Savannah Heating TASMAN 5000 User manual

Page 1 of 18
TASMAN 5000 & 5000S
Natural Gas & Propane
Outdoor Gas Fireplace
Installation and Operating Instructions
CERT # LC773211
WARNING : If the information in this manual is not followed exactly, a fire or explosion may
result causing property damage, personal injury, or loss of life.
For your safety
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
What to do if you smell gas
Do not try to light any appliance.
Do not touch an y electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbors phone. Follow the gas supplier s
instructions.
If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or the gas
supplier.
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury
or property damage. Read the installation, operating and maintenance instructions thoroughly
before installing or servicing this equipment.
WARNING: For Outdoor Use Only.
Retain this manual for future reference.
Tasman 5000S
Tasman 5000 shown with optional
wind shield

Page 2 of 18
Table of Contents
INTRODUCTION ....................................................................................................................
Specifications ....................................................................................................................... 3
Dimensions ........................................................................................................................... 4
General Safety & Installation Codes ..................................................................................... 5
OPERATION ..........................................................................................................................
Light ing Instructions ............................................................................................................. 6
Flame Adjustment ................................................................................................................ 7
LP Gas Cylinder Safety Information .................................................................................... 8
LP Gas Cylinder Installation ................................................................................................ . 9
NG Safety Information ........................................................................................................ 10
Leak Testing ....................................................................................................................... 10
INSTALLATION ....................................................................................................................
Minimum Clearances ......................................................................................................... 11
Pedestal Door Installation .................................................................................................. 11
Initial Firing & Primary Ai r Adjustment ............................................................................... 12
Altitude Adjustment ............................................................................................................ 13
Field Assembled Parts ........................................................................................................ 13
Lava Rock & Log Installation .............................................................................................. 13
Burner Flame Picture .......................................................................................................... 14
MAINTENANCE ....................................................................................................................
Maintenance Safety ........................................................................................................... 15
Recommended Service ..................................................................................................... 15
Burner Cleaning ................................................................................................................. 15
Trouble Shooting ................................................................................................................ 16
Replacement Parts ............................................................................................................. 16
Warranty ................................................................................................................... 17 & 18
Inca Metal Cutting
100 11091 Bridgeport Road
Richmond, BC V6X 1T3
Canada

Page 3 of 18
1.0 INTRODUCTION
1.1 SPECIFICATIONS
TABLE 1
ITEM NATURAL GAS (NG) PROPANE (LPG)
INPUT: Hi 49,000 Btu/hr (14.36 kW) 49,000 Btu/hr (14. 36 kW)
INPUT: Lo 8,000 Btu/hr (2.34 kW) 17,000 Btu/hr (4.98 kW)
MINIMUM GAS INLET SUPPLY
PRESSURE: Minimum: 7.0 w.c. (1.74 kPa) Minimum: 11 w.c. (2.74 kPa)
MAXIMUM GAS INLET
SUPPLY PRESSURE Maximum: 13.5 w.c. (3.4 kPa) Maximum: 13.5 w.c. (3.4
kPa)
AIR SHUTTER
SETTING
adjustable from fully closed
to fully open
adjustable from fully closed
to fully open
ORIFICE SIZE: @ 0 -2000 # 22 DMS # 45 DMS
The Tasman 5000 is available with a full size pedestal or with a short version (the Tasman 5000S) of
the pedestal for use with a remote cylinder.

Page 4 of 18
APPLIANCE DIMENSIONS
TASMAN 5000
TASMAN 5000S

Page 5 of 18
GENERAL SAFETY
Solid fuels shall not be burned in this fireplace.
Keep the appliance area clear and free from combustible materials, gasoline and other
flammable vapors and liquids.
Inspect the burner prior to each use, if the burner is damaged it must be replaced prior to use.
NOTE: Use only with burner part# OD5007A.
Do not use this appliance if any part has been under water. Immediately call a qualified
service technician to inspect the appliance and to replace any part of the control system and
any gas control which has been under water.
Do not locate the gas supply hose in a pathway where people may trip over it or in areas
where the hose may be subjected to accidental damage.
INSTALLATION CODES
Installation must conform to local codes or in the absence of local codes, installation must conform to
the Nat ional Fuel Gas Code, ANSI Z233.1 , or the current CAN/CGA B149.1 Installation Codes . In the
state of Massachusetts, this product can only be installed by a licensed plumber or a licensed gas
fitter. Failure to comply will void the warranty.
CAUTION
Children and adults should be alerted to the hazards of high surface temperature and
should stay away to avoid burns or clothing ignition.
Young children should be c arefully supervised when they are in the area of the appliance.
Clothing or other flammable material should not be hung from the appliance or placed near
the appliance.
Any guard or other protective device removed for servicing the appliance must be replac ed
prior to operating the appliance.
Installation and repair should be done by a qualified service person. The appliance should
be inspected before use and at least annually by a qualified service person. More frequent
cleaning may be required as necessa ry. It is imperative that control compartments, burners
and circulating air passageways of the appliance be kept clean.

Page 6 of 18
LIGHTING IN STRUCTIONS
FOR YOUR SAFETY, READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
A. BEFORE LIGHTING smell all around the appliance area f or gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electric switch; do not use any phone in your building.
Immediat ely call your gas supplier from a neighbour s phone. Follow the gas suppliers instructions.
If you cannot reach your gas supplier, call the fire department.
B. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob wil l not push in or turn by
hand, don t try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or
explosion.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above on this label.
2. Controls are fo und at the front of the appliance.
3. Push in gas control knob slightly and turn clockwise to OFF .
4. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP!
Follow A in the safety information above on this label. If you don t smell gas, go to the next step.
5. Turn gas supply to unit on.
6. Push in the spark ignition button.
7. Depress and turn control knob counterclockwise to the ON position.
TO TURN GAS OFF TO APPLIANCE
1. Push in gas control knob slightly and turn clockwise to OFF , do not force.
Spark Ignition Knob
Control Knob

Page 7 of 18
FLAME ADJUSTMENT
The valve supplied with the appliance has a HI/LO knob to control the flame height. To adjust the
flame height turn the adjustment knob . Turning the knob in a clockwise direction sets the valve to the
maximum setting, turning the knob in the counterclockwise direction sets the valve to the minimum
setting.
Control Knob

Page 8 of 18
LP GAS CYLINDER SAFETY INFORMATION
T he gas appliance is for use with a gas cylinder that does not exceed 20 lbs. (9 kg) capacity.
The gas cylinder to be used must be constructed and marked in accordance with the
Specifications for LP - Gas Cylinders of the U.S Department of Transportation (D.O .T.) or the
National Standard of Canada CAN/CSA - B339, Cylinders, Spheres and Tubes for Transportation
of Dangerous Goods; and Commission.
This appliance shall be used only outdoors in a well ventilated space and shall not be used in a
building, garage or a ny other enclosed area.
The gas must be turned off at the supply cylinder when the appliance is not in use.
This appliance can be stored indoors only if the cylinder is disconnected and removed from the
appliance.
Cylinders must be stored outdoors in a wel l ventilated area out of the reach of children.
Disconnected cylinders must have threaded plugs tightly installed and must not be stored in a
building, garage or any other enclosed area.
Inspect the hose assembly for damage prior to each use. If the hose is damaged or there are
signs of excessive abrasion or wear replace the hose. See page 9 on how to gain access to hose
assembly.
Use only the pressure regulator and hose assembly supplied with the appliance. Replace the
regulator / hose assembly only wi th part# 150 - 20675, these are available from your local dealer.
The LP cylinder must include a collar to protect the cylinder valve.
The cylinder supply system must be arranged for vapor withdrawal.
This appliance uses a Type 1 cylinder connection devic e see below for proper connection
instructions.
Quick Connect Regulator
Shutoff Valve
Bleeder Screw
Gas Cylinder
Protective Cap
Tighten in This
Direction
Regulator & Hose
WARNING
When disconnecting and removing the gas cylinder, from the appliance, always be sure to
adhere to the following items:
Check that the gas control valve on the appliance as well as on the cylinder are turned
off before disconnecting the gas line from the cylinder.
Never smoke or have an open flame in the vicinity of the gas appliance or gas cylinder.
Upon replacing the gas supply cylinder be sure to tighten all connections and leak test
the connections (with a soapy water solution) prior to placing the tank back in the
enclosure.

Page 9 of 18
L P GAS CYLINDER INSTALLATION
The first step to installing your LP gas cylinder is to remove the pedestal base door, found at the rear
of the appliance. Then you slide the tank into place, there is a round hole which the base of the LP
cylinder will fit into. Then you would attach the regulator hose assembly, leak test (see page 11) and
replace the pedestal door.
Insert bottom of cylinder into hole.
Pedestal Door
For the Tasman 5000S, the cylinder
is to be installed in the tank
stabilizer (part# OD5024).
Tank Stabilizer

Page 10 of 18
NATURAL GAS SAFETY INFORMATION
In addition to LP gas your unit can be operated on natural gas. It is designed to be operated at a
pressure of 7 water column (WC) (1/4 p.s.i. or 1.75 kPa) regulated at the residential meter. Check
with your gas utility for local gas pressure and with your local municipality for building code
requirements. If your residential gas utility line pressure has not been regulated to 7 WC contact
your local gas service provider or local dealer for assistance.
Gas units are preset at the factory to run on ei ther natural gas or LP gas. Do not convert yourself.
Conversion should be done by a qualified technician.
Check with your gas service provider or with local building codes for instructions to install the gas
supply line. This installation must be done by a licensed and qualified installer.
An ON-OFF shutoff valve must be installed between the gas supply source and the fireplace.
Inspect the hose assembly for damage prior to each use. If the hose is damaged or there are signs
of excessive abrasion o r wear replace the hose. See page 9 on how to gain access to hose
assembly.
For outdoor fireplaces that are to be used with natural gas the appliance and its individual shutoff
valve must be disconnected from the gas supply piping system during any press ure testing of the gas
system at test pressures exceeding 1/2 p.s.i. (3.5 kPa).
For outdoor fireplaces that are to be used with natural gas the appliance must be isolated from the
gas supply piping system by closing its individual manual shut off valve du ring any pressure testing of
the gas supply piping system at test pressures equal to or less than 1/2 p.s.i. (3.5 kPa).
GAS SAFETY INFORMATION
How to Leak Test Your Appliance
Mix a solution of liquid soap and water in a small container.
Make sure that the gas supply is turned on. For LP gas appliances make sure that the valve on
the gas cylinder is turned on.
Ensure that the gas control valve on the appliance is in the OFF position.
Use a spray bottle or a small brush and liberally apply the solution to the gas line and to each
connection.
If there are bubbles forming this means that a leak is present.
Tighten any connections that may be loose and leak test again.
If no more leaks are found use the appliance, if leaks persist and cannot be stopped tur n off the
gas supply and contact your distributor or local gas service technician for assistance.
Leak testing with a
small brush.
WARNING : Do not use an open flame to test for gas leaks.