RIAN SATSPEEDBOX III R7920 User manual

Informationstechnologie-Lösungen
SATSPEEDBOX III R7920
User Manual
Gigabit Ethernet IAD 11n

SATSPEEDBOX III R7920 Manual Page 2
Table Content
Prefaces ............................................................................................................... 4
About This Manual ........................................................................................... 4
Copyright Declarations .................................................................................... 4
Trademarks ..................................................................................................... 4
Safety Instructions .......................................................................................... 4
Audience.......................................................................................................... 4
Introduction.......................................................................................................... 5
Overview ......................................................................................................... 5
Introduction .................................................................................................... 6
Front Panel LED Indicators & Rear Panels SATSPEEDBOX III R7920 ............... 6
Introduction.......................................................................................................... 7
Package Content .............................................................................................. 7
Hardware Installation...................................................................................... 8
Port Description: Model SATSPEEDBOX III R7920 ................................................ 8
Quick Start....................................................................................................... 9
Installation: .................................................................................................... 9
Connecting to a PC: ......................................................................................... 9
How to configure SATSPEEDBOX III R7920? ........................................................ 9
How to use VoIP?............................................................................................. 9
Wizard Setup ................................................................................................. 10
Step 1. Connection wizard................................................................................10
Step 2. Welcome to the Connection Wizard ........................................................10
Step 3. Time Zone Setup .................................................................................11
Step 4. LAN Port Type Setup: ...........................................................................11
Step 5. WAN Port Type Setup:..........................................................................11
Step 6. Wireless Interface Setting .....................................................................13
Step 7. Voip Setup ..........................................................................................14
VOIP Setup..........................................................................................................15
WAN Interface ............................................................................................... 15
Broadband .....................................................................................................18
LAN Interface ................................................................................................ 19
Client List ......................................................................................................19
DDNS ............................................................................................................. 20
QoS................................................................................................................ 21
Wireless......................................................................................................... 21
Advanced Setting............................................................................................22
Security.........................................................................................................23
Key Length: ...................................................................................................24
Access Control ................................................................................................25
WDS .............................................................................................................25
Site Survey ....................................................................................................26
WPS ..............................................................................................................26
SIP Setting and “Emergency Routine” .....................................................................27
SIP Setting.....................................................................................................28
Sip Advance setting.........................................................................................29
Codec Setting.................................................................................................33
ToS ...............................................................................................................34
Telephone ...................................................................................................... 35
Common........................................................................................................35
Analog Phone .................................................................................................36
Region...........................................................................................................39
Phone Book.................................................................................................... 40
Speed Dial .....................................................................................................40
Dial Plan With URL ..........................................................................................41
Security ..............................................................................................................42

SATSPEEDBOX III R7920 Manual Page 3
Firewall.......................................................................................................... 42
IP Filtering .....................................................................................................42
Mac Filtering...................................................................................................43
URL Filtering ..................................................................................................43
Port Filtering ..................................................................................................44
Port Forwarding ..............................................................................................44
DMZ ..............................................................................................................45
Maintenance ........................................................................................................46
System........................................................................................................... 46
Account Setting ..............................................................................................46
Time Setting ..................................................................................................46
Tools.............................................................................................................. 47
Configuration .................................................................................................47
Upgrade Firmware...........................................................................................47
Ping Test .......................................................................................................48
Restart ..........................................................................................................48
Logout ........................................................................................................... 49
Auto Provision / TR069 ................................................................................. 49
HTTP / FTP .....................................................................................................49
TR069 ...........................................................................................................50
Information .........................................................................................................51
System Status................................................................................................ 51
USB ACCESS........................................................................................................52
File server...................................................................................................... 52
Permanent file access ......................................................................................53
Printer server ................................................................................................ 54
Installation steps: ...........................................................................................54
Appendix .............................................................................................................56
A - FAQ List.................................................................................................... 56
B - Scenario Application:................................................................................ 57
Glossary ..............................................................................................................58
Certifications........................................................................................................64
CE / FCC / RoHS ............................................................................................ 64
FCC...............................................................................................................64
FCC Class B Notice ..........................................................................................64
IC Statement..................................................................................................64
EC Declaration of Conformity ......................................................................... 64
WEEE –B2C ........................................................................................................65
Candle Flame .......................................................................................................66
Warning for users ...........................................................................................66

SATSPEEDBOX III R7920 Manual Page 4
Prefaces
About This Manual
This manual is designed to assist users in using SATSPEEDBOX III R7920 Gigabit
Ethernet IAD. Information in this document has been carefully checked for accuracy;
however, no guarantee is given as to the correctness of the contents. The
information contained in this document is subject to change without notice.
Copyright Declarations
Trademarks
Products and Corporate names appearing in this manual may or not be registered
trademarks or copyrights of their respective companies, and are used only for
identification or explanation and to the owners’ benefit, without to infringe.
Safety Instructions
The most careful attention has been devoted to quality standards in the manufacture
of the SATSPEEDBOX III R7920 Gigabit Ethernet IAD. Safety is a major factor in the
design of every set. But, safety is your responsibility too.
Use only the required power voltage. Power Input: AC 110V/220V, 50-60Hz
To reduce the risk of electric shock, do not disassemble this product. Opening
or removing covers may expose the SATSPEEDBOX III R7920 to hazardous
voltages. Incorrect reassembly can cause electric shock when this product is
subsequently used.
Never push objects of any kind into the equipment through housing slots
since they may touch hazardous voltage points or short out parts those could
result in a risk of electric shock. Never spill liquid of any kind on the product.
If liquid is spilled, please refer to the proper service personnel.
Use only Unshielded Twisted Pair (UTP) Category 5 Ethernet cable to RJ-45
port of the SATSPEEDBOX III R7920 Gigabit Ethernet IAD.
Audience
This document is intended for system vendor who are using SATSPEEDBOX III R7920
to build an Internet telephony gateway or server application. It is assumed that the
reader has the general knowledge of VoIP applications and products.
Copyright 2012. All rights reserved. This publication contains information that is
protected by copyright. No part may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language without written
permission from the copyright holders.

SATSPEEDBOX III R7920 Manual Page 5
Introduction
This document describes the usage of SATSPEEDBOX III R7920.
Overview
SATSPEEDBOX III R7920 is a device that allows several PC or IPTV Set-Top
Boxes to connect and to browse the Internet.
SATSPEEDBOX III R7920 provides two RJ11 analog interfaces for VoIP calls,
PBX, fax machines or any analog telephone.

SATSPEEDBOX III R7920 Manual Page 6
Introduction
The SATSPEEDBOX III R7920 Ethernet Gigabit IAD 11n provides a total solution
for integrating voice-data network and PSTN.
The SATSPEEDBOX III R7920 Ethernet Gigabit IAD 11n supports SIP VoIP
Protocol.
The SATSPEEDBOX III R7920 Ethernet Gigabit IAD 11n allows 1~2 lines
analog voice and fax communication over a traditional data
communications/data networking digital Internet.
Model
PSTN Port
FXS
Port
WAN
Port
LAN Port
RJ-11 port
USB
SIP
SATSPEE
DBOX III
R7920
0
2
1
4
2
1

Front Panel LED Indicators & Rear Panels
SATSPEEDBOX III R7920
LED
State
Description
POWER
On
Off
Device is powered on
Device is powered off
WAN
On
Flashing
Off
Network connection established
Data traffic over WAN interface
Waiting for network connection
LAN1 –LAN4
On
Flashing
Off
LAN is connected successfully
Data is transmitting
No connected Ethernet device
Wi-Fi
On
Flashing
Off
Wireless network connection available
Data traffic over WLAN interface
Wireless network connection disabled
REG
On
Off
Successful registered on VoIP Account
Not registered on VoIP Account
PHONE1
PHONE2
On
Flashing
Off
Telephone set is On-Hook
Phone is ringing
Telephone set is Off-Hock
USB
On
Off
No USB device connected
USB device connected
------------------------------------------------------------------------------------

SATSPEEDBOX III R7920 Manual Page 7
Introduction
Package Content
Please check enclosed product and its accessories before installation. These contents
may differ slightly depending on your product version.
SATSPEEDBOX III R7920 Ethernet Cable Phone Cable
Power Adapter

SATSPEEDBOX III R7920 Manual Page 8
Hardware Installation
Port Description: Model SATSPEEDBOX III R7920
Port
Description
POWER
Power connector for 12V/1.5A power adapter
PHONE1
PHONE 2
Phone ports are made to connect analog phones for
VoIP
USB
USB interface for SAMBA, Printers and 3G stick
LAN(Local Area
Network)
Connect to PC with Ethernet cable. 1 port allows your
PC or Switch/Hub to be connected to the device
through a networking cable with RJ-45 connectors
used on 10BaseT and 100BaseTX networks.
WAN(Wide Area
Network)
Connect to the network with an Ethernet cable. This
port allows your device to be connected to an
Internet Access device, e.g. router, cable modem,
ADSL modem, through a networking cable with RJ-45
connectors used on 10BaseT and 100BaseTX
networks.
RES(Reset button)
Push this button until 3 seconds, and device will be
set to factory default configuration.

SATSPEEDBOX III R7920 Manual Page 9
Quick Start
Installation:
1. Connect the 12V DC IN to the power outlet with power adaptor.
2. Connect blue WAN port with the Ethernet cable to a WAN network.
3. Connect your existing analog phones to the PHONE1 and PHONE2 ports
Connecting to a PC:
4. Connect the Ethernet cable (with RJ-45 connector) to any LAN port.
5. Connect the other end of the Ethernet cable to your PC’s installed network
interface card (NIC).
How to configure SATSPEEDBOX III R7920?
1. Configure your PC or NB to the same subnet with SATSPEEDBOX III R7920.
2. Use web browser (IE/Firefox) link to url: http://192.168.1.1 (If you connect
to LAN port, link to url: http://192.168.1.1 )
3. Login user name: admin
4. Login password: admin
5. Use this web configuration interface to configure all system functionality;
firstly you should change the WAN network environment to yours.
How to use VoIP?
1. Configure SIP user account to register your SIP proxy, use web configuration:
“SIP Settings” -> “Account Setting”
a. Port Phone Number
b. Port Authentication User Name
c. Port Authentication Password
d. Confirmed Password
2. Configure SIP registrar server and proxy server, use web configuration:
“SIP Settings” -> “Server Setting”
a. Registrar Server Address
b. Outbound Proxy Address
3. Make sure SATSPEEDBOX III R7920 has already registered to your proxy, and
then you can make a call

SATSPEEDBOX III R7920 Manual Page 10
Wizard Setup
Wizard for Quick Setup SATSPEEDBOX III R7920 after finishing the authentication,
the Main menu will display 2 parts of configuration, please click “Connection wizard”
to enter quick start:
Pleas connect to the GUI (graphical user interface) with a web browser and following
login information:
IP Address: http://192.168.1.1
Login user name: admin
Login password: admin
Step 1. Connection wizard
Step 2. Welcome to the Connection Wizard

SATSPEEDBOX III R7920 Manual Page 11
Step 3. Time Zone Setup
Time Zone Select : Choose your time zone
NTP Server : Select NTP server.
Step 4. LAN Port Type Setup:
Step 5. WAN Port Type Setup:
For most users, Internet access is the primary application. The SATSPEEDBOX III
R7920 supports the WAN interface for Internet access and remote access. The
following sections will explain more details of WAN Port Internet access and
broadband access setup. When you click “WAN Port Type Setup” of the Wizard
Setup, the following setup page will be show.
Three methods are available for Internet Access:
Fixed IP User: If you are a leased line user with a fixed IP address, fill out
the following items with the information provided by your ISP.

SATSPEEDBOX III R7920 Manual Page 12
WAN IP Address: check with your ISP provider
Subnet mask: check with your ISP provider
Default Gateway: check with your ISP provider
DHCP Client (Dynamic IP):
Get WAN IP Address automatically
ADSL Dial-Up User (PPPoE Enable)
Some ISPs provide DSL-based service and use PPPoE to establish communication link
with end-users. If you are connected to the Internet through a DSL line, check with
your ISP to see if they use PPPoE. If they do, you need to select this item.
PPPoE User Name: Enter User Name provided by
your ISP
PPPoE Password: Enter Password provided by your
ISP.
Confirmation Password: Enter Password to confirm again.

SATSPEEDBOX III R7920 Manual Page 13
Step 6. Wireless Interface Setting
Disable Wireless LAN Interface: Select to disable wireless function.
Band: Select a proper wireless mode. The Router communicates with
standard 802.11b, standard 802.11g , standard 802.11n, both 802.11b and
802.11g simultaneously, both 802.11g and 802.11n simultaneously, or three
type simultaneously.

Mode: select wireless mode, there are 3 wireless modes, default is AP mode
SSID: The identification of the wireless LAN. SSID can be any text numbers or
various special characters. The default SSID is "sboxIII". We suggest you to
change it.
Channel Width: select the frequency band used to transmit the data, 20MHz
or 40MHz channel width
Channel Number: The channel of frequency of the wireless LAN. The default
channel is 11. You may switch channel if the selected channel is under serious
interference.
Broadcast SSID: select enable or disable broadcast SSID. Disable broadcast
SSID, the user may only see the information except SSID or just cannot see
any information about wireless router while doing site survey.
Data Rate: select wireless Data Transfer Rate, default is Auto
Associated Clients: click “show active client”button to see the current status
for wireless clients

SATSPEEDBOX III R7920 Manual Page 14
Step 7. Voip Setup
SIP Number: you need to input the User Name get from your ISP.
SIP Server address: you need to input the Proxy add get from your ISP.
SIP Server Domain: you need to input the SIP Domain get from your ISP.
User Name: you need to input the Register User Name get from your ISP.
Password: you need to input the Register Password get from your ISP.

SATSPEEDBOX III R7920 Manual Page 15
VOIP Setup
WAN Interface
WAN (Wide Area Network) is a network connection connecting one or more LANs
together over some distance. For example, the means of connecting two office
buildings separated by several kilometers would be referred to as a WAN connection.
The size of a WAN and the number of distinct LANs connected to a WAN is not limited
by any definition. Therefore, the Internet may be called a WAN.
WAN Settings are settings that are used to connect to your ISP (Internet Service
Provider). The WAN settings are provided to you by your ISP and often times
referred to as "public settings". Please select the appropriate option for your specific
ISP.
For most users, Internet access is the primary application. SATSPEEDBOX III R7920
supports the WAN interface for internet access and remote access. The following
sections will explain more details of WAN Port Internet access and broadband access
setup. When you click “Internet Setting”, the following setup page will be shown.
Three methods are available for Internet Access.
Static IP
If you are a leased line user with a fixed IP address, enter in the IP address, subnet
mask, gateway address, and DNS (domain name server) addresses provided to you
by your ISP. Each IP address entered in the fields must be in the appropriate IP
form, which are four IP octets separated by a dot (x.x.x.x). The Router will not
accept the IP address using other format.
Example: 168.95.1.1

SATSPEEDBOX III R7920 Manual Page 16
IP Address: Check with your ISP provider.
Subnet Mask: Check with your ISP provider.
Default Gateway: Check with your ISP provider.
MTU size: MTU stands for Maximum Transmission Unit, the largest physical
packet size, measured in bytes that a network can transmit. Any messages
larger than the MTU are divided into smaller packets before being sent.
The key is to be deciding how big your bandwidth pipe is and select the best
MTU for your configuration. For example, you have a 33.6 modem, you use a
MTU of 576, and if you have a larger pipe you may want to try 1500.
Enable UPnP (Universal Plug and Play): A protocol let network connected
devices install and configure easily. For NAT routers, the major feature of
UPnP on the router is “NAT Traversal”. When enable the function, the ports
under the firewall will be opened automatically, and the device can pass
through a router.
Enable IGMP Proxy: The IGMP proxy can act as a multicast proxy for hosts on
LAN sides. When you enable the function, you can access the multicast group
whenever you want.
DHCP client
Dynamic Host Configuration Protocol (DHCP), Dynamic IP (Get WAN IP Address
automatically). If you are connected to the Internet through a Cable modem line,
then a dynamic IP will be assigned.
Note: WAN port gets the IP Address, Subnet Mask and default gateway IP address
automatically, if DHCP client is successful.

SATSPEEDBOX III R7920 Manual Page 17
DHCP Vendor Class ID: The Dynamic Host Configuration Protocol (DHCP) is a
network configuration protocol for hosts on Internet Protocol (IP) networks
PPPoE
Point-to-Point Protocol over Ethernet (PPPoE). Some ISPs provide DSL-based
services and use PPPoE to establish communication link with end-users. If you are
connected to the Internet through a DSL line, check with your ISP to see if they use
PPPoE. If they do, you need to make sure the following items, PPPoE User name:
Enter username provided by your ISP. PPPoE Password: Enter password provided by
your ISP.

SATSPEEDBOX III R7920 Manual Page 18
Broadband
In this page you can create multi wan interface, max for 4 connections, and VLAN TAG is must.
SAT Optimization
In this page you can select if you want to use internet through satspeed Gateway “compressed” &
optimized or not, or only
optimized, or complete
without any
optimization.

SATSPEEDBOX III R7920 Manual Page 19
LAN Interface
The IP settings of the LAN (Local Area Network) interface for the device. These
settings may be referred to as "private settings". You may change the LAN IP
address if needed. The LAN IP address is private to your internal network and cannot
be seen on the Internet. The default IP address is 192.168.1.1 with a subnet mask of
255.255.255.0.
LAN is a network of computers or other devices that are in relatively close range of
each other. For example, devices in a house or office building would be considered
part of a local area network.
LAN IP Address: Assign the IP address of LAN server, default is 192.168.1.1
Subnet Mask: Select a subnet mask from the pull-down menu, default is
255.255.255.0.
DHCP Server Setting: DHCP stands for Dynamic Host Control Protocol. The
DHCP server gives out IP addresses when a device is starting up and request
an IP address to be logged on to the network. The device must be set as a
DHCP client to "Obtain the IP address automatically". By default, the DHCP
Server is enabled in the unit. The DHCP address pool contains the range of
the IP address that will automatically be assigned to the clients on the
network.
When you enable the DHCP server, DHCP Client Range: Enter the starting IP
address for the DHCP server’s IP assignment and the ending IP address for
the DHCP server’s IP assignment.
Client List

SATSPEEDBOX III R7920 Manual Page 20
DDNS
Dynamic DNS is a service that provides you with a valid, unchanging, internet
domain name (an URL) to go with that (possibly ever changing) IP-address.
The DDNS (Dynamic DNS) service allows you to alias a dynamic IP address to a
static hostname, allowing your computer to be more easily accessed from various
locations on the Internet.
Without DDNS, the users should use the WAN IP to reach internal server. It is
inconvenient for the users if this IP is dynamic. With DDNS supported, you apply a
DNS name for your server (e.g., Web server) from a DDNS server. The outside users
can always access the web server using the www.ata.com regardless of the WAN IP.
When you want your internal server to be accessed by using DNS name rather than
using the dynamic IP address, you can use the DDNS service. The DDNS server
allows to alias a dynamic IP address to a static hostname.
Unlike DNS that only works with static IP addresses, DDNS works with dynamic IP
addresses, such as those assigned by an ISP or other DHCP server. DDNS is popular
with home networkers, who typically receive dynamic, frequently-changing IP
addresses from their service provider.
DDNS is a method of keeping a domain name linked to a changing (dynamic) IP
address. With most Cable and DSL connections, you are assigned a dynamic IP
address and that address is used only for the duration of that specific connection.
With the SATSPEEDBOX III R7920, you can setup your DDNS service and the device
will automatically update your DDNS server every time it receives a different IP
address.
Enable DDNS: Enable/Disable the DDNS service, default setting is Disable.
DDNS Server Type: Support three types of DDNS, DynDns.org or TZO.net or
No-IP.
Domain Name: The domain which you register in DynDns.org or TZO.net or
No-IP website.
DDNS Username: The username which you register in DynDns.org or TZO.net
or No-IP website.
DDNS Password: The password which you register in DynDns.org or TZO.net
or No-IP website.