Riccar R700 User manual

INSTRUCTION MANUAL
FOR YOUR RICCAR
SEWING MACHINE
R700 / R1100
T

Name of Paris..
4 *******.. •
Accessories.
Before sewing (Power supply and Sewing lamp). .
Take out extension table, free arm sewing.
Winding the bobbin.
Removing bobbin case and bobbin.
Inserting bobbin into bobbin case.
Inserting bobbin case into shuttle race.
Threading upper thread & Twin needle threading.
Drawing up bobbin thread.
Changing sewing directions.
Leveling machine & Adjusting thread tension. ..
Regulating the presser foot pressure.
Drop feed.
Changing needle.
Fabric. Thread. Needle table.
Sewing (pattern selector) and operation table_
To start sewing.
To finish seam.
Straight stitch.
Zigzag sewing.
Overcasting.
Stretch stitch.
Blind stitch.
Button sewing.
Binding.
Zipper sewing.
Button hole sewing ..
Hemming.
Twin Needle.
Embroidery.
Quilter.
Seam guide.
Maintenance (Cleaning and oiling).
Checking Performance Problems WHAT TO DO
... 1&2
. 3
. A
. 5
. 6
. 7
. 7
.e
.... 9
....10
• 11&12
••••13
•... 13
....14
... .15
... .16
....17
... .IB
... .19
. . . .19
. . ..20
.... 20
21 & 22
. . .23
. ... 23
.... 24
. ... 25
- 2 6
- 27
.... 27
- - - 28
. ... 28
• ••29
• ■ -30

NAME OF PARTS (FRONT VIEW)
1 Pattern selector dial
2 Take up lever
3 Thread tension dial
4 Presserfoot
5 Shuttle cover
6 Extension table
7 Spool pins
8 Top cover
9 Stitch length dial
10 Reverse button
11 Thread guide for upper threading

ACCESSORIES
Scam guide
Button foot
Zigzag foot
(On machine)
Hem guide
Button hole foot
Zipper foot
Screw driver
(Large & small)
Button hole cutter
Darning Plate
~ 3 -
Needle
#11 #14

1. Fit the machine plug into
the machine.
2. Plug the machine to the
power Ripply.
3. Sewing speed can be varied
by the speed controller.
1. Remove or install bulb from
inside of face cover.
2. Open face cover in direction
of arrow.
3. Remove bulb by unscrewing
it counter clockwise.
A. Install a new bulb by screw¬
ing it in clockwise.
5. Use a screw type bulb with
120V/15W. (Max)

. REMOVING EXTENSION TABLE
1. H old the left end of table
and pull out in direction
of arrow.
FREE-ARM SEWING
1. Especially useful when sewing
sleeves, pants leg. tubular
fabrics etc more easily.
2. To sew tubular just slip the
sleeve or pants leg on the free
arm as shown above.
3. This sewing machine can be
used as a flat bed machine,
but easily converts to free
arm machine by removing the
extension table.
— 5

WINDING THE BOBBIN
1. Release stop motion knob.
2. Thread as shown.
3. When bobbin is filled,
tighten stop motion knob.
Push bobbin windor spindle
In direction of arrow.
When bobbin winding is com¬
pleted return spindle to
original position.
When bobbin winding is in¬
correct. release the screw of
upper thread guide and ad¬
just up or down until bobbin
winding is balanced.
6 —

INSERTING BOBBIN CASE INTO SHUTTLE RACE
1. Raise needle to its highest position, pulling
thread to the front, open the latch of bobbin
case and hold it.
2. Holding latch open, place bobbin case onto
centre pin in shuttle and release latch
- 8 -