RCAT PRESTIGE User manual

High Wall / Low Wall Air Conditioner
Model
TECHNICAL MANUAL
PRESTIGE
RCAT
RCAT

CONTENUTI
1.1 INTRODUCTION
1.2 SAFETY INSTRUCTIONS
1.3
1.4 HANDLING
1.5
1.6 GENERAL FEATURES
1.7 TECHNICAL FEATURES
1.8 EXPLODED VIEW
RECEIVING THE GOODS
PARTS LIST
1.9 SPARE PARTS LIST
2.0 PAPER TEMPLATE
2.1 DRILLING THE WALL
2.2 INSTALLATION OF AIR PIPES AND GRATINGS
2.3 FITTING THE UNIT DRAINAGE LINE
2.4 FITTING THE UNIT ON BRACKET
2.5 ELECTRIC DIAGRAM
2.6 COOLING CIRCUIT
3.0 REMOTE CONTROL
3.1 REMOTE CONTROL FUNCTIONS
3.2 MAINTENANCE
3.3 PROBLEM SOLVING
ENVIRONMENTAL INFORMATION :
This product has been manufactured to comply with EEC Directives 2006/95/EG and 89/336/EEC
this equipment contains fluorinated greenhouse gases covered by
the Kyoto Protocol. It should only be serviced or dismantled by professional trained personnel.
GAS R410A, GWP ( Global Warming Potential ) = 1975
This marking indicates that this product should not be disposed with other household wastes throughout the EU.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources.
To return your used device, please use the return and collection systems or contact the Retailer where the product was
purchased ; they can take this product for environmental safe recycling.

1.1 INTRODUCTION
1.2 IMPORTANT SAFETY INSTRUCTIONS
PLEASE NOTE.
Do not dispose of any packaging until the installation of the equipment is completed.
(See list of accessories).
After having removed the packing, check that all the content is intact and complete.
In the event of missing parts, contact your retailer.
This unit has been designed to cool or heat the air of a room and should only be used for this purpose.
The manufacturer cannot be held liable for damage caused to property or injury to persons or animals due to
incorrect installation, maintenance or improper use.
This air-conditioner contains R410-A refrigerant: at the end of its life, the disposal of this equipment must be
in accordance with the strict regulation governing the recycling of this product, please operate with caution
during the disposal.
Please contact your local authority for regulatory advice.
Do not switch on before having totally assembled the unit and before installing in its correct operating
position.
Before starting the appliance, check that it is correctly earthed, according to the legislation in force in the
country concerned.
When using electrical appliances, basic safety precautions should always be followed:
1. Do not place objects on the product or allow objects to obstruct the inlet or outlet openings.
2. Extreme care should be taken when any product is used by, or near children and pets, and
whenever the product is left operating and unattended.
3. Please note: If you are drilling the hole above ground floor level, please ensure that an area has
been secured and while the holes are drilled the outside area is supervised, until drilling has been
completed.
4. Before operating the product remove the unit from its packaging and check it is in good condition.
5. Do not let children play with the packaging, for example plastic bags ; c
7. Do not operate any product with a damaged cord or plug, or after the unit malfunctions, has been
dropped, or damaged in any manner. Return the unit to an authorised service facility for examination
and repair to avoid a hazard.
8. Do not attempt to repair or adjust any electrical or mechanical functions on this unit as this may void
warranty, contact your service engineer.
9.
10. Always operate the product from a power source of the same voltage, frequency and rating as
indicated on the product identification plate.
11. This unit is not intended for use in wet or damp locations.
12. Do not place the unit near an open flame, cooking or heating appliance, or hot surface.
13. Do not let the power cord hang over the edge of a table or counter. Arrange the power cord away
from an area where it may be tripped over.
14. Never place the power cord under a carpet or rug. Do not operate the unit in areas where petrol,
paint, or other flammable liquids are used or stored.
hildren should be supervised
to ensure that they do not play with any part of the appliance.
6. This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
If the supply cord is damaged, it must be replaced by the manufacturer or its Service Agent or by a
similarly qualified person in order to avoid an hazard.

15. Do not carry out any cleaning or maintenance or access internal parts until the air-
conditioner has been disconnected from the mains electricity supply.
16. Do not alter the safety or regulating devices without the permission and instructions of the air-
conditioner manufacturer.
17. Do not pull, remove or twist the electric cable connected to the air-conditioner, even if disconnected
from the mains electricity supply.
18. Avoid prolonged direct contact with the flow of the air from the unit and the room being closed with
no ventilation for a long period of time.
19. If the fresh air intake duct is not installed, periodically open the windows to guarantee a correct
change of air.
20. Repair or maintenance work must be carried out by a service engineer or by qualified technicians in
compliance with the instructions given in this booklet. Do not alter the appliance, since hazardous
situations could be created while the manufacturer of the appliance will not be liable for any damage
or injury caused.
21.
This instruction booklet is an integral part of the appliance and should therefore be carefully preserved and
always accompany the appliance in the event of transfer to another owner or user or another installation
engineer.
Should the booklet be damaged or lost, please request an additional.
The air-conditioner is delivered in a protective packaging and is accompanied by an instruction manual.
This manual is an integral part of the air-conditioner and should therefore be carefully read and preserved.
When the unit is unpacked, please check that the equipment and the accessory pack are complete and
undamaged.
1.3 RECEIVING THE GOODS
If the fuse on PCB board is broken, be sure to replace the fuse with the same type as :
Rated voltage 250V, Rated current 3.15A. The fuse must be replaced by Manufacturer or its Service
Agent or a similarly qualified person.

1.4 HANDLING
To avoid any possible damages during transportation the unit is provided with compressor holders
that must be removed before installing the air conditioner ( see 2.6 ).
1. 5 PART LIST
1. FASTENING BRACKET
2. REMOTE CONTROL (Type V3)
3. INSTRUCTION MANUAL
4. PIPE FASTENING INNER FLANGE
5 AIR INTAKE ( 150MM ) AND AIR DISCHARGE ( 160MM ) PIPES
6. EXTERNAL GRIDS (Pre-installed in pipes)
7. RUBBER RINGS
8. PAPER TEMPLATE FOR WALL DRILLING
9. CONDENSATE HOSE
10. EXTENSION CONDENSATE HOSE
11. KIT OF SCREWS AND CABLE TIES
12. RING FIXING CORD x 2
- Be fully aware of the weight of the unit before attempting to lift it. Take all necessary precautions
to avoid damaging the product or causing personal injury.
- It is advisable to remove the packing only when the air-conditioner has been located in the point
of installation.
- Carefully remove the adhesive strips positioned on the air-conditioner.
- Packaging components must be disposed correctly and not left within reach of children, since
they are a potential source of danger.
4
4

1.6 GENERAL FEATURES
A : 55cm
L : 93cm
P : 23cm
OPERATING CONDITIONS IN COOLING AND DEHUMIDIFICATION MODE
OPERATING CONDITIONS IN HEATING MODE **
** At low ambient outdoor temperatures additional heating may be required to supplement the heat pump **
MIN : 18°C 70% R.H.
MAX : 43°C 45% R.H.
MIN : -5°C 80% R.H.
MAX : 24°C 45% R.H.
A
L
P
BLUE LED switched on: nigth mode is on RED LED switched on: the unit is in stanby
POWER CORD
GREEN LED switched on: compressor is on
YELLOW LED switched on: timer is on
SIDE COVER
DRAINAGE PIPE
FILTER GRATING
AIR DIRECTIONAL FLAP

1. 7 TECHNICAL FEATURES
Type
Through the wall
Technical data
Tension V , Hz, 220-240V 50 Hz
Cooling capacity (*1) W 3120
Consumption (cooling mode) * W 950
Absorbed current (cooling ) * A 3,90
Heating capacity (*2) W 3280
Consumption (heating mode) * kW 890
Absorbed current (heating) * A 4,50
E.E.R. W / W 3,51
C.O.P. W / W 3,69
Energy class in cooling mode A
Energy class in heating mode A
Pipes lenght m n° 2 pipes - 0,5 meters
Pipes holes diamater mm 155/165
Compressor type Rotary * high efficiency
Cooling gas R410-a
Cooling gas charge g 600
Noise level B(A) 36-45
Max air flow ( indoor ) m3/h 450
Max air flow ( outdoor ) m3/h 480
Max dehumidification capacity l/24h 21.6
Power cord lenght m 1,6
External diameter condensate drainage mm 30
Plug type Shuko
Dimensions (indoor) L xHxP** mm 930x550x230
Net weight (indoor) Kg 45
Technical features
Room thermostat Digital
Cooling circuit filter yes
Water pump condensate drainage Automatic
Condensate tray yes
Tangential fan air distribution yes
Auto-Swing mode yes
Fan speed 3 + AUTO
Sleep model yes
Ventilation mode yes
Dehumidification mode yes
Super silent mode yes
24h timer Elettronic
LED display yes
Infrared remote control yes
Manual restart mode yes
Wall mounted remote control support yes
Antibacterial filters + carbon filetrs + catalytic filters yes
Outdoor protection gratings yes
Air exchange optional yes
T - Prestigeechnical data sheet

1. 8 EXPLODED VIEW

1.9 SPARE PARTS LIST
Position n° ( see
exploded view ) Code Part description
1 81033600911 FLOATING HOLDER
2 82010402000 AXSL SLEEVE
3 81020400100 FLAT FRONT PANEL
4 81033601300D LED DISPLAY
5 81020400100B VISION LOW DECORATION PANEL
6 81020400200 VISION SWING
7 81010600500 CONDENSER FAN MOTOR SUPPORT
8 81013301400 CONDENSER FAN MOTOR BACK FOAM
9 81033601000D CONDENSER FAN MOTOR
10 81020400100A VISION UPPER DECORATION PANEL
11 81033602100D STEP MOTOR
12 81033601601 COMPRESSOR CAPACITOR
13 81010400400 CONDENSER FAN
14 81033601500 COMPRESSOR CAPACITOR CLIP
15 81010600600 MID BOARD SUPPORT
16 81020400400 FRONT PANEL SHORT PADDING
17 81020400401 FRONT PANEL LONG PADDING
18 81010601200 METAL GRILLE
19 81030401300 FRONT FIX BAR
20 81013300600 EVAPORATOR FRONT FOAM
21 81010600100 MID BOARD
22 81010400700 EVAPORATOR LEFT FRAME
23 81010600900 LEFT SIDE BOARD
24 81013300800 EVAPORATOR LEFT FOAM
25 81013300500 EVAPORATOR WIND TUNNEL FOAM
26 81020400250 EVAPORATOR WATER COLLECTOR
27 81033601400D EVAPORATOR FAN
28 81033600510D EVAPORATOR
29 81010601000 UPPER COVER
30 81010401500 EMERGENCY SWITCH COVER
31 81020400300 EVAPORATOR FILTER
32 81010401800 HEPA FRAME
33 81033600900D TRANSFORMER
34 81033600500D CONDENSER
35 81010601800D CONDENSER SIDE FRAME
36 81010601600 CONDENSER MID FRAME
37 81033600100D DRAINAGE PIPE
38 81010401700 NEW AIR-EXCHANGE CLIP
39 81010401600 NEW AIR-EXCHANGE SLICE
40 81010601100 LOW BACK COVER
41 81010401200 CONNECTOR ( FLANGE )
42 81010600300 UPPER BACK COVER
43 81010600700 FASTEN BRACKET
44 81033600200 160MM AIR OUTLET PIPE
45 81033600300 150MM AIR INLET PIPE
46 81010401000A WALL RING
47 81010401000D AIR INLET-OUTLET GRILLE
48 81033601100D REMOTE CONTROL
49 81033601101D REMOTE CONTROL HOLDER
50 81010601400 RIGHT SIDE BOARD
51 81030402400D PCB HOLDER
52 81033600800D MAIN PCB
53 82010401500 EVAPORATOR FAN MOTOR HOLDER
54 81033600700D EVAPORATOR FAN MOTOR
55 81013300700 EVAPORATOR RIGHT FOAM
56 81010400600 EVAPORATOR RIGHT FRAME
57 81013600104D EVAPORATOR FAN MOTOR CAPACITOR
58 81013300100 CONDENSER LOWER WIND TUNNEL FOAM
59 81013300200 CONDENSER UPPER WIND TUNNEL FOAM
60 81013300900 PUMP MAINTENANCE WINDOW FOAM
61 81033601600 COMPRESSOR
62 81010600400 COMPRESSOR BASE
63 81010601500 UNIT BASE
64 81013300300 CONDENSER FAN MOTOR FOAM
65 81010400900 PUMP HOLDER
66 81033600910 FLOATING SWITCH
67 81033600900 PUMP
68 81010400901 PUMP CLIP
69 81010400902 PUMP PIPE
70 81033600600 POWER CORD SCHUKO
71 81013600125 POWER CORD BUCKLE
72 81033602600 INNER WIRING
73 81013600112D 4-WAY VALVE
74 81033600912 TEMPERATURE SENSOR
75 81033601500D CONDENSER FAN MOTOR CAPACITOR
76 81010400800 DRAINAGE SPIGOT
PACKING MATERIALS
77 81013600114 INSTRUCTION MANUAL
78 81013600115 RATING LABEL
79 81013600116 CIRCUIT DIAGRAM STICKER
80 81013600120 EER LABEL
81 81013600123 - 81013600124 HEPA (ACTIVATED CARBON )
82 81013600119 NYLON CORD
83 81013600122 DRAINAGE EXTENSION
84 81013600121 PAPER TEMPLATE
85 81013600126 CARTON BOX
86 81033301500 LEFT PACKING FOAM
87 81033301600 RIGHT PACKING FOAM
88 81033301700 UPPER PACKING FOAM

2.0 PAPER TEMPLATE
Paper Template (copy to scale enclosed with accessories)
Fasten the template to the wall once the following guidelines have been thoroughly checked.
- Do not drill any holes until you are 100% confident that there are no obstacles in the area you wish to drill
and there are no obstructions, which could be hidden by the construction of the wall, for example: electrical
wiring water & gas pipes or supporting lintels or beams.
- Ensure that a sprit level is used, as the unit must be level.
- Follow the installation instructions & measurements in full.
HOT AIR
DISCHARGE
HOLE
AIR
INTAKE
HOLE
DRAINAGE HOLE
MINIMUM DISTANCE
FROM FLOOR
SIZE OF THE BRACKET
OBLIGATORY FIXING POINTS
EXTRA FIXING POINTS TO USE IF THE WALL IS NOT SOLID
MINIMUM DISTANCE
FROM CEILING
ELECTRICAL WIRING HOLE
165 mm
165 mm