DXV Percy D35105500 User manual

- 1 -
INSTALLATION INSTRUCTIONS
Percy™Pressure Balanced
Shower Valve Trim Kit
SAVE FOR FUTURE USE
ROUGHING-IN DIMENSIONS:
• For reference
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2013 M965527 Rev. 1.6
In the United States:
DXV by American Standard
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV by American Standard
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV by American Standard
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Cylinder Handle
Model D35105500
To be used with D35000500.191
Pressure Balanced Shower Valve
Cross Handle
Model D35105540
Phillips Screwdriver Regular Screwdriver
THREADED INLETS (STOPS)
INLETS
1/2" NPT
1/2" NPT PLUG
3-3/8"
(86mm)
FINISHED WALL
BOTTOM OF
SHOWER OR TUB
48" to 54"
(1219 to 1372mm)
OPTIONAL
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
72'' to 84''
(1828 to 2133mm)
"SEE
ILLUSTRATION"
3" TO 4"
(76 TO 102mm)
1/2" (13mm) I.P.S.
7-5/16" D.
(213mm)
1-5/8" TO 3-1/4"
(41mm TO 83mm)
5-7/8"
(149mm)
OUTLETS
1/2"
(13mm)
NPT
CY
HANDLE
CROSS
HANDLE
RECOMMENDED TOOLS AND MATERIALS
Thank you for selecting DXV by American Standard. To ensure that your
installation proceeds smoothly, please read these instructions carefully
before you begin.
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing,
supply stores. It is essential that the tools and materials be on hand before work is begun.

- 2 - M965527 Rev. 1.6
1
1a 1b
Turn off water at main supply.
CAUTION
INSTALL VALVE TRIM
• Figure 1. When nished tiling the wall, remove PLASTER GUARD (1).
• Push CARTRIDGE CAP (2) over VALVE CARTRIDGE until
seated against stop.
• Install ATTACHMENT SCREW (3) and tighten to secure
CARTRIDGE CAP (2) to valve.
• Figure 2. Align mounting holes and install ESCUTCHEON
HOLDER (4) with gasket onto CARTRIDGE CAP (2).
Mount ESCUTCHEON SUPPORT (5) to ESCUTCHEON
HOLDER (4) with four SCREWS (6).
• Figure 3. Push ESCUTCHEON (7) onto CARTRIDGE
CAP (2) tight against nished wall.
• Align mounting holes and install the two
MOUNTING SCREWS (8) and tighten.
Figure 3.
7
2
8
Figure 1.
VALVE CARTRIDGE
1
23
GASKET
MOUNTING
HOLES
Figure 2.
4
5
6
2
VALVE
MOUNTING
HOLES
INSTALL HANDLE
• Push DIAL PLATE (1) onto CAP (2) until ush against ESCUTCHEON (3).
• Align HANDLE (4, 4a) and thread the HANDLE BASE (5) onto the HANDLE SUPPORT (6). Hand tighten.
1
4
5
2
6
3
5
4a
2

- 3 - M965527 Rev. 1.6
By restricting HANDLE rotation and limiting the amount of hot water allowed to mix with the cold, the
HOT LIMIT SAFETY STOP (1) reduces risk of accidental scalding. To set the maximum hot water
temperature of your faucet, all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP (1).
• Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before making adjustment to HOT
LIMIT STOP (1). Use a at blade screwdriver to pry free the HOT LIMIT SAFETY STOP (1). Pull
forward and rotate counterclockwise one number to limit hot water temperature.
Use ARROW (3) on CARTRIDGE (4) and NUMBERS (5) on HOT LIMIT STOP (1)
for indication.
1
5
1
3
1
1
9
7
5
3
1
0
1
5
1
3
1
1
9
7
5
3
1
1
5
1
3
1
1
9
7
5
3
1
COLDER
(Larger Numbers)
0 1 3 5 7 9 11 13 15
HOTTER
(Smaller Numbers)
0 1 3 5 7 9 11 13 15
1
5
1
5
44
3
3
22
ADJUST HOT LIMIT STOP (MUST BE DONE PRIOR TO TRIM INSTALLATION)
3
BACK TO BACK INSTALLATION
(SEE ILLUSTRATION STEP 6 FOR REFERENCE) TEST INSTALLED FAUCET
• Remove Handle and Trim from Valve.
See step 3 for reference.
• Remove PRESSURE BALANCE UNIT (5). Rotate
PRESSURE BALANCE UNIT (5) 180˚ so that the inlets
face up and the large outlet port faces down.
• Push PRESSURE BALANCE UNIT (5) in casting make
sure inlets line up with holes in bottom of casting. Top
ange should butt up against top of casting.
• Reassemble FIXATION RING (4) and CARTRIDGE (1).
• Turn VALVE "off".
• With HANDLE in "off" position, turn on water supplies
and check all connections for leaks.
• Operate HANDLE and ush water lines thoroughly.
• Check all connections for leaks.
4 5
• Remove Handle and Trim from Valve. See step 3 for reference.
• Shut off water supply by either closing off main water supply, or closing off the hot and cold CHECK STOPS
on valve, if present.
TO GAIN ACCESS TO VALVE FOR SERVICING
• Remove CARTRIDGE (1) by removing CARTRIDGE SCREWS (2). Remove three SCREWS (3) from FIXATION RING (4) and
pull out PRESSURE BALANCING (5) unit.
• Clean SEALS (9) on base of CARTRIDGE (1). Check base of PRESSURE BALANCING UNIT (5) and clean O-RINGS (6).
Remove CAPS (7) and check O-RINGS on inside of CAPS (7). Clean inside sealing surfaces of VALVE BODY (8).
• Re-assemble PRESSURE BALANCING UNIT (5) and CARTRIDGE (1). Tighten all screws. Turn on water supply and see
above for installing TRIM and HANDLE.
VALVE LEAKS WHEN SHUT OFF
• Remove PRESSURE BALANCE UNIT (5). Remove CAPS (7) and clean valve thoroughly.
• Examine balancing unit and check condition of O-ring on end of piston. Piston should move back and forth. Order Repair
Part M952100-0070 if balancing unit is defective.
• Replace CAPS (7) and install PRESSURE BALANCE UNIT (5). Make sure inlets line up with two holes in bottom of casting.
Top ange should butt-up against top of casting.
UNABLE TO MAINTAIN CONSTANT TEMPERATURE
BACK TO BACK INSTALLATION
ROTATE 180˚
1
2
9
5
5
7
8
6
4
3
INLETS
LARGE OUTLET
6

- 4 - M965527 Rev. 1.6
Pressure Balanced
Shower Valve Trim Kit
Percy™
100
144
Replace the "YYY" or "XXX" with
appropriate nish code
POLISHED CHROME
BRUSHED NICKEL
MODEL NUMBERS
D35105540
D35105500
Cylinder Handle
Cross Handle
M964654-0070A
TRIM PLATE HOLDER
M964656-YYY0A
TRIM PLATE
WITH SCREWS
HOT
COLD
OFF
M964749-YYY0A
HANDLE BASE
M964697 -YYY0A
CROSS
HANDLE KIT
M964610-YYY0A
CYLINDER
HANDLE KIT
H961229.XXX
TRIM RING
H960685.XXX
ESCUTCHEON SCREWS
A3195.191
EXTENSION KIT
(CARTRIDGE)
A3196.191
EXTENSION KIT
(DIVERTER)