resi-linx RL-BT100 User manual

RL-BT100
INSTALLATION MANUAL
linx-Audio Bluetooth®Range
Bluetooth In-Ceiling Amplier
www.resi-linx.com
®
Cabling Instructions
Wiring:
1. Run low loss speaker cable from RL-BT100 Amplier
Speaker Terminals F to speakers.
Wiring to another RL-BT100:
2. For connection to another RL-BT100 Amplier run twisted
pair cable from the Output A of the ‘Master’ Amplier unit
(rst in line) to Input B of the ‘Slave’ Amplier unit/s.
Wiring to RL-BT430:
3. For connection to RL-BT430 Input Module run BOTH a
twisted pair cable from Audio Input B and a Figure 8
Power Cable from Power Input E of RL-BT100 Amplier to
RL-BT430 unit.
Hardware Connection
1. Connect speaker cable to Speaker Terminals F . For
optimum performance ensure that speaker polarity is
consistent ie:
- Left Positive output (L+) on RL-BT100 is connected to
the Positive (+) Input on Left speaker
- Left Negative output (L-) on RL-BT100 is connected to
the Negative (-) Input on the Left speaker
- The same wiring must apply to the Right speaker
connections
2. Screw antenna supplied onto Antenna Input D .
3. Drill 16mm hole for mounting of TIM module into plaster
ceiling optimally 750mm distance from left or right speaker
location.
Cable Requirement*:
Audio - Category 5e twisted pair cable
Power - Figure 8 14-020
Speaker - 12-24 AWG Low Loss Speaker Cable
Notes:
1. Recommended cables are run according to TS009
regulations to reduce interference
2. Maximum cable run of twisted pair from Amplier to
RL-BT430 is 40m
3. Maximum cable run of twisted pair cable from RL-BT100
Amplier to second Amplier is 25m
4. RJ45 termination type EIA/TIA 568A wiring standard
*Refer to diagram pg2
WARRANTY
Australian Audio Imports Pty Ltd states that the warrant that the customer can rely on is that provided
by the manufacturer. In the event of any warranty claim please contact us and we will forward it to the
manufacturer. The manufacturer will then determine the extent of their liability. This expressly negates, to
the extent possible by Australian law, any warranty reliance on Australian Audio Imports Pty Ltd. Warranty
will be void if product/s are not installed as per supplied instructions.
Australian Audio Imports Pty Ltd
ABN: 34 005 281
All trademarks and trade names are those of their respective owners. The Bluetooth®
word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by Australian Audio Imports Pty Ltd is under license.
Australian Audio Imports
Balanced
Audio Output
Balanced
Audio Input
IR Target Input
ANT
Mini USB
LED Indicator Input
24V DC
Speaker
8 ohm
linx-Audio
RL-BT100
R+
R-
L-
L+
D
Balanced Audio Output
Balanced Audio Input
IR Target Input
Antenna
Power Input 24V DC
(via Power Supply or RL-BT430/Direct Power Adapter)
Speaker Terminals
Mini USB
LED Indicator Input
C
A
B
A
B
E
F
C
D
G
G
F
E
H
Includes:
RL-BT100 Bluetooth In-Ceiling Amplier
TIM module
Remote Control
Direct Power Adapter
Bluetooth Antenna
Power Supply
Mini USB to USB lead
4. Connect TIM module BLACK cable into LED Indicator Input H
and RED cable into IR Target Input C on RL-BT100 3.5mm
jack (corresponding coloured socket).
5. Place RL-BT100 in ceiling space within easy reach of ceiling
access hole if available (to allow for future accessibility).
Connection to RL-BT430
6. Refer to instruction sheet RL-BT430
Power Connection
7. When cabling to all system components has been completed
and checked, plug power adapter (supplied) into mains and
plug DC jack into Power Input E on RL-BT100.
8. To change power supply to direct power: terminate Figure 8
Power Cable into supplied Direct Power Adapter and connect
to DC Power Input E .
H

RL-BT100
INSTALLATION MANUAL
linx-Audio Bluetooth®Range
Bluetooth In-Ceiling Amplier
www.resi-linx.com
®
resi-linx Audio Wiring Diagram
WARRANTY
Australian Audio Imports Pty Ltd states that the warrant that the customer can rely on is that provided
by the manufacturer. In the event of any warranty claim please contact us and we will forward it to the
manufacturer. The manufacturer will then determine the extent of their liability. This expressly negates, to
the extent possible by Australian law, any warranty reliance on Australian Audio Imports Pty Ltd.
Australian Audio Imports Pty Ltd
ABN: 34 005 281
All trademarks and trade names are those of their respective owners. The Bluetooth®
word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by Australian Audio Imports Pty Ltd is under license.
Australian Audio Imports
* The communication range quoted is calculated based on an unobstructed line of sight test under
optimum conditions. Actual range will vary depending on conditions, and is often less than the maximum
possible. Your actual range will be limited by several factors including, but not limited to, electromagnetic
interference and obstructions.
Troubleshooting
My music is not coming out of the stereo speakers:
• Ensure RL-BT100 settings are set correctly eg. volume level, bass and treble adjustment.
• Ensure the volume on your iPad, iPhone, iPod touch or other Bluetooth enabled device is set to a suitable level.
• Ensure the Bluetooth In-Ceiling Amplier is powered and the power LED on the TIM module is lit to green.
• Ensure the blue LED on your TIM module is ashing slowly indicating your device is connected via Bluetooth technology.
• Ensure all connections are correct and rmly connected to the RL-BT100.
• Ensure your iPad, iPhone, iPod touch or other Bluetooth enabled device is within the 25m* range of the Amplier.
Music Suddenly Stops playing:
• Ensure your Bluetooth device is within the 25m* range of the Amplier.
• RL-BT100 may cut out if Audio overloads to protect the Amplier. Turn off RL-BT100 via remote control and wait 5 seconds for
the system to reset then turn the unit back on and adjust your audio to a more suitable level.
*
EIA/TIA 568A Wiring Standard Pin Wire Colour
1 White w/Green Stripe
2 Green
3 White w/Orange Stripe
4 Blue
5 White w/Blue Stripe
6 Orange
7 White w/Brown Stripe
8 Brown
EIA 568A
This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures
MASTER
RL-BT100
SLAVE
RL-BT100
TIM
Target Indicator
Module
RL-BT430
Input Module for
Bluetooth System

When connected, the blue LED on the Bluetooth In-Ceiling Amplier will ash slowly, returning to a constant blue LED whenever the
connection is lost. Refer to website http://www.resi-linx.com/downloads for separate instructions on how to conveniently rename your
Bluetooth resi-linx device ID to identify different zones eg. kitchen, living, outdoor etc.
NB. When connected adjust Treble, Bass & Level controls on the Bluetooth In-Ceiling Amplier via the remote to your personal preference.
Disconnecting/Changing Connected Device
If you want to switch from your iPad, iPhone, iPod touch or other Bluetooth enabled device to another, follow these steps:
1. Access the Bluetooth settings (as above) and turn the Bluetooth function to ‘OFF’ of the device.
2. The Bluetooth In-Ceiling Amplier can now be connected to a different device.
3. Follow the directions in “Initial pairing to your Bluetooth In-Ceiling Amplier” to connect a different device.
Reconnecting Your Device
If you move out of range** (>25m) or turn off the Bluetooth function on your iPad, iPhone, iPod touch or other Bluetooth enabled
device, the Bluetooth In-Ceiling Amplier will disconnect. To reconnect, simply access the Bluetooth settings on your device, ensuring
Bluetooth function is set to ‘ON’ and select the resi-linx device ID.
** The communication range quoted is calculated based on an unobstructed line of sight test under optimum conditions. Actual range will vary depending on conditions, and is often less than the
maximum possible. Your actual range will be limited by several factors including, but not limited to, electromagnetic interference and obstructions
TIM Module
RL-BT100
USER MANUAL
Initial Pairing to your Bluetooth In-Ceiling Amplier
linx-Audio Bluetooth® Range
Bluetooth In-Ceiling Amplier
www.resi-linx.com
®
Step 1
From your iPad,
iPhone or iPod
touch home page
select ‘Settings’
resi-linx
Step 2
Inside Settings,
select ‘General’
Step 3
Inside General,
select ‘Bluetooth’
Step 4
Turn Bluetooth
‘ON’ and search for
devices. Select the
‘resi-linx’ device ID
* Example provided is to pair to an iPad or iPhone only. Other Bluetooth enabled devices such as your laptop may require a pin code to pair eg. default pin code ‘0000’.
Please refer to equipment user manual for more information.
WARRANTY
Australian Audio Imports Pty Ltd states that the warrant that the customer can rely on is that provided
by the manufacturer. In the event of any warranty claim please contact us and we will forward it to the
manufacturer. The manufacturer will then determine the extent of their liability. This expressly negates, to
the extent possible by Australian law, any warranty reliance on Australian Audio Imports Pty Ltd.
Australian Audio Imports Pty Ltd
ABN: 34 005 281
All trademarks and trade names are those of their respective owners. The Bluetooth®
word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by Australian Audio Imports Pty Ltd is under license.
Australian Audio Imports
D
IR Receiver
Green/Orange
Blue
Red
C
A
B
D
C
A
B
1. Aim Remote (supplied) at IR Receiver for control A . See
Remote Control section for user options.
2. IR Recognition D - indicating TIM is receiving IR
commands
3. Bluetooth indicator C will ash when synced with a
Bluetooth Device
4. Power ON/OFF indicator B will light up when Amplier is
ON
5. When Amplier is muted LED B will turn orange

RL-BT100
linx-Audio Bluetooth® Range
Bluetooth In-Ceiling Amplier
www.resi-linx.com
®
USER MANUAL
OFF
Remote Control
OFF
ON ON
S4
S2S1
MUTE
OFF
ON
OFF
TREBLE BASS BOOST LOCK
AB
C
D
E
F
G
H
I
J
K
S3
Turn On the RL-BT100 by pressing ‘ON’ A
Turn Off the RL-BT100 by pressing ‘OFF’ B
Increase the Volume by pressing ‘Volume Up’ C
Decrease the Volume by pressing ‘Volume Down’ D
Mute Sound by pressing ‘Mute’ E
Adjust the Treble control by pressing ‘Treble’ ‘Up’ F or ‘Down’ G
Adjust the Bass control by pressing ‘Bass’ ‘Up’ H or ‘Down’ I
Turn on ‘Boost’ by pressing ‘On’ J and turn off ‘Boost’ by pressing ‘Off’ K
WARRANTY
Australian Audio Imports Pty Ltd states that the warrant that the customer can rely on is that provided
by the manufacturer. In the event of any warranty claim please contact us and we will forward it to the
manufacturer. The manufacturer will then determine the extent of their liability. This expressly negates, to
the extent possible by Australian law, any warranty reliance on Australian Audio Imports Pty Ltd.
Australian Audio Imports Pty Ltd
ABN: 34 005 281
All trademarks and trade names are those of their respective owners. The Bluetooth®
word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by Australian Audio Imports Pty Ltd is under license.
Australian Audio Imports