Samsung C100R-5 User manual

MICROWAVE OVEN CONTENTS
MICROWAVE OVEN
1. Precaution
2. Specifications
3. Operating Instructions
4. Disassembly and Reassembly
5. Alignment and Adjustments
6. Troubleshooting
7. Exploded Views and Parts List
8. PCB Diagrams
9. Schematic Diagrams
Manual
C100R-5
C100R-5(SILVER)
SER

ELECTRONICS
©Samsung Electronics Co., Ltd. November 2003
PrintedinKorea
Code No. : DE68-03334A
This Service Manual is a property of Samsung Electronics Co.,Ltd.
Any unauthorized use of Manual can be punished under applicable
International and/or domestic law.

PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
(a) Do not operate or allow the oven to be
operated with the door open.
(b) Make the following safety checks on
all ovens to be serviced before activating
the magnetron or other microwave
source, and make repairs as necessary:
(1) Interlock operation,
(2) proper door closing,
(3) seal and sealing surfaces (arcing,
wear, and other damage),
(4) damage to or loosening of hinges
and latches,
(5) evidence of dropping or abuse.
(c) Before turning on microwave power
for any service test or inspection within
the microwave generating
compartments, check the magnetron,
wave guide or transmission line, and
cavity for proper alignment, integrity,
and connections.
(d) Any defective or misadjusted
components in the interlock, monitor,
door seal, and microwave generation
and transmission systems shall be
repaired, replaced, or adjusted by
procedures described in this manual
before the oven is released to the
owner.
(e) A Microwave leakage check to verify
compliance with the Federal
performance standard should be
performedoneachovenpriorto
release to the owner.

ڈٻڌٻڈ
1. Precaution
Follow these special safety precautions. Although the microwave oven is completely safe during ordinary use,
repair work can be extremely hazardous due to possible exposure to microwave radiation, as well as potentially
lethal high voltages and currents.
1-1 Safety precautions ( )
1. All repairs should be done in accordance
with the procedures described in this
manual. This product complies with
Federal Performance Standard 21 CFR
Subchapter J(DHHS).
2. Microwave emission check should be
performed to prior to servicing if the oven is
operative.
3. If the oven operates with the door open :
Instruct the user not to operate the oven and
contact the manufacturer and the center for
devices and radiological health immediately.
4. Notify the Central Service Center if the
microwave leakage exceeds 5 mW/cm2.
5. Check all grounds.
6. Do not power the MWO from a "2-prong"
AC cord. Be sure that all of the built-in
protective devices are replaced. Restore any
missing protective shields.
7. When reinstalling the chassis and its
assemblies, be sure to restore all protective
devices, including: nonmetallic control
knobs and compartment covers.
8. Make sure that there are no cabinet openings
through which people --particularly
children --might insert objects and contact
dangerous voltages. Examples: Lamp hole,
ventilation slots.
9. Inform the manufacturer of any oven found
to have emission in excess of 5 mW/cm2,
Make repairs to bring the unit into
compliance at no cost to owner and try to
determine cause.
Instruct owner not to use oven until it has
been brought into compliance.
CENTRAL SERVICE CENTER
10. Service technicians should remove their
watches while repairing an MWO.
11. To avoid any possible radiation hazard,
replace parts in accordance with the wiring
diagram. Also, use only the exact
replacements for the following parts:
Primary and secondary interlock switches,
interlock monitor switch.
12. If the fuse is blown by the Interlock Monitor
Switch: Replace all of the following at the
same time: Primary, door sensing switch
and power relay, as well as the Interlock
Monitor Switch. The correct adjustment of
these switches is described elsewhere in
this manual. Make sure that the fuse has the
correct rating for the particular model being
repaired.
13. Design Alteration Warning:
Use exact replacement parts only, i.e.,
only those that are specified in the
drawings and parts lists of this manual.
This is especially important for the
Interlock switches, described above.
Never alter or add to the mechanical or
electrical design of the MWO. Any design
changes or additions will void the
manufacturer's warranty. Always unplug
the unit's AC power cord from the AC
power source before attempting to
remove or reinstall any component or
assembly.
14. Never defeat any of the B+ voltage
interlocks. Do not apply AC power to the
unit (or any of its assemblies) unless all
solid-state heat sinks are correctly installed.
15. Some semiconductor ("solid state") devices
are easily damaged by static electricity.
Such components are called
Electrostatically Sensitive Devices (ESDs).
Examples include integrated circuits and
field-effect transistors.
Immediately before handling any
semiconductor components or assemblies,
drain the electrostatic charge from your
body by touching a known earth ground.
16. Always connect a test instrument's ground
lead to the instrument chassis ground before
connecting the positive lead; always remove
the instrument's ground lead last.

ڈٻڍٻڈ
1-2 Special Servicing Precautions (Continued)
17. When checking the continuity of the witches
or transformer, always make sure that the
power is OFF, and one of the lead wires is
disconnected.
18. Components that are critical for safety are
indicated in the circuit diagram by
shading, or .
19. Use replacement components that have the
same ratings, especially for flame resistance
and dielectric strength specifications. A
replacement part that does not have the
same safety characteristics as the original
might create shock, fire or other hazards.
1-3 Special High Voltage Precautions
1. High Voltage Warning
Do not attempt to measure any of the high
voltages --this includes the filament voltage
of the magnetron. High voltage is present
during any cook cycle.
Before touching any components or wiring,
always unplug the oven and discharge the
high voltage capacitor (See Figure 1-1)
2. The high-voltage capacitor remains charged
about 30 seconds after disconnection. Short
the negative terminal of the high-voltage
capacitor to to the oven chassis. (Use a
screwdriver.)
3. High voltage is maintained within specified
limits by close-tolerance, safety-related
components and adjustments. If the high
voltage exceeds the specified limits, check
each of the special components.
PRECAUTION
There exists HIGH VOLTAGE ELECTRICITY
with high current capabilities in the circuits of the
HIGH VOLTAGE TRANSFORMER secondary
and filament terminals. It is extremely dangerous
to work on or near these circuits with the oven
energized.
DO NOT measure the voltage in the high voltage
circuit including filament voltage of magnetron.
PRECAUTION
Never touch any circuit wiring with your hand
nor with uninsulated tool during operation.
PRECAUTION
Servicemen should remove their watches
whenever working close to or replacing the
magnetron.
Fig. 1-1. Discharging the High Voltage Capacitor
H. V. Diode
Short
H. V. Capacitor
Touch chassis ground first then short to the high
volta
g
e capacitor terminal b
y
usin
g
screwdriver o
r
jumper wire.

ڈٻڎٻڈ
2. Specifications
2-1 Table of Specifications
TIMER
POWER SOURCE
POWER CONSUMPTION
OUTPUT POWER
OPERATING FREQUENCY
MAGNETRON
COOLING METHOD
OUTSIDE DIMENSIONS
NET WEIGHT
GROSS WEIGHT
99 MINUTES
230V 50Hz, AC
MICROWAVE : 1,400W
GRILL : 1,300W
CONVECTION : 1,700W
FROM 100 TO 900W(6 LEVEL POWER)
(IEC-705 TEST PROCEDURE)
2,450MHz
OM75P(31)ERHN
COOLING FAN MOTOR
517(W) x 310(H) x 511(D)mm
19.0 kg
22.5 kg


517mm
369mm
310mm
216mm
511mm
3. Operating Instructions
3-1 Control Panel
3-2 Features & External Views
Door
Ventilation Holes Light Safety Interlock Holes
Control Panel
Guide Roller
Coupler
Grill Rack
Glass Plate
Door Latches

ڈٻڐٻڈ
4. Disassembly and Reassembly
4-1 Replacement of Magnetron, Motor Assembly and Lamp
Remove the magnetron including the shield case,
permanent magnet, choke coils and capacitors (all
of which are contained in one assembly).
1. Disconnect all lead wires from the magnetron
and lamp.
2. Remove the bracket mounting.
3. Remove the magnetron supporter.
4. Remove the air cover.
5. Remove screws securing the magnetron to the
wave guide.
6. Take out the magnetron very carefully.
7. Remove screws from the back panel.
8. Take out the fan motor.
9. Remove the oven lamp by rotating to pull out from
hole of air cover.
NOTE1: When removing the magnetron, make sure that its antenna does not hit any adjacent parts, or it
may be damaged.
NOTE2: When replacing the magnetron, be sure to remount the magnetron gasket inthe correct position and
make sure the gasket is in good condition.
4-2 Replacement of High Voltage Transformer
1. Discharge the high voltage capacitor.
2. Disconnect all the leads.
3. Remove the mounting bolts.
4. Reconnect the leads correctly and firmly.
PRECAUTION
Servicemen should remove their watches
whenever
working close to or replacing the magnetron.
PRECAUTION
There exists HIGH VOLTAGE ELECTRICITY with
high current capabilities in the circuits of the
HIGH VOLTAGE TRANSFORMER secondary
and filament terminals. It is extremely dangerous
to work on or near these circuits with the oven
energized.
DO NOT measure the voltage in the high voltage
circuit including filament voltage of magnetron.

ڈٻڑٻڈ
4-3 Replacement of Door Assembly
4-3-1 Removal of Door Assembly
securing the upper hinge and lower hinge.
The remove door assembly.
4-3-2 Removal of Door "C"
Insert flat screwdriver into the gap between Door
"A" and Door "C" to remove Door "C". Be careful
when handling Door "C" because it is fragile.
4-3-3 Removal of Door "E"
Following the procedure as shown in the figure,
insert and bend a thin metal plate between Door
"E" and Door "A" until you hear the 'tick' sound.
1. Insertion depth of the thin metal plate should be
0.5mm or less.
4-3-4 Removal of Key Door &Spring
Remove pin hinge from Door "E"
Datach spring from Door "E" and key door.
4-3-5RemovalofScreen-Door&Deco-Door
1. Remove Door "E" from Door "A"
2. Remove Door-Screen"B" and Deco Door.
Door "E"
Deco-Door

ڈٻڒٻڈ
4-3-6 Reassembly Test
1. When mounting the door to the oven, be sure to adjust the door parallel to the bottom line of the
oven face plate by moving the upper hinge and lower hinge in the direction necessary for proper
alignment.
2. Adjust so that the door has no play between the inner door surface and oven front surface. If the door
assembly is not mounted properly, microwave energy may leak from the space between the door and oven.
3. Do microwave leakage test.
4-4 Replacement of Fuse
1. Disconnect the oven from the power source.
2. When 15A fuse blows out by the operation of interlock monitor switch failure, replace the primary interlock
switch, door sensing switch, monitor switch and power relay.
3. When the above three switches operate properly, check if any other part such as the control circuit board,
blower motor or high voltage transformer is defective.
4-5 Replacement of Drive Motor
1. Take out the glass tray, guide roller from oven cavity, disconnect power.
2. Remove turn table motor cover from case bottom.
CAUTION : Remove sharp edge after cover removal.
3. Disconnect leads from motor.
4. Remove the screws securing motor to bottom of over
cavity and left out the motor.
5. When replacing the motor, be sure to remount it in the
correct position.
NOTE : The shaft of motor should fit tip coupler.
6. Screw the motor to bottom of oven cavity.
7. Connect leads to the drive motor.
8. Screw the drive motor cover to the base plate
with a screw driver.
NOTE : Bring the spare screw from service center.
COVER FIXING SCREW:
MATCHINE SCREW (TAP TITED SCREW)
After replacement of defective component parts of the door, reassemble it and follow the instructions
below for proper installation and adjustment so as to prevent an excessive microwave leakage.

ڈٻړٻڈ
4-6 Replacement of Control Circuit Board
1. Be sure to disclyarge any static electricity from
your body, and avoid touching the "touch
control" circuitry.
2. Disconnect the connectors from the control
circuit board.
3. Remove screws securing the control box
assembly.
4. Lift up the control circuit board from right side
and remove the hooks holding the control
circuit board to the box assembly.
SCREWS

ڈٻڔٻڈ
5. Alignment and Adjustments
5-1 High Voltage Transformer
1. Remove connectors from the transformer terminals
and check continuity.
2. Normal resistance readings are as follows:
(Room temperature = 20°C)
5-2 Low Voltage Transformer
1. The low voltage transformer is located on the
Assy base plate.
2. Remove the low voltage transformer from the
Assy base plate and check continuity.
3. Normal resistor reading is shown in the table.
5-3 Magnetron
1. Continuity checks can indicate only an open
filament or a shorted magnetron. To diagnose an
open filament or shorted magnetron :
2. Isolate the magnetron from the circuit by
disconnecting its leads.
3. A continuity check across the magnetron filament
terminals should indicate one ohm or less.
4. A continuity check between each filament terminal
and magnetron case should read open.
PRECAUTION
1. High voltage is present at the high voltage terminals during any cook cycle.
2. It is neither necessary nor advisable to attempt measurement of the high voltage.
3. Before touching any oven components or wiring, always unplug the oven from its power source and
discharge the high voltage capacitor.
Terminals Resistance
1~2(Input)
3~4(Output)
5~6(Output)
290Ω.
4.0Ω..
1.0Ω.
Secondary
Filament
Primary
Approx. 100˟
Approx. 0˟
Approx. 1.450˟
Cooling Fins
Magnetron Antenna
Gasket Plate
Filament Terminals
Primary
Terminals
Secondary
Terminal

ڈٻڌڋٻڈ
5-4 High Voltage Capacitor
1. Check continuity of the capacitor with the meter set at the highest resistance scale.
2. Once the capacitor is charged, a normal capacitor shows continuity for a short time, and then indicates 9Mഐ.
3. A shorted capacitor will show continuous continuity.
4. An open capacitor will show constant 9Mഐ.
5. Resistance between each terminal and chassis should read infinite.
5-5 High Voltage Diode
1. Isolate the diode from the circuit by disconnecting its leads.
2. With the ohm-meter set at the highest resistance scale, measure across the diode terminals. Reverse the
meter leads and read the resistance. A meter with 6V, 9V or higher voltage batteries should be used to
check the front-to back resistance of the diode (otherwise an infinite resistance may be read in both
directions). The resistance of a normal diode will be infinite in one direction and several hundred Kഐin the
other direction.
5-6 Main Relay and Power Control Relay
1. The relays are located on the PCB Ass'y. Isolate them from the main circuit by disconnecting the leads.
2. Operate the microwave oven with a water load in the oven. Set the power level set to high.
3. Check continuity between terminals of the relays after the start pad is pressed.
5-7 Adjustment of Primary Switch, Door Sensing Switch and Monitor Switch
1. When mounting Primary switch and Interlock
Monitor switch to Latch Body, consult the figure.
2. No specific adjustment during installation of
Primary switch and Monitor switch to the latch
body is necessary.
3. When mounting the Latch Body to the oven
assembly, adjust the Latch Body by moving it so
that the oven door will not have any play in it.
Check for play in the door by pulling the door
assembly. Make sure that the latch keys move
smoothly after adjustment is completed.
Completely tighten the screws holding the Latch
Body to the oven assembly.
4. Reconnect to Monitor switch and check the
continuity of the monitor circuit and all latch
switches again by following the components test
procedures.
5. Confirm that the gap between the switch
housing and the switch actuator is no more than
0.5mm when door is closed.
6. Interlock Switch Replacement - When
replacing faulty switches, be sure switch mounting
tabs are not bent, broken or otherwise deficient in
their ability to secure the switches in place.
Precaution
For continued protection against radiation hazard, replace parts in accordance with the wiring diagram and be sure to
use the correct part number for the following switches: Primary and secondary interlock switches, and the interlock
monitor switch (replace all together). Then follow the adjustment procedures below. After repair and adjustment, be
sure to check the continuity of all interlock switches and the interlock monitor switch.
Primary Interlock Switch
Door Open Door Closed
Primary switch
Monitor switch(COM-NC)
Door Sensing S/W
∞
0
∞
0
∞
0
Body Latch
Interlock Monitor
Switch
Door Sensing
Switch
Lever Door(B)

ڈٻڌڌٻڈ
5-8 Output Power of Magnetron
The output power of the magnetron can be measured by performing a water temperature rise test.
Equipment needed :
* Two 1-liter cylindrical borosilicate glass vessel (Outside diameter 190 mm)
* One glass thermometer with mercury column
NOTE: Check line voltage under load. Low voltage will lower the magnetron output. Make all temperature
and time tests with accurate equipment.
1. Fill the one liter glass vessel with water.
2. Stir water in glass vessel with thermometer, and record glass vessel's temperature ("T1", 10±1°C).
3. After moving the water into another glass vessel, place it in the center of the cooking tray. Set the oven to
high power and operate for 49 seconds exactly. (3 seconds included as a holding time of magnetron
oscillation:)
4. When heating is finished, stir the water again with the thermometer and measure the temperature ("T2").
5. Subtract T1 from T2. This will give you the water temperature rise. (ଠT)
6. The output power is obtained by the following formula;
Output Power = 4.187 x 1000 x ଠT + 0.88 x Mc x(T2-T0) 49:HeatingTime(sec)
46 4.187 : Coefficient for Water
1000 : Water (cc)
ଠT : Temperature Rise (T1-T2)
Mc : Cylindrical borosilicate glass weight
To : Room Temperature
7. Normal temperature rise for this model is 9°C to 11°C at 'HIGH'.
NOTE 1: Variations or errors in the test procedure will cause a variance in the temperature rise.
Additional power test should be made if temperature rise is marginal.
NOTE 2: Output power in watts is computed by multiplying the temperature rise (step E) by a factor of 91
times the of centigrade temperature.
CAUTION
MICROWAVE RADIATION
PERSONNEL SHOULD NOT ALLOW EXPOSURE TO MICROWAVE RADIATION FROM MICROWAVE
GENERATOR OR OTHER PARTS CONDUCTING MICROWAVE ENERGY.

ڈٻڌڍٻڈ
5-9 Procedure for Measurement of Microwave Energy Leakage
1) Pour 275±15cc of 20±5°C(68±9°F) water in a beaker
which is graduated to 600cc, and place the beaker in
the center of the oven.
2) Start to operate the oven and measure the leakage by
using a microwave energy survey meter.
3) Set survey meter with dual ranges to 2,450MHz.
4) When measuring the leakage, always use the 2 inch
spacer cone with the probe. Hold the probe
perpendicular to the cabinet door. Place the spacer
cone of the probe on the door and/or cabinet door
seam and move along the seam, the door viewing
window and the exhaust openings moving the
probe in a clockwise direction at a rate of 1 inch/sec. If the leakage testing of the cabinet door seam is
taken near a corner of the door, keep the probe perpendicular to the areas making sure that the probe end
at the base of the cone does not get closer than 5cm to any metal. If it gets closer than 5cm, erroneous
readings may result.
5) Measured leakage must be less than 4mW/cm2,after repair or adjustment.
5-10 Check for Microwave Leakage
1. Remove the outer panel.
2. Pour 275±15cc of 20±5°C(68±9°F) water in a beaker
which is graduated to 600cc, and place the beaker in
the center of the oven.
3. Start the oven at the highest power level.
4. Set survey meter dual ranges to 2,450MHz.
5. Using the survey meter and spacer cone as described
above, measure near the opening of magnetron, the
surface of the air guide and the surface of the wave
guide as shown in the following photo.( but avoid the
high voltage components.) The reading should be
less than 4mW/cm2.
5-11 Note on Measurement
1) Do not exceed the limited scale.
2) The test probe must be held on the grip of the handle, otherwise a false reading may result when the
operator's hand is between the handle and the probe.
3) When high leakage is suspected, do not move the probe horizontally along the oven surface; this may
cause damage to the probe.
4) Follow the recommendation of the manufacturer of the microwave energy survey meter.
5-12 Leakage Measuring Procedure
5-12-1 Record keeping and notification after measurement
1) After adjustment and repair of a radiation preventing device, make a repair record for the measured
values, and keep the data.
2) If the radiation leakage is more than 4 mW/cm2after determining that all parts are in good condition,
functioning properly and the identical parts are replaced as listed in this manual notify that fact to ;
CENTRAL SERVICE CENTER
5-12-2 At least once a year have the microwave energy survey meter checked for accuracy by its manufacturer.
Maximum allowable leakage is 5mW/cm2.
4mW/cm2is used to allow for measurement and meter accuracy
WARNING
AVOID THE HIGH VOLTAGE COMPONENTS

ڈٻڌڎٻڈ
6. Troubleshooting
6-1 Electrical Malfunction
PRECAUTION
1. CHECK GROUNDING BEFORE CHECKING FOR TROUBLE.
2. BE CAREFUL OF THE HIGH VOLTAGE CIRCUIT.
3. DISCHARGE THE HIGH VOLTAGE CAPACITOR.
4. WHEN CHECKING THE CONTINUITY OF THE SWITCHES OR TRANSFORMER, DISCONNECT
ONE LEAD WIRE FROM THESE PARTS AND THEN CHECK CONTINUITY WITHOUT THE
POWER SOURCE ON. TO DO OTHERWISE MAY RESULT IN A FALSE READING OR DAMAGE
TO YOUR METER.
5. DO NOT TOUCH ANY PART OF THE CIRCUIT OR THE CONTROL CIRCUIT BOARD, SINCE
STATIC DISCHARGE MAY DAMAGE IT.
ALWAYS TOUCH GROUND WHILE WORKING ON IT TO DISCHARGE ANY STATIC CHARGE
BUILT UP.
SYMPTOM CAUSE CORRECTIONS
Oven is dead.
Fuse is OK.
No display and no operation at all.
1. Open or loose lead wire harness
2. Open thermal cutout (Magnetron)
3. Open low voltage transformer
4. Defective Ass'y PCB
Check fan motor when thermal
cutout is defective.
Check Ass'y PCB when L.V.T
is defective.
No display and no operation at all.
Fuse is blown. 1. Shorted lead wire harness
2.Defectiveprimarylatchswitch
(NOTE 1)
3. Defective monitor switch (NOTE1)
4. Shorted H.V.Capacitor
5. Shorted H.V.Transformer (NOTE2)
Check adjustment of primary,
interlock monitor,
power relay, door sensing
switch.
NOTE 1: All of these switches must be replaced at the same time.
(refer to adjustment instructions)
Check continuity of power relay contacts and if it has
continuity, replace power relay also.
NOTE 2: When H.V.Transformer is replaced, check diode and
magnetron also.
Oven does not accept
key input (Program) 1. Key input is not in-Sequence 2. Open or loose connection of
membrane key pad to Ass'y PCB
3. Shorted or open membrane panel
4. Defective Ass'y PCB
Refer to operation procedure.
Replace PCB main.
Timer starts countdown but no
microwave oscillation.
(No heat while oven lamp and fan
motor turn on.)
1. Off-alignment of latch switches
2. Open or loose connection of high
voltage circuit especially
magnetron filament circuit
NOTE: Large contact resistance will
bring lower magnetron
filament voltage and cause
magnetron to lower output
and/or intermittent oscillation.
3. Defective high voltage
components H.V.Transformer
H.V. Capacitor
H.V.Diode, H.V.Fuse
Magnetron
4. Open or loose wiring of power relay
5.Defectiveprimarylatchswitch
6. Defective power relay or Ass'y PCB
Adjust door and latch switches.
Check high voltage component
according to
component test procedure and
replace if it is
defective.
Replace PCB main.

ڈٻڌڏٻڈ
6-1 Electrical Maltunction(continved)
SYMPTOM CAUSE CORRECTIONS
Oven lamp and fan motor turn on 1. Misadjustment or loose wiring
of primary latch switch
2.Defectiveprimarylatchswitch
Adjust door and latch switches.
Oven can program but timer
does not start. 1. Open or loose wiring of secondary interlock switch
2. Off-alignment of primary
interlock
3.
Defective secondary interlock S/W
Adjust door and interlock switches.
Microwave output is low;.
Oven takes longer time to
cook food.
1. Decrease in power source
voltage.
2. Open or loose wiring of
magnetron filament circuit.
(Intermittent oscillation))
3. Aging of magnetron
Consult electrician.
Fan motor turns on when plugged in Loose wiring of door sensing switch Check wire of door sensing switch.
Oven does not operate and return to
the plugged in mode. Defective Ass'y PCB Replace PCB main.
Loud buzzing noise can be heard. 1. Loose fan and fan motor
2. Loose screws on
H.V.Transformer
3. Shorted H.V.Diode
Tighten screws of fan motor.
Tighten screws of H.V.Transformer.
Replace H.V.Diode.
Turntable motor does not rotate. 1. Open or loose wiring of
turntable motor.
2. Defective turntable motor.
Replace turntable motor.
Oven stops operation during
cooking 1. Open or loose wiring of primary interlock switch
2. Operation of thermal
cutout(Magnetron)
Adjust door and latch switches.
Sparks 1. Metallic ware or cooking dishes
touching on the oven wall.
2. Ceramic ware trimmed with
gold or silver powder also
causes sparks.
Inform the customer.
Do not use any type of cookware
with
metallic trimming.
Uneven cooking Uneven intensity of microwave due
to its characteristics. Wrap thinner parts of the food with
aluminum foil.
Use plastic wrap or cover with a lid.
Stir once or twice while cooking
foods such as soup, cocoa, or milk.
Noise from the turntable motor
when it starts to operate. Noise may result from the motor. Replace turntable motor.

ڈٻڌڐٻڈ
7. Exploded Views and Parts List
7-1 Exploded Views
M001
W006
W003
M035
M037
M005
M041
M043
MM105
MM103
MM104
M046
M047
M040
M039
M038
M049
T001
T017
M034
T010
T009
M051
M054
M053 M057
M048
M031
M113 M095
M009
M008M010
M011
M013
H016
M015
W002
M017
M019
M023
M036
M004
M029
M016
M012
B018
B006 B001
B002
B009

ڈٻڌڑٻڈ
7-2 Main Parts List
No. Code No. Description Specification Q'ty Remark
B001 3405-001034 SWITCH-MICRO 125/250VAC,16A,200GF,SPST-N 2
B002 3405-001032 SWITCH-MICRO 125/250VAC,16A,200GF,SPDT 1
B006 DE66-40021B LATCH-BODY -,-,-,M959/XSA,-,-,- 1
B009 DE66-90054B LEVER-SWITCH NYLON#66(2021SW),40G,M959/X 1SENSOR
B018 DE93-20020D ASSY BODY LATCH M959/XSA,-,-,-,- 1HEATER
M001 DE64-01161A PANEL-OUTER 5th. 1.0 Convection,SECC,T0. 1WHITE
M001 DE64-01161B PANEL-OUTER 5th. 1.0 Convection,SECC,T0.6,W360,L1128,-,silver,- 1SILVER
M004 DE61-50490A BRACKET-TCO -,SECC1,T0.6,34,58,-,- 1
M005 DE61-70060A SPRING-PLATE -,SK-5,T0.5,-,-,-,-,-,-,-,- 1
M008 DE63-20017A GASKET-HEATER -,BRASS,T1.5,OD30.5,ID22.5 1
M009 DE60-40009B WASHER-TEFLON SLOT,ID22.2,OD28,T1.2,TEFL 1
M010 DE61-50021A BRACKET-FLANGE -,SECC1,T0.8,32,32,-,- 1
M011 DE61-50347A BRACKET-EARTH -,BSS2-A,T1.0,W35,L43,MBGF 1
M012 DE61-50027B BRACKET-HEATER -,SECC,T1.0,W51,L55,CE945 1
M013 DE61-50570C BRACKET-AIR GUIDE CK95,SECC,T0.8,-,-,-,D 1
M015 DE39-00022B ASSY POWER CORD 4819D,CK135,230V50Hz,-,- 1
M016 DE63-00240A COVER-BACK EU-1.0 CONV,SECC/PHOSPHATE,T0 1
M017 DE96-00011A ASSY NOISE FILTER SN-3WUA,250V15A,3W 15A 1
M019 3601-001197 FUSE-CARTRIDGE 250V,15A,SLOW-BLOW,CERAMI 1
M023 DE31-00001D MOTOR FAN -,SMF-2D3EA,230V50Hz,-,M1D33CE 1
M029 DE47-20009A THERMOSTAT PW2N-520PB,160/60,250V/7.5A,H 1MGT
M031 DE47-20009A THERMOSTAT PW2N-520PB,160/60,250V/7.5A,H 1
M034 DE67-00182A COUPLER 5TH-1.0,PPS,-,-,-,- 1
M035 OM75P(31)ERHN ASSY-MAGNETRON OM75P(31)ERHN 1
M037 DE63-00248A COVER-AIR 5th. 1.0 Convection,Nylon #66( 1
M038 DE26-00096A TRANS H.V SHV-EURO2-1,230V,50Hz,2350V,3. 1
M039 2501-001015 C-OIL 1.0uF,2100V,BK,35X54X80,20mm 1
M040 DE61-50106A BRACKET-HVC -,SECC,T0.8,W31,L125.8,-,- 1
M041 DE91-70065A ASSY-HVD BMP28,SEMA,12KV,SUMI,- 1
M043 DE91-70061A ASSY-H.V.FUSE THV060T-0800-H,5KV/0.80A,W 1
M046 DE60-60025A PIN-FOOT PP-JI350,BLK,-,-,-,-,-,- 4
M047 DE61-40065A FOOT -,PP,T2x22x17mm,BLK,-,-,- 4
M048 DE61-00557F BASE-PLATE 5th. 1.0 Convection,SGCC,T0.6 1
M049 DE31-10170A MOTOR SYNCHRONOUS M2LJ24Z702,ST-16F,220/ 1
M051 DE63-00237A COVER-CEILING CE297DN-5,MICA-SHEET,T0.3, 1
M053 DE61-00623A GUIDE-AIR -,SECC(PHOSPHATE),T0.5,-,-,-,E 1
M054 DE32-10013A SENSOR THERMISTOR PT-312-K2,-,-,-,-,-,- 1
M095 DE47-00001A HEATER SHG-2933E,-,-,1300W(1250W),-,230V 1
M113 DE61-30006A SUPPORT-HEATER -,ALUMINA,5G,2ND-W/P,-,-, 1
P109 DE61-10006B COVER-MOTOR M1D33CE/XSA.RAD,PP(FB53),-,- 1
T001 DE74-20015G TRAY-COOKING 3RD-1.0,T6,1115G,HKS,-,-,-, 1
T009 DE97-00136B ASSY-WIRE RACK CK95,LOW-RACK,-,-,-,- 1
T010 DE97-00136E ASSY-WIRE RACK MG104WA,114,FOOT,VE-TYPE 1
T017 DE97-00222A ASSY-GUIDE ROLLER NC-1.2CUFT,SPS(C832) B 1
W002 DE96-00359A ASSY-WIRE HARNESS A C100-5TH,CONVECTION 1
W003 DE96-00296A ASSY-WIRE HARNESS B CE1100/XEF,CONVECTIO 1
W006 DE39-40409A WIRE HARNESS-E 230V50HZ,M9G45,CTW,-,-,- 1

ڈٻڌڒٻڈ
7-3 Door Parts List
No. Code No. Description Specification Q'ty Remark
D002 DE64-40319A DOOR-A CK95,PC,-,-,-,-,WHT,- 1WHITE
D002 DE64-40319H DOOR-A C100-SL,PC,-,-,-,-,SILVER,- 1SILVER
D006 DE64-40012C DOOR-C CK95,PBT,-,-,-,-,BLK,- 1
D007 DE61-00199A SPRING-KEY M1977,HSWR,D6,-,-,25 1/4,25 1 1
D009 DE61-80002A HINGE-UPPER WHT,SHV-745CC1,SSEC,T2.3,26, 1
D010 DE61-80003A HINGE-LOWER WHT,TN-5630T,SSEC,T2.3,26,77 1
D011 DE64-00547A KEY-DOOR C100,NYLON#66,-,-,-,-,GV10% V0 1
D021 DE64-90160A DECORATION-DOOR -,Y745STC,S7A77,-,-,-,-, 1WHITE
D021 DE64-90160G DECORATION-DOOR C100-SL,PC,-,-,-,-,SILVER,- 1SILVER
D024 DE67-20184K SCREEN-DOOR(B) -,CK920T,TEMP GLASS,T3.2, 1
D043 DE63-00205A CUSHION-SCREEN C115,PC,T2.0,W12,L150,-,- 2
D047 DE94-01031A ASSY DOOR-E(SEALANT) 5th. 1.0 Convection 1
͵ Ͳ΄΄Ί ͵΀΀΃ ʹΈ͹΅ΥΙ  ʹΠΟΧΖΔΥΚΠΟ WHITE (S.N.A)
͵ -ASSY DOOR C100-5SL,SIL,5th. 1.0 Convection SILVER (S.N.A)
S.N.A : SERVICE NOT AVAILABLE
D024
D043
D007
D006
D021
D002
D010
D011
D049
D047 D009