Outdoor GreatRoom Company UPT-1242-BRN User manual

1 | P a g e
Uptown Fire Pit Table
Installation Instructions

2 | P a g e
Contents
Contents……………………………………………………..2
Required Tools…………………………………………..3
Placing and assembling the Table.……4
Gas Connection………………………….…………….5
Igniter Installation…………….………………………...6
Locating Propane tank……………………………8
Finishing Touches……………………………………….9
90223:C 8.2.16

3 | P a g e
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To make gas connections
Leather Gloves
To protect hands from rough edges found
on the coffee table.
One (1) AAA Battery (not included)
Required for piezoelectric igniter
installation.
Do not attempt to perform
installation by yourself. This fire
pit table is constructed of steel
and heavy stone products.
Have at least one other
person help you.

4 | P a g e
Placing and Assembling the Fire Pit table
1. Remove access door from box and set aside.
2. Remove all components from packaging.
3. Move the base sections without door to desired
location and set into place spaced approximately
21” from each other.
4. When locating your coffee table, refer to the
Crystal Fire manual and maintain clearance to
combustibles.
5. Assemble as shown below.
Igniter on side
closest to tank base

5 | P a g e
Read and understand your Crystal Fire owner’s manual
before beginning burner hookups or using the device.
6. Insert supplied sheet metal screws into the locations
shown by arrows below. This secures the granite tile top
to the base.
Align smaller base with concrete top as shown by
dashed line.

6 | P a g e
Gas Connection
1. Lift burner out of top and set aside
2. Connect the incoming gas line and flexible
metal gas line from the valve to the underside
of burner, running flex hose through access
hole as shown before connecting line to
valve. It is not recommended to use Teflon
tape or pipe dope on the connection to the
valve with flare fittings.
LPG installations use the hose and regulator
provided with the burner.
For Natural Gas hookup information and any
other info not listed here consult your Crystal
Fire owner’s manual.
Consult Crystal Fire manual for proper orifice
size for the chosen fuel type before attaching
flex line to burner and tightening securely.

7 | P a g e
Igniter Installation
1. Make sure the valve is in the OFF
position
2. Unscrew sparker cap and hex nut.
Install as shown below.
(If your igniter only has one port on the back, please ignore
instructions for grounding. Your igniter is a self-grounding
model)

8 | P a g e
3. To properly install ignition system, a spark and ground wire
need to be attached to the igniter box.
Start by plugging the spark wire (hanging from the
underside of the sparking tip) on the burner into one
side of the black igniter box on your control panel.
Plug the included grounding wire (which arrives
attached to the underside of your burner pan) into
the back of the sparker box.
Test system by depressing the button on the igniter. A
continuous repeating spark between the igniter
electrode and spark-receiving probe means everything
is connected properly. Consult the troubleshooting
section if spark is weak, intermittent, or not present.
4. Once ignition system is grounded and gas
connections are secured and checked for
leaks, set the burner back into its original
position if you haven’t already done so.

9 | P a g e
Locating your Tank
1. Your tank should be positioned so that
the fuel can be shut off after each use.
2. Slide the tank into the framework past
the line shown below. This is to allow
the door to close completely.
3. Confirm all hoses are clear and not
touching the burner.
Position tank behind this line
Install door by setting the bottom on the catching hooks first and
then closing. Magnets in the table will hold door closed.

10 | P a g e
Finishing touches
Once fire pit is set up and in the desired position,
scatter decorative glass on burner surface forming
an even layer of beads.
DO NOT BURN WITHOUT GLASS OR OTHER
DECORATIVE SUBSTRATE PRESENT
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to hooking up your
linear burner, including safety information, proper tightening of
connections with two wrenches and full burner setup and lighting
instructions.
DO NOT ATTEMPT TO INSTALL CF-1224 BURNER WITHOUT FIRST
CONSULTING THE MANUAL. IF YOU ARE UNSURE OF HOW TO
COMPLETE THE STEPS OUTLINED, CONSULT A QUALIFIED
TECHNICIAN
WARNING
After consulting the manual and following instructions, remember; before operating,
all gas connections must be fully checked for leaks

11 | P a g e
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form
to register your product.

12 | P a g e
© 2011 The Outdoor GreatRoom Company
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]