Reliant One RSP130 Service manual

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and
others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for
future reference.
Description
This submersible pump is designed for home
sump applications. The unit is equipped with
a 9-ft long, 3-prong grounding type power
cord. Motor is oil filled and sealed for cooler
running and designed to operate under
water. A float switch is provided for
automatic pump operation. This pump is not
suitable for aquatic life.
Unpacking
Inspect this unit before it is used.
Occasionally, products are damaged during
shipment. If the pump or components are
damaged, return the unit to the place of
purchase for replacement. Failure to do so
could result in serious injury or death.
General Safety Information
Do not
use to
pump flammable or explosive
fluids such as gasoline, fuel oil,
kerosene, etc. Do not use in a
flammable and/or explosive
atmosphere. Pump should only be used to
pump clear water. Personal injury and/or
property damage could result.
This pump is not
designed to handle
salt water, brine, laundry discharge or any
other application which may contain caustic
chemicals and/or foreign materials. Pump
damage could occur if used in these
applications and will void warranty.
All wiring
must be
performed by a qualified
electrician. Failure to follow this
warning could result in fatal
electrical shock.
If the basement has
water or moisture on
the floor, do not walk on wet area until all
power is turned off. If the shutoff box is in
the basement, call an electrician. Remove
pump and either repair or replace. Failure
to follow this warning could result in fatal
electrical shock.
A backup system
should be used.
Wayne offers Model ESP15.
Installation
1. Install pump in a sump pit with minimum
size as shown in Figure 1. Construct sump
pit of tile, concrete, steel or plastic.
2. The unit should be located and rest on a
solid, level foundation. Do not place
pump directly on clay, earth, gravel or
NOTICE
!
DANGER
!
DANGER
NOTICE
!
DANGER
Operating Instructions and Parts Manual RSP130
352100-008 12/02
sandy surface. These surfaces contain
small stones, gravel, sand, etc. that may
clog or damage the pump and cause
pump failure.
Flood risk. If flexible
discharge hose is
used, make sure pump is secured in sump
pit to prevent movement. Failure to secure
pump could allow pump movement and
switch interference and prevent pump
from starting or stopping.
3. Thread check valve (Wayne offers Model
66005-WYN) into pump body carefully
to avoid stripping or cross threading. Do
not use pipe joint sealant.
4. Connect 1-1/2” rigid pipe to rubber boot
on check valve. Reverse boot for 1-1/4”
diameter pipe. Tighten hose clamps.
Support pump and
piping when
assembling and after installation. Failure to
do so could cause piping to break, pump to
fail, etc. which could result in property
damage and/or personal injury.
5. Protect electrical cord from sharp
objects, hot surfaces, oil and chemicals.
Avoid kinking the cord and replace
damaged cords immediately.
IMPORTANT: Make sure there is adequate
room for the switch to operate.
6. A sump pit cover must be installed to
prevent debris from clogging or
damaging the pump.
!
WARNING
!
WARNING
Operation
Always disconnect
the power source
before attempting to install, service, relocate
or maintain the pump. Never touch sump
pump, pump motor, water or discharge
piping when pump is connected to electrical
power. Never handle a pump or pump motor
with wet hands or when standing on wet or
damp surface or in water. Fatal electrical
shock could occur.
1. A ground fault circuit interrupter (GFCI)
is required.
Risk of
electrical
shock! This pump is supplied
with a grounding conductor
and grounding type attachment
plug. Use a grounded GFCI receptacle to
reduce the risk of fatal electrical shock.
Never cut off the round grounding prong.
Cutting the cord or plug will void the warranty
and make the pump inoperable.
2. This pump is only for use on 120 Volt
(single-phase), 60 hz, 15 amp service and
is equipped with a 3-
conductor cord and 3-
prong, grounding type
plug. Insert the power cord
plug directly into a 120 volt
GFCI-protected outlet. (See
Fig. 2)
3. Fill sump with water. The
pump will start automatically when the
water has filled the sump to the cut-in
level. The pump will stop when the
water reaches the cut-out level. See
specifications for cut-in/out levels. The
pump will recycle thereafter as required.
4. Do not operate the pump unless it is
submerged in water. Dry running causes
pump failure.
5The motor is equipped with an
automatic reset thermal protector.
6. While the pump is draining the pit, verify
that the discharge piping is carrying the
water to a point several feet away from
the foundation.
7. If pump discharge line is exposed to
freezing temperature, the exposed line
must be pitched to drain. Trapped water
will freeze and damage the pump.
!
DANGER
!
DANGER
© 2002 Wayne Home Equipment
24"
Min.
Grounded
Outlet
Figure 1
Submersible
Sump Pump
TEST RESET
Figure 2
Minimum Diameter 14”

2. Disassembly of the motor prior to
expiration of warranty will void the
warranty. If repairs are required, see
troubleshooting chart.
4. Inlet should be kept clean and free of
all foreign objects and inspect annually.
A clogged inlet will damage pump.
5. Pump should be checked monthly for
proper operation.
This pump contains
dielectric oil for
cooling. This oil can be harmful to the
environment. Check the state
environmental laws before disposing this
oil.
!
WARNING
Maintenance
Always
disconnect
the electrical supply before
attempting to install, service,
relocate or perform any
maintenance. If the power source is out of
sight, lock and tag in the open (off)
position to prevent unexpected power
application. Failure to do so could result in
fatal electrical shock. Only qualified
electricians should repair this unit.
Improper repair could result in fatal
electrical shock.
1. Let the pump cool for a minimum of
two hours before servicing because the
pump contains hot oil under pressure
and the motor is hot.
!
DANGER
Operating Instructions And Parts Manual
Troubleshooting Chart
Symptom Possible Cause(s) Corrective Action
Pump will not start or
run
Pump starts and stops
too often
Pump will not shut off
or thermal protector
turns off
Pump operates but
delivers little or no
water
1. Blown fuse
2. Low line voltage
3. Defective motor
4. Defective float switch
5. Impeller bound-up
6. Float obstructed
1. Backflow of water from piping
2. Faulty float switch
1. Defective float switch
2. Obstacle in piping
3. Float obstructed
1. Low line voltage
2. Plugged impeller
1. Replace with proper sized fuse or reset breaker
2. If voltage is under 108 volts, check wiring size
3. Replace pump
4. Replace float switch
5. Remove housing; remove blockage
6. Make sure float moves freely up and down
1. Install or replace check valve (Wayne check valve kit #66005-WYN)
2. Replace float switch
1. Replace float switch
2. Remove pump; clean pump and piping
3. Make sure float moves freely up and down
1. If voltage is under 108 volts, check wiring size
2. Clean out impeller
Specifications
Power supply requirements 120V, 60 hz
Motor Single phase, oil
filled
Liquid temperature range 40°F to 120°F
Circuit requirements 15 amps (min)
Dimensions 11” high x 9” base
Cut-in level (factory set) Tether 14”
Cut-out level (factory set) Tether 7”
Construction
Motor housing Thermoplastic
Volute Thermoplastic
Impeller Thermoplastic
Shaft Stainless steel
Seals Buna N
Discharge 11/2” NPT
Limited Warranty
For one year from the date of purchase, Wayne Home Equipment Division
("Wayne") will repair or replace, at its option, for the original purchaser any part or
parts of its Sump Pumps or Water Pumps (“Product”) found upon examination by
Wayne to be defective in materials or workmanship. Please call Wayne (800-237-
0987) for instructions or see your dealer. Be prepared to provide the model number
and the serial number when exercising this warranty. All transportation charges on
Products or parts submitted for repair or replacement must be paid by purchaser.
This Limited Warranty does not cover Products which have been damaged as a result
of accident, abuse, misuse, neglect, improper installation, improper maintenance, or
failure to operate in accordance with Wayne’s written instructions.
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR FROM THE DATE OF PURCHASE. THIS IS THE EXCLUSIVE
REMEDY AND ANY LIABILITY FOR ANY AND ALL INDIRECT OR CONSEQUENTIAL
DAMAGES OR EXPENSES WHATSOEVER IS EXCLUDED.
Some states do not allow limitations on how long an implied warranty lasts, or do
not allow the exclusions or limitations of incidental or consequential damages, so
the above limitations might not apply to you. This limited warranty gives you specific
legal rights, and you may also have other legal rights which vary from state to state.
In no event, whether as a result of breach of contract warranty, tort (including
negligence) or otherwise, shall Wayne or its suppliers be liable for any special,
consequential, incidental or penal damages including, but not limited to loss of profit
or revenues, loss of use of the products or any associated equipment, damage to
associated equipment, cost of capital, cost of substitute products, facilities, services or
replacement power, downtime costs, or claims of buyer’s customers for such damages.
You MUST retain your purchase receipt along with this form. In the event you need to
exercise a warranty claim, you MUST send a copy of the purchase receipt along with
the material or correspondence. Please call Wayne (800-237-0987) for return
authorization and instructions.
DO NOT MAIL THIS FORM TO WAYNE. Use this form only to maintain your records.
MODEL NO._______________ SERIAL NO.__________________________ INSTALLATION
DATE_____________
ATTACH YOUR RECEIPT HERE
Replacement Parts List – For Replacement Parts,
call 1-800-237-0987 Only use factory parts to repair this pump.
Ref. Part Number
No. Description
1Power Cord 30019-001
2Float Switch 31039-001
3Shaft Seal 21010-001
4Volute Cover 28104-001
5Impeller 28105-001
6Volute Gasket 19048-001
7Volute Base 28106-001
Address parts correspondence to:
Wayne Home Equipment
100 Production Drive
Harrison, OH 45030 U.S.A.
Please provide following information:
-Model number
-Serial number (if any)
-Part descriptions and number as shown
in parts list
2
3
5
6
7
1
4