RIAREX EVC-DG-DC354A User manual

Installation and Operating Instructions
Mini Vandalproof dome camera
EVC-DG-DC354A / EVC-TG-DV354A

1. Safety Instructions
• Read these safety instructions and the operation manual first before you install and commission
the camera.
• Keep the manual in a safe place for later reference.
• Protect your camera from contamination with water and humidity to prevent it from permanent
damage. Never switch the camera on when it gets wet. Have it checked at an authorized service
center in this case.
• Never operate the camera outside of the specifications as this may prevent the camera
functioning.
• Do not operate the cameras beyond their specified temperature, humidity or power ratings.
• Operate the camera only at a temperature range of -10°C to +50°C and at a humidity of
max. 90%.
• To disconnect the power cord of the unit, pull it out by the plug. Never pull the cord itself.
• Pay attention when laying the connection cable and observe that the cable is not subject
to heavy loads, kinks, or damage and no moisture can get in.
• Do not attempt to disassemble the camera board from the dome.
• The warranty becomes void if repairs are undertaken by unauthorized persons.
Do not open the camera housing.
• Never point the camera towards the sun with the aperture open. This can destroy the sensor.
• Installation, maintenance and repair have to be carried out only by authorized service centers.
• Before opening the cover, disconnect the unit from mains input.
• The fitter is responsible for the system of protection being followed in accordance with the
technical data, e.g. by sealing of the cable outlet with silicone.
• All openings provided in the housing for assembly purposes must be closed and/or sealed.
• Contact your local dealer in case of malfunction.
• Do not use strong or abrasive detergents when cleaning the dome. Use a dry cloth to clean he
dome surface. In case the dirt is hard to remove, use a mild detergent and wipe gently.
• During assembly, care must be taken to ensure that existing seals are correctly inserted
and are not displaced as a result of assembly.
Damaged seals must not be used.
NOTE: This is a class A digital device. This digital device can cause harmful interference in
a residential area; In this case the user may be required to take appropriate corrective
action at his/her own expense.

2. General Description
• For Wall and In-ceiling Mount (FW versions) or Ceiling Surface Mount(SW versions)
• Vandal Resistant
• 1/3” Color/B&W Board Camera with Super HAD CCD
• Resolution of 540 Horizontal Lines
• True DAY-NIGHT by ICR (D versions only)
• High Speed Shutter (ESC)
• Digital Signal Processing (DSP)
• Backlight compensation (BLC)
• Automatic White Balance (ATW)
• White Aluminum Die-cast Casing
• Clear Lexan Bubble, 57mm
• For Easy Indoor and Outdoor Installation (IP66)
Supplied Items
1x Colour dome camera
3x Installation screws
1x Connecting cable (Video and power)
1x Template for flush mount
1x Wrench for surface mount
1x Installation and Operating Instructions
3. Parts Name
Make sure that this arrow indicates

Camera image direction.
3.1 Power and Video Connection
3.2 Surface Mount
1. Fix the base housing to the desired place with screws supplied.
2. Adjust desired scene by turning and moving the camera bracket and fix it
with stopper ring by turning it by hand.
3. Put the dome cover over the base housing and turn it clockwise by hand.
4. To fix dome cover tight, use set screw.
Video out
Power (+) GND
GND
Black: Power input
White: Video output

3.3 Flush Mount
1) Use template processing sticker on the desired place to install camera and make a hole
on that place.
2) Place the base housing on the hole and fix it with screws supplied.
3) Adjust desired scene by turning and moving the camera bracket and fix it with stopper ring
by turning it by hand.
4) Put the dome cover over the base housing and turn it clockwise by hand.

4. Specifications
Type Flush Mount type Surface Mount type
EVC-DG-DC354A EVC-TG-DV354A
Image Sensor 1/3” CCD, Sony Super HAD II Interline Transfer CCD
Video standard PAL, Colour, black/white
Active picture elements approx. 440,000, 752(H) x 582(V)
Synchronization Internal
Signal-to-noise ratio 50dB (AGC OFF)

Sensitivity (at 50% signal) 0,02 Lux at F1.2
Horizontal resolution 540 TVL
Rotation range 360°
Automatic gain control 28dB max.
Gamma correction approx. 0.45
High-speed shutter (ESC) 1/50 ~1/100,000sec.
White balance (ATW) 2000 ~8000K, Automatic
Backlight compensation Automatic
Aperture Correction (APC) Horizontal and vertical
Day-Night Electric TDN by ICR
Video outputs (type) CVBS, VBS
Video outputs 1Vp-p, (C)VBS, 75ohms, BNC
Lens F2.0/3.7mm with fixed iris
Manual pan/tilt 3-axis, ball gimbal
Horizontal angle of view 67°
Cable connection Video (BNC), 12VDC (DC jack)
Operating Temp. range -10°~+50°C
Protection rating IP66, at installation according to the manual
Supply voltage 12VDC, 12VDC (9 ~15VDC), 12VDC ± 0.5V recommended
Power consumption 4.0watts max.
Bubble 57mm (2.25”), clear polycarbonate plastic
Mounting In-ceiling mount, wall mount Surface mount, wall mount
Housing material Vandalism resistant, Aluminum, PC clear bubble
Dimensions See drawings
Weight 190g 210g
Certificates CE
5. Dimensional Drawings

Dimensions: mm