RTscan RTX200A User manual

RTX200A/B
Scanners User Manual
1
1

Table of Contents
Video introduction and User Guide:............................................................................................. 2
Installation and Disassemble................................................................................................................ 3
RTX200A Installation.....................................................................................................................3
RTX200B Installation.....................................................................................................................4
Chapter I Product Parameters...............................................................................................................5
Appearance parameters................................................................................................................ 5
RTX200B................................................................................................................................. 5
RTX200A................................................................................................................................. 6
Size parameters.............................................................................................................................. 7
Reading parameters.......................................................................................................................7
Device parameters......................................................................................................................... 8
Chapter II Wiring instructions.............................................................................................................. 9
Pin definitions.................................................................................................................................9
USB interface................................................................................................................................ 10
RT232 Serial Port Wiring............................................................................................................ 10
TTL Wiring....................................................................................................................................11
Chapter III RTX200_WIFI Connection & Configuration Guide......................................................... 11
1. Hardware connecting...............................................................................................................11
2. RTX200 settings....................................................................................................................... 12
A. Run ConfigTool.exe, from “Offline Device” area, select TX........................................... 12
B. Work mode settings.........................................................................................................12
C. NET settings......................................................................................................................13
D. Scan settings.....................................................................................................................15
3. Communication protocol......................................................................................................... 16
A. TCP.................................................................................................................................... 17
B. TCP protocol..................................................................................................................... 18
C. HTTP/HTTPS.................................................................................................................... 18
D. HTTP/HTTPS protocol.................................................................................................... 19
Chapter ⅣApplication configuration................................................................................................ 20
USB Communication Setting........................................................................................................20
RS232 Serial port Communication Setting.................................................................................21
TTL Communication Setting........................................................................................................22
Chapter V. Explanation of the Output Format................................................................................... 23
Chapter VI Common Faults and Troubleshooting Methods............................................................. 23
Video introduction and User Guide:
https://youtu.be/seTemau-ExA

Installation and Disassemble
RTX200A Installation
Buckle design
Outside embedding
1 second installation
Recommended opening size: 67.5*88mm

RTX200B Installation
Chassis
Installation instructions 1
Nut column
Fixing screw
Chassis
Installation instructions 2
Nut column
Fixing screw
Installation instructions 1
Nut column diameter does not exceed 5.8mm, through the scanner to fix the round hole outside diameter.
The diameter of the screw part of the fixing screw is not more than 4mm, tighten the nut from the back
through the hole inside diameter
When the plate thickness is 2mm, the maximum nut height is 3.5mm
When the plate thickness is 1.5mm, the maximum height of the welded nut on the steel plate is 4mm
Installation instructions 2:
Screw column diameter not more than 4mm is okay, directly through the scanner to fix the round hole
internal diameter

Chapter I Product Parameters
Appearance parameters
RTX200B
Picture 1-1

RTX200A

Size parameters
Table 1-1 Appearance parameters
Reading parameters
Table 1-2 Reading parameters
RTX series QR Code Reading parameters
Image Sensor
300,000 pixel CMOS (640*480)
light source
Led diffuse lighting (white lighting, red indicator)
Instruction
Buzzer, three blue LED status indicators, red LED indication
Identification code
QR Code, Data Matrix, EAN_13, EAN_8, RSS_14, CODE_39,
CODE_93, CODE_128, ITF, Code Bar, Inverse Code, Mirror
Code, etc.
Print contrast
≥ 25%
Reading accuracy
≥ 7mil
Reading speed
70ms/times
Field of view angle
Horizontal field of view 77° , vertical field of view 60°
Reading angle
Tilt ± 40° , deflection ± 30° , rotate 360°
Depth of field
0mm~55mm（15mil QR Code）
Parameter
RTX200B
RTX200A
Type
physical
95*84*48mm
95*70*48mm
dimension
Reading
59*46mm
59*46mm
window size
Installation
Embedded
External
method
installation
installation
Materials
ABS
ABS
67.5*88mm
67.5*88mm
Hole Size
Corner radius
Corner radius
4.27mm
4.27mm

Device parameters
Table 1-3 Specific parameters
Technical indicators
Specific parameters
Microprocessor
32-bit 1G CPU, high-speed DDR memory
Data interface
RS232 (9.6 ~ 115.2kbps), USB1.1 (HID-KBW,
HID-POS), custom HID (add USB development
interface, high-speed transmission)
Data line
RS232 data line (USB power supply interface + DB9 data
interface), USB cable, TTL line
Operating temperature
-20~70 degrees Celsius
Storage temperature
-40 to 80 degrees Celsius
Humidity
Relative humidity 0%~95%
Ambient light intensity
0~80,000LUX
Operating Voltage
Supports 5~15V wide voltage input
Working current
0.15A (5V) or 0.05A (15v)
Maximum power
0.75W
Consumption
Maintenance Requirements
Support remote maintenance and online upgrade
Materials
Body: Imported PC window: Tempered glass
Operating System
Supports Windows (xp.7.8.10), Linux, Android, Mac, etc.

Chapter II Wiring instructions
Pin definitions
Table 2-1
RTX200 external output interface is RJ45 crystal head, pin definition is as follows:
PIN#
Signal Name
I/O
Description
1
NC
NC
2
NC
NC
3
GND
-
Power ground
4
VCC
-
Power input
5
TX-232
Output
Serial 232 level output
6
RX-232
Input
Serial 232 level input
7
UART1_TXD_TTL
Output
TTLinterface XMIT
8
UART1_RXD_TTL
Input
TTLinterface RxDn
Table 2-2 wire sequence table

USB interface
The usage steps are as follows:
1. First connect the RJ45 plug of the data line with the scanner;
2. Connect the USB port on the other end of the cable to the PC (or control board).
Table 2-3 USB wiring
RT232 Serial Port Wiring
The usage steps are as follows:
1. Firstly, connect the RJ45 plug on the data line with the scanner;
2. Connect the RS232 interface on the data cable to the PC (or control board);
3. Then connect the USB port of the data cable to the 5V power supply, which can be the USB
port on the computer, or other USB ports that can provide 5V power supply;
4. After the power is turned on, the auxiliary lighting of the product will be turned on. After
hearing the “buzz” sound, the scanner will enter the working state.
Table 2-4 RS232 wiring

TTL Wiring
TTL interface
Please connect according to the TTL line sequence.
Table 2-5 TTL wiring
Please do remember the input power supply should be 3.3v, and can’t be more than 3.3v.
Chapter III RTX200_WIFI Connection & Configuration Guide
1. Hardware connecting
Use the USB to RJ45 cable to connect to the scanner (for power supply)

2. RTX200 settings
A. Run ConfigTool.exe, from “Offline Device” area, select TX
Click Next
B. Work mode settings
Work mode: Ordinary
Output: WIFI
WIFI/Ethernet/2G output: TCP

C. NET settings
Set the action after successfully reporting data (Optional)
SuccessAction: Flash lamp (Optional)
Set the action after failed to report data (Optional)
FailAction: Flash red (Optional)
Set the server address and port to which the data is uploaded (*Necessary)
Address: server address, IPV4, such as 192.168.4.1
Port num: server port, Range 0-65535

HeartSet
It is recommended to set heartSet when WIFI output is set to TCP, TCP protocol
Heart time: default 60s
Heart conter: content
The device will send Heart conter to the server at regular intervals after setting
IP mode setting
It is recommended to set to Dynamic IP to automatically assign IP addresses.
Dynamic IP: IP address is automatically assigned by router DHCP
Static IP: manually specify the IP address, when set to static IP, you must input the IP
address, Subnet mask, Gateway, the format is as follows:

WIFI configuration
D. Scan settings
Click “config code” to generate the configuration code, use the scanner scans the
configuration code (from computer screen directly) to complete the setting

For detailed usage of the configuration tool, please refer to "Configuration Tool User
Manual".
After the configuration is complete, the device automatically connects to the specified server,
and will upload the data after scanning the bar code
3. Communication protocol
As a client, the scanner can initiate HTTP or TCP/IP requests to the server and process the
response returned by the server. The interface specification is defined as follows
TCP/TCP protocol
The format of the requested TCP/IP server IP address is: xxx.xxx.xxx.xxx
The requested TCP/IP server port format is: 0-65535

HTTP/HTTPS
The requested HTTP server path format is: http://serveraddr:port/path
Among them:
serveraddr——The domain name or IP address of the server
port——The server port
path——The server path
The requested HTTP type is POST
A. TCP
The scanner sends the original scanned data to the server.
The server:

B. TCP protocol
The format of the content sent to the server is: vgdecoderesult=xxx&&devicenumber=xxx
Among them:
vgdecoderesult=xxx——Where xxx represents the decoded result string
devicenumber=xxx——Where xxx represents the scanner device number (can be set in the
main interface: Advanced -> Device num)
The format of the response is: code=xxxx&&desc=xxx
Among them:
code=xxxx——xxx indicates the server processing result code, 0000 indicates success, others
indicate errors
desc=xxx——xxx represents server processing description
For example:
Device->The server
vgdecoderesult=12345678&&devicenumber=0
The server->Device
code=0000&&desc=ok
C. HTTP/HTTPS
The HTTP packet format is as follows:
Device-The server
POST /test HTTP/1.1
Host: 192.168.4.1:8080
Accept: */*
Content-Type: text/html; charset=UTF-8
Content-Length: 7
abcdefg
Body content is the original data of the scanned code

D. HTTP/HTTPS protocol
The HTTP packet format is as follows:
Device-The server
POST /test HTTP/1.1
Host: 192.168.4.1:8080
Accept: */*
Content-Type: text/html; charset=UTF-8
Content-Length: 53
vgdecoderesult=12345678&&devicenumber=0&&otherparams=
The server->Device
HTTP/1.1 200 OK
Content-Type: text/plain;charset=utf-8
Content-Length: 9
code=0000
The content format is:
vgdecoderesult=xxx&&devicenumber=xxx
vgdecoderesult=xxx——Where xxx represents the decoded result string
devicenumber=xxx——Where xxx represents the scanner device number (can be set in the
main interface: Advanced -> Device num)
The format of the response is: code=xxxx
xxxx indicates the server processing result code, 0000 indicates success, others indicate errors

Chapter ⅣApplication configuration
USB Communication Setting
Connect the device directly to the computer through the USB cable. The device defaults to the
analog keyboard output. The output data will be show up where you put the cursor, as
shown below:
Table 4-1