Samaire SA493 User manual

INSTRUCTION
MANUAL
MODEL: SA493

1
Parts & Accessories- SA493
1. Canopy
2. Downrod Assembly
3. Coupling Cover
4. Motor Assembly
5. Blades
6. Light kit
7. Light kit cover
Item Qty
1
1
1
1
3
1
1
Blade Panel Screw x 7Expansion Screws x 1
Bolt x 1 Expansion Screws x 4
Downrod
Canopy
Blade
Connect Plate
Motor Assembly
Light Kit Plate
Light Kit Cover
Coupling Cover

2
SA493 Ceiling Fan
1
1
1
1
1
1
1
QTYDESCRIPTION
Lock Pin
R Pin
Nut
Screw and Washers
Downrod
Ball
Pin
Mounting Bracket
Motor 1
1
Coupling Cover
1
Canopy
2
Screw
1
1
1
1
R Pin
Screw and Washers
Nut
Bracket
1
Lock Pin
Screw and Washers 6
1
Top Housing
Metal Plate 1
Screw 2
Socket 2
1
Light kit cover
3
Blade
Washers 3
Screw and Washers 6
1
5
Screw and Washers
Connect Plate 1
1
Light kit plate
Washers 1
Nut
Washers
Washers
Washers
Plate 1
1
1
1
3
Screw and Washers

3
Installation Instruction
IMPORTANT:SWITCH OFF THE ELECTRICAL MAINS AT THE MAIN CIRCUIT BREAKER
FUSE BOX.
Step 1 - Remove the clevis pin,nut and bolt on the rubber pulley. Assemble the canopy and the
Coupling Cover on the downrod.
Step 2 - Route the safety wire, yellow/green, orange, blue and brown wires through the downrod.
Fix the downrod to the shaft with bolt and nut and tighten them firmly the insert the clevis pin.
Downrod
Canopy
Coupling Cover
ORANGE (LIGHT)
Washer
R Pin
Nut
Bolt
Safety Wire
Blue (N)
Brown (L)
Motor
GREEN/YELLOW

4
Installation Instruction
Step 3 -
The hanger bracket should be screwed on to a
firm flat surface. the fixing location must be able
to withstand twenty times the static weight of the fan.
If you have any doubts as to the ability of your
intended fixing location to be able to withstand
this loading.
Step 4 -
Connect the blue,brown & orange wire to the house's supply wire. Diagram shows a complete
assembly of the ceiling fan of the ceiling fan with safety wire mounted on the hook.
GREEN/YELLOW
BLUE(N)
BROWN(L)
ORANGE(LIGHT)
SAFETY WIRE
CONCRETE CEILING
Orange(Light)
HOUSE’S SUPPLY
CONCRETE CEILING
Orange(Light)
CONCRETE CEILING

5
Installation Instruction
Step 6 -Install the bulbs into the socket (Max. 18W/socket)
Step 5 -
Important: Assemble the blades only after the ceiling fan is mounted on the bracket.
5A) Remove the screws at the motor and fix the blade with the piece to the motor using
these screws.
5B) Connect the blue and orange wire from the light kit to the fan motor wire, align the
slotted holes on the light kit and tighten back the 3 screws.
5A 5B
Light kit

6
Installation Instruction
Step 7 - Fix the lamp shade to the fitter plate and twist in.
Electrical Connection
THERMAL LINK
18W(MAX) E27 18W(MAX) E27
UL3321 / AWG 16 (Blue)
UL3321 / AWG 16 (Blue)
UL3321 / AWG 16 (Orange) UL3321 / AWG 16 (Orange)
NOTE: LIGHT BULB USED SHALL NOT EXCEED 18W AND E27 TYPE ONLY.
Earth Wire
UL1015/AGW 18
(YELLOW/GREEN)

7
１２４５ ｍｍ
49"
４１７．６ ｍｍ
２６８．５ ｍｍ

8
14. The current carrying wires must be protected by an insulated sleeve and that the wires (inclusive of the
sleeve) shall not be subjected to stress.
15. The external earthing conductor should be such that when failure of the suspension system occur,
current-carrying conductors become taut before the earthing conductor.
16. After fan being installed, safety cord should not be longer than the earthing conductor, should failure of the
suspension system occur, the supporting of the fan must not rely on the earthing conductor.
17. Location of the earthing terminal in the fan assembly should be such that should any part of the suspension
system fall off , the body of the fan assembly shall effectively earthed.
18. When installing light bulbs, turn off the electrical mains. Light bulb used shall not exceed 18W and
E27 type only.
so that the blades are