SAMMI Information Systems SmartTablet User manual

CONFIDENTIAL Page 1 2004/8/20
I
In nd du us st tr ri ia al l T Ta ab bl le et t
S
Sm ma ar rt tT Ta ab bl le et t
U
Us se er r’ ’s s M Ma an nu ua al l
S
SA AM MM MI I I In nf fo or rm ma at ti io on n S Sy ys st te em ms s C Co o. ., , L Lt td d. .

CONFIDENTIAL Page 2 2004/8/20
FCC (Federal communiction commission)
This device was tested for typical body-worn operations. The antenna(s) used for
this transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. To comply with FCC RF exposure requirements third-party
belt-clips, holsters, and similar accessories used by this device should not contain
any metallic components. Body worn accessories that do not meet these requirements
may not comply with FCC RF exposure requirements and should be avoided. The
FCC had granted an Equipment Authorization for this model device with all reported
SAR levels evaluated as in compliance with the FCC RF exposure guidelines.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment is FCC Class B product and it complies with FCC Part 15 standard. This
equipment must be installed and operated in accordance with provided instructions. End-users
and installers must be provided with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance.
CONTENTS:
 SmartTablet Web Pad.
 Stylus Pen.
 Protective Cover.(Applicable to the case of Mass Production).

CONFIDENTIAL Page 3 2004/8/20
 AC/DC Adaptor/Battery Charger.
 Lithium-Ion Rechargeable Battery Pack
 User’s Manuals.

CONFIDENTIAL Page 4 2004/8/20
DECLARATION OF CONFORMITY
Per FCC Part 2 Section 2. 1077(a)
hereby declares that the product
Product Name: Industrial Tablet PC
Model Number: Smart Tablet
Conforms to the following specifications:
FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a),
Class B Digital Device
Supplementary Information:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the authority to operate equipment.

CONFIDENTIAL Page 5 2004/8/20
THINGS TO BE CAREFUL:
 Do not disassemble SmartTablet at any time.
 Do not use AC/DC adapter/battery charger other than the one with the package.
 Keep away from any object with magnetic field.
 Keep away from the fire flame.
 Do not leave SmartTablet exposed to direct sunlight.
 Keep battery separately if SmartTablet is not in use for a long period time.
 Do not touch the screen with any sharp object.
 Connect the USB Camera only to the USB port on the top of SmartTablet. Do not use
the USB port on the right side of SmartTablet for camera at any time.
 Always save the files into HDD and back them up occasionally to the safe place.
 USB port on the right side of SmartTablet can be used for USB interfaced devices such as
USB keyboard, USB mouse, USB FDD, USB Smart Cable, USB CD-ROM and etc.
(Note that USB CD-ROM needs to have its own power supply)
In case of problem and for any other inquiry, please contact below personnel:
E-mail: mailto:[e-mail]
Phone: [phone]

CONFIDENTIAL Page 6 2004/8/20
CONTENTS
Chapter 1. APPEARANCE
Chapter 2. KEY FUNCTIONS
Chapter 3. SETTING UP SmartTablet HARDWARES
1. Installing the battery pack .
2. Connecting to the power.
3. Charging Time.
4. Handle the Battery Pack With Cautions.
Chapter 4. USING AND SETTING SmartTablet
1. Power on.
2. Power off.
3. Rotate Button Setting.
4. Media Player 6.4 Setting.
5. Display setting
6. Touch Screen.
7. One Touch Setting
8. Stylus Pen.
9. Installing PCMCIA Card.
10. Connecting Monitor.
11. Master Volume Setting
12. PS/2 Device
13. Network Setting
14. To Input URL easily in Windows Internet Explorer for Windows
ME
15. Hibernation
16. To execute OnScreen Keyboard
Chapter 5. APPLICATIONS OF WIRELESS LAN CARD
1. Wireless network driver installation
2. Access to Wireless network

CONFIDENTIAL Page 7 2004/8/20
3. Power Management
Chapter 6. APPLICATIONS OF BLUETOOTH
1. Before using Bluetooth
2. Bluetooth Applications

CONFIDENTIAL Page 8 2004/8/20
Chapter 1. APPEARANCE
Front
Rear
Stylus Pen HDD Cover
Screw Hole
Rubber Foot
Battery
Speaker Hole
Port Cover

CONFIDENTIAL Page 9 2004/8/20
Top USB
Bottom
Right Side
Left Side
USB Stylus Pen
DC In
PS/2
PCMCIA Slot Mini VGA Port
Mic Jack
Speaker Jack Battery

CONFIDENTIAL Page 10 2004/8/20
Chapter 2. KEY FUNCTIONS:
This chapter describes key-button operation.
1 Alt 2 Arrow 3 Ctrl 4 Rotate
5
Battery
LED
6 Power key 7
GPS
(Keyboard
Key) 8 Esc
9 Tab 10 Enter 11 Mic
1. Alt Key.
Works as Alt key of the keyboard in Windows mode.
2. Arrow Keys.
Work as Arrow Keys of the keyboard in Windows mode.
3. Ctrl Key.
Works as Ctrl Keys of in the keyboard in Windows mode.
4. Rotate Key.

CONFIDENTIAL Page 11 2004/8/20
Rotates the whole screen 90 degrees.
5. Battery LED.
In charging(Power On) : Red light - On
In charging(Power Off) : Red light – Blinking
Request to charge(Power On) : Red light
Fully Charged (Power On): Green light – On
Fully Charged (Power Off): Light off
6. Power Key.
Powers SmartTablet on and off. Hibernate mode function can be added by changing the
Windows’ setting. However, with standby mode activated and when the power is on,
SmartTablet can be forced to power off by pressing and holding this key down or it will go
into Hibernate by pressing this key once. By pressing this key once again, SmartTablet
will be out of Hibernate mode.
7. GPS (Keyboard Key)
Toggles to hide or show the Soft Keyboard window once the software is running.
8. Esc Key.
Works as Esc Key of the keyboard in Windows mode.
9. Tab Key.
Works as Tab Key of the keyboard in Windows mode.
10 . Enter Key.
Works as Enter Key of the keyboard in Windows mode.
11. Mic.
Microphone
*** Combination Keys. ***
-
- Functions when ALT key and another key (other than ALT key) are pressed together in
Windows Mode.
 ALT + RIGHT ARROW => SPEAKER VOLUME UP
 ALT + LEFT ARROW => SPEAKER VOLUME DOWN
 ALT + UP ARROW => BRIGHT UP LCD PANEL

CONFIDENTIAL Page 12 2004/8/20
 ALT + DOWN ARROW => BRIGHT DOWN LCD PANEL
 ALT + Ctrl + KBD => SYSTEM RESET
 ALT + ROTATE => NUMBER KEY(TOGGLE)
 ALT + KBD => INPUT ID(In the Future)
 ALT + ESC => ACTIVATED WINDOW CLOSE OR SYSTEM RESET
 ALT + TAB => ACTIVATED WINDOW CONVERSION
 ALT + ENTER => WHOLE SCREEN DISPLAY AT WINDOWS MEDIA PLAYER
 Ctrl + TAB => ACTIVATED CALIBRATION MODE TO CALIBRATE TOUCH PANEL

CONFIDENTIAL Page 13 2004/8/20
Chapter 3. SETTING UP SmartTablet HARDWARES:
1. Installing the battery pack to SmartTablet.
The rechargeable battery is packed separately from SmartTablet and should be slide in
very carefully to the bottom of SmartTablet. The battery should be fully charged before
using it for the first time.
2. Connecting to the power.
- Connect AC/DC adapter/battery charger to the power port located on the right side of
SmartTablet.
- Connect AC/DC adapter/battery charger to the power receptacle.
- Green LED light will be shown on the AC/DC adapter indicating the battery is being fully
charged.
3. Charging Time.
It will take about 3 hours for the battery to be fully charged.
4.Handle The Battery Pack With Cautions.
- Only use the AC adapter that comes with SmartTablet.
- If the battery is not used for long period of time, totally drain the battery out.
- If the temperature of the battery pack goes higher than 60°C, remove the pack and let it
cool down in room temperature before using it again.
- Do not leave the battery pack exposed direct sunlight or heated up.
- Do not disassemble the battery pack.
- Do not drop the battery pack or give physical shock.
- Do not let children play with the battery.

CONFIDENTIAL Page 14 2004/8/20
Chapter 4. USING AND SETTING SmartTablet.
1. Power on.
After battery pack is fully charged, press the Power Key. The green Power LED light will
be on indicating the power is on.
2. Power off.
There are two ways of powering SmartTablet off.
1. Shut down the system from Windows.
- Select Start from Taskbar -> Select Shut Down from Start menu.
- Check Shut Down from Shut Down Windows menu -> Select OK.
2. Changing the function of Power Key.
- Select Start from Taskbar-> Select Settings -> Select Control Panel.
- Select Power Management Icon from Control Panel.
- Select Advanced tap -> Reconfigure Power Buttons setting -> Select Apply.
3. Rotate Button Setting
1) Select “Settings” in “Start
Menu” and click “Control
Panel”
2) Click “Display” icon.

CONFIDENTIAL Page 15 2004/8/20
3) Select “Lynx3DM+”, and Press
“Hot Key Settings” button.
4) Setting “90 degree” to “Ctrl + Shift +
F11” and “Turn off special mode” to
“Ctrl + Shift + F12”, and then click
“OK” button.

CONFIDENTIAL Page 16 2004/8/20
4. Media Player 6.4 Setting.
To see high quality movie, Windows Media Player 6.4 is better than Windows Media Player 7.0
1) Execute “C:₩Program
files₩Windows Media
Player₩Mplayer2”
2) Select “View” in the
menu bar and Click
“Option”.

CONFIDENTIAL Page 17 2004/8/20
3) Select “Formats”.
4) Click “Select All” Button
5) Click “OK” Button

CONFIDENTIAL Page 18 2004/8/20
5. Display setting
6. Touch Screen.
Touch the screen to select the icons in Windows environment in order the run the
1) [Start] -> [Setting] -> [Control
Panel] -> [Display Properties]
2) Select “High Color(16 bit)”
3) Manupulate 800 by 600 pixels
4) Select “Apply the new color settings
without restarting?”, and then click
“OK” button.

CONFIDENTIAL Page 19 2004/8/20
applications/programs or to draw in the Paint application.
Touch Configuration Icon
1) Click Touch
Configuration Icon
2) Check that Connect is “OK” sign in
“Controller Information” Frame.
If not, Click “Auto” Button and then
“OK” sign could appear.
3) Choose “TIME” mode in Right Button,
and adjust Cursor Offset Arrow if you
would set the curser more correctly.

CONFIDENTIAL Page 20 2004/8/20
4) If you calibrate the touch panel in
SMARTTABLET, click “Calibration”
button.
5) First point should be touched in 1~
2 second and then “Calibration first
point success”Box would come
out, if you do calibrate correctly.
Second point should be done in
same way.
Note : Push “Ctrl + Tab” Key in
SMARTTABLET, if the touch
panel doen’t work correctly.
6) If you’d like to test touch position or
status, Click “Draw” button and then
check them.
Second point
First point