Rugged CCTV Night Chaser 500 User manual

Night vision type vehicle
Intelligence PTZ camera
User‟s Manual
Pleased read the manual carefully before using the product

1
Contents
1. Attention -----------------------------------------------------------------2
2. Introduction -------------------------------------------------------------3
3. Specification -------------------------------------------------------------6
4. Explanation of Product
4.1Drawing--------------------------------------------------------------7
4.2 Installation------------------------------------------------------------7
4.3ID code Setting -------------------------------------------------------9
4.4Protocol Setting-------------------------------------------------------9
4.5Setting Baud Rate ---------------------------------------------------10
4.6Setting Protocol of zoom camera ----------------------------------11
4.7Explain of connecting-----------------------------------------------12
5. Operation-------------------------------------------------------------------13
6. Index Diagram of the Screen Menu ------------------------------------17
7. The Menu Setting ---------------------------------------------------------20
8. General Failure Analysis Table---------------------------------------- -29
9. Appendix Ⅰ---------------------------------------------------------------30

2
Notes for Attention
1. Read the manual carefully before installing the product..
2. Please do not dismount components inside the product to avoid
occurrence of trouble. There is no part inside the product, which
needs repair by customer himself.
3. Clean out dirt with special lens tissue if dust is stuck on the lens.
4. Do not aim the camera at the sun or very bright object, aim or
monitor bright and still object for a long time whether the power
supply of the camera is switched on or off.
5. Do not apply the product under the state exceeding limited
temperature, humidity or specifications of power supply.
6. Carefully use camera. Do not shock and strike it.
7. Please install the speed pan/tilt in the wall or horizontal. Do not be
bottom up.
8. Observe all electric safety standards in application and adopt
special power supply attached the product. RS-485 control signal
and video signal should be kept enough distance with the high
voltage devices and cables during the course of transmission, and
take protection measures such as anti-lightning and surging etc. if
necessary.

3
Introduction
Description of Functions
Intelligence heavy-duty Pan/Tilt is an all-in-one high-tech
monitoring product, which integrates high-definition color video
camera, universal gear change pan-tilt and multi-function decoder,
infrared LED, character list folds to add, alarm function. This
product furthest reduces the processes of connection an
installation between system reliability. Also the video camera is
very easy to install and maintain, has many features, such as
perfect shape, legerity and convenience, simple operation and etc.
1. Integrate multi-function decoder
a. Built-in decoder consists of multi-protocol and communications
protocol. Communication serial baud rate (2400~9600) is
adjustable. Using the simple finger-switch inside the device, the
products can be compatible with kinds of systems and has very
high commonality.
b. RS485 serial control, addresses of P/T is from 1~255
2. Integrate full-view rotary station
a. Horizontal 360°unlimited continuous rotation, pan speed is 100°/s
and Manual control speed can be adjusted from 0.1 ~60°per
second continuously；Vertical rotation range is -75°~85°Tilt speed
is 60°/s and manual control speed can be adjusted from 0.1
~40°per second continuously.
b. Low speed's circulating a steady and super and low voice, not film
oscillation
c.The realization is all-directions to keep watch on without the blind
spot, positioning accuracy to reach ±0. 1
3：High intelligence

4
a. Provides 128 preset points. power-off memory
b. Provide setting of scanning track and select scanning track
function.
c. Four groups of scanning tracks: Every group of scanning track
can set Max. 16 preset positions.
d. Limiting speed when Long focal distance. Can be quickly
accurate to search a target
4. Camera function: The actual function makes reference to the
camera module.
a. Focus：Draw near & Push far
b. Zoom ：Draw near & Push far
c. Backlight compensation：On & OFF
d. White Balance：When the display picture appears a color to
lose really, the customer can establish various mode through
a setting.
e. Min. illumination set：Under general circumstance the
camera work is in the automatic appearance, when the
illumination is lower than 1Lux, the camera will cut over
automatically Min. illumination can also adjust by manual
way.
f. Other faction of camera control by menu of system.
5. Alarm Input & Output
a. 4 Alarm input ，Normal Open, closing for alarm
b. 2 Alarm output，Normal Open, Normal Close Output
c. When the system identifies the alarm signal, the P/T and

5
camera will work immediately, and report the picture of alarm
district to main monitor.
6. Infrared System
a. The infrared system is normally under automatic control state.
The infrared lamp shall act followed by open/close of the low
illumination of the camera;
b. The open/close state of the infrared lamp can be changed by the
menu manually;
c. The default option on the menu of the infrared lamp is OFF.
Normally the system detects external illumination and
opens/closes the infrared lamp automatically. If the user changes
the option of the infrared lamp into ON, the infrared system is
changed into the manual control; if changing back into the
automatic control, the user should set the option on the menu of
the infrared at OFF.
7. Brush function.

6
3. Specification
Spec.
Power Supply
DC 12V /AC24V
Power consumption
30VA
Weight
6Kg
Installation
top mounted, wall mounted
Relative humidity
10-90%
Work temperature
-35℃~55℃
Waterproof Class
IP66
Faction
of P/T
Pan speed
100°max
Tilt speed
60°max
Preset position
128 preset potions
Tracks
4 Tracks
Scanning speed
0.5°～30°/s
IR
LED
IR LED
High Brightness LED 36pcs/18pcs
Infrared LED rang 80 meters
power consumes
6W/10W
IR LED CONTROL
Auto/ Manual control on menu
LED life
More than 20000 hours
Alarm
4 Input
Normal Open, closing for alarm
2 Output
Normal Open, Normal Close Output

7
4 Explanation of Product
4.1 Drawing1 （with brush ）
4.2 Drawing2（without brush）

8
4.3 Installation
Plain Base Installation
Steps of installation
1. Remove the bottom plate of the pan/tilt;
2. Set the corresponding information in accordance with the
schematic drawing of the dip-switch of addresses, protocols and
baud rates;
3. Install the bottom plate of the pan/tilt and take care of the tightness
of waterproof seal ring;
4. If vehicle used, first of all fix the Shock Bracket on the bottom of the
pan/tilt then fix the whole pan/tilt;
5. If the plain base is used, fix the pan/tilt onto the fixation hole of the
pan/tilt
6．Connect the output wires of the socket according to relative colors
on the schematic drawing and do not make wrong connections;
7. For the common pan/tilt, 10-core socket is used as the alarm

9
interface and detailed connection can be seen from the
description of colors of terminals.
4
4. .3 3 I ID D c co od de e s se et tt ti in ng g
The ID code setting of P/T set by 8 digital-switch, address of P/T is
from 1~255, about the Stir code of addresses 1~128, please see
the Appendix Ⅰ.
From DIP-8 to DIP-1 equal to an 8 digital binary systems DIP-8 is
the tallest, DIP-1 is lowest. The each "ON" appearance means 1,
the "OFF" appearance means 0.There is the parts of Stir code of
addresses .Setting as below picture
The Stir codes of addresses 129~255 set as binary system

10
4.4 Protocol Setting
The protocol of P/T set by the No.1, No.2 and No.3 of
BK2 switch, setting as below picture.
Common Baud Rate as below (bps) ：B01/9600 ；
ALEC/4800；VCL/4800；PelcoP/4800/9600；PelcoD/2400；
A01/4800；Santachi/9600。
4.5 Setting Baud Rate of P/T
Baud Rate setting of this P/T set by the No.4, No.5 of BK2.Setting as
below pictures.

11
4.6 SETTING PROTOCOL OF ZOOM CAMERA
Protocol of zoom camera setting by the No.6,No.7 and No.8
of BK2 switch ，Setting as below pictures.
Set protocol of YOKO zoom camera as the LG setting.
Note：
Before above setting, Must power off first.

12
4.7 Explain of connecting ：
Ａ．7-Core Input Terminal Ｂ．10-Core Input Terminal
4.71 Description of 7-Core Terminal：
Note：AC 24V power line is at a non-positive and negative
4.72 Description of 10-Core Terminal：
1．Alarm-1 in: Red 2．Alarm-2 in: Orange
3．Alarm-3 In: Yellow 4．Alarm-4 In: Green
5．NULL
6．Alarm In COM: Black 7．Alarm Out COM: White
8．NULL
9．Alarm NO OUT: Blue 10．Alarm NO OUT: Pink
4.73 Description of 10-Core Socks：
The 10-core socket is used for alarm system. If 10-core socket is
not inserted and there is no alarm system;
1．DC12V: Red + /AC24V 2．DC12V: GND Black-/AC24V
3．R- (communication-): Yellow 4．Null
5．R+ (communication+):Orange
6．V+: (VF+) 7．V-: (VF-)

13
5. OPERATION (Default protocol PELCO-D/2400)
The speed P/T can be controlled remotely horizontal and vertical movement. It is
used with a system controller, separately. It is controlled remotely from the
controller through a serial connection to the RS-485 connector using a
twisted-pair cable.
Conventional Function
1. Pan / Tilt Function
The pan function will move the camera on all horizontal planes, to surveillance
position. The tilt function will move the camera on a vertical plane, to surveillance
position. The speed is variable according to the angle of joystick.
2. Zoom Function
2.1 The filming range can be set using the zoom function.
Press TELE the LCD displays Zoom Tele
Press WIDE the LCD displays Zoom Wide
Note：The bigger zoom is，the slower of joystick „s speed is .
2.2 Iris Function
Normally，Focus is AUTO。
Focus level can be adjusted by pressing [NEAR] and [FAR]
Move the joystick, focus will be auto.
3. Preset Memory
The preset memory function will memories camera positions and zoom, focus, etc.
Setting up to 128 preset camera positions can be memorized. Later, you can
easily recall any of the preset camera positions by entering its corresponding

14
number, and the camera will move the memorized position with all the preset
settings.
3.1 To set a preset position
SET + N + ENTER
N: the number of preset position: 1~128
3.2 To call a preset position
When camera positions have been set, you can enter a memorized camera
position number.
Preset + N + ENTER
N: the number of preset position: 1~128
4. Delete a preset position
[PRESET]+ [N] + [OFF]
N: the number of preset position: 1~128
5. To call cruise tracks：
[PRESET]+32+[ENTER]
This command can call the No.1cruise tracks. It can scan preset points no.1 ~ 16.
[PRESET]+53+ [ENTER]
This command can call the No.2cruise tracks. It can scan preset points no.17 ~
31.
[PRESET]+49+ [ENTER]
This command can call the No.3cruise tracks. It can scan preset points no.33 ~
48.
[PRESET]+50+ [ENTER]
This command can call the No.1cruise tracks. It can scan preset points no.65 ~
80.
Note: If some points are not been set or delete, it will not scanning these points
when cruising. Resort 3 seconds in every preset point.

15
6．Setting scanning track
Method 1：
1. Setting begin scanning track point
[SET] + [51] + [ENTER]
Adjust the position of Speed P/T which you need.
2.Setting finish scanning track point：
[SET] + [52] + [ENTER]
Adjust the position of Speed P/T which you need.
3．Calling scanning：
[PRESET]+51+ [ENTER]
Note: Setting begins and finishes scanning track point first.
4．Stop scanning
[PRESET]+52+ [ENTER]
(Move Joystick also can stop scanning）
When Speed P/T scanning, default state following
a. Speed P/T scan between two points.
b. Scan “begin-point” and “end-point” and resort 3 seconds
c. If “begin-point” and “end-point” superpose, Speed P/T horizontal 360°rotation.
Method 2：
Call scanning
[AUTO]+ [ON]
The Speed P/T scanning 360 degree. Need not to set the preset
point
7. Brush function

16
1. Open the brush: [PRESET]+ 9 + [ENTER]
2. Close the brush [SET]+ 9 + [ENTER]
Note: Above operation use for our company’s suited keyboard by
example, detail operation do as your keyboard menu
Operation of camera
Note：Some cameras don’t support the above function of them.
(N)
Control object
The definition of key
PRESET+N+ENTER
SET+N+ENTER
54
Power supply
Come back Initial value
/
55
Backlight
compensation
ON
OFF
56
Min. illumination
ON
OFF
57
Menu/ Screen Display
ON
OFF
58
Digital Zoom
ON
OFF
59
Focus
AUTO
MANUAL
60
IRIS
AUTO
MANUAL
61
White Balance
AUTO
MANUAL
62
Static image
Image congeal
Normal image
63
Mirror image
Image mirror
Normal image
64
Color/black & white
Color
B/W

17
Power-off memory
Provide setting of scanning track and select scanning track function. Self-test can
allow to store track that user edits arbitrarily and information power-off memory.
6. Index Diagram of the Screen Menu

18
Index Diagram of the Screen Menu
This is the camera‟s OSD function, which include the menu while
opening and the menu while operating.
Open it, and see the start of image, the order of showing is:
Waiting for image
The image of system information
The information of checking itself
Horizontal Check OK
Vertical Check OK
Camera Check OK
Waiting…
Version : 1.35
Camera : Sony
Dome ID : 001
Protocol : PelcoD
Band Rate : 2400

19
The finished information of checking itself
The Menu Setting
● The major menu setting
After checking itself, please {[PRESET] +8+ [ENTER]}, then it
will show the image as the No.1-0-1:
→（Pic.1-1-1）
→（Pic.1-2-1）
→（Pic.1-3-1）
→（Pic.1-4-1）
→（Pic.1-5-1）
1-0-1 System information
On the menu of 1-0-1, turn up or down the rocker to point to system
info ( or click the up or down key of controlling system) , then turn right
to enter to system info( or click the right key of control system)
As per the image 1-1-1:
System Info
System Setup
Camera Control
Preset Control
Special Function
Factory Default
EXIT
Self test passed, you
can control the PTZ
now
Version : 1.35
Camera : Sony
Dome ID : 001
Protocol : PelcoD
Baud Rate: 2400
EXIT