RIKAIN G60 Serial User manual

1
G60 Serial High Speed Dome Camera
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
1 Do not attempt to disassemble the camera.
To prevent electric shock, do not remove screws or covers.
There are no user-serviceable parts inside.
Ask a qualified service personnel for servicing.
2 Handle the camera with care.
Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling or
storage.
3 Do not expose the camera to rain or moisture, nor try to operate it in wet areas.
This product is designed for indoor use or locations where it is protected from rain and moisture.
Turn the power off immediately and ask a qualified service personnel for servicing.
Moisture can damage the camera and also create the danger of electric shock.
4 Do not use strong or abrasive detergents when cleaning the camera body.
Use a dry cloth to clean the camera when it is dirty.

2
Use the camera under conditions where temperature is between –10°C - +50°C (14°F- 122°F) [Recommended
When the dirt is hard to remove, use a mild detergent and wipe gently. Care should be taken not to scratch the
dome when wiping it.
Afterwards, wipe off the remained part of the detergent in it with a dry cloth.
5 Never face the camera towards the sun.
Do not aim the camera at bright objects. Whether the camera is in use or not, never
aim it at the sun or other extremely bright objects. Otherwise, blooming or smear maybe caused.
6 Never face the camera towards a place exposed to light sources for a long time.
If light sources such as spot light cause burn-in on the display screen, part of image
may discolor due to deterioration of color filter in CCD when changing aim of the camera etc.
7 The outdoor dome camera power source is AC230 V
This camera is designed for mounting on the ceiling or wall. Using this camera installed upside down, for
example, mounted on the floor, may cause malfunction.
8 Do not operate the camera beyond the specified temperature, humidity or power source ratings.
Do not use the camera in an extreme environment where high temperature or high
humidity exists. Do not place near heat sources such as radiators, stoves or other
units that produce heat.

temperature: +40°C (104°F)], and humidity is below 90 %. The input power source is AC 230V.
9 Do not install the camera near the air out-let of an air conditioner.
The lens may become cloudy due to condensation if the camera is used under the
following conditions.
• Rapid temperature fluctuations by switching the air conditioner on and off.
• Rapid temperature fluctuations due to frequent door opening and closing.
• Use in an environment where eyeglasses become foggy.
• Use in a room filled with cigarette smoke or dust.
If the lens becomes cloudy due to condensation, remove the dome cover and
wipe all moist surfaces with a soft cloth.
Burn-in of an image may be caused on the fluorescent screen of CRT.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage constituting a risk of
electric shock is present within this unit.
3

This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this unit.
2、INSTALLATION
INDOOR DOME OUTDOOR DOMR
Dimension
4

INDOOR BRACKET
CEILING MOUNT WALL MOUNT
WALL MOUNT
5

CEILING MOUNT
EMBEDDED MOUNT
6

OUTDOOR WALL Wall MOUNT
MOUNT WITH POWER BOX
柱装支架尺寸 外墙角支架
POLE MOUNT CORNER MOUNT
(pole diameter Ø100-150mm)
7

WALLMOUNTBRACKET POWERBOX SUNSHIELD
8

2.1INDOOR SURFACE MOUNT
1. Decide the mount position on the ceiling
Drill 4 holes on firm ceiling for M4 screws
9
2. Mount the mount base on the ceiling with 4-M4 screws
3.Install the P/T/Z Module in the mount base with clock
direction.
装饰圈
定位点

10
2.2 INDOOR CEILING MOUNT
1 Drill four holes on firm ceiling for M6 expansion bolts
with heavy-duty electrical drill . Mount the base of ceiling
bracket with 4nuts to the 4 expension bolts on the ceiling
2 Pull power ,RS485 and video cables the ceiling bracket
base form the side concave cut.
3 Install the P/T/Z module in the mount base with right
clock direction
支紧螺丝
支紧螺丝
旋紧
定位点

2.3 INDOOR WALL MOUNT
1 Drill 4 holes on firm wall for M6 expansion bolts with heavy-duty electrical drill . Push M6 expansion bolts into
the holes.
2 Install the P/T/Z module in the mount base
in the clock direction
11

2.4 INDOOR EMBEDED MOUNT：2.Mount the embedded bracket on the false ceiling
1.Cutaholeasfollowinginthefalseceiling
12
3.Fix the embedded bracket with the supplied 4.Mount the secure line to the mount base
3 screws
防坠落保险索

5Install the P/T/Z mount in the mount
Base with the clock direction
13
装饰圈

6.Mount the decorocting ring with 2 screws
14
Ring

2.5 OUTDOOR MOUNT
A1WITH POWER BOX
1 Mount the power box on the confirm wall
2. Pull power, RS485 and video cables through the wall bracket
3.Connect all the cable in the power box
4.Mount the wall bracket on the power box with 4 nuts
5.Tigten the screw as following
15
防坠落保险索
协议码、和地址码开关

A2WITHOUT POWER BOX
1Mount the wall bracket on the confirm wall
16
2. Pull all the RS485 ,video and power cables through the wall bracket
3.Tigten the screw as following
协议码、和地址码开关
防坠落保险索

17
2.5 OUTDOOR CEILING MOUNT
B1WITHOUT POWER BOX
1Mount the ceiling bracket on the confirm ceiling
2. Pull all video ,RS485 and power cables through the ceiling bracket
3.Installate the P/T/Z module in the outdoor housing with the clock
direction
4.Tighten the screw as following
防坠落保险索
协议码、和地址码开关

OUTDOOR POLE MOUNT 18
B2 with power box
1Mount the power box on the confirm ceiling
2. Mount the ceiling bracket on the power box
3.Pull the video ,RS485 and power cables through the ceiling bracket
4. Install the P/T/Z module in the outdoor housing with right clock
direction
5. Tighten the screw as following
协议码、和地址码开关
防坠落保险索

without power box mounting as following
协议码、和地址码开关
防坠落保险索
19

OUTDOOR POLE MOUNT
with power box
mounting as following
20
协议码、和地址码开关
防坠落保险索