStrainerto
inletportofintakepump. Usehoseclampprovided.
IMPORTANT: Double clampall belowwaterline
hoseconnections!
8. Connect hose from outlet port of intake pump to
bowlelbowlocated on back oftoilet bowl.
From
Seacock
To Intake
Pump
Arrow
Open Closed
Plug
From
Strainer
Inlet Ports
Outlet Port
To Bowl
Inlet
port
Discharge
port

WIRING
C.Mounting controls:
A. PushButton Switch: (see fig 11)
• MountPush ButtonSwitchinanaccessible
location.
• Makecertain wires canbe routed to Push
ButtonSwitch.
• Wireterminalsmusthaveclearancewhen
installed.
1. Drill5/8"(16mm)hole.
2. AttachwirestoPushButtonSwitchterminals(see
wiringsection).
3. Install Push Button Switch through back of
mountingsurface.
4. Installwaterproof nutonPushButtonSwitch.
5. Secureinplacewithinnernut.
B. ME Toilet Control:
1. Cut out a hole per Fig. 12, mark
mounting holesusingwallplateasguide.
2. Route wire to the toiletandcontrol.
3. Secure control with gasketusingtwo
screws.
C. SmartFlushControl:
1. Cut out a holeperFig.13,mark mounting
holesusingwallplateasguide.
2. Route wire to the toiletandcontrol.
3. Securecontrol usingmounting
screws
InstalltheWarningLabel (L322) whereit canbe
easily seen.
MountingRemotePump:
1. Locate remote pumpbetweenthruhullfitting and
toiletbowl.
2. Locate in anarea away fromberth to keepnoise
leveldown.
3. Use Inline Strainer(optional)toavoidclogs.
4. Secureremote pump to the floor using four bolts
throughthe pump base.
11
Fig.11
1/4”minclearancefrom terminals
CUTOUT
MultifunctionalManualSwitch Fig. 12

12
D. WIRING
WARNING: Hazardof Shockand Fire
• Alwaysuseproperwire,wireconnectorsand
fuse/circuit breaker. See Specification
Chart.
• Secure wire properly.
• Do not connect appliances to toilet circuit.
• Make sure power is off before proceeding.
• Use proper wire terminals for all wire
connections.
1. Determineproperwiresizebymeasuringdistance
from:
• PowerSourcetopush button to toilet motor
and back to power source.
• Remote pump units - also include distance
from power source for remote pump to
remote pump and back. Same wire gauge
mustbe usedforbothlower baseandremote
pump.
2. Select proper wireand fuse/circuit breakersize
fromSpecificationsonInstallationpage.
3. Installfuse/circuitbreakerinpositivelineatsource.
4. Wirecontroltothetoiletandbatteryusingone of
thefollowingwiringdiagrams.
WIRING
TostartElectroscanfrom toiletcontrol,runawire
from“to EST“toterminalmarked “EXTTRIG”
insideElectroscan control module(blackbox).
TostartEleganceequippedwithSmart Switch from
Electroscan,connect“Head1” to “FROM EST“.
ForLectra/SanMC,callRaritan Customer Service
ELECTROSCANOPERATION
SmartFlushControl Fig. 13
CUT
OUT

WIRING
BATTERY
Fuse
RED
Orange
Black
RED
Black
Solenoidvalve
Dischargepump
Fig. 14 Wiring for Push Button Switch
Fresh water model
ToEST
Dischargepump
Black
RED
Blue
Blue
Black
RED Fuse
Pump
Relay
RED
PushButton
PushButton
BATTERY
13
Fig. 14A Wiring for Push Button
Switch Remote pump model
ToEST

WIRING
14
GND
Valve-
orange
black red
black red black
BATT-
Pump-
EST
valve+
pump+
BATT+
panel
holdingtankfull
fromEST
toESTEXTTRIG
BATT
FLUSH
CONTROL
PANEL
FUSE/BREAKER
orange
black
red
black red
black
panel
tankfullswitch
ESTinput
BATT
FLUSH
CONTROL
PANEL
FUSE/BREAKER
Relay
PUMP
remote
Fig.15 WIRINGFOR SMARTSWITCH FRESHWATERMODEL
Fig.16 WIRINGFORSMARTSWITCH REMOTE PUMPMODEL
blue
SolenoidValve
DischargePump
DischargePump
blue
BATT+
pump+
valve+
EST
Pump-
Valve-
GND
toESTEXTTRIG
BATT-

15
WIRING
orange
black
black
red
black
red
FLUSH
CONTROL
PANEL
fuse/Breaker
BATT
ControlBox
BATT
red
blue
FLUSH
CONTROL
PANEL
pump
fuse/Breaker
red
orange
black
blue
black
red RED
Relay
Fig.18 WIRINGFOR METOILET CONTROLWITH REMOTEPUMP
Fig.17 WIRINGFORMETOILETCONTROL FRESHWATERMODEL
SolenoidValve
DischargePump
DischargePump
ToEST
Panel
+DISCHARGE
+INLET
+BATT
EST
-DISCHARGE
-BATT
-INLET
+DISCHARGE
+INLET
+BATT
EST
-DISCHARGE
-BATT
-INLET
ToEST
black
ControlBox
Panel

16
5. Route wirefrom controlperwiringdiagrams.
6. Install seat. I nstall discharge supportstrapbetween
seatnut and the bowl perFig. 19A.
7. Installtoilet inplace,connecthosesand wireplugs.
(seeFig. 19)
Caution:Donot pull on thedischarge hosetoavoid
kinking
8. Installmountingbushings,bolts.(SeeFig.20)
9. Tightenboltsbeingcarefultonotovertighten(Do
notexceed30inchlb.whentightening)
10. Installcapsovermountingbolts.
D.Connect Hoses andwiring to toilet
E. Mount toilet
Fig.19
Fig.20
Fig.19A
Dischargesupportstrap
INSTALLATION

17
TROUBLESHOOTING
WARNING: HAZARDOFELECTRICSHOCK-Beforebeginninganyworkonthetoilet,besurethatallpower
totheunithasbeenturnedoff.
WARNING: HAZARDOFFLOODING-MakesureseacocksareintheCLOSEDorOFFpositionbeforework-
ingontoilet.
NOTE: Thefollowinginformationreflectsthemostprobablecausesandsolutionstoproblemsalthoughnot
everypossiblecauseandsolutionisprovided.
AnyquestionsregardingservicingoroperationoftheMarineEleganceshouldbedirectedtoourTechnicalSupport
DepartmentinMillville,NJorFt.Lauderdale,FL. Pleasehavemodelandserialnumberavailablebeforecalling.
PROBLEM
1. Poorpumpout,especially
solids.
2. Poorwaterflow,especially
atfront ofbowl(ornowa-
terflow).
3. Foulodorsfromtoiletarea.
4. Bowlfillswhileunderway.
5. Waterleakingfromunder
unit.
POSSIBLE CAUSE
1A. Cloggeddischargeline.
1B. Plumbingrestrictions,bendsandells.
1C. Cloggedvents.
1D. Mineralbuildupinhosesandfittings.
1E. Lowvoltage.
2A. Toiletnotlevel.
2B. Restriction inintakeline.
2C. Pumpsuckingair.
2D. Lowvoltage.
2E. Cloggedstrainer.
3A. “Marine life” lodged in rim of bowl.
3B. Permeateddischargehose.
3C. Sewageremainingindischargeline.
4A. Pressurebuildupatseacocks.
5A. LeakingBowlThroatadapter.
5B. Leakatshaftseal.
5C. Leakfrombowlspud.
SOLUTION
1A. Besuredischargeseacockisopen. Clearline,remove
clog.
1B. Replumbtoeliminatebendsandells.
1C. Cleanholdingtankventandventedloopvents
1D. Cleanorreplaceaffectedparts.Replacehoseifneeded.
1E. Check voltage attoilet while toilet is running. If
lessthan nominalvoltageoftoilet(12 or24),check
conditionofbatteriesandwiresizes.Checkterminals
andwireconnectionsforcorrosion(heatatterminals
andjunctionsindicatesabadorcorrodedconnection).
2A. Raiserearoftoilet;checkwithlevel.
2B. Besureseacockisopen. Clearline-removeclog.
2C. Checkallconnectionsfromintakethru-hulltointake
pumptobesurenoairleaksarepresent.
2D. See1E,above.
2E. RemoveorCleardebrisfromstrainer.
3A. Removeandflushbowlwithpressurehosetoremove
allmaterial. Installstrainer inintakeline toavoidre-
currence.
3B. ReplacehosewithRaritansanitationhose(#SH).
3C. Flushtoiletlonger;replacehoseifpermeated;reroute
hosemakingashorterrunifpossible.
4A. Closeintake,thendischargeseacocktodetermine
whichiscausingproblem. Ifdischarge, besurethe
ventorvented loop is clean. Ifintake,thereistoo
muchpressureonseacock;contactRaritanTechnical
Support.
5A. Tightenadapterclamps.
5B. Checksealandmotorshaft.
5C. Checkandreseatbowlgrommet
TROUBLESHOOTING

EXPLODED PARTS
MarineElegancePARTSLIST
221100 Toilet Bowl,standard, angled, White(1)
221100A Toilet bowl Bone(1)
2210012 Discharge PumpAssembly (1)
221012 MOTOR: 12 VDC (1)
221024 MOTOR: 24V DC (1)
221105 O-RING (1)
221110 Discharge Pump Seal Plate (1)
221115 Discharge Pump Macerator Housing(1)
221120 Bowl Throat Adapter (1)
221125 Bowl ThroatAdapter Clamp (small)(1)
221130 Bowl Throat Adapter Clamp - Large (1)
221135 JOKER VALVE (Custom) (2)
221140 Discharge Hose (Custom)(1)
221145 DischargeAdapter Fitting(1)
221150 Uni Seal 1/2” (1)
221155 Discharge Pump Mounting Bracket(1)
221156 Discharge Mtg Bracket Straight Back Model
221160 Discharge Hose Clamp - Small (1)
221165 Discharge Hose Clamp - Large (1)
221170 Discharge hose strap(not shown)
221175 L bolts2(2) ( not shown)
221210 Bowl Mounting Bushing (2)
221215 Bowl Mounting Bushing Cap (2)
221300 Vacuum Breaker Assembly 1
221325 Vacuum Breaker Seal Washer (1)
221330 Vacuum Breaker O-Ring (#16)(1)
221351 Water Solenoid Valve (12V)(1)
221352 Water solenoid valve (24V)(1)
221355 Water Line Adapter (1)
221335 1/2" Hose 2.25" L (1)
221340 1/2" Clamps (2)
31-102 Motor Shaft Seal
31-114 Lock Nut 10-32 W/Nylon (3)
CH20B #10 Lock washer (not shown)
F321 Fender washer (not shown)
F186VT Bowl Mounting Screw: (2)
F187VT Bowl Mounting Screw (1)
F188 Well Nut (2)
F189 Deck Mounting (3)
F193VT Pump Mounting (1)
F195 Front mounting washer (1)
F196 Front mounting snap cap (1)
M23A Lockwasher
166000 Remote pump complete 12v
166100 Remote pump complete 24V
1660** Motor, raw water pump
161115 Impeller
161123 Macerator Blade
* Specify DC Voltage (12, 24, 32)
162135 Cone Seal
162225 O-Ring
162305 Lower Housing includes #162315
162310 Diaphragm includes #162315
162315 Piston (4)
162320 Piston Seat (4) includes #162315
162325A Bearing PlateAssembly includes #162315
162405 3/4" Hose Barb - 90° Fitting
162410 3/4" Hose Barb - Straight Fitting (2)
162415 Plug Fitting
162420 Fitting Clip (3)
162425 Fitting O-Ring (4)
F005 Set Screw
F172 Piston Fastener (4)
F144 Mounting Bolt Washer (4)
F162VT Mounting Bolt
F199 Bushing
1108A Nut
Optional:
190601 Fresh water strainer
163000 Raw water strainer
NOT SHOWN;
221101 Toilet Bowl ,Standard,Straight White
231101 Toilet Bowl Tall Straight White
231100 Toilet Bowl TallAngledWhite
Note: add suffics “A “for bone
1245 Seat and cover, white
1245A Seat and cover , Bone
214** Relay
Control parts (not shown):
SSFC02 Smart Control Box
SSFC 03 Smart wall panel
SSFC04 Cable
31-603 Cable
For Momentary Multifunction control after 02/10
221549 Momentary Multifunction control box
221524 Momentary Multifinction Bazel White
221543 Momentary Multifinction wall panel
221545 Cable for Momentary Multifunctin control
Repair kits:
DIAPUMPRK inlet pump repair kit
162400 Fittings and O-rings for inlet pump
166000 Diaphragm pump complete 12V
166100 Diaphragm pump complete 24v
MERK Discharge pump repair kit
18

MarineEleganceExplodedPartsView
1222AW
F172
F005
162325A
162305
162320
162310
162315
162420
162405
162415
162410
162425
F144
F162VT
163000
1660*
M23A
162300W 162425
162425
162225
162135
162100W
162420
162200W
190601 - Recommended
EXPLODED PARTS
F193
freshwaterstrainer
Recommended
Seawater strainer
19
FIG21
221100
F186VT 221210
221110
221150 221300
161123 161115
31-102
221145
221155
221140
221115 2210**
221135(2)
221335
221351(12V)
221215
F199
F187VT
F196
221120
221352(24V) 221165
F195
221130 221125
221340(2)
221105
221160
221146
M23A
1108A

L460 0610vkm Specifications Subject to Change Without Notice Printed in U.S.A.
530 Orange Street, Millville, NJ 08332 USA
Telephone: [phone] FAX: [phone]
www.raritaneng.com
Southern Office and Plant:
3101 SW Second Avenue, Fort Lauderdale, FL 33315 USA
Telephone: [phone] FAX: [phone]
LIMITED WARRANTY
RaritanEngineeringCompanywarrantstotheoriginalpurchaserthatthisproductisfreeofdefects
inmaterialsorworkmanshipforaperiodofoneyearfromtheproduct’sdateofpurchase. Should
thisproductprovedefectivebyreasonofimproperworkmanshipand/ormaterialswithinthe
warrantyperiod,Raritanshall,atitssoleoption,repairorreplacetheproduct.
1. TOOBTAINWARRANTYSERVICE,Consumermustdelivertheproductprepaid,togetherwith
adetaileddescriptionoftheproblem,toRaritanat530OrangeSt.,Millville,N.J.08332,or3101SW
2ndAve.Ft.Lauderdale,FL33315. Whenrequestingwarrantyservice,purchasermustpresenta
salessliporotherdocumentwhichestablishesproofofpurchase.THERETURNOFTHEOWNER
REGISTRATIONCARDISNOTACONDITIONPRECEDENTOFWARRANTYCOVERAGE.
However,pleasecompleteandreturntheownerRegistrationCardsothatRaritancancontactyou
shouldaquestionofsafetyarisewhichcouldaffectyou.
2. THISWARRANTYDOESNOTCOVERdefectscausedbymodifications,alterations,repairsor
serviceofthisproductbyanyoneotherthanRaritan;defectsinmaterialsorworkmanshipsupplied
byothersintheprocessofinstallationofthisproduct;defectscausedbyinstallationofthisproduct
otherthaninaccordancewiththemanufacturer’srecommendedinstallationinstructionsorstandard
industryprocedures;physicalabuseto,ormisuseof,thisproduct.Thiswarrantyalsodoesnotcover
damagestoequipmentcausedbyfire,flood,externalwater,excessivecorrosionorActofGod.
3. ANYEXPRESSWARRANTYNOTPROVIDEDHEREIN,ANDANYREMEDYFORBREACH
OFCONTRACTWHICHBUTFORTHISPROVISIONMIGHTARISEBYIMPLICATIONOR
OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. ALL IMPLIED
WARRANTIES SUCH AS THOSE OF MERCHANTABILITY AND OF FITNESS FOR A
PARTICULAR PURPOSE, IF APPLICABLE, AS WELL AS ANY IMPLIED WARRANTIES
WHICH MIGHT ARISE BY IMPLICATION OF LAW, ARE EXPRESSLY LIMITED TO A
TERMOFONEYEAR. SOMESTATESDONOTALLOWLIMITATIONSONHOWLONGA
LIMITEDWARRANTYLASTS,SOTHEABOVELIMITATIONMAYNOTAPPLYTOYOU.
4. UNDERNOCIRCUMSTANCESSHALLRARITANBELIABLETOPURCHASERORANY
OTHER PERSONS FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER
ARISINGOUTOFBREACHOFWARRANTY, BREACHOFCONTRACT,OROTHERWISE.
SOMESTATESDONOTALLOWTHEEXCLUSIONORLIMITATIONOFINCIDENTALOR
CONSEQUENTIALDAMAGES,SOTHEABOVELIMITATIONOREXCLUSIONMAYNOT
APPLYTOYOU.
5. Nootherpersonorentityisauthorizedtomakeanyexpresswarranty,promiseoraffirmationoffact
ortoassumeanyotherliabilityonbehalfofRaritaninconnectionwithitsproductsexceptas
specificallysetforthinthiswarranty.
6. Thiswarrantygivesyouspecificlegalrights,andyoumayalsohaveotherrightswhichvaryfrom
statetostate.
20