Raypak PS270VSP User manual

Catalog No. 6200.183 Replaces: NEW Effective. 06/2013
P
O
W
E
R
S
A
V
E
R
CLEAN
OVERRIDE
HIGH
OVERRIDE
LOW
BACK
POWER
FAULT
+
-
SET
12
3
4
5
6
Controls &
LEDs Description
1 Display Screen
2 LED Lights
Power: Light (Green)
Fault: Light (Red)
3 BACK: returns to previous
program setting and does NOT
accept current screen values
4 Navigation Selector
+ or – increases/decreases
selected value
← or → Navigates to adjust-
able value (digit)
SET accepts the current
screen values
5 Interface Selector
6 Override Buttons
NOTE: The selector knob must be
turned to RUN for the pump to oper-
ate. When the user presses ← or →
button the cursor moves to the next
or previous position. If the cursor is
at the end of a line when the user
presses the arrow, the cursor moves
to the next line.
PS270VSP
Quick Start Guide
User Interface & Navigation Overview
WARNING: This product must be installed and serviced by a qualied pool professional,
and must conform to all national, state, and local codes. Before installing this product,
read and follow all warning notices and instructions of this product. Failure to follow
warning notices and instructions may result in property damage, personal injury, or
death.
Only the clock setting is required to enable the PS270VSP to operate at three different
speeds and durations using the pre-set schedule. The preset speeds and schedule
times are detailed in the manual on page 14.
Observe all safety warnings and cautions
Verify the user interface is plugged in
Make certain the motor is properly wired
Turn selector knob to SET CLOCK
Set the Time and Date using the +, -, ←, → buttons
Turn the Selector knob to RUN
NOTE: Must wait until “PRIME MODE” is complete to make changes to OVERRIDE
settings.
Pre-set Schedule

P
O
W
E
R
S
A
V
E
R
CLEAN
OVERRIDE
HIGH
OVERRIDE
LOW
BACK
POWER
FAULT
+
-
SET
11/11/2011
11:26 AM
SET CLOCK
6. Press + or – to change the Hour. Press → to move to the Minute setting.
7. Press + or – to change the Minute. Press → to move to the AM or PM setting.
8. Press SET when the time is correct.
9. Press SET again if the user needs to make additional changes. The cursor returns
to the Month setting.
10. If date and time are correct, turn the Selector Knob to SET SCHEDULE, STEP 1.
Setting the Clock
1. Turn Selector Knob to SET CLOCK.
2. Adjust the Time and Date.
3. Turn the Selector Knob to SET SCHEDULE (STEP 1, 2, 3)
4. Set the Motor Speed, Start, and Stop times for STEP 1, 2, 3.
5. Turn the Selector Knob to SETUP (Use ← and → to scroll thru SETUP items)
Enable/Disable Freeze Protection
Set Display Screen Contrast
Set External Relay Speed and Time
Set Prime Speed and Duration
Reset Factory Defaults (Will return programmed schedule to Factory
Defaults)
6. Turn Selector Knob to RUN.
7. Press OVERRIDE HIGH button (Not required to run normal schedule)
8. Press SET to change OVERRIDE HIGH speed and duration.
9. Press OVERRIDE LOW button (Not required to run normal schedule)
10. Press SET to change OVERRIDE LOW speed and duration.
Custom Schedule
NOTE: The clock must be set the rst time the
pump is powered-up for proper operation.
1. Turn the Selector Knob to SET CLOCK.
2. At any time, the user can press BACK to
return to the previous screen.
3. Press + or – to change the Month. Press →
to move to the Day setting.
4. Press the + or – to change the Day. Press →
to move to the Year setting.
5. Press + or – to change the Year. Press → to
move to the Hour setting.
Raypak Inc. 2151 Eastman Avenue, Oxnard, CA 93030 [phone] FAX [phone] www.raypak.com