RF Elements STATION BOX S Operational manual

www.rfelements.com
Outdoor Case for RouterBoard RB711 and RB411
Product Datasheet
StationBox® S turns your RouterBoard RB711 or
RB411 into flexible radio unit. Snap It to the
RF elements MiMo Sector Antenna or compatible
holder for easy installation.
STATIONBOX® S PARTS – EMBEDDED SOLUTION/OEM
COMPATIBLE PIGTAILS
SMA-RP with O-ring to MMCX, RSMAMMCX
SMA-RP with O-ring to U.FL (IPAX), RSMAUFL
N-female with O-ring to MMCX, RNFMMCX
N-female with O-ring to U.FL (IPAX), RNFUFL
OTHER FEATURES
TECHNICAL DATA
Weight
0.33 kg / 0.7 lbs – single piece incl. package
7 kg / 15.5 lbs – per Carton Box, 20 pcs
Material
ABS plastic
(UV stabilized & weather resistant)
Single Piece
210 × 55 × 140 mm
8.3 × 2.2 × 5.5 inches
Carton (20pcs)
220 × 550 × 280 mm
8.7 × 21.7 × 11 inches
SUPPORTED PCBS
MikroTik
RouterBoard
RB711 Series
RB411 Series /not compatible with „U“
version with longer form factor/
COMPATIBLE RF ELEMENTS ACCESSORIES
PoE adapter, 24V1A, DC grounded, POE24V1AEU
PoE adapter, 24V1A, DC grounded, POE24V1AUS
---
Omni Antenna 5GHz/5dBi,Product ID: OARDSBX55
Omni Antenna v2.4GHz/4dBi, Product ID: OARDSBX244
Omni Antenna 800-900MHz/1dBi, Product ID: OARDSBX800
---
EasyBracket S, Pole and Wall Mount for StationBox® S and
StationBox® Mikro, Product ID: EBS001

Instruction Manual StationBox® S
Package Contains:
A Install the SMA pigtails using special
washer, nut and o-ring.
B When installing N-connectors, expand
the openings using cutter.
C Use Plastic Caps to cover the top
openings when not used for pigtail
installation. Secure Caps with
2.9×6.5mm (the smallest) screws
and washers.
1. Body
2. Top Cover
3. Bottom Cover
4. Seal
5. Light Guides
6. Plastic Caps
7. Screws 2.9×25mm (2×)
8. Screws 2.9×12mm (2×)
9. Screws 2.9×6.5mm (6×)
10. Washers (2×)
2 Installation of RouterBoard
A Install the RouterBoard using
2.9×6.5mm (the smallest) screws.
B Connect the pigtails to the RouterBoard.
1
2
3
4
789
10
5
6
1 Installation of Pigtails
www.rfelements.com RouterBoard is Trademark of MikroTik, Aizkraukles iela 23, Riga, LV-1006 LATVIA

Install the Top Cover using screws 2.9×25mm and screws 2.9×12mm.
Mind the correct positioning of the Screws as shown on picture!
Cut or chip away premolded parts of the front panel, if interfering with
RouterBoard´s connectors.
3 Installation of the Seal and Light Guides
A Install the Silicone Seal in StationBox´s Body.
B According to the specic RouterBoard setup, install the Light Guides
to support readability of RouterBoard LEDs.
Instruction Manual StationBox® S
5 How to Mount, Remove and Protect the StationBox® S
RF elements Accessories
4 Install the Top Cover
You can easily snap StationBox® S to compatible Antenna. Please
refer to our webpage www.rfelements.com to check updated list of
compatible antennas.
To remove StationBox® S from the mount, use tool to release the
mount´s lock. Any rm object that ts the gap could be used:
screwdriver, wrench, knife etc.
For installation on the Wall or Pole, use RF elements EasyBracket™ S,
bracket compatible with StationBox® S and StationBox® Mikro.
2× Screws #7
2× Screws #8
www.rfelements.com RouterBoard is Trademark of MikroTik, Aizkraukles iela 23, Riga, LV-1006 LATVIA