Rivers Edge Pack-n-Stack RE622 User manual

OMRELD001
Revised 01/27/12
0 2012 RETI
All Rights Reserved.
Tom
Certified to TMA
Standards by an
Independent
sting Laboratory
Get parts online at
www.huntriversedge.com
INCLUDES MODELS:
D RE622, Pack-n-StackTm Ladder
fl
RE627, OasisTM Ladder
RE628, Jumbo Jack' Ladder
 RE630, Relax'
D
RE631, Relax' Wide
i
rctivarc„._
C3 G
TREE STANDS
Operator's Manual
One-Man
Ladder Stands
PACK-N-STACK""
Model RE622
RELAXTM WIDE
Model RE631
JUMBO JACK"'
Model RE628

Operator's Manual
Rivers Edge® One-Man Ladder Stands
,s Edge® Treestands are engineered with you the hunter in mind. We appreciate your purchase of one of our world class treestands. Follow
these few simple instructions and your stand will provide you many years of trouble-free pleasure. Instructions should be kept in a safe place and
reviewed at least annually.
If for any reason you have a problem with your product,
DO NOT return to the retailer,
contact the Rivers Edge® customer service department at
800-450-EDGE (3343) for assistance.
CONTENTS
Introduction/Warranty

2
Warnings 
3
Inspection and Maintenance 
4
Assembly/Parts Explosion/Parts List (RE622) 
5-9
Assembly/Parts Explosion/Parts List (RE627)

10-16
Assembly/Parts Explosion/Parts List (RE628) 
17-23
Assembly/Parts Explosion/Parts List (RE630) 
24-28
Assembly/Parts Explosion/Parts List (RE631) 
29-34
Set-Up and Use Instructions (All ladders in this manual) 
35-36
Bolt Guide 
37
WARRANTY
Rivers EdgeTreestands, Inc., offers a lifetime warranty to be free from defects in materials and workmanship.This warranty applies to the original owner with a proof of purchase.
All items attached to our stands (seat, strap, rope, wood, etc.) that are degradable are warranted for a period of one year. There is no warranty on paint. This warranty applies to
products that are not modified, abused or misused in a manner that deviates from the products intended usage. Rivers Edge° Treestands offers no other warranty expressed
or implied nor is to be held liable for any damage that may result from any defect in a treestand manufactured by them. Warranty work must be sent directly to Rivers Edge®
Treestands and performed by them. To obtain warranty service and/or replacement instructions, you must have prior approval from Rivers Edge Treestands before
shipping your package to us by calling our customer service department at 800-450-EDGE (3343) or by writing to: Rivers Edge Treestands, Inc., P.O. Box 755, 1160
Eighth Avenue, Cumberland, WI 54829 for a return material authorization number
(RMA4).
All items must be shipped prepaid. Rivers Edge' Treestands will at no charge,
repair or replace, at their discretion, any defective stand which falls under the conditions stated above. Rivers Edge°Treestands retains the right to change models, specifications
and price without notice.
NOTE: You must always use the provided full body harness (fall arrest system)that meets TMA standards while using this product!
This equipment has been manufactured under strict quality guidelines. As with any equipment of this type, full understanding of the instructions and its use is mandatory for
the safety of its user, Rivers Edge® Treestands, Inc., is not responsible for any damages or injuries sustained due to improper use or modification of any of its products, or due
to any use which deviates from the products intended usage.The manufacturer also is not responsible for any injuries sustained due to failure to adhere to the instructions for
use. Any misunderstanding of its operation should be directed to manufacturer prior to its use.
ALL RIVERS EDGE° TREESTAND5 COME WITH A FULL BODY HARNESS (FALL ARREST SYSTEM)THATMEETSTMA STANDARDS. It is the owner's responsibilityto inspect
the product regularly for damage that could inhibit the ultimate safety of the product. Failure to use or improper use of the provided Full Body Harness (Fall Arrest System) that
meets TMA standards may result in serious injury or death. ALWAYS wear the provided Full Body Harness (Fall Arrest System) that meets TMA standards while using this product.
Owner is responsible to check product field rating and must never exceed maximum weight rating stated. Rivers Edge Treestands, Inc., is not responsible for any
malfunction due to normal wear and tear and/or damage caused by improper use, improper maintenance or accidents. This product if used safely as intended, will give you
years of trouble free service. We hope you will enjoy the quality of our products for years to come, and have a safe hunt.
For replacement parts, phone 800-450-EDGE (3343) or go online to www.HuntRiversEdge.com
.
Check for parts online at
www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5
2

DO NOT USE THIS PRODUCT UNTIL YOU HAVE WATCHED
THE INCLUDED TREESTAND SAFETY DVD, UNDERSTAND IT
AND PRACTICED THE TECHNIQUES FOR SAFE HUNTING DIS-
CUSSED IN THIS DVD.
YOU MUST ALWAYS USE THE PROVIDED FULL BODY HAR-
NESS (FALL ARREST SYSTEM) THAT MEETS TMA STAN-
DARDS WHILE USING THIS PRODUCT. SINGLE SAFETY BELTS
AND CHEST HARNESSES ARE NO LONGER ALLOWED AND
SHOULD NEVER BE USED.
IF YOU ARE NOT WEARING A FULL BODY HARNESS THAT
IS PROTECTING YOU FROM A FALL, DO NOT LEAVE THE
GROUND.
FAILURE TO USE OR IMPROPER USE OF THE PROVIDED FULL
BODY HARNESS (FALL ARREST SYSTEM) THAT MEETS TMA
STANDARDS MAY RESULT IN SERIOUS INJURY OR DEATH! READ,
UNDERSTAND AND FOLLOW ALL INSTRUCTIONS. IF ANY IN-
STRUCTIONS ARE NOT UNDERSTOOD OR IF YOU HAVE A PARTS
ISSUE CALL 800-450-EDGE(3343) BEFORE USING.
READ, UNDERSTAND AND FOLLOW ALL ASSEMBLY, INSPEC-
TION, MAINTENANCE, FULL BODY HARNESS (FALL ARREST
-
YSTEM) & USE INSTRUCTIONS PROVIDED BEFORE EACH
E. FAILURE TO FOLLOW ALL WARNINGS AND INSTRUC-
. IONS COULD RESULT IN SERIOUS INJURY OR DEATH.
READ AND PERFORM ALL INSPECTION AND MAINTENANCE
TASKS BEFORE EACH AND EVERY USE (REPLACE ANY QUES-
TIONABLE COMPONENTS IMMEDIATELY WITH RIVERS
EDGE ORIGINAL REPLACEMENT PARTS). DO NOT LEAVE
YOUR STAND OUTDOORS - REMOVE AFTER EACH USE AND
STORE INDOORS!
INSTRUCTIONS SHOULD BE KEPT IN A SAFE PLACE AND RE-
VIEWED AT LEAST ANNUALLY.
DOUBLE CHECK ASSEMBLY STEPS TO BE CERTAIN YOU HAVE
CORRECTLY ASSEMBLED THIS PRODUCT.
DO NOT CRUSH TUBING WHEN TIGHTENING BOLT ASSEM-
BLIES! IDENTIFY AND FAMILIARIZE YOURSELF WITH ALL
PARTS BEFORE YOU START. A BOLT IDENTIFICATION CHART
CAN BE FOUND IN THE BACK.
DO NOT EXCEED THE TOTAL FIELD RATING- 300 LBS.
NEVER USE ANY PRODUCT THAT HAS NOT BEEN MAIN-
TAINED OR INSPECTED PROPERLY - YOUR LIFE DEPENDS
ON IT!
WHEN HUNTING FROM A TREESTAND, FALLS CAN OCCUR
ANY TIME AFTER LEAVING THE GROUND CAUSING INJURY
OR DEATH.
NEVER ATTACH TO A DEAD, ODD-SHAPED, LEANING, DIS-
EASED, LOOSE-BARKED TREE OR UTILITY POLES.
ARNINGS
A
WARNING
A
WARNING
REPLACE ANY AND ALL TREESTAND STRAPS EVERY TWO
YEARS OR WHEN ANY SIGNS OF DAMAGE OR WEAR EXIST
BEFORE
SOME MODELS INCLUDE A FOOTREST, WHICH IS DESIGNED
AS A FOOTREST ONLY. NEVER STAND ON THE FOOTREST.
BE SURE TO RAISE AND LOWER YOUR WEAPON AND GEAR
WITH A HAUL LINE. GUN BARREL END AND ARROW TIPS
MUST BE POINTED DOWN- AWAY FROM YOU.
BE SURE SEAT PAD AND/OR BUCKLES ARE SECURELY AND
CORRECTLY ATTACH ED TO PREVENT ACCIDENTAL REMOVAL.
A WARNING
ALL ASSEMBLY MUST BE DONE BY THREE PEOPLE IN THIS OR-
DER AT GROUND LEVEL BEFORE UPRIGHTING.
NEVER EXCEED THE MAXIMUM STATED USE HEIGHT.
CHECK THE GROUND UNDER STAND TO MAKE SURE IT IS
FIRM AND LEVEL. SLOPED GROUND OR UNEVEN SURFACE
(ONE SIDE ON A ROCK) CAN CAUSE YOUR LADDER TO TILT
OR SHIFT OFF THE TREE AS YOU CLIMB.
CHECK EVERY LADDER SECTION CONNECTION EVERY TIME
YOU USE THE STAND BEFORE YOU LEAVE THE GROUND.
IF LADDER SECTIONS ARE SEPARATING, DO NOT USE THE
STAND.
LUBRICATION IS HIGHLY RECOMMENDED AT SLIDE TO-
GETHER POINTS OF EACH SECTION TO PREVENT BINDING.
SECTIONS ARE STACKED TOGETHER BY SLIDING SECTIONS
TOGETHER, INSIDE OF EACH OTHER. SECTIONS ARE THEN
SECURED WITH SPRING LOCK PINS.
BE SURE ALL LADDER SECTIONS ARE SEATED COMPLETELY
TOGETHER ON SWEDGED OR POCKETED ENDS OF PIPE.
STABILIZER BAR MUST ALWAYS BE CORRECTLY AND SECURELY
ATTACHED TO LADDER AND TREE BEFORE CLIMBING LADDER.
SOME MODELS INCLUDE A MULTI-PIECE STABILIZER BAR
SYSTEM. BE
SURE SPRING LOCK PIN GOES THROUGH BOTH
THE EXTENSION TUBE AND THE STABILIZER BAR.
BE CERTAIN SPRING LOCK PINS ARE LATCHED SECURELY TO
PREVENT ACCIDENTAL REMOVAL.
BE SURE YOUR DOUBLE KNOTS ARE ALL SECURE ON ALL
ROPE CONNECTIONS.
NEVER ASCEND OR DESCEND LADDER WITHOUT TIE-OFF
ROPES SECURELY HOLDING LADDER TO TREE AND STABI-
LIZER BAR SECURELY ATTACHED.
Operator's Manual
111 - C,J Ilholar<„S
4-1. 11a1C1140111,
ft
Wirers Ed Ond-Mantaddet Stands
3
Check for parts online at
www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5

Operator's Manual
Rivers Edge One-Man Ladder Stands
JAYS...
Be physically fit, mentally alert, and well rested before using this product.
Read, understand and follow all warnings and instructions before
use and save for future reference.
Use the provided Full Body Harness (Fall Arrest System) that meets
TMA standards immediately upon reaching foot platform.
Be fully aware of foot placement.
Recommended for adult use only.
Inspect ladder for missing parts, all hardware condition, and
damage before every application, replace if necessary.
Pull up a bow, backpack, firearm or other equipment only after
being secure in the treestand and a fire arm must be pulled up with
it unloaded, chamber open and muzzle down.
Remove ladder after every use, store product indoors.
Use only Rivers Edge ° original replacement parts.
Lean forward, towards tree, when ascending and descending ladder.
Place ladder on dry, level ground.
Lubricate all slide together points to prevent binding, wear, rust and noise.
Avoid all electrical power lines.
Always inform someone of the hunting location, where the
treestand will be located and the expected duration of the hunt.
Carry a signal device such as a mobile phone, radio, whistle,
signal flare or personal locator device (PLD) and it must be readily
available at all times.
pect the treestand and all safety devices each time before use
_1 do not store a treestand outdoors when not in use.
NEVER...
Sleep in a treestand
Use on wet, soft, or unstable ground.
Exceed the total field rating of 300 lb.
Attach to a dead, odd-shaped, leaning, diseased, loose barked trees
or utility poles.
Use on trees with a diameter smaller than 12 inches or no larger
than 20 inches.
Use a treestand during inclement weather such as rain, lightning,
windstorms or icy conditions and end your hunt and return to the
ground if inclement conditions arise.
Alter the original design of your stand.
Jump on or use in a careless manner.
Lean out over edge of device.
Use when intoxicated or using over-the-counter medication or
prescription drugs.
Use a damaged product, replace with new.
Loan your stand to someone else.
Use without stabilizer bar, spring lock pins &tie-off ropes securely attached.
Stand on the seat, it is designed for sitting only.
Use a treestand when feeling ill, nauseous or dizzy, or if you have a
prior medical condition that could cause a problem i.e., heart condition,
ioints that lock-up, spinal fusion, etc. or if you are not well rested.
y on a tree branch for support.
Jump or bounce on a treestand to seat it to the tree
INSPECTION AND MAINTENANCE SCHEDULE
FOR ALL RIVERS EDGE ° PRODUCTS
Inspect all webbing, rope, cord, and strap assemblies for wear or
damage.
Inspect cables and cable ends for damage or kinking.
Inspect all hardware and chain components for damage.
Inspect for any structural damage to product. (Return to factory for
repair or discard product if any damage is found.)
Inspect all nut and bolt assemblies to be certain none are loose.
Inspect for any missing parts.
Lubricate all pivot and slide together points with powder graphite to
prevent noise, wear, and rust.
Inspect entire product for any rust, corrosion, cracks, freezing,
excessive heat or rotting damage that may effect the safety of your
product. Discard any questionable product
Inspect entire product for any structural damage- pay close attention
to all weld locations. (Return to factory for repair or discard product if
any damage is found.)
Using correct wrenches inspect all nut & bolt assembly locations and
snug up any that may be loose. Be careful not to crush tubing when
tightening!
Inspect and check operation of all cables, cable ends, cord, rope,
webbing, and strap or chain assemblies. Replace with factory new
any item or assembly that shows signs of wear, damage, kinking, or
functions incorrectly.
Inspect seat. Replace any seat with factory new that shows signs of
structural damage or wear.
Inspect all hardware for wear or damage, also be sure you have no
missing parts.
Never modify your stand in any way by making repairs, replacing
parts, or altering adding or attaching anything to it except if explicitly
authorized in writing by the manufacturer.
4 
Check for parts online at
www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5

1/4-20 x 2-1/4" bolts
steel washers
side rails
st.
ree blade frame
locknuts
foot platform flat bars
1/4-20 x 1-1/2" bolts
1/4-20 x2-1/4" bolts
2-step ladder
w/stabilizer
bar mount
mesh foot platform
locknuts
Figure 7
Operator's Manual
IrC,no i llanW t
S ia 00
fr
Milers  Ed
V
Ond-Mantadde Stands
iEMBLY INSTRUCTIONS (RE622)
Tools needed - two 7/16" wrenches
IMPORTANT ASSEMBLY TIP. DO NOT TIGHTEN NUT& BOLT COMBINATIONS
COMPLETELY UNTIL ALL PARTS ARE ASSEMBLED TOGETHER! FINGER TIGHT-
EN PLUS ONE TURN OF A WRENCH ONLY! THIS WILL TEMPORARILY HOLD THE
LOCK NUT ON THE BOLT WHILE HELPING ALIGNMENT OF ALL PARTS! AFTER
ALL PARTS ARE ASSEMBLED TOGETHER, ALL NUT AND BOLT COMBINATIONS
MUST BE COMPLETELY TIGHTENED.
Attach the foot platform (1ML61), mesh side up, to the 2-step ladder section
w/ stabilizer bar mount (5L64) using (2) provided 1/4-20 x 2-1/4" bolts and
locknuts.
SEE FIGURE 1. DO NOT
tighten all nut & bolt assemblies
completely!
NOTE: Mesh surface should be on top with squared ends of platform
closest to ladder.
Attach the foot platform flat bars (AL7)to the foot platform and to the inside
of top ladder section side rails using (4) provided 1/4-20 x 1-1/2" bolts and
locknuts. SEE FIGURE 1.
Attach sling seat (48066) to assembled top sitting section by sliding each
side rail through webbing loops of seat (3 on each side of seat).5eat should
be orientated with seat straps on bottom side of seat for comfort.
NOTE:
Always have all three seat loops on each side of seat at-
tached to
the side rails of assembled top sitting section.
Attach the tree blade frame (51_67) to the side rails (5L69) using (4) provided
1/4-20 x 2-1/4" bolts, locknuts and steel washers,
SEE FIGURE 2. You must
low tighten all nut & bolt assemblies. Be sure not to over tighten or
rush tubing when tightening!
Sections are assembled on the ground in the following order. bottom section
(5L62 ladder); second section (5L62 ladder); third section (5L63 ladder with
stabilizer bar mount); fourth section (assembled 51_64 ladder with foot
platform); top section (assembled top sitting section).
SEE FINISHED 13'
PACK-N-STACK LADDER LINE ART.
A WARNING
FOOT PLATFORM AND SITTING SECTION MUST ALWAYS
FACE THE SAME DIRECTION, TOWARDS THE TREE.
Figure 2
5
Check for parts online at
www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5

spring lock pins
stabilizer bar
extension tube
'
<stabilizer bar
spring lock pins
Figure 4
Figure 5
Operator's Manual
Rivers Edge One-Man Ladder Stands
nth all sections assembled together on ground, secure all sections together
using (8) provided spring lock pins. Handle of spring lock pin must be put
to the outside of ladder side rails. SEE FIGURE 3.
a. Attach the stabilizer bar extension tube (1ML23) to the third ladder section
mounting bracket using (1) provided spring lock pin.
SEE FIGURE 4.
b. Slide the stabilizer bar (L29) into the extension tube and attach the two
pieces together using (1) provided spring lock pin. Spring lock pin must go
through both the extension tube and the stabilizer bar at appropriate hole
to achieve desired distance from tree. Adjustment in length may be needed
when ladder is uprighted later in instructions.
SEE FIGURE 4.
a.Tie one end of the provided 9' rope to the link welded onto the stabilizer
bar, just in front of the tree hugger.
Be sure your double knot is secure.
SEE FIGURES.
b.Tie one end of each of the provided 15' ropes to the square tube side rails
and tree blade frame, just in front of the welded on tree blade.
Be sure your
double knots are secure. SEE FIGURES.
Figure 3
6 
Check for parts online at
www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5

Figure 113: Unstacked View
Operator's Manual
re s „.1 1 1blarC i ,,S*F CD C
a
M iters  One-Man Ladde
Stands
.622 BACKPACKING STRAP
ATTACHMENT INSTRUCTIONS
Stack metal components of the ladder
AS SHOWN IN
FIGURE 1A AND 1B.
Lay stabilizer with extension tube along side of stacked ladder.
Wrap the provided ladder ratchet strap around the stacked frame.
Hook the two "S"-hooks together and ratchet tight.This will se-
curely hold all ladder components together.
Attach backpacking straps (48067) on packed ladder. Fold strap
in half. Feed folded strap through foot platform mesh and around
platform frame OR around the ladder rung located directly under-
neath the foot platform. Feed the two loose ends of strap through
folded loop and pull tight forming a cinch knot.
SEE FIGURES 2A
AND 2B.
Feed the two loose ends of straps around bottom group
of ladder rungs and secure with provided tri-slide buckles.
SEE FIGURE 2C.
Secureall laddersections and stabilizer bar togetherwith your ratchetstrap.
Figure IA: Stacked View
ha
Figure 2A: Attaching the straps
Figure 26: Pulling the straps tight
Figure 2C: Attaching
straps to bottom
Check for parts online at
www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5

7

fourth section-
third section
15' tie-off ropes
top section
. 4 ---- ratchet strap
9' stabilizer bar rope
stabilizer bar
extension tube
second section
spring lock pins
bottom section
Operator's Manual
Rivers Edge One-Man Ladder Stands
FINISHED PACK-N-STACK"m LADDER
8 
Check for parts online at
www.huntriversedge.com or
call 800-450-EDGE (3343) M-F 8-5

Operator's Manual
ItWets Ed Ond-Mantadddr Stands
)DER PARTS (RE622)
NO EXTENSIONS AVAILABLE FOR THIS MODEL
NEVER MODIFY OR EXCEED ORIGINAL STATED USE HEIGHT!
LADDER PARTS LIST (RE622)
KEY a PART a
DESCRIPTION
QTY.
1 4824013
BOLT, HHCS GR5 BLK 1/4-20 X 1-1/2"
4
2 48271B
BOLT, HHCS GR5 BLK 1/4-20 X 2-1/4"
6
3
48752B
NUT, FLANGED NYLOCK 1/4-20
10
4 63281
SNAP PIN, 1/4 X 1-3/4, ROUNDED
RETAINER
10
5 1ML23
SUPPORT TUBE, STABILIZER
1
6
1ML61
FOOT PLATFORM
1
7 AL7
SIDE SUPPORT, FOOT PLATFORM
2
8 L29
STABILIZER BAR, 18"
1
9
5L62
SWEDGED LADDER, 38"
2
10
5L63
SWEDGED LADDER WNAM, 38"
1
11 51.64
SWEDGED LADDER WNAM, 38"
1
12
SL67
TREE BLADE, LADDER
1
13
SL69
SIDE RAIL
2
14 482618
WASHER BLK 1/4"
4
ITEMS BELOW NOT SHOWN
--
48415
RATCHET STRAP
1
—
48155
FULL BODY HARNESS (FAS)
1
-- 48691
TIE-OFF ROPE KIT (INCLUDES TWO 15'
ROPES AND ONE 9' ROPE)
2
- 48066
SEAT, W/STIFFENER, SLING
1
- 48800
DVDTREESTAND SAFETY
1
Maximum Height -12' 3" to seat
Maximum Field Rating -300 lbs.
Tree Diameter Range -12" to 20"
Check for parts online at www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5

9

front platform
1/4-20 x 2" bolt
steel washers
locknuts
rear platform
1/4-20 x 2-1/4" bolts
\\*.
steel

Ej
washers
Figure 2
N
locknuts
rear platform
flat support
braces
platform suppo t rail
right
armrest
1/4-20 x 3" bolts
ladder side rails
1/4-20 x
2-1/4" bolts
.
„.
..t.t..
t. . ..:
*:
: L
.14
,
• 7
1
.:1 7::
:
:
".1
.a. - .nsi.
- .. 1
;a
;CS
AN.:
1
"••••or k
.tik,
:41.,... \
4 . 0 .1, - ..... eii"._lbs. .6........•
41, -
"Pkibr' .
..lar"-‘111%, INC
•••...
. 1 V
left
armrest
1/4-20 x 2"
bolts
steel washers
1/4-20 x 2" bolt
locknuts
Operator's Manual
Rivers Edges One-Man Ladder Stands
ir
EMBLY INSTRUCTIONS (RE627)
Tools needed — two 7/16" wrenches, one 9/16" wrench
IMPORTANT ASSEMBLY
TIP.
Do not tighten any nut and bolt combinations
completely until all parts are assembled together! Finger tighten plus one
turn of a wrench only! This will temporarily hold the lock nut on the bolt while
helping alignment of all parts! After all parts are assembled together, all nut
& bolt combinations must be completely tightened.
Attach the front platform (410050) and the rear platform (410058)
together using (2) provided 1/4-20 x 2" bolts, locknuts and steel
washers.
SEE FIGURE 1. DO NOT tighten all nut and bolt assem-
blies completely!
NOTE: Mesh surface of foot platforms should
be on top.
Attach the platform support rails (410055) to the bottom of as-
sembled foot platforms using (8) provided 1/4-20 x 2-1/4" bolts,
locknuts and steel washers.
SEE FIGURE 2.
Attach the platform flat support braces (1ML40) to the rear plat-
form and platform support rails using (4) provided 1/4-20 x 1-1/2"
bolts and locknuts.
SEE FIGURE 2.
Attach the front of the ladder side rails (410053) to the front plat-
form using (2) provided 1/4-20 x 2" bolts (2), locknuts (4) and steel
washers. SEE FIGURE 3.
atach the left armrest (410062L), right armrest (410062R) and (2)
backrest mounts (410082) to the previously assembled ladder side
rails and platform support rails using (2) provided 1/4-20 x 2" bolts,
(4) 1/4-20 x 2-1/4" bolts, (2) 1/4-20 x 3" bolts, (8) locknuts and (8)
steel washers.
SEE FIGURE 3.
rt g are I
backrest mounts
Figure 3
Check for parts online at
www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5
10

ladder side rails
tree blade
1
1/4-20x
2-1/4 bolts
steel washers
locknuts
steel
washers
nylon
spacers
fabric rail mounts
locknuts
1/4-20 x 1-1/4" bolts
front seat spacer assembly
1/4-20x 1-1/4" bolt
locknut
Operator's Manual
IrCJIN/ErC.,5*
.
ECIICIE
.
linters 
One-NlantaddeStands
kttach the tree blade (410056) to the ladder side rails using (4)
provided 1/4-20 x 2-1/4" bolts, locknuts and steel washers.
SEE
FIGURE 4.
Attach footrest (410061) to ladder side rails using (2) provided
1/4-20 x 2-3/4" bolts, locknuts, steel washers and nylon spacers.
SEE FIGURE 5.
a. Position the pre-assembled mesh seat/fabric rail mounts (360018)
upside down on a sturdy, hard surface. Spread the rear of fabric rail
mounts apart and insert the rear seat spacer weldment (410122).Tem-
porarily insert (2)1/420 x 2-1/4"bolts and locknuts. SEE
FIGURE 6a.
NOTE: Locknuts will need to be removed in order to
attached
finished seat to treestand later in assembly instructions.
Remove the loose 1/4-20
x 1-1/4" bolt and nut from the locking
hole of factory assembled front seat spacer assembly (410112).
DO NOT remove the factory tightened pivot bolt.
Set bolt and
nut off to the side for use in step 8c.
Spread the front (bent end) of fabric rail mounts apart. Take the
front seat spacer assembly (410112) and position angle brackets
near holes in fabric rail mounts. SEE FIGURE 6b.
Push the front
seat spacer assembly downward into its widest position to spread
seat apart and hold in place. Insert (2) provided 1/4-20 x 1-1/4"
bolts through the fabric rail mounts and the angle brackets of
front seat spacer assembly; secure with locknuts. While continuing
to hold seat spacer in place, re-insert (1) provided 1/4-20 x 1-1/4"
olt through the locking hole of front seat spacer assembly and
,ecure with locknut.
SEE FIGURE 6c
Be sure that all four angle
brackets (two on rear seat spacer and two on front seat spacer) are
fully cradling the fabric rail mounts. This locking action is a tight
fit by design in order to apply the correct amount of tension on
the mesh seat.
You must now securely tighten the (3)1/4-20 x
1-1/4" bolts and locknuts on the front seat spacer assembly.
Figures
1/4-20 x 2-1/4" bolts
Figure 6o
Figure 6b
front seat spacer assembly
Figure 6c
11
Check for parts online at
www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5

shooting rail
shooting
/ rail 1-pipes
/
1/4-20 x 2-1/4" bolts
locknuts
" 4 " ---- -locknuts
bolt-on
ladder step
i I I •

.1 b
. ' t 
4.1241 Z
t 
A 0 r
4 Ct.":
3, 1 Z S'
M t "
.1 k itti :V
4
2 ft i
t: Ve
• • 0, 11.
•
.4
6 4 . I LIZ;
 • la ‘ Z " : „. !St, • .)
• •  17 • • .7"
I
I •  •  •
„11.  • •  • 1 • I.
1/4-20 x
1-1/2" bolts
1/4-20 x
2-1/4" bolts
flared rails
steel washers
mesh backrest
3/8-16 nut
3/8" lock washer
backrest spacer
1/4-20 x 1-1/2"
bolts
retaining bar
locknuts
plastic stiffening
rods
Operator's Manual
Rivers Edge' One-Man Ladder Stands
.emove the locknuts from the (2)1/420 x 2-1/4" bolts that were previ-
ously attached to the rear of the seat assembly. Continue by attaching
the seat assembly to the ladder side rails using (2) provided 1/4-20 x
2-1/4" bolts, locknuts and nylon washers.
SEE FIGURE 7. Make sure
all (4) angle brackets are fully cradling fabric rails.
NOTE: Mesh seat is not depicted in drawing so hardware can be visible.
10. Insert the shooting rail 1-pipes (410113) into the shooting rail front
(410065) and secure together using (2) provided 1/4-20 x 1-1/4"
bolts and locknuts.
SEE FIGURE 8.
1/4-20 x 1-1/4" bolt
Figure 8
Insert the two side rails into the flared rails (410054). Secure using
(2) provided 1/4-20 x 1-1/2" bolts, locknuts and steel washers.
SEE
FIGURE 9.
Attach the bolt-on ladder step (410034) to the front side of flared
rails using (2) provided 1/4-20 x 2-1/4" bolts, locknuts and steel
washers.
SEE FIGURE 9.
Attach the mesh backrest assembly (360021) and the (2) retaining
bars (410081) to the backrest mounts using (6) provided 1/4-20 x
1-1/2" bolts and locknuts.
SEE FIGURE 10. The mesh backrest must
wrap around the front side of backrest mounts and the plastic stiff-
ening rod located in the sewn sleeve on each side of the backrest
MUST be positioned behind the backrest retainer bars to act as a
stop and prevent the backrest from pulling out during use. All bolts
MUST go through the backrest retainer bars, the holes provided in
)e backrest and the backrest mounts.
SEE FIGURE 10. Temporary
iemoval of the backrest mount tube from the rest of the assembled
ladder top may be necessary to attach the mesh backrest. If this is
needed, re-attach backrest mount tubes with mesh backrest to the
ladder top assembly.
seat assembly

nylon washers
Figure 9
Figure 70
Check for parts online at
www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5
12

spring lock pins
support braces
1/4-20 x 1-1/2" bolts
locknuts
shooting
rail
Artv
04:14CAW
t-1*.tc•i'a k
-Vi v
. 4
44 "NzAIW•Neh
ia ltF
oait
hli at i e
kii.%irtNi:
N ifAtk;
-Z .
)*
ilk * ft:1r 916.-it.
'111. 
miniel•Polav,
-
kyil l
t*-1"N4I i
rtZt
'Mr' •
Operator's Manual
Ir 11ECJINVE.,S*ECIPOla
t
RiVers  OnNi
etab taddor Stands
Thread the non-locking 3/8-16 nut onto the threaded end of
spacer rod all the way to the bottom of threads and slide 3/8" lock
washer on. Insert the threaded end of spacer rod through either
backrest mount tube far enough to be able to insert the opposite
end of spacer rod (end with welded-on washer) into opposite
backrest mount tube. Thread 3/8-16 nut back against mount tube.
Using a 9/16" wrench, tighten nut until mesh backrest becomes
taut.
SEE FIGURE 10. You must now tighten all nut and bolt
assemblies. Be sure not to over tighten or crush tubing when
tightening!
Sections are assembled on the ground in the following order; bot-
tom section (410066 3-step ladder); second section (410068 3-step
ladder with stabilizer bar mount); third section (4100693-step
ladder w/ mounting holes); top section (assembled top platform
section).
SEE FINISHED 17' OASIS LADDER.
With all sections assembled together on ground, secure all sec-
tions together using (6) provided spring lock pins. Handle of
spring lock pin must be put to the outside of ladder side rails.
SEE FIGURE 11.
Attach the (2) support braces (410024) to the inside of platform
support rails and outside of top ladder section w/ mounting holes
using (4) provided 1/4-20 x 1-1/2" bolts and locknuts.
SEE FIGURE
12. Tighten securely. Be sure not to over tighten or crush tub-
ing when tightening!
. Attach the removable shooting rail by setting rail down over
studs provided on armrests.
SEE FIGURE 13. Lubrication is rec-
ommended to prevent binding and noise.
Attach the (2) provided 9"and (1) provided 47" camo foam pads
to the armrests and shooting rail by wrapping around tubing and
attaching Velcro together.
Attach foam padded seat bumpers (48102) to bottom side of
front seat spacer assembly. Surface must be clean and at room
temperature to assure proper adhesion.
Figure 11
Figure 12
Figure 13
Check for parts online at
www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5

13

stabilizer bar
spring lock pins
stabilzier bar extension tube
third
section
second
section
9' stabilizer
bar rope
stabilizer bar
stabilizer bar
extension tube
ratchet strap
top section
15' tie-off
ropes
bottom section
spring
lock
pins
Operator's Manual
Rivers Edge° One-Man Ladder Stands
I. Attach the stabilizer bar extension tube (1ML23) to the second
ladder section mounting bracket using (1) provided spring lock
pin. SEE FIGURE 14.
b. Slide the stabilizer bar (L17) into the extension tube and attach
the two pieces together using (1) provided spring lock pin. Spring
lock pin must go through both the extension tube and stabilizer
bar at appropriate hole to achieve desired distance from tree. Ad-
justment in length may be needed when ladder is uprighted later
in instructions. SEE FIGURE 14.
20. a. Tie one end of the provided 9' rope to the link welded onto the
stabilizer bar, just in front of the tree hugger. Be sure your double
knot Is secure. SEE FIGURE 15.
b.Tie one end of each of the provided 15' ropes to the square tube
of tree blade frame, just in front of the tree blades. Be sure your
double knots are secure. SEE FIGURE 15.
Figure 74
Figure 15
Finished OasisTM Ladder
Check for parts online at
www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5
14

627 PARTS EXPLOSION
34
Operator's Manual
ff - CjeVair . l r S
vers 
One-Man Ladder Stands
Check for parts online at
www.huntriversedge.com or call 800-450-EDGE (3343) M-F 8-5

15

Operator's Manual
Rivers Edge One-Man Ladder Stands
627 PARTS LIST
NO EXTENSIONS AVAILABLE FOR THIS MODEL.
NEVER MODIFY OR EXCEED ORIGINAL STATED USE HEIGHT!
KEY # PART #
DESCRIPTION
60
1 10347
SPACER NYLON 1/4 X 1 X 1/2 2
2 1ML23 TUBE, STABILIZER, SUPPORT
1
3 1ML40
BRACE, SUPPORT FLAT, TIMBER
LADDERS
2
4 410024 BRACE SUPPORT 35.69"
2
5 410034
STEP LADDER 17" 1
6 410050
WELDMENT PLATFORM FRONT 20" X 15" 1
7 410053 RAIL SIDE LADDER
2
8
410054 RAIL SIDE FLARED LADDER 2
9 410055
RAIL PLATFORM SUPPORT 2
10
410056 WELDMENT, TREE BLADE LADDER
1
11 410058 WELDMENT PLATFORM REAR 20"X 15"
1
12 410061
FTS FOOTREST LADDER 1
13 410062L
WELDMENT ARMREST LEFT
1
14 410062R WELDMENT ARMREST RIGHT
1
15 410065
WELDMENT FTS SHOOTING RAIL
1
16
410066 WELDMENT LADDER 3 STEP
1
17 410068
WELDMENT LADDER W/MOUNT 3 STEP
1
18
410069 WELDMENT LADDER W/HOLES 3 STEP
1
19
410081 STRIP FABRIC MOUNT
2
20 410082
FTS MOUNT BACKREST
2
21 410112 ASSEMBLY SEAT SPACER FRONT
1
22 410113 FTS J PIPE SHOOTING RAIL
2
23 410118
WELDMENT SPACER BACKREST
1
24 410122
WELDMENT SEAT SPACER REAR
1
KEY # PART #
DESCRIPTION
QTY.
25 48153B BOLT 1 / 4
-20 X 2 HHCS GR5 BLK ZN 6
26 48240B
BOLT 1/4-20 X 1-1/2 HHCS GR5 BLK ZN 16
27
48261B WASHER FLAT 1/4" BLACK
32
28 48271B
BOLT 1/4-20 X 2-1/4 HHCS GR5 BLK ZN
20
29 48280B
BOLT 1/4-20 X 3 HHCS GR5 BLK ZN
2
30
48752B
NUT 1/4-20 HFNYLK BLK ZN 50
31 63281
SNAP PIN, 1/4 X 1-3/4, ROUNDED
RETAINER
8
32 67540B
BOLT 1/4-20 X 2-3/4 HHCS GR5 BLK ZN
2
33
8909B BOLT 1/4-20 X 1- 1 / 4
HHCS GR5 BLK ZN 4
34
L17 WELDMENT, STABILIZER BAR
1
35 WN516
WASHER, 5/16", BLACK NYLON 2
36 10755
NUT 3/8-16 HEX BLK ZINC
1
37 719
WASHER 3/8 SPRING LOCK ZINC
1
ITEMS NOT SHOWN
360018
ASSEMBLY SEAT OASIS
1
360021
ASSEMBLY BACKREST OASIS
1
- 48415
RATCHET STRAP
1
-
48155 FULL BODY HARNESS (FAS)
1
— 48736
CAMO SLEEVE W/FOAM 9"
2
--
48912 CAMO SLEEVE W/FOAM 47"
1
--
48691
TIE-OFF ROPE KIT (INCLUDES TWO 15'
ROPES AND ONE 9' ROPE)
1
48102 PAD, BUMPER SEAT
2
48800
DVDTREESTAND SAFETY
1
Maximum Height - 17' 2" to shooting rail
Maximum Field Rating -300 lbs.
Tree Diameter Range -12" to 20"
16

Check for parts online at www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5

rear platform
flat support
braces
platform support rails
1/4-20x 2-1/4" bolts
steel \\*
washers ,
'
Ito 
il".,
-ilik
4„, im
aral,t1,1/4.444A46.
,, t
S
itoliravill"
;;;;;;Ik
\lilk
\ZI;i1t;:41:161 - -
illtVikt\111‘‘Slilik
S1/4•7411. \ "1.11011L,47021.9.
, 61
I I
SH
"
trna 14.1* ZONA
i t
li I
1.4\21%
I
N
It4t
V
" 61.. .Y
11.).
-.1.1"11.1"itajtall41•AtIk*\716.1P
N '
-
lik\iik \

1:40.4."‘ alikliti,..
'1 / 4
11116
.*Q
1
.9e
,
Figure 2
1/4-20 x
1-1/2" bolts
front platform
1/4-20 x 2" bolts
steel washers
. r9W
-4e.s4
o > e 4
* <96 >
<><9
,41* e 
e
e e4
e
e 4
e
e t s e `s S
locknuts
locknuts
1/4-20 x 2" bolts
Figure 3
backrest mounts
7 7
1/420 x 3" bolts
locknuts
left
armrest
right armrest
ladder side rails
e -
-- -'-`1%.
4....-
•••••
-- ..k.'"
, ‘.."...
:
vo," -... - 
,,Z
i t-ths.
. I.
''..,... lit

"' 4 %.
. . . . . 2
-•;k . " -, rikir
uk . N.., 4 • 1 / 4
".41 . "..... 4 "
4
...„..............z.........,.....,__,..,...._
.....
.....
............ .. ...........,........
.......t.... ........ .... ,..t.,,...... .....
tiZ.‘1 , 7:
11 ,Z.
,jaw 4
' N.C.:47%S' , •
, -....N.
steel washers
Operator's Manual
irCFI/a IFC...S t
itF COG la
ITRre rs  Ont-Man
Ladder Stands
IIP
SEMBLY INSTRUCTIONS (RE628)
Tools needed - two 7/16" wrenches, one 9/16" wrench
IMPORTANT ASSEMBLY TIP. Do not tighten any nut and bolt combinations
completely until all parts are assembled together! Finger tighten plus one
turn of a wrench only! This will temporarily hold the lock nut on the bolt
while helping alignment of all parts! After all parts are assembled together,
all nut & bolt combinations must be completely tightened.
Attach the front platform (410083) and the rear platform (410086)
together using (2) provided 1/4-20 x 2" bolts, locknuts and steel
washers.
SEE FIGURE 1. DO NOT tighten all nut and bolt assem-
blies completely!
NOTE: Mesh surface of foot platforms should be on top.
Attach the platform support rails (410055) to the bottom of as-
sembled foot platforms using (8) provided 1/4-20 x 2-1/4" bolts,
locknuts and steel washers. SEE FIGURE 2.
Attach the platform flat bars (1ML40) to the rear platform and
platform support rails using (4) provided 1/4-20 x 1-1/2" bolts and
locknuts. SEE FIGURE 2.
4. Attach the front of the ladder side rails (410053) to the front plat-
form using (2) provided 1/4-20 x 2" bolts (2), locknuts (4) and steel
washers. SEE FIGURE 3.
ttach the left armrest (410062L), right armrest (410062R) and (2)
backrest mounts (410082) to the previously assembled ladder side
rails and platform support rails using (2) provided 1/4-20 x 2" bolts,
(4) 1/4-20 x 2-1/4" bolts, (2) 1/4-20 x 3" bolts, (8) locknuts and (8)
steel washers.
SEE FIGURE 3.
rear platform
17
Check for parts online at
www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5

steel
washers
nylon
spacers
locknuts
rear seat spacer
fabric rail mounts
Figure 6o
front seat spacer assembly
1/4-20x 1-1/4" bolts
Figure 66
1/4-20x 1-1/4" bolt
locknut
et"
74 .\7
4 " ,,
gt
••: .
:"..,w...
1
...• <
.....7.44:•“Ii:Q•Clii,
1
".• N.
**,
Nli,..N.P.11ZY liV
.
N.litZ
b
.. 400t
.. s..N.N.N......
....‘ ,
44.. . 4. .5
%.
-. .. 1 " ...."411.
7 .
,
•14. .. ••• mi., ,
. 7
..:".
1:
A.....-Ztzt
rk
,.., -"•,...
,
V". ....
1.2...• ••‘
.."L
'Illi. ',. ... \ Z"
.
"%:......
14...-.. t .'"I
Z E. i.
. ...... ..i
1.4
11“...
I
,
................ N.,: ,
- No s.. ." ,
w .
.." .................. 4,
1 %,..c.Z . V ,
..,, 
.....
'
SW.: lik 41•:
..
.,411....7.1i..
1. 7e ,
.... .IIL.,
•
3.
,
..4..."It .
I
..
ladder side rails
locknuts
it
[vox
2-1/4" bolts
steel washers
tree blade
Operator's Manual
Rivers Edge* One-Man Ladder Stands
(ttach the tree blade (410090) to the ladder side rails using (4) pro-
- vided 1/4-20 x 2-1/4" bolts, locknuts and steel washers.
SEE FIGURE 4.
Attach footrest (410092) to ladder side rails using (2) provided 1/4-20 x
2-3/4"bolts, locknuts, steel washers and nylon spacers.
SEE FIGURES.
a. Position the pre-assembled mesh seat/fabric rail mounts (360019)
upside down on a sturdy, hard surface. Spread the rear of fabric rail
mounts apart and insert the rear seat spacer weldment (410127).Tem-
porarily insert (2) 1/4-20 x 2-1/4" bolts and locknuts.
SEE FIGURE 6a.
NOTE:
Locknuts will need to be removed in order to attach fin-
ished seat to treestand later In assembly instructions.
Figures
b. Remove the loose 1/4-20 x 1-1/4" bolt and nut from the locking
hole of factory assembled front seat spacer assembly (410115).
DO
NOT remove the factory tightened pivot bolt.
Set bolt and nut
off to the side for use in step 8c.
locknuts
1/4-20 x 2-1/4" bolts
c. Spread the front (bent end) of fabric rail mounts apart. Take the
front seat spacer assembly (410115) and position angle brackets
near holes in fabric rail mounts.
SEE FIGURE 6b.
Push the front
seat spacer assembly downward into its widest position to spread
seat apart and hold in place. Insert (2) provided 1/4-20x 1-1/4"
bolts through the fabric rail mounts and the angle brackets of
front seat spacer assembly; secure with locknuts. While continuing
to hold seat spacer in place, re-insert (1) provided 1/4-20 x 1-1/4"
bolt through the locking hole of front seat spacer assembly and
secure with locknut. SEE FIGURE 6c.
Be sure that all four angle
rackets (two on rear seat spacer and two on front seat spacer) are
ally cradling the fabric rail mounts. This locking action is a tight
fit by design in order to apply the correct amount of tension on
the mesh seat.
You must now securely tighten the (3)1 /4-20 x
1-1/4" bolts and locknuts on the front
seat spacer assembly.
nyure 4
front seat spacer assembly
Figure 6c
Check for parts online at
www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5
18

1/4-20 x 2-1/4" bolts
nylon washers
shooting rail
Figure 8
shooting rail J-pipes
1/4_20 x 1-1/4"
bolts
locknuts
locknuts
flared rails
steel washers
bolt-on
ladder step ,,-
1/4-20x 1-1/2"
bolts
1/4-20 x
2-1/4" bolt
-..zrzZ"V&I
..:,-......,....
1 %
- t
 .. ... ._..,,
....."2• 1-,. .."Vt.Z.t
.
.;;*.',„..*;,....„- Q..,.
...z....4:zz, ,
-1.1. ...Z....Z.
, -..., ......,.. ... . -
. , ,. ...t . 1 1. - -.:-
70 .,. a  ... .,..........", z,,:.
.. .. - -
...,.....
4..
,,,..
..., „.. .
..z.
mesh backrest
3/8-16 nut
3/8" lock washer
plastic stiffening
rods
retaining bars
backrest spacer
1/4-20 x 1-1/2" bolts
locknuts
Operators Manual
laILDGE
Biters 
E Oner-Mah Laddet Stands
'c 
s
emove the locknuts from the (2)1/4-20 x 2- 1 / 4
" bolts that were previ-
ously attached to the rear of the seat assembly. Continue by attaching
the seat assembly to the ladder side rails using (2) provided 1/4-20 x
2-1/4"bolts, locknuts and nylon washers.
SEE FIGURE 7. Make sure all
(4) angle brackets are fully cradling fabric rails.
Insert the shooting rail 1-pipes (410113) into the shooting rail front
(410093) and secure together using (2) provided 1/4-20 x 1- 1 / 4
"
bolts and locknuts. SEE FIGURE 8.
Insert the two side rails into the flared rails (410089). Secure using
(2) provided 1/4-20 x 1-1/2" bolts, locknuts and steel washers.
SEE
FIGURE 9.
Attach the bolt-on ladder step (410034) to the front side of flared
rails using (2) provided 1/4-20 x 2-1/4" bolts, locknuts and steel
washers.
SEE FIGURE 9.
Attach the mesh backrest (360022) and the (2) retaining bars (410081)
to the backrest mounts using (6) provided 1/4-20 x 1-1/2" bolts and
locknuts. SEE FIGURE 10.The
mesh backrest must wrap around the
front side of backrest mounts and the plastic stiffening rod located
in the sewn sleeve on each side of the backrest MUST be positioned
behind the backrest retainer bars to act as a stop and prevent the
backrest from pulling out during use. All bolts MUST go through the
backrest retainer bars, the holes provided in the backrest and the
backrest mounts.
SEE FIGURE 10.
Temporary removal of the backrest
mount tube from the rest of the assembled ladder top may be neces-
iry to attach the mesh backrest. If this is needed, re-attach backrest
.lount tubes with mesh backrest to the ladder top assembly.
14.Thread the non-locking 3/8-16 nut onto the threaded end of spacer
rod all the way to the bottom of threads and slide 3/8" lock washer
on. Insert the threaded end of spacer rod through either backrest
mount tube far enough to be able to insert the opposite end of
spacer rod (end with welded-on washer) into opposite backrest
mount tube.Thread 3/8-16 nut back against mount tube. Using a
9/16" wrench, tighten nut until mesh backrest becomes taut.
SEE
FIGURE 10. You must now tighten all nut and bolt assemblies.
Be sure not to over tighten or crush tubing when tightening!
seat assembly
Figure ?
Figure 9
Figure 10
19
Check for parts online at
www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5

support braces
shooting
rail
-7,.4 . c
...7r.z“,,:t....
A -1V.7‘.11), , --- -
.., ...?
, ..1, -
..,........t
,....„..N.‘ ..: '
,4 1.1 1
?"•:..,`" ,,
.... •,.."....
1 %.
....
„
t
n... '.....
••
•••..
—
b••••
.40 0
.,...
1 •,..
....
..,,,„., -.ft...7
1'W 
' ‘.11. 
4
* ... ,• •••\
..,1 1. -,' .1 .11.4.. ....*
4.1. ‘ 'Ilk
.. .'ilr
I, "..4•••• ..k....: - III. -... .. \ ...."., . 7 .1 .,‘ . 1 .
1?":14•T".'.
..".441."'S,11:1" 4,""Melt....
'VII. 
,
lk,Z.V.1 4 .1 . .1116,..,' /,..,.. ,S. - - ti.... '1.
1.1.a.mlor.k., •••,..Ip.. .
4 .1
,1 •7r
. ' ,
." '
' ..... %Z
i t: r
a .1.7%.;,:k
i t: • .
." %). .." .\ • ,
. : ,r-
-". • ,
..t.....". ..T.k.,
4
. 1,‘ V i.
N•16,...h.*:.;, 'al.
-'"*".•••
NI....
, Ils
Operator's Manual
Rivers Edge One-Man Ladder Stands
<Cons are assembled on the ground in the following order; bot-
tom section (4100663-step ladder); second section (410068 3-step
ladder with stabilizer bar mount); third section (410069 3-step
ladder w/ mounting holes); top section (assembled top platform
section). SEE FINISHED 17'1UMBO JACK LADDER.
16.With all sections assembled together on ground, secure all sec-
tions together using (6) provided spring lock pins. Handle of
spring lock pin must be put to the outside of ladder side rails. SEE
FIGURE 11.
17.Attach the (2) support braces (410024) to the inside of platform
support rails and outside of top ladder section w/ mounting holes
using (4) provided 1/4-20 x 1-1/2" bolts and locknuts.
SEE FIGURE
12. Tighten securely. Be sure not to over tighten or crush tub-
ing when tightening!
18.a. Attach the removable shooting rail by setting rail down over
studs provided on armrests
SEE FIGURE 13. Lubrication is rec-
ommended to prevent binding and noise.
Attach the (2) provided 9" and (1) provided 54" camo foam pads
to the armrests and shooting rail by wrapping around tubing and
attaching Velcro together.
Attach foam-padded seat bumpers (48102) to bottom side of
front seat spacer assembly. Surface must be clean and at room
temperature for proper adhesion.
spring lock pins
Figure 11
Figure 12
Figure 13
20 
Check for parts online at
www.huntriversedge.com
or call 800-450-EDGE (3343) M-F 8-5