Roper Rhodes T171102 Parts list manual

Customer Service
Tel: [phone] Fax: [phone]
Email: [email protected]
www.roperrhodes.co.uk
Roper Rhodes Limited
Brassmill Lane Trading Estate, Bath, BA1 3JF
REF: PL.RR.T171102 | 07.15 V2
Sign Basin Mixer / Tall Basin Mixer /
Mini Basin Mixer
Installation & aftercare instructions
Please retain for future reference
Product code
T171102
Basin Mixer Product code
T175002
Tall Basin Mixer
Product code
T176102
Mini Basin Mixer

We have complete confidence in this Roper Rhodes product and as such it is offered with a 10-year guarantee against defects in
manufacture. This tap must be fitted by a competent installer. If in doubt seek advice from a qualified professional. The guarantee requires
that this product be used in the manner for which it was intended and that it is installed & maintained in accordance with the fitting
instructions and local water bylaws. The guarantee covers products in domestic use only. The guarantee is invalidated should the tap be
damaged by water borne debris. Make sure that supply pipes are clear of any debris prior to installation, this is particularly important on new
plumbing installations. In the unlikely event that this product should fail during the guarantee period we will either replace the faulty part or
the complete unit as appropriate. Tap cartridges are subject to a 1-year guarantee. This guarantee covers damage against reasonable wear
and tear in use only. It does not cover damage incurred during installation, misuse or inappropriate maintenance. We recommend that the
cartridge is regularly cleaned in hard water areas to prevent lime scale build-up. Replacement cartridges are available to purchase by
contacting the Roper Rhodes Customer Service team. Failure to follow the terms outlined above will invalidate this guarantee. Proof of
purchase will be required to validate any guarantee claims.
10-YEAR GUARANTEE
REF: PL.RR.T171102 | 07.15 V2
MIN
25mm
 
Click Waste Installation:
Aftercare Instructions
Installation Procedure:
Fit the upper rubber washer to the waste body and
insert the assembly into the basin waste hole as
shown below.
1Firmly screw the fixing nut tight to the basin. Care
however must be taken not to over tighten the waste
and crack the basin. Check to ensure there are no
leaks when the basin is filled with water. Silicone
sealant may be applied to the underside of the upper
washer for an additional seal if necessary.
3
On the underside, fit the additional rubber washer
and fixing nut.
2
Waste body
Upper Rubber Washer
Basin
Lower Rubber Washer
Waste Fixing Nut
Prior to installation flush out the pipe work to
remove debris and then ensure that the water
supply is turned off.
Refer to diagram and check that all components
are present.
1
2
Fit the flexible tail hoses to the basin mixer/ mini
basin mixer body using an appropriate spanner,
making sure that you do not over tighten.
3
Connect the water supply to the flexible hoses.
Hot supply should always be connected to the
left hose (Flexible hose 1 in the diagram).
6
Fully open mixer on both hot & cold sides &
allow water to run for approximately one minute
to further flush the system.
7Check all connections to ensure there are no
leaks.
Basin Mixer / Tall Basin Mixer: Fit the mixer
body to the basin using the supplied securing
collar,. DO NOT overtighten as this may damage
the basin. Remember to install the rubber insert
between the basin mixer body and the basin.
or
Mini Basin Mixer: . Fit the mixer body to the
basin using the supplied washers, and fixing
ring in the order indicated in the drawing. Screw
the fixing bolts through the fixing ring to secure.
DO NOT over-tighten as this may damage the
basin. Remember to install the rubber o-ring
between the mixer body & the basin.
4
5
Whilst this item has a high quality durable finish, it should nevertheless be treated with care. Surfaces should be cleaned using
only a soft damp cloth and clean water & dried using a soft cotton cloth. Bath cleaning products, even non-scratch ones could
damage the finished surface.
Flexible Hose 1
Flexible Hose 2
Rubber
Insert
Securing
Collar
OR
Washer
Basin Mixer / Tall Basin Mixer Mini Basin Mixer
Fixing Ring
O-ring
Fixing Bolts
Washers
Basin