Rivers edge Xl ladder stand User manual

Get parts online at

www.HuntRiversEdge.com

GAS/OIL

RATIO

50:1

PARTICIPATING MEMBER

PRODUCT MEETS

INDUSTRY STANDARDS

RECOGNIZED BY

P/N: 24132

REV2: 04/12/17

Maximum Height

18' to shooting rail

Wear Your Harness!

Operator's Manual

MODEL RE648

XL™

Ladder Stand

WE ARE HUNTERS

Maximum Field Rating

300 lbs

Tree Diameter Range

12" to 20"

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5

Operator's Manual

XL Ladder Stand

WARRANTY

RETI oers a one year warranty for all components of the treestand. These warranties apply to the original owner with a proof of purchase.

These warranties begin on the date of purchase by the rst retail consumer and continue for the period specied above. These warranties

apply to products that are not modied, abused or used in a manner that deviates from the product’s intended usage. Minor fading in color

is normal and is not covered by warranty. Any corrosion of painted surfaces that occurs as a result of paint being removed or damaged is also

not covered by warranty. RETI oers no other warranty expressed or implied. Products for which warranty work has been approved must be

sent directly to RETI and performed by RETI. To obtain warranty service and/or replacement instructions, you must obtain prior approval

from RETI before shipping your package to us by calling our customer service department at 800-450-3343 or by writing to: RETI, P.O.

Box 755, 1160 Eighth Avenue, Cumberland, WI 54829 for a return material authorization number (RMA#). All items must be shipped

prepaid. RETI will, at no charge, repair or replace, in RETI’s sole discretion, any product that satises the conditions stated above. RETI retains

the right to change models, specications and price without notice.

This equipment has been manufactured under strict quality and safety guidelines. As with any equipment of this type, full understanding of

the instructions and its use is mandatory and imperative for the safety of its user. RETI is not responsible for any damages or injuries sustained

due to improper use or modication of any of its products, or resulting from any use which deviates from the product’s intended usage. RETI

is not responsible for any injuries sustained due to failure to read and adhere to the instructions for use. Any misunderstanding or questions

regarding the products of their use should be directed to RETI prior to any use. All RETI treestands are sold with a full body harness (“Fall

Arrest System”) that meets standards recognized by theTreestand Manufacturer’s Association (“TMA”). It is the owner's sole responsibility

to inspect the product regularly for damage, improper installation, or conditions that could jeopardize the ultimate safety of the product. Failure

to use or improper use of the provided Fall Arrest System may result in serious injury or death. ALWAYS wear the provided Fall Arrest System

while using this product. Owner is responsible to understand and follow product eld weight rating and must never exceed maximum

weight rating. RETI is not responsible for any malfunction or injury resulting from normal wear and tear, damage caused by improper use,

improper maintenance, negligence or accidents. This product, if used safely as intended, will provide trouble free service for the useful life of

the product. We hope you will enjoy the quality of our products for years to come, and have a safe hunt.

INTRODUCTION

Rivers Edge® Treestands are engineered with you the hunter in mind. We appreciate your purchase of one of our world

class treestands. Follow these few simple instructions and your stand will provide you many years of trouble-free

pleasure. Instructions should be kept in a safe place and reviewed at least annually.

If for any reason you have a problem with your product, DO NOT return to the retailer, contact the Rivers Edge®

customer service department at 800-450-EDGE (3343) for assistance.

CONTENTS

Introduction/Warranty ..................................................................................................................................................................................................................2

Warnings.........................................................................................................................................................................................................................................2-3

Inspection and Maintenance ......................................................................................................................................................................................................3

Hardware Identication Chart....................................................................................................................................................................................................5

Tools Needed ....................................................................................................................................................................................................................................5

Assembly Instructions ...............................................................................................................................................................................................................6-8

Setup and Use Instructions.................................................................................................................................................................................................10-11

Illustrated Parts Breakdown...................................................................................................................................................................................................... 12

Parts List........................................................................................................................................................................................................................................... 13

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 3

Operator's Manual

XL Ladder Stand

MODEL RE648

MAXIMUM USE HEIGHT  18' TO SHOOTING RAIL

MAXIMUM OCCUPANCY  ONE 1

TOTAL WEIGHT LIMIT  300 LB

TREE DIAMETER RANGE  12”TO 20”

WARNING

This product carries strict height and weight restrictions.

Do Not use this product if you exceed the total weight

limit. Please note that the total weight limit includes the

user(s) and their equipment.

WARNING

When hunting from a treestand falls can occur any

time after leaving the ground causing injury or death.

Always wear a Fall Arrest System (FAS) comprising a full

body harness at all times after leaving the ground. You

must stay connected at all times after leaving the ground

while using climbing and hang-on treestands. Single

safety belts and chest harnesses are no longer allowed

and shall never be used. If you are not wearing a full body

harness properly attached to the tree that is protecting

you from a fall, do not leave the ground.

Read and understand all of the manufacturer’s Warnings

and Instructions and use all safety devices provided by

the manufacturer. Contact the manufacturer for any

questions. Failure to do so could result in injury or death.

Never exceed the total weight limit of the treestand.

Never use a treestand during inclement weather such as

rain, lightning, windstorms or icy conditions and end your

hunt and return to the ground if inclement conditions arise.

Never use a treestand while using drugs (even

prescription drugs) or alcohol.

Never use a treestand while feeling ill, nauseous or dizzy,

or if you have a prior medical condition that could cause

a problem, that is, heart condition, joints that lock-up,

spinal fusions, etc., or if you are not well rested. Never

sleep in stand.

Never use a treestand on a dead, leaning, diseased or

loose barked tree, or a utility pole. Always avoid electrical

power lines.

Never rely on a tree branch for support.

WARNING

Never jump or bounce on a treestand to seat it to the tree.

Pull up a bow, backpack, or rearm or other equipment

only after being secure in the treestand and a rearm

must be pulled up with it unloaded, chamber open, and

muzzle down.

Always inform someone of the hunting location, where

the treestand will be located and the expected duration

of the hunt.

A signal device such as a mobile phone, radio, whistle,

signal are or personal locator device (PLD) must be on

your person and readily available at all times.

Inspect the treestand and all safety devices each time

before use and Do Not store a treestand outdoors when

not in use.

Never modify your treestand in any way by making

repairs, replacing parts, or altering it except if explicitly

authorized in writing by the manufacturer.

Practice installing, adjusting and using your treestand at

ground level prior to using it at elevated positions. Study

your new stand to become familiar with all of its features

and design. Doing so will conrm that the product is

manufactured, assembled and installed correctly.

Instructions (written and video) shall be kept in a safe place

and reviewed at least annually. It is the responsibility of

the treestand owner to furnish the complete instructions

to any person who borrows or purchases the treestand.

Use at least three (3) people to install or take down a

ladder treestand.

The criss-cross straps/ropes and stabilization devices

must be attached before climbing to the platform.

When installing a ladder stand, always bounce on the

rst rung to set the ladder into the ground according to

manufacturer’s instructions before proceeding to climb

any higher.

Check every ladder section connection every time you

use the stand before you leave the ground. If ladder

sections are separating, do not use the stand.

Check the ground under the stand to make sure it is rm

and level. Sloping ground or uneven surface (one side on

a rock) can cause your ladder to tilt or shift o the tree as

you climb.

Always maintain three (3) points of contact when

climbing a ladder treestand. Proper three-point contact

means having either two feet with one hand or one foot

with two hands on the step portion of the ladder or

climbing aid at all times.

READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE ASSEMBLY

STOP

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5

Operator's Manual

XL Ladder Stand

WARNING

Always lean forward as you climb and attach your harness

to the tree before securing the platform to the tree and

stepping onto the platform.

Never exceed the stated maximum use height.

Do Not use this product until you have watched the

included treestand safety DVD, understand it, and

practiced the techniques for safe hunting discussed in

this DVD.

Read and perform all inspection and maintenance tasks

before each and every use. Replace any questionable

components immediately with RETI original replacement

parts.

Do Not crush tubing when tightening bolt assemblies!

Identify and familiarize yourself with all parts before you

start. Bolt identication chart can be found in the back.

Double check assembly steps to be certain you have

correctly assembled this product.

Never use any product that has not been maintained or

inspected properly - Your life depends on it!

Replace any and all treestand straps every two years or

when any signs of damage or wear exist before.

Always wear the appropriate footwear when using a

ladder treestand. A good non-slip safety boot is important

to your personal safety. Be especially careful that boot

laces do not get hooked on the stand or any of its

components (tuck shoelaces into boots before climbing).

BEFORE EACH USE PERFORM THE FOLLOWING:

• Inspect all webbing, rope, cord, and strap assemblies for

wear or damage.

• Inspect cables and/or cable ends for damage or kinking.

• Inspect all hardware and chain components for damage.

• Inspect for any structural damage to product. (If any exists

call RETI customer service.)

• Inspect all nut and bolt assemblies to be certain none are

loose.

• Inspect for any missing parts.

• Lubricate all pivot and slide together points with powder

graphite, petroleum jelly or silicone spray to prevent noise,

wear and rust.

• Inspect entire product for any rust, corrosion, cracks,

freezing, excessive heat or rotting damage that may eect

the safety of your product. Discard any questionable

product.

• Inspect entire product for any structural damage - pay

close attention to all weld locations. (Return to factory for

repair or discard product if any damage is found.)

• Using correct wrenches inspect all nut & bolt assembly

locations and snug up any that may be loose. Be careful

not to crush tubing when tightening!

• Inspect and check operation of all cables, cable ends, cord,

rope, webbing, and strap or chain assemblies. Replace with

factory new any item or assembly that shows signs of wear,

damage, kinking, or functions incorrectly.

• Inspect seat. Replace any seat with factory new that shows

signs of structural damage or wear.

• Inspect all hardware for wear or damage, also be sure you

have no missing parts.

• Never modify your stand in any way by making repairs,

replacing parts, or altering adding or attaching anything

to it except if explicitly authorized in writing by the

manufacturer.

WARNING

Only use approved RETI parts. Failure to do so may result

in serious injury or death!

INSPECTION AND MAINTENANCE

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 5

Operator's Manual

XL Ladder Stand

HARDWARE IDENTIFICATION CHART Bolts shown are for size reference.

Extra hardware may be included in the parts bag.

TOOLS NEEDED

2- 7/16" Wrenches 2- 1/2" Wrenches

22 1/4-20 X 1-1/4" Bolt - Qty 1

26 1/4-20 X 2-3/4" Bolt - Qty 2

23 5/16-18 X 1-3/4" Bolt - Qty 13

27 5/16-18 X 2-1/2" Bolt - Qty 6

24 1/4-20 X 2-1/4" Bolt - Qty 2

25 1/4-20 X 3-1/4” Bolt - Qty 4

28 5/16 X 18 X 2-1/4” Bolt - Qty 4

29 5/16 X 18 X 3-1/4" Bolt - Qty 2

5/16" Wing Nut

Qty 1

1/4" Nut

Qty 8

Lockpin

Qty 5

5/16" Nut

Qty 24

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5

Operator's Manual

XL Ladder Stand

All assembly must be done in this order at ground

level before uprighting.

Do not remove labels/warnings from product, they are

there for your safety.

Recommended for adult use only.

1. Attach the front platform (6) and the rear platform (7)

together using two 5/16 x 18 x 2-1/4" bolts (28) and two

5/16" nuts (32). SEE FIGURE 1

2. Attach the platform supports (4) to the top of the rear

platform (7) by using four 5/16-18 x 2-1/2" bolts (27) and

four 5/16" nuts (32). SEE FIGURE 2

3. Attach the brace at bars (18) to the back of the rear

platform (7) and to the platform supports (4) using four

5/16-18 x 1-3/4" bolts (23) and four 5/16" nuts (32).

SEE FIGURE 2

4. Attach rears of both armrests (17) to rears of seat side rails

(9) and to the platform supports (4) using two 1/4-20 x

3-1/4" bolts (25) and two 1/4" nuts (31). SEE FIGURE 3

5. Attach fronts of both armrests (17) to fronts of seat side rails

(9) using two 1/4-20 x 2-1/4" bolts (24), two yellow washers

(36) and two 1/4" nuts (31). SEE FIGURE 3

6. Attach the tree blade (10) to the backs of the seat side rails

(9) using two 5/16-18 x 2-1/2" (27) and two 5/16" nuts (32).

SEE FIGURE 3

EXPANDED METAL REMOVED FOR CLARITY

ASSEMBLY INSTRUCTIONS

IMPORTANT ASSEMBLY TIP:

Do not tighten any nut and bolt combinations completely until all

parts are assembled together! Finger tighten plus one turn of a

wrench only! This will temporarily hold the lock nut on the bolt while

helping alignment of all parts! After all parts are assembled together,

all nut & bolt combinations must be completely tightened.

FIGURE 1

FIGURE 2

FIGURE 3

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 7

Operator's Manual

XL Ladder Stand

7. Slide the ared platform rails (8) into the seat side rails (9).

Insert two 5/16-18 x 1-3/4" bolts (23) and nger tighten with

two 5/16" nuts (32). SEE FIGURE 4

8. Attach the footrest (16) to the ared platform rails (8) and

front platform (6) using two 5/16 x 18 x 3-1/4" bolts (29),

six yellow washers (37) and two 5/16" nuts (32). The yellow

washers (37) should be on all four sides of the footrest (16)

and on the outside of the ared platform rails (8).

SEE FIGURE 4

9. Attach the top ladder rung (3) to the front of ared rails (8)

using two 5/16 x 18 x 2-1/4" bolts (28) and two 5/16" nuts

(32). Tighten all loose hardware at this time. SEE FIGURE 4

10.Slide shooting rail "A" (14) into shooting rail "B" (15) and

attach together using one 1/4-20 x 1-1/4" bolt (22) and one

1/4" nut (31). SEE FIGURE 5

11. Attach the assembled shooting rail (14 & 15) and seat platform

(11) to the armrests (17) using two 1/4-20 x 3-1/4" bolts (25),

four thick polymer washers (34), two yellow washers (36) and

two 1/4" nuts (31). Thick polymer washers (34) go between

seat platform and armrests and between armrests and

shooting rail. SEE FIGURE 5

12.Attach two bumper pads (38) to the seat side rails (9) so

that the seat will rest on them when in the down position.

SEE FIGURE 5

13. Attach three plastic spacers (35) to both armrests (17) using

two 1/4-20 x 2-3/4" bolts (26) and two 1/4" nuts (31).

SEE FIGURE 5

14. Insert ared platform rails (8) into the pockets of top ladder

section (1) and secure using two 5/16-18 x 1-3/4" bolts (23)

and two 5/16" nuts (32). SEE FIGURE 6

15. Attach the platform braces (5) to the top ladder section (1)

and to the rear platform (7) using four 5/16-18 x 1-3/4" bolts

(23) and 5/16" nuts (32). SEE FIGURE 6

16. a. Attach the two armrest covers (20) to the armrests (17) and

the shooting rail cover (19) to the shooting rail (14 & 15) by

wrapping around tubing and attaching Velcro together.

b. Attach the seat cushion (21) to the seat platform (11) by

wrapping straps around metal frame and securely fastening

all plastic buckles together. Pull straps tight so seat is not

loose.

17. Slide together the two ladder sections (2) and the top ladder

section (1) on the ground and secure together using four

spring lock pins (30). SEE FIGURE 7

837

32 16

37 6

FIGURE 4

FIGURE 5

FIGURE 6

FIGURE 7

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5

Operator's Manual

XL Ladder Stand

18.Assemble the horizontal stabilizer bar as follow:

a. Slide the stabilizer bar (12) into stabilizer bar extension

tube (13) and secure together with spring lock pin (30).

SEE FIGURE 8

NOTE: Spring lock pin (30) must go through both the

horizontal stabilizer bars at the appropriate hole to

achieve the desired distance from the tree. Adjustment

in length may be needed when ladder is up righted

later in instructions.

b. Attach the forward end of the horizontal stabilizer bar

assembly to a rung of the ladder using 5/16-18 x 1-3/4"

bolt (23) and 5/16" wing nut (33). SEE FIGURE 8

19. Preassemble 16’stabilizer straps (42) and 6’ ratchet strap (41)

as follows:

a. Attach the two long ends of the 16’ stabilizer (criss-cross)

straps (42) to each side of the seat side rail (9) between

the armrests and the tree blade. These long stabilizer

straps should be attached by pulling the free end of the

strap through the loop end of the strap to create a cinch

knot around the rail tube. SEE FIGURE 9

b. To aid in the ease of installation, pre-attach each end of

the 6’ ratchet strap (41) to each side of the seat side rail,

between the 16’ stabilizer straps (42) and the tree blade.

Use the same method as above. SEE FIGURE 9. This

way each end of the main ratchet strap is pre-attached

before the stand is lifted from the ground. SEE FIGURES

10 AND 11 showing the locations of the four ends

attached.

FIGURE 8

FIGURE 9

FIGURE 10

FIGURE 11

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 9

Operator's Manual

XL Ladder Stand

WARNING

Double check assembly steps to be certain you have

correctly assembled this product.

Study your new stand to become familiar with all of its

features and design. At ground level, following provided

use instructions, practice attaching stand to tree and

removing stand from tree. Practice sitting, standing, and

using this product before attaching overhead. Save these

instructions for future reference. You must always use the

provided Fall Arrest System (FAS) while using this product.

Always use at least three (3) people to install or take down

a ladder treestand. Always have two people stabilize the

ladder before climbing to the platform the rst time after

every set-up.

Be absolutely sure the tree blade(s) on stand and the

stabilizer bar are contacting tree before climbing ladder.

Stabilizer bar must always be correctly and securely

attached to ladder and tree before climbing ladder.

Make sure ladder bottom is rmly seated on dry, level

ground. Attach your harness tether to the tree before

securing the platform to the tree and stepping onto

platform. Refer to the Full Body Harness instructions.

Never ascend or descend ladder without criss-cross

straps/ropes securely holding ladder to tree and stabilizer

bar securely attached. Failure to correctly perform these

steps can cause the ladder to collapse/buckle-over

backwards during the initial ascent to attach ratchet strap

resulting in serious injury or death.

Always lean forward as you climb and attach your harness

to the tree before securing the platform to the tree and

stepping onto the platform.

WARNING

Always maintain three (3) points of contact when

climbing a ladder treestand. Proper three-point contact

means having either two feet with one hand or one foot

with two hands on the step portion of the ladder or

climbing aid at all times.

Always wear the appropriate footwear when using a

ladder treestand. A good non-slip safety boot is important

to your personal safety. Be especially careful that boot laces

do not get hooked on the stand or any of its components

(tuck shoelaces into boots before climbing).

Never stand on seat, it is designed for sitting only.

Do Not allow excessive strap buildup in ratchet as this

will prevent the ratchet teeth from engaging causing

slippage.

Always attach ratchet straps securely while using this

product!

If seat is removable, be certain it is securely attached

when in use.

Some models include a shooting rail. Never lean against,

lean over, or sit on shooting rail. It is designed as a

shooting rest only. Always be aware that the shooting rail

can swing to one side or pivot up and down.

Some models include a footrest, which is designed as a

footrest only. Never stand on footrest! Always be fully

aware of foot placement.

Some models include a multi-piece stabilizer bar system.

Be sure attachment hardware goes through both the

extension tube and the stabilizer bar.

READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE SETUP AND USE

STOP

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5

Operator's Manual

XL Ladder Stand

SETUP AND USE INSTRUCTIONS

1. With assembled product lying on the ground, position one

person at bottom end of ladder lying on the ground. This

person has to prevent the ladder end from tilting up when

platform end is lifted and prevent the ladder from skidding

across ground.

2. a. Position two people at the platform end of the ladder,

lift the platform end and continue uprighting by walking

toward bottom end of ladder and moving hands along

ladder legs. Stand ladder up against chosen straight tree

on dry, level ground. Use caution when ladder comes over

center against the tree. SEE FIGURE 10A

b. Step back and look at the ladder top to see that it is level.

Adjust as needed to achieve a level platform top. Make sure

tree blade is contacting tree. SEE FIGURE 10B

c. Step down hard on bottom step to push ladder legs into

the ground. SEE FIGURE 10C

3. While two people hold the stand in place, the third person

should connect the horizontal stabilizer bar to the tree.

Adjust the length of the stabilizer bar as need so it contacts

the tree and is level to the ground. Then secure it to the

tree with the 6' cam strap (40) by forming a cinch knot with

both ends of the strap and running the long end of the

strap through the cam buckle. SEE FIGURES 11 and 12.

During installation and removal of ladder treestands, you

must always and properly use the included Full Body Harness

(Fall Arrest System). Refer to the Full Body Harness instructions

included with this product for proper use.

FIGURE 11

FIGURE 12

FIGURE 10

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 11

Operator's Manual

XL Ladder Stand

4. a. Loop the d-loop end of the two 16' criss cross straps

(42) through the loop end to form a cinch knot around

the ladder rail tube. Secure beneath a step rung, at the

stabilizer bar height location. SEE FIGURE 13A.

b. With the stand level and being held in place by two

people, the third person must cross one of the 16' criss

cross straps (42) behind the tree and feed the free end

through the opposite d-loop. SEE FIGURE 13B-E.

c. Criss cross the other 16' stabilizer strap (42), forming an

"X" pattern on the backside of the tree and feed the free

end through the opposite d-loop. SEE FIGURE 13B-E.

5. Make sure the criss cross straps and stabilizer bar strap are

snug and the tree blade is still contacting the tree.

NOTE: This ground level ladder-to-tree attachment will

prevent the ladder from pulling away from the tree

while ascending to the top for nal 6' ratchet strap (41)

attachment. The same holds tree when the ladder is

removed.

6. With two people securely holding the ladder, the third person

must now use the three point contact climbing method to

slowly climb the ladder. Make sure to keep a constant hand

grip on the ladder at all times. Always lean forward, toward the

tree, to keep the platform tree blade against the tree.

NOTE: Make sure the ladder bottom is rmly seated on

dry, level ground. Attach your harness tether to the tree

before securing the platform to the tree and stepping

onto platform. Refer to the Full Body Harness instructions

included with this product.

7. Standing on ladder step, lean toward tree with previously

installed 6' ratchet strap (41) now in hand.

a. Wrap the previously installed end of the long strap

around the tree and feed through the slot in the ratchet

mechanism. SEE FIGURE 14A.

NOTE: Be sure to feed the long strap correctly so there are

no twists in the strap.

b. Pull tail of long strap until most of the slack is taken out. Be

sure entire strap is even and at the same level all around

tree. SEE FIGURE 14B.

c. Use the ratchet to tighten the strap to tree. The tightened

strap will stabilize the stand to tree and prevent

movement. SEE FIGURE 14C.

NOTE: Make sure there is at least two full revolutions

of strap on the ratchet spool before the strap tightens.

Proper tension will ensure the stand is secured to the tree.

Do not allow excessive strap to build up in the ratchet as

this will prevent the ratchet teeth from engaging and can

cause slippage.

To release ratchet, simply pull the release lever and open

tightening lever wide open (at). SEE FIGURE 14D.

8. If necessary, re-check and adjust the 6' ratchet strap (41), 16'

criss cross straps (42) and horizontal stabilizer bar assembly to

securely attach the treestand to the tree. The tree blade must

be touching the tree.

9. Attach the backrest portion of the seat cushion by securing

the bungee cord around the tree.

10. Reverse setup and use instructions to take ladder down.

FIGURE 13

FIGURE 14A FIGURE 14B

FIGURE 14C FIGURE 14D

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5

Operator's Manual

XL Ladder Stand

15 26

Mesh Hidden for Clarity

18 23

337

ILLUSTRATED PARTS BREAKDOWN

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 13

Operator's Manual

XL Ladder Stand

Maximum Height - 18' to shooting rail

(Never extend this stand beyond this maximum use height)

Single User Maximum Field Rating - 300 lb

(This is the maximum combined total weight of the user, their

clothing, and gear while on the ladder, platform and/or seat)

No more than one person should occupy any part of this

stand at any time.

Tree Diameter Range - 12" to 20"

(Select only strong, healthy trees that are straight with

no loose bark)

ITEM # PART # DESCRIPTION QT Y.

1 24146 TOP LADDER SECTION 1

2 24145 LADDER SECTION 2

3 23703 TOP LADDER RUNG 1

4 24125 PLATFORM SUPPORT 2

5 24126 PLATFORM BRACE 2

6 24133 PLATFORM FRONT 1

7 24134 PLATFORM REAR 1

8 24127 FLARED PLATFORM RAIL 2

9 24124 SEAT SIDE RAIL 2

10 24142 TREE BLADE 1

11 24141 METAL SEAT FRAME 1

12 23698 STABILIZER BAR "A" 1

13 23699 STABILIZER BAR

EXTENSION "B"

14 24138 SHOOTING RAIL "A" 1

15 24139 SHOOTING RAIL "B" 1

16 24140 FOOTREST 1

17 24137 ARMREST 2

18 24136 BRACE FLAT BAR 2

19 48738 SHOOTING RAIL COVER 1

20 48736 ARMREST COVER 2

21 24143 SEAT/BACKREST CUSHION 1

22 8909B 1/4-20 X 1-1/4 IN BOLT 1

23 8655B 5/16-18 X 1-3/4 IN BOLT 13

24 48271B 1/4-20 X 2-1/4 IN BOLT 2

25 48273B 1/4-20 X 3-1/4 IN BOLT 4

26 67540B 1/4-20 X 2-3/4 IN BOLT 2

27 53730B 5/16-18 X 2-1/2 IN BOLT 6

28 27950 5/16 X 18 X 2-1/4 IN BOLT 4

29 27966 5/16 X 18 X 3-1/4 IN BOLT 2

ITEM # PART # DESCRIPTION QT Y.

30 19847 6MM X 50.8MM ROUND

LOCKPIN

31 48752B 1/4 IN NUT 8

32 60G5NYB 5/16 IN NUT 24

33 27951 5/16 IN WING NUT 1

34 MK036-6004 THICK POLYMER WASHER 4

35 10347 PLASTIC SPACER 6

36 23572 YELLOW WASHER 6.5MM

X 19MM X 2MM

37 23523 YELLOW WASHER 8.1MM

X 19MM X 2MM

38 48102 BUMPER PAD 2

ITEMS BELOW ARE NOT SHOWN

39 10531 SAFETY HARNESS / FALL

ARREST SYSTEM

40 MK0211401 6' CAM BUCKLE STRAP 1

41 MK0111601 6' RATCHET STRAP 1

42 MK0344511 16' STABILIZER STRAP 2

43 48800 TREE STAND SAFETY DVD 1

PARTS LIST

*All weights, specications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact. Warning labels in some product