ROADWORX Multi Electric Stand User manual

Multi Electric Stand
electric height-adjustable stand
User manual

Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: [phone]
E-mail: [email protected]
Internet: www.thomann.de
29.09.2020, ID: 491963

Table of contents
1 General information.............................................................................................................. 5
1.1 Further information........................................................................................................ 5
1.2 Notational conventions................................................................................................. 5
1.3 Symbols and signal words........................................................................................... 6
2 Safety instructions................................................................................................................. 7
3 Features.................................................................................................................................... 10
4 Assembly.................................................................................................................................. 11
5 Operating elements............................................................................................................ 19
6 Operating................................................................................................................................. 20
7 Technical specications.................................................................................................... 21
8 Protecting the environment........................................................................................... 22
Table of contents
Multi Electric Stand 3
electric height-adjustable stand

4Multi Electric Stand
electric height-adjustable stand

1 General information
This user manual contains important information on the safe operation of the device.
Read and follow all safety notes and all instructions. Save this manual for future refer‐
ence. Make sure that it is available to all persons using this device. If you sell the
device to another user, be sure that they also receive this manual.
Our products and user manuals are subject to a process of continuous development.
We therefore reserve the right to make changes without notice. Please refer to the
latest version of the user manual which is ready for download under
www.thomann.de.
1.1 Further information
On our website (www.thomann.de) you will nd lots of further information and
details on the following points:
Download This manual is also available as PDF le for you to download.
Keyword search Use the search function in the electronic version to nd the
topics of interest for you quickly.
Online guides Our online guides provide detailed information on technical
basics and terms.
Personal
consultation
For personal consultation please contact our
technical hotline.
Service If you have any problems with the device the
customer service will gladly assist you.
1.2 Notational conventions
This manual uses the following notational conventions:
The letterings for connectors and controls are marked by square brackets and italics.
Examples: [VOLUME] control, [Mono] button.
Texts and values displayed on the device are marked by quotation marks and italics.
Examples: ‘24ch’ , ‘OFF’ .
Letterings
Displays
General information
Multi Electric Stand 5
electric height-adjustable stand

The individual steps of an instruction are numbered consecutively. The result of a
step is indented and highlighted by an arrow.
Example:
1. Switch on the device.
2. Press [Auto].
ðAutomatic operation is started.
3. Switch o the device.
1.3 Symbols and signal words
In this section you will nd an overview of the meaning of symbols and signal words
that are used in this manual.
Signal word Meaning
DANGER! This combination of symbol and signal word indicates
an immediate dangerous situation that will result in
death or serious injury if it is not avoided.
CAUTION! This combination of symbol and signal word indicates
a possible dangerous situation that can result in minor
injury if it is not avoided.
NOTICE! This combination of symbol and signal word indicates
a possible dangerous situation that can result in mate‐
rial and environmental damage if it is not avoided.
Warning signs Type of danger
Warning – high-voltage.
Warning – danger zone.
Instructions
General information
6Multi Electric Stand
electric height-adjustable stand

2 Safety instructions
This device is intended for use as multifunctional base for stable xing and height-
adjustable installation of keyboards, synthesizers, stage pianos, etc. Use the product
only as described in this user manual. Any other use or use under other operating
conditions is considered to be improper and may result in personal injury or property
damage. No liability will be assumed for damages resulting from improper use.
This device may be used only by persons with sucient physical, sensorial, and intel‐
lectual abilities and having corresponding knowledge and experience. Other persons
may use this device only if they are supervised or instructed by a person who is
responsible for their safety.
Intended use
Safety instructions
Multi Electric Stand 7
electric height-adjustable stand

DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and
are not within reach of babies and young children. Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the
like) from the unit. They could swallow the pieces and choke!
Never let children unattended use electrical devices.
DANGER!
Electric shock caused by short-circuit
Always use proper ready-made insulated mains cabling (power cord)
with a protective contact plug. Do not modify the mains cable or the
plug. Failure to do so could result in electric shock/death or re. If in
doubt, seek advice from a registered electrician.
DANGER!
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present.
Never remove any covers.
There are no user-serviceable parts inside.
Do not use the device if covers, protectors or optical components are
missing or damaged.
CAUTION!
Danger of tipping due to overload
In case of overload, the stand may tip over and cause injuries and prop‐
erty damage.
Never exceed the maximum load capacity specied for the stand.
CAUTION!
Danger of tipping on unsuitable ground
If placed on soft or uneven ground, the stand may overturn and cause
injuries and property damage.
Place the stand on at and solid surfaces only.
Safety
Safety instructions
8Multi Electric Stand
electric height-adjustable stand

NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage,
never expose the device to any liquid or moisture. Avoid direct sunlight,
heavy dirt, and strong vibrations.
Only operate the device within the ambient conditions specied in the
chapter ‘Technical specications’ of this user manual. Avoid heavy tem‐
perature uctuations and do not switch the device on immediately after
it was exposed to temperature uctuations (for example after transport
at low outside temperatures).
Dust and dirt inside can damage the unit. When operated in harmful
ambient conditions (dust, smoke, nicotine, fog, etc.), the unit should be
maintained by qualied service personnel at regular intervals to prevent
overheating and other malfunction.
NOTICE!
Possible staining
The plasticiser contained in the rubber feet of this product may possibly
react with the coating of your parquet, linoleum, laminate or PVC oor
and after some time cause permanent dark stains.
In case of doubt, do not put the rubber feet directly on the oor, but use
felt-pad oor protectors or a carpet.
Safety instructions
Multi Electric Stand 9
electric height-adjustable stand

3 Features
Special characteristics:
nElectric height-adjustable stand for keyboards, synthesizers, stage pianos, mixers,
studio equipment, etc.
nSteplessly height-adjustable from 61 cm up to 126 cm
nFour heights freely storable
nAdjustable feet to compensate for oor unevenness
nMany adding-on accessories (available separately)
nMaximum load capacity: 150 kg
Features
10 Multi Electric Stand
electric height-adjustable stand

4 Assembly
When assembling the stand, use felt-pad oor protectors or a carpet in
order not to damage the coating of your parquet, linoleum, laminate or PVC
oor.
Open the package and make sure before assembling that the entire scope of delivery
is present, as posted here.
1 Control panel
2 Control panel holder
3 4 × slide screw
4 4 × round nut
5 8 × Allen screw M6×25
6 2 × tube
7 2 × standing column
8 Motor holder
9 14 × Allen screw M6×10
10 4 × adhesive cable tie
11 Motor
12 2 × cable of the standing column
13 Cable of the control panel
14 2 × foot
15 Power cable
16 2 × crossbar
17 4 × Allen screw M6×40
18 4 × adhesive foam pad
19 2 × angle piece
20 2 × Allen key
1. Set up the stand near a power wall outlet.
2. Proceed according to the illustrations and only use the supplied screws. Using
other screws could result in a reduced stability of the stand.
Assembly
Multi Electric Stand 11
electric height-adjustable stand

3. First attach the control panel (1) to the control panel holder (2). Use the four
supplied slide screws (3) and the four round nuts (4) and hand-tighten them.
4. Place the tubes (6) and standing columns (7) as illustrated. Attach the mounted
control panel holder with two Allen screws M6×25 (5) to the tube (6) and to the
standing column (7) using the Allen key (20). Attach the tube and the standing
column on the other side following the same procedure.
Assembly
12 Multi Electric Stand
electric height-adjustable stand

5. Attach the motor holder (8) with four Allen screws M6×10 (9) to both tubes (6)
using the Allen key (20).
6. Attach two adhesive cable ties (10) in the illustrated position to properly install
the cable of the control panel.
Assembly
Multi Electric Stand 13
electric height-adjustable stand

7. Slide the motor (11) in the holder (8) and connect the cables of the standing
columns (12) and the cable of the control panel (13) to the motor.
8. Attach the feet (14) with four Allen screws M6×10 each (9) to the standing col‐
umns (7).
Assembly
14 Multi Electric Stand
electric height-adjustable stand

9. Attach two adhesive cable ties (10) in the illustrated position to properly install
the power cable (15). Connect the power cable (15) to the motor (11).
Ensure that the power cable is not installed too tight in the cable ties.
The cable should be able to move while adjusting the height.
Assembly
Multi Electric Stand 15
electric height-adjustable stand

10. Turn the stand over and put it onto the feet.
Attach the crossbars (16) at the desired position to both tubes (6) with two
Allen screws M6×40 each (17) using the Allen key (20).
11. Attach two adhesive foam pads (18) to each crossbar (16) at the desired posi‐
tions.
Assembly
16 Multi Electric Stand
electric height-adjustable stand

12. Attach the angle pieces (19) if desired with one Allen screw M6×10 each (9) to
the crossbars (16).
Alternatively, you can attach the devices to be mounted on the stand with a
3/8” cylinder head screw each (not included in the scope of delivery) using the
Allen key (20).
Align the control panel (1) as desired and tighten the slide screws (3) and the
round nuts (4).
Assembly
Multi Electric Stand 17
electric height-adjustable stand

13. Align the adjustable feet to compensate for the oor unevenness.
The assembled stand should now look like the following illustration:
Assembly
18 Multi Electric Stand
electric height-adjustable stand

5 Operating elements
1 Display
2[1] | [2] | [3] | [4]
Number buttons for storing and selecting a set height
3[S]
Buttons for storing a set height
4|
Buttons for setting the height
Control panel
Operating elements
Multi Electric Stand 19
electric height-adjustable stand

6 Operating
Unpack and check carefully there is no transportation damage before using the unit.
Keep the equipment packaging. To fully protect the product against vibration, dust
and moisture during transportation or storage use the original packaging or your
own packaging material suitable for transport or storage, respectively.
1. Hold down or to set a desired height from 61 cm up to 126 cm. The motor
starts to work and moves the stand in the desired position.
ðThe display shows the set height (e.g. ‘090’ for the set height of 90 cm).
2. Release or to apply the setting.
ðThe motor stops.
3. Press [S] and then one of the buttons [1], [2], [3] or [4] to store the set height to
one of the number buttons.
4. Press one of the buttons [1], [2], [3] or [4] at any time to move the stand to the
stored height.
ðThe motor moves the stand automatically in the stored position.
Height setting and storing
Operating
20 Multi Electric Stand
electric height-adjustable stand