resi-linx RL-BV250B User manual

®
WARRANTY
Vcomm Pty Ltd states that the warrant that the customer can rely on is that
provided by the manufacturer. In the event of any warranty claim please
contact us and we will forward it to the manufacturer. The manufacturer will
then determine the extent of their liability. This expressly negates, to the
extent possible by Australian law, any warranty reliance on Vcomm Pty Ltd.
RL-BV240A / RL-BV250B
AV Distribution Range
‘linx-AV’ Quad IR Component Video/Audio Balun Transmitter (1:4)
IR Component Video/Audio Balun Receiver
www.resi-linx.com
ABN: 99 091 281 524
Vcomm Pty Ltd
* Sold separately
A
B
CD E
K
F
G
I
RL-BV250B
J
A RCA Component Video inputs
B Loop Through RCA Comp. Video outputs
C RCA Digital Audio input
and Loop Through output
D IR Emitter output
E IR / Power LED’s
F 12V DC Power input
G Analogue Audio input
H RCA Component Video output
I RCA Digital Audio output
J IR Target input
K Analogue Audio output
H
RL-BV240A
IR
Cable Requirements
4 pair twisted cable
Hardware Connection
1. Ensure all power to equipment is switched off prior to
installation.
RL-BV240A
2. Connect RCA cables from Component source to terminals
A of Transmitter.
3. Connect RCA cable from Digital Audio ouput on
Component source to Digital Audio input C of transmitter
4. Connect audio cable from Analogue Audio output on
Component source to Analogue Audio input G on
transmitter (if required)
5. Connect a second RCA cable from loop through terminals
B of Transmitter to the Component input of the local AV
device (TV, etc).
6. Connect RL-IR700/800* IR emitter to output D of
Transmitter. Place the other end within 25cm of the
IR receiver on the Component source (depending on
environmental conditions).
7. Connect 2 x RJ45 sockets of Transmitter (OUTPUT IA
and OUTPUT IIA) to corresponding INPUT I and INPUT
II Receiver in zone A via 4 pair twisted cable. Repeat for
zones B, C and D. (eg. OUTPUT IB and II B to zone B
INPUT I and II)
RL-BV250B
8. Connect Component Video RCA lead (red, green,
blue) from RCA Video output H of Receiver to the
corresponding input on the component device (TV, etc).
9. Connect Digital Audio RCA lead (orange) from RCA
Digital Audio output I of Receiver to the corresponding
input on the component device (TV, etc).
10. Connect Analogue Audio lead (green) from Analogue
Audio output K of Receiver to corresponding input of
the component device (TV, etc).
11. Connect RL-BV500* IR target to input J of Receiver.
Flat target can be easily mounted (either directly using
adhesive backing, or by using RL-ACC150* Target
Mount) to the desired location, anywhere within the line
of sight of remote controls.
12. Repeat steps 8 - 11 for connection of zones B, C and D.
13. Connect supplied 12V DC switch mode power pack to
power input F on Transmitter.
14. Once installation is complete, switch on power to
all equipment. Check green PWR LE D E on
Transmitter is illuminated.
INSTALLATION MANUAL
OUTPUT II
OUTPUT I
Transmitter Receiver
RJ45 Output RJ45 Input

INSTALLATION MANUAL
WARRANTY
Vcomm Pty Ltd states that the warrant that the customer can rely on is that
provided by the manufacturer. In the event of any warranty claim please
contact us and we will forward it to the manufacturer. The manufacturer will
then determine the extent of their liability. This expressly negates, to the
extent possible by Australian law, any warranty reliance on Vcomm Pty Ltd.
®AV Distribution Range
RL-BV240A / RL-BV250B
‘linx-AV’ Quad IR Component Video/Audio Balun Transmitter (1:4)
IR Component Video/Audio Balun Receiver
www.resi-linx.com
ABN: 99 091 281 524
Vcomm Pty Ltd
RL-BV240A/250B
Power - BV240A 12V DC 500mA Switch Mode
Maximum video input - BV240A 1.2V P-P
Return loss >15dB to 1,000 MHz
Common mode rejection >40dB @ 1,000 MHz
Maximum distance cable Up to 100m
Video Signal Component
Audio Signal Digital / Analogue
Conguration 1:4
IR capability Yes
Loop Through capability Yes
Connections In/Out - BV240A
- BV250B
2 sets - 3 x RCA
8 x RJ45
1 x IR Emitter
1 x Analogue Audio
3 x RCA Video
1 x RCA Audio
2 x RJ45
1 x IR Target
1 x Analogue Audio
Troubleshooting
IR LED indicator on RL-BV240A Transmitter illuminates
briey upon receipt of IR commands.
NOTE: Some brands of TV/Monitors can reduce the
range of the IR Receiver head, which is outside the
scope of the warranty.
Loop Through terminals to
be connected to to local
AV device if required
RL-BV240A
RL-BV250B
Analogue Audio
if required
Connection to zones B, C and D
as above
Remote
Control
RL-BV500
Zone A
Output IIA
Output IA
Pin Conguration
RL-BV240A/250B input 1
1 GR/W
2 GR
3 OR/W
4 BL
5 BL/W
6 OR
7 BR/W
8 BR
+ SOLID POWER
- STRIPED POWER
DIGITAL
AUDIO
VIDEO
Y
VIDEO
Pr / Cr
VIDEO Pb / Cb
VIDEO Pb / Cb
RL-BV240/250 input 2
+ SOLID POWER
- STRIPED POWER
1 GR/W IR / EARTH
2 GR IR / +12V
3 OR/W
4 BL
5 BL/W
6 OR
7 BR/W
8 BR IR / OP
AUDIO
L
AUDIO R
AUDIO R
FOR WEB
ONLY