Rockler 66877 User manual

Review full instructions prior to use for important safety information.
Always check Rockler.com to confirm that you are using the most recent version of instructions for your product.
Rock-Steady Shop Stand Corner Stand Assembly Instructions
Effective September 2021

2
This product is designed only for specific applications as defined in the instructions and should not be modified or used for any
manner not described in these instructions. Use only recommended accessories. Before using the Rock-Steady Shop Stand
Corner Stand: READ, UNDERSTAND and FOLLOW ALL INSTRUCTIONS AND SAFETY WARNINGS. KEEP THESE
INSTRUCTIONS READILY AVAILABLE FOR FUTURE REFERENCE.
GENERAL SAFETY WARNINGS
>Always confirm that you are using the most recent version of
the Instructions and safety warnings for your product (see the
Instructions link on the product page at Rockler.com).
>Before using another tool with this product, always read,
understand and follow the instructions and safety warnings
in the owner’s manual for that tool. If you do not have the
owner’s manual, obtain one from the tool’s manufacturer
before using it with this product.
>Before using any chemical with this product, always read,
understand and follow all safety warnings and guidelines in
the manufacturer’s Safety Data Sheet (SDS; formerly called
“MSDS”), especially regarding:
• How to safely use the chemical, including potential hazards
and recommended first aid measures;
• Personal safety equipment required to safely use the
chemical (e.g. gloves, eye protection, mask/respirator, etc.);
• Proper and safe handling, storage and disposal of
the chemical.
>Before using this product, review and verify that all tools to be
used with it have safety equipment installed and are in proper
working order as defined by the tool’s owner’s manual.
>Do not use this product until you have read and are
confident you understand:
• Install the Levelers (p. 3);
• Stand Assembly (pp. 3 - 4).
>The user assumes all risk and responsibility for the proper and
safe use of this product and for ensuring product suitability for
the intended application.
>It is the sole responsibility of the purchaser of this product to
ensure that any anyone you allow to use this product reads
and complies with all instructions and safety precautions
outlined in this manual prior to use.
>Follow all standard shop safety practices, including:
• Keep children and bystanders away from the tool
operating area;
• Do NOT use power tools in explosive environments, or in
the presence of flammable liquids, fumes or dust;
• TURN OFF AND UNPLUG all power tools BEFORE
making any adjustments or changing accessories;
• Remain alert and use good judgment. Do not use this
product if you are in any way impaired by medications,
alcohol, drugs or fatigue;
• Keep your work area well lit and clean;
• Dress appropriately. Secure loose clothing, remove all
jewelry and tie up long hair before using this product;
• ALWAYS wear safety glasses, hearing protection
and respiratory protection that complies with
NIOSH/OSHA/ANSI safety standards;
• Use dust collection tools and dust face masks to
reduce exposure to dust;
• Use safety equipment such as featherboards, push
sticks and push blocks, etc., when appropriate;
• Maintain proper footing at all times and do not overreach;
• Do NOT force woodworking tools.
>These warnings and instructions do NOT represent the total
of all information available regarding tool safety, use and
technique. Always seek out opportunities to learn more
and improve your skills and knowledge.
Drilling, sawing, sanding or machining wood
products can expose you to wood dust, a substance known
to the State of California to cause cancer. Avoid inhaling
wood dust or use a dust mask or other safeguards for
personal protection. For more information go to
www.P65Warnings.ca.gov/wood.
Danger indicates a hazardous situation that, if not avoided, will result in death or serious injury.
Warning indicates a hazardous situation that, if not avoided, could result in death or serious injury.
Caution indicates a hazardous situation that, if not avoided, may result in minor or moderate injury
or property damage.
Notice indicates important or helpful information and/or user tips.
BP1219

3
Install the Levelers
1. Unscrew and remove the top hex nut from each of the
Leveling Feet.
2. Insert the threaded post of a Leveling Foot up through
the base of each of the 90° Legs and 22.5° Legs.
3. Thread the hex nut back on each Leveling Foot and use
a 3/4" wrench to tighten. Fig. 1.
4. If you need to adjust the Leveling Feet after the Steel Stand
is fully assembled, loosen the Top Hex Nut and lower the
Bottom Hex Nut. Adjust the Middle Hex Nut until the
Leveling Foot is correctly positioned. Then tighten the
Top Hex Nut and raise the Bottom Hex Nut until it’s
tight against the Middle Hex Nut.
Stand Assembly
1. Start with one of the back corner sections. Lay out two 90°
Legs with two 32" Stretchers between them.
2. Make sure the 32" Stretchers are oriented so the mitered top
flanges are facing up. Position them on the inside faces of the
90° Legs and align the square holes in the Stretchers with
those in the Legs, at top and bottom.
3. Connect the 32" Stretchers to the 90° Legs with a 5/16"-18
Carriage Bolt, Washer and 5/16"-18 Nut in each square hole,
starting with the top holes. The Carriage Bolts should
installed from the outside face of the Legs so the round
heads are facing out. Before fully tightening the Nuts,
use a square to make sure that the Stretchers and Legs
are joined at 90°.
4. Attach the other two 32" Stretchers to the remaining 90°
Legs with two 5/16"-18 Carriage Bolts, Washers and
5/16"-18 Nuts at each intersection, making sure that the
Stretchers are on the inside of the Leg and oriented so
the mitered top flanges are facing up.
5. Attach that assembly to one of the Legs of the first assembly
with two 5/16"-18 Carriage Bolts, Washers and 5/16"-18 Nuts
at each intersection. Again, before fully tightening the nuts,
use a square to make sure that the Stretchers and Legs are
joined at 90°.
Fig. 1
Corner Sub-Assembly
Leveling Foot
Top Hex Nut
Leg
Washer
5/16"-18 Nut
5/16"-18 Carriage Bolt
32" Stretchers
90° Leg

4
Check Rockler.com for updates. If you have further questions, please
contact our Technical Support Department at 1-800-260-9663
or [e-mail]
6. With the rear corner section assembled, lay out the two
22.5° Legs with the two Front Stretchers in between, making
sure that the Stretchers are on the inside of the Legs and
oriented so the mitered top flanges are facing up.
7. Connect the Front Stretchers to the 22.5° Legs with a
5/16"-18 Carriage Bolt, Washer and 5/16"-18 Nut in each
square hole, starting with the top holes. Before fully
tightening the nuts, use a square to make sure that
the Stretchers and Legs are joined at 90°.
8. Attach the front section from Step 7 to the rear corner
section with two 16" Stretchers on each side, making sure
that the Stretchers are oriented so the mitered top flanges
are facing up. Connect the 16" Stretchers to the 22.5° Legs
of the front section and the 90° Legs (1) of the rear corner
sections with a 5/16"-18 Carriage Bolt, Washer and 5/16"-18
Nut in each square hole. Again, before fully tightening the
nuts, use a square to make sure that the Stretchers and
Legs are joined at 90°.
9. Mount the top of your choice and, if desired, a shelf,
using the mounting holes in the mitered flanges of the
Stretchers. (Mounting hardware for top and
shelf not included.)
10. If necessary, adjust the Leveling Feet so the stand sits
solidly on the floor.
11. Apply the Rockler sticker to one of the Front Stretchers.
We recommend centering it on the lower Front Stretcher.
Distributed by Rockler Companies, Inc.
4365 Willow Dr. Medina, MN 55340
66877 66915
Rev 0921
1-800-279-4441
www.rockler.com
Front Sub-Assembly
Washer
5/16"-18 Nut
5/16"-18 Carriage Bolt
Front Stretcher16" or 20" Stretcher
22.5° Leg