Restoration Hardware GRAFTON User manual

INSTALLATION INSTRUCTIONS
MODEL: GRAFTON
RH-5100
RH-5100L
1 REV.B
RH-5100
RH-5100L

Recommended Deck Hole Size 1-3/8” Diameter
Dimensions are in Inches and Approximation of a Typical Installation
2
Restoration Hardware
Faucet Product Size Specification Diagram
Technical support: 1-866-417-5207 Customer Service: 1-877-747-4671 RH-5100 REV. B

Installation Instructions
We Recommend Installation by a Licensed Plumbing Professional
Spout Assembly
Insert SPOUT HOSES (3) and
MOUNTING STUD(6) through
BASE RING (2) and sink hole, (apply
putty or silicone to underside of
RING (2)).
Align SPOUT (1) and secure with
MOUNTING BRACKET(4) and
NUT (5).
Common tools needed:
Adjustable
Wrench Plumbers
Putty
Pipe
Cutter
Assorted
Screwdrivers
Thread
Sealant
3Technical support: 1-866-417-5207 Customer Service: 1-877-747-4671
1
SINK HOLE
5
4
3
2
6
RH-5100 REV. B

Valve Assembly
Place flange NUT (1) and fiber WASHER (2) onto
valve BODY (3).
Insert valve BODY (3) through sink hole from under-
side of sink. Valve BODY (3) should extend 2” above
mounting surface. If necessary adjust lower flange
NUT (1).
Place fiber WASHER (2) and flange NUT (1) onto
upper position of valve BODY (3).
Set valve BODIES (3,3A) so that their outlets are fac-
ing towards the center of the sink and tighten upper
flange NUT (1). 3
4
Hose Assembly
Connect HOSE (8) to outlet of valve BODY (7, 7A).
Hand tighten and secure each COUPLING NUT (8)
with a wrench 1/4 turn.
1
2”
2
3A
7A
8
7
Technical support: 1-866-417-5207 Customer Service: 1-877-747-4671 RH-5100 REV.B

Make Water Supply
Connections
NOTE: SUPPLY RISERS MUST BE PURCHASED
SEPARATELY
Connect water supply to VALVE BODIES(1, 1A) with one of
the three following types of risers:
1/2” IPS FLEXIBLE RISER (2), discard RUBBER
NOSECONE (7), FRICTION WASHER (3) and COUPLING
NUT (4).
3/8” or 1/2” O.D. BULLNOSE RISER (5), place FRICTION
WASHER (3) and COUPLING NUT (4) onto BULLNOSE
RISER (5).
1/2” O.D. COPPER RISER (6), place COUPLING NUT (4),
FRICTION WASHER (3), and RUBBER NOSECONE (7)
onto end of COPPER RISER(6).
Use adjustable wrench to tighten connections. Do not over tight-
en and be careful not to kink copper supply when bending. Use a
tube bender and cutter to properly adjust copper supply.
5
4
3
2
1
6
4
3
7
a
c
b
a.
b.
c.
1A
5Technical support: 1-866-417-5207 Customer Service: 1-877-747-4671 RH-5100 REV B

Install Handles
Turn VALVE STEM (6) to OFF position.
Place ESCUTCHEON (5) onto VALVE STEM (6) and thread BONNET (4) until snug against
ESCUTCHEON (5).
Place HANDLE (3) onto VALVE STEM (6). Check alignment, if necessary reposition handle on stem or
rotate body for proper alignment. DO NOT loosen cartridge stem.
Secure HANDLE (3) into place by tightening SCREW (2).
Place CAP (1) onto HANDLE (3).
1
3
2
4
6
5
6
Technical support: 1-866-417-5207 Customer Service: 1-877-747-4671 RH-5100 REV B
1
3
2
4
5
6

Install Pop- up Drain
Attach POP- UP KNOB (1) onto POP- UP ROD (2)
and insert through hole on SPOUT (3).
Place DRAIN FLANGE (5) with WHITE WASHER (6)
in place through sink drain hole.
Note: putty or silicone may be used instead of
WHITE WASHER (6).
From underside of sink install RUBBER CONE
WASHER (7), FLAT WASHER (8), and FLANGE NUT
(9) onto DRAIN FLANGE (5). Tighten FLANGE NUT (9)
firmly.
Place CLEAR WASHER (10) into DRAIN BODY (11) and
tighten onto DRAIN FLANGE (5) aligning ball rod port to
rear of sink.
Secure BALL ROD (12) into DRAIN BODY (11) with
BALL NUT (13).
Apply thread sealant onto threads of TAILPIECE (17) and
tighten into DRAIN BODY (11).
Secure TAILPIECE ( 17) to TRAP DRAIN (18) .
If necessary trim TAILPIECE (17) for proper fit.
Position STRAP (15) onto POP- UP ROD (2) and
tighten SCREW (16).
Remove one end of CLIP (14) from BALL ROD (12)
by squeezing ends together while sliding.
Insert BALL ROD (12) into lower holes of STRAP (15)
and reassemble CLIP (14).
Place STOPPER (4) into DRAIN FLANGE (5) and by
twisting stopper attach to BALL ROD (12).
Adjust stopper height by repositioning STRAP (15) on
the POP- UP ROD (2) and tightening SCREW (16).
Test Installed Faucet
With handles in OFF position, turn on water supplies and
check all connections for leaks.
Remove AERATOR (19) from SPOUT (3) and operate
both handles to flush water lines thoroughly.
Reattach AERATOR (19) to SPOUT (3) after flushing
lines.
Operate pop-up drain assembly and check for leaks.
7
6
15
16
5
1
98
3
2
10
11
12 13
17
18
Sink hole
14
4
19
7Technical support: 1-866-417-5207 Customer Service: 1-877-747-4671 RH-5100 REV B

Care and Cleaning
The lustrous finish on your Restoration Hardware Bathware fixture should
be treated with care. Improper handling or cleaning can damage the surface
of any metal finish. Use a soft cloth to wipe clean. Avoid harsh abrasive
cleaner. Water contains lime and other mineral deposits that will be left on
the surface after the water has evaporated. You can prevent these deposits
from forming by always wiping the fixture dry immediately after use.
Technical Support and Customer Service
For technical support in the installation of your Restoration Hardware
Bathware fixture, please call 1-866-417-5207 weekdays between the hours
of 7:00am and 4:00pm PST.
For other questions regarding your order, to order additional components of
the Restoration Hardware Bathware Collection, to order replacement parts,
or to address warranty issues, please contact Restoration Hardware
Customer Service at 1-877-747-4671.
8 RH-5100 REV BEN-2882