scoole SC HT CM1 1000 WT User manual

ELECTRIC
CONVECTOR HEATER
ЭЛЕКТРИЧЕСКИЙ
КОНВЕКТОР
EN RUS
SC HT CM1 1000 WT
SC HT CM1 1500 WT
SC HT CM1 2000 WT
Models | Модели
SC HT CL1 1000 WT
SC HT CL1 1500 WT
SC HT CL1 2000 WT
Перед использованием прибора внимательно прочитайте данное руководство
Руководство по эксплуатации
Instruction manual
Please, carefuly read this manual before using the device

2
INSTRUCTION MANUAL
Scoole domestic electric convector is designed to heat and create a comfortable environment
indoors during cold season. The convector can be installed vertically only in a place, where it is
possible to connect to 220 V single-phase power supply wiring. This heating unit is easy-to-use and
easy-to-install, and it is efficient and features operating economy due to minimum electric power
losses, improved heat transfer and maximum comfort heat flow distribution.
1. Important information
Please, read this operation manual carefully prior to use of the convector.
This operation manual contains important information regarding your safety, as well as
recommendations on the proper operation of the unit and its maintenance.
Save this operation manual together with the guarantee card, cash register receipt, if possible,
cardboard box and packing material.
The purchased convector can slightly differ from the one, described in the manual, but that doesn't
affect the methods of its use and operation.
Important precautions and instructions, contained in this manual, do not account for all possible
modes and situations to be encountered. It is vital to understand that common sense, caution and
thoroughness are the factors that are impossible to be built-in in any product.
These factors must be taken into consideration by man who is interested in the proper operation of
the unit. The manufacturer does not bear any responsibility in case when the unit or its parts are
damaged during transportation, as a result of improper installation, voltage fluctuations, as well as if
some part of the unit was altered or modified.
Dear customer!
Thank you for your good choice and purchase of Scoole domestic electric convector.
It will serve you for a long time.

3
ENGLISHElectric convector
2. Precautions
A number of precautions is to be observed upon operation of convector. Improper operation as a
result of ignoring precautions may harm health of the user and other people, as well as damage
their property.
1. Read all instructions prior to operation of the convector.
2. When the convector is operating it heats up to a very high temperature. To prevent burns, do not
touch hot surfaces of the unit by hands or other parts of the body.
3. The unit must be placed away from flammable and easily deformable objects.
4. Make sure that the unit's case and the heating element cooled down prior to the unit is dismantled
and packed for long-term storage.
5. When the unit is not operated for a long time, store it factory-packaged in a dry and cool place.
6. DO NOT COVER THE UNIT when it is operated. Do not dry clothes and any other fabrics and
materials on the unit. It may cause its overheating, failure or inflict significant damage to you and/or
your property.
7. The unit must always be kept watched after, especially with children nearby. Carefully watch
children not to touch the unit by hand.
8. Always disconnect the convector from the mains when it is not used.
9. The unit is equipped with a European-standard plug with a ground pin. The plug must match the
European-standard outlet and enter it without any effort. If the plug doesn't enter the outlet or enters
it too tightly, turn the plug vertically 180° and try again. If you still cannot plug it then you need to call
for an electrician to replace the electric outlet. Never use the unit if the plug is not fully connected to
the outlet.
Уважаемый покупатель!
Благодарим Вас за удачный выбор и приобретение бытового электрического
обогревателя конвекционного типа Scoole. Он прослужит Вам долго.
IMPORTANT!
The manufacturer considers this type of failure a non-guaranteed event.

4
10. Do not connect the unit to the mains if its surface is damp (wet).
11. Never use the unit in a situation when it may contact water.
12. When the unit is switched on and operating, do not touch its surface and the surface of the
control block by wet hands and any parts of the body.
13. Do not switch on the convector if its power cord or plug is damaged. To prevent electric shock,
the damaged power cord must be repaired only in authorized service centers of the manufacturer
and by skilled specialists.
14. Never try to repair it on your own. This may harm your health and affect the unit's guarantee
maintenance.
15. Do not use the convector in open spaces outside.
16. It is forbidden to install and use the unit in bathrooms, shower rooms or swimming pools, in the
very places, where water jets or drops may contact its surface directly when it is switched on.
17. Do not lay the convector's power cord under carpets and do not press it by furniture. Lay the
power cord in such a manner so that it is impossible to trip over it.
18. To switch off the SC HT CM1 series appliance, set the switch on the side of the control panel to
the "OFF" position. To switch off the SC HT CL1 series appliance, press the "POWER" button on the
control panel. Then disconnect the plug of the power cord from the receptacle. Never pull the power
cord or disconnect the plug hardly.
19. Do not thrust fingers and prevent entering of foreign objects into any ventilation, air intakes or air
outlets, since it may cause electric shock or damage of the convector.
20. To prevent a potential fire, do not block air intakes and air outlets. Do not hang and dry things on
the convector! Use the convector only on a dry smooth surface.
21. The convector contains internal hot and sparkling components. Do not use the convector in
places, where petroleum, paint or any other flammable liquids are used or stored.
22. Use this convector only in the manner, set forth in this manual. Any other use, not recommended
by the manufacturer, can result in a fire, electric shock or injuring of people.
23. By no means clean the convector when it is connected to the mains. Do not submerge the
convector into water. Never pull the power cord.
INSTRUCTION MANUAL

5
Electric convector
24. To prevent overheating and fire, as well as damage of internal electric mains, do not change the
length of the power cord and do not connect the unit through an electric extender. But you can use it
if its parameters comply with the unit's power and if it is don't used by other power energy
consumers.
25. For normal operation of the unit the mains voltage must be sufficient and its technical
parameters must be in strict compliance with technical parameters indicated on the unit. If
necessary, verify characteristics of your mains at the power energy supplier.
26. Install and operate the unit vertically only. It is forbidden to use the unit in a horizontal or inclined
position.
27. The unit must be installed in such a way so that the control panel would be unavailable for a
person, situated directly in a bathroom (in contact with water) or a person taking a shower.
28. It is forbidden to install the unit directly under an outlet or under a laid electric cable when
outgoing heat flows come in contact with it. It may cause their overheating and create an
emergency.
29. The unit is not intended to be used by people (including children) with limited physical, sensory
or intellectual capabilities, having insufficient experience and knowledge, unless they are supervised
or received instructions on how to use the unit from a person, responsible for their safety. It is
necessary to be careful that children do not play with the convector.
ENGLISH

6
Main features
1. Combination of convection effect with soft thermal radiation makes the convector an efficient
source of thermal energy.
2. Simple and effective capabilities for control of the temperature mode.
3. High-precision controllable thermostat.
4. Fast self-repayment thanks to high efficiency and set temperature achievement speed.
5. Simple installation, operational reliability, and easy maintenance.
6. Two-mode heating for electricity saving (except for 1000W models).
7. Supporting legs for installation of the convector in any convenient place.
Specifications
Specifications of the convector are given in Table 1
3. Performance
Principle of operation
Cold air situated in the lower part of the room at the feet level passes through the heating element of
the convection heater. Increasing in volume at the moment of heating, the warm flow rises through
the louvers of the outlet grate and gradually spreads throughout the room. At that, the flow direction
set by inclination of the louvers creates favorable accelerated circulation of warm air inside the room
without its dissipation to walls and windows.
SC HT CM1 1000 WT
SC HT CM1 1500 WT
SC HT CM1 2000 WT
SC HT CL1 1000 WT
SC HT CL1 1500 WT
SC HT CL1 2000 WT
Rated voltage,
V/Hz
Rated current,
A
Rated power,
W
Power modes,
W
Electric protection
class
Dimensions,
mm
Water protection
class
Weight,
kg
Product identification
number
220/50
220/50
220/50
220/50
220/50
220/50
4,6
6,9
9,1
4,6
6,9
9,1
1000
1500
2000
1000
1500
2000
1000
750/1500
1000/2000
1000
750/1500
1000/2000
Table 1
l
l
l
l
l
l
IPX0
IPX0
IPX0
IPX0
IPX0
IPX0
420x440x80
570x440x80
647x440x80
420x440x80
570x440x80
647x440x80
3,1
3,8
4,1
3,1
3,8
4,1
INSTRUCTION MANUAL

7
Electric convector
4. Description
1. Heated air outlet
2. Control panel
3. Supporting legs
4. Cold air inlet
5. Appliance body (front face)
5. Delivery set
1. Convector - 1 pc
2. Supporting legs - 2 pcs
3. Mounting screws for supporting legs - 8 pcs
4. Wall mounting kit - 1 pc
5. Operation manual and warranty certificate - 1 pc
6. Package - 1 pc Fig. 1
1
2
3
5
ENGLISH
4
Уважаемый покупатель!
Благодарим Вас за удачный выбор и приобретение бытового электрического
обогревателя конвекционного типа Scoole. Он прослужит Вам долго.
NOTE:
For improvement of the product quality, the design, specifications, and delivery set of the
convector can be modified by the manufacturer without preliminary notification.
6. Installation
1. Open the original package and carefully take the appliance out.
2. Remove foam plastic seals from edges of the appliance and free it of polyethylene.
3. Take 2 supporting legs from the convector package.
4. Turn over the appliance so that its lower part looks up.

Fig. 2
5. Attach the supporting legs to the lower part of the appliance on the left and right sides so that
mounting holes are aligned with holes on the appliance body (Fig.2).
6. Drive the mounting screws to the available holes applying a sufficient force (Fig.2).
Check security of attachment.
7. Turn the appliance to the right position and place it onto the even
horizontal surface strictly vertically.
The appliance is ready for operation!
8. Also there are included 4 plastic brackets (2 up, 2 low) for wall mounting of the convector in the
scope of delivery. If it is required to use the convector on a wall, you should install the brackets on
the back side of the device. Then fix it by screws that are included in the scope of delivery and hang
the device on a wall.
It is necessary to comply with the minimum distance from objects when you are installing the device.
(Fig.3)
8
Уважаемый покупатель!
Благодарим Вас за удачный выбор и приобретение бытового электрического
обогревателя конвекционного типа Scoole. Он прослужит Вам долго.
WARNING!
The appliance should be operated only with installed supporting legs or mounted on the wall.
Operation of the convector witout the supporting legs or without wall mounting is prohibited!
INSTRUCTION MANUAL
Fig. 3

9
Electric convector
Уважаемый покупатель!
Благодарим Вас за удачный выбор и приобретение бытового электрического
обогревателя конвекционного типа Scoole. Он прослужит Вам долго.
Connection to electric mains
1. The convector is designed for connection to 220V single-phase electric mains.
2. Prior to connection, make sure that parameters of the local electric mains meet the parameters
specified on the nameplate of the appliance.
3. During connection of the convector to the electric mains, it is necessary to observe the effective
electric safety rules.
4. The receptacle should be properly earthed. The receptacle should be designed for rated current
not less than 10A. The receptacle and plug should be always dry to avoid current leakage. Regularly
check that the plug tightly fits the receptacle as follows: a) insert the plug into the receptacle; b)
switch the convector off in half an hour of operation and remove the plug from the receptacle; c)
check by hand whether the plug is hot. If the plug temperature exceeds 50°C, the receptacle should
be replaced by a qualified specialist to avoid damage, accidents, or fire as a result of poor electric
contact.
WARNING!
The receptacle should be designed for rated current not less than 10A, while the electric cable should
have wire section not less than 3x1.5 mm (for copper).²
7. Convector control
Convectors of SC HT СM1 series are equipped with a mechanical thermostat.
Convectors of SC HT CL1 series are equipped with a high-precision electronic thermostat with a
LED-display.
ENGLISH

Operation of SC HT CM1 series electric convectors
1. Switching on
Insert the plug of the power cord to the receptacle to connect the convector to the electric mains.
2. Selection of heating power modes*
Using the power mode switch knob, set the desired heating power: low power ("ECONOMY"), high
power ("EXPRESS").
* - Except for SC HT CM1 1000 WT model
3. Temperature setting
Turn the thermostat knob clockwise up to the stop to the "MAX" position. If the room temperature is
below the set value, "HEATING" indicator should light up. When the room temperature reaches the
desired level, turn the thermostat knob counterclockwise until the appliance switches off.
10
1. Heating power mode switch knob*
This knob is used for selection of the following heating power
modes: low power ("ECONOMY"), high power ("EXPRESS").
2. "POWER" indicator
This indicator lights up upon connection of the appliance to the
electric mains.
3. "HEATING" indicator
This indicator lights up upon switching of heating on.
4. Thermostat knob
This knob is used for setting of the desired temperature in the
room.
* - Except for SC HT CM1 1000 WT, which have one heating power and
use one-key switch
Fig. 4
Control panel for convectors of SC HT CM1 series (Fig. 4)
3
4
2
1
INSTRUCTION MANUAL

“HEATING" indicator will extinguish. Now, the thermostat will maintain the set temperature
periodically switching the convection heater on and off.
The convection heater may incompletely warm up the whole room, especially, in cold weather. In
this case, place the thermostat knob to a level somewhat higher than desired.
4. Switching off
Set the switch knob to the "OFF" position and disconnect the appliance from the electric mains. At
that, "POWER" indicator on the control panel will extinguish.
11
Electric convector
1. "POWER" indicator
This indicator lights up upon connection of the convector to
the electric mains.
2. "HEATING" indicator
This indicator lights up during operation of the convector in
the heating mode.
3. "NORMAL" indicator
This indicator lights up during operation of the convector in
comfortable mode.
4. "TIMER" indicator
This indicator lights up upon activation of the timer function
for switching of the convector off or on.
5. " " button
This button is used to increase the selected value.
Fig. 5
Control panel for convectors of SC HT СL1 series (Fig. 5)
2
3
1
10
9
4
6
7
58
ENGLISH

12 Operation of SC HT СL1 series convectors
1. Switching on the convector
Insert the plug of the power cord to the receptacle to connect the convector to the electric mains.
The "POWER" indicator on the control panel will light up. After that, press the "POWER" button.
2. Selection of heating power modes*
For selection of heating power mode, press the "SET" button three times to display the symbol of
the last set power. Using the " or button, select the necessary heating power. Upon " " "
selection of the low heating power, the display will show "LO" symbol; upon selection of the high
heating power, the display will show "HI" symbol.
* - (except for SC HT CL1 1000 WT model)
3. Temperature setting
3.1. Temperature can be set in the range from +5 to +30°C with 1°C step.
3.2. The factory temperature setting of the comfortable mode is +24°C; the factory temperature
setting of the economic mode is +17 °C.
INSTRUCTION MANUAL
6. "SET" button
This button is used for selection of operation modes, selection of heating power (except for SC HT
CL1 1000WT series), and timer setting.
7. "POWER" button
This button is used for switching of the convector on and off.
8. " " button
This button is used to decrease the selected value.
9. "ECONOMY" indicator
This indicator lights up during operation of the convector in economic mode.
10. LED-display
It displays the temperature value, heating power modes (except for SC HT CL1 1000 WT series),
and timer setting.

13
Electric convector
3.3. To change temperature of the comfortable mode, press the "SET" button once. The "NORMAL"
indicator of the comfortable mode on the control panel will flash. The display will show the flashing
value of the last set temperature. During flashing of the temperature value, press the " " or " "
button to set the desired temperature.
3.4. To change temperature of the economic mode, press the "SET" button twice. The "ECONOMY"
indicator of the economic mode on the control panel will flash. The display will show the flashing
value of the last set temperature. During flashing of the temperature value, press the " " or " "
button to set the desired temperature.
3.5. After setting of the desired temperature, the last set value will be stored and the current
temperature will be displayed.
4. Selection of operation modes
4.1. Press the "SET" button once to select the comfortable operation mode. The "NORMAL"
indicator on the control panel will light up. In this mode, the convector will automatically maintain the
set temperature of the comfortable mode periodically switching heating on and off.
4.2. Press the "SET" button twice to select the economic operation mode. The "ECONOMY"
indicator on the control panel will light up. In this mode, the convector will automatically maintain the
set temperature of the economic mode periodically switching heating on and off.
4.3. Press the "SET" button 4 times (3 times for SC HT CL1 1000 WT series) to select the anti-
freezing mode. The display will show "AF" symbol. The convector will automatically maintain
temperature in the range from +5°C to +7°C periodically switching heating on and off.
5. Setting of timer function for switching off
5.1. During operation of the convector, press the "SET" button 5 times (4 times for SC HT CL1 1000
WT series). The "TIMER" indicator on the control panel will flash. The display will show the flashing
value [0.0] or last set value of the timer.
5.2. Press the button to set the convector switching off time from 0 to 24 hours with " " or " "
1-hour step. The display will show the countdown of time remaining till the moment of the convector
switching off.
5.3. The set time value will be stored and the system will automatically return in 3 seconds to
displaying of the temperature value. The "TIMER" indicator on the control panel will light.
5.4. Upon expiration of the timer setting, the convector will be switched off. The indicators on
ENGLISH

14
the control panel and temperature display will extinguish, but the "POWER" indicator will still light.
5.4. Switching of the appliance off or setting of the timer value [0.0] will cancel the timer function for
the convector switching off.
6. Setting of timer function for switching on
6.1. When the convector is off and only the "POWER" indicator is alight, simultaneously press the
"SET" and buttons. The "TIMER" indicator on the control panel will flash. The display will " "
show the flashing value [0.0].
6.2. Press the button to set the convector switching on time from 0 to 24 hours with " " or " "
1-hour step. The display will show the countdown of time remaining till the moment of the convector
switching on.
6.3. The set time value will be stored. The display will show the set value and the "TIMER" indicator
on the control panel will light.
6.4. Upon expiration of the timer setting, the convector will be switched on to the economic mode
and it will maintain the set temperature.
7. Audible signals
Upon switching on/off and pressing buttons, the convector gives an audible signal.
8. Blocking
8.1. To block the system, simultaneously press and hold the buttons for 3 seconds, " " or " "
when the convector is on. The display will show "[ ]" symbol. In 5 seconds, the symbol will disappear
and the display will show the temperature value. At that, the buttons on the control panel will be
blocked and their pressing will display "[ ]" symbol.
8.2. To unblock the system, press and hold the buttons for 3 seconds or switch the " " or " "
convector off.
9. "RESTART" function
In case of a short-time power interruption, the convector will automatically switch on upon
resumption of power supply and work with the last user settings (except for the timer settings).
10. Switching off
To switch the convector off, press the "POWER" button on the control panel and disconnect the
appliance from the electric mains.
INSTRUCTION MANUAL

15
Electric convector
8. Maintenance
The appliance should be regularly washed to remove dust and contaminations from its outer
surfaces, since it affects the effectiveness of its operation and temperature parameters of space
heating. Prior to the preventive maintenance activities, switch the appliance off and disconnect it
from the electric mains. Let the appliance cool down and then wipe its surface with a slightly
moistened piece of soft cloth. It is not recommended to use cleaning agents for washing including
those with abrasive compositions. Exclude damage of the appliance with sharp items, since
scratches on the painted surface may result in occurrence of rust.
The preventive cleaning procedure should be carried out periodically for maintenance of the
convector technical condition and preservation of its appearance for long years.
ENGLISH

9. Electric circuit diagrams
SC HT СM1 1000WТ models
SC HT СM1 1500WT, SC HT CM1 2000WT models
16
Fig. 6
Fig. 7
INSTRUCTION MANUAL
L
N
L
N
Switcher
Power modes switcher
Thermostat
Thermostat
Heating element
Heating element
Indicator
”HEATING”
Indicator
”HEATING”
Indicator
”POWER”
Indicator
”POWER”

17
Electric convector
Fig. 8
Fig. 9
10. Recycling
Upon expiration of the service life, the convector should be recycled in accordance with the effective
local standards, regulations, and methods. For more details on recycling of the convector, please
contact a representative of the local authority
SC HT CL1 1000WT models
SC HT СL1 1500WT, SC HT CL1 2000WT models
ENGLISH
L
L
N
N
Heating element
Heating element
Programmer
Programmer
Thermal sensor
Thermal sensor

18
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
Бытовой электрический конвектор Scoole предназначен для обогрева и создания комфортной
атмосферы в помещении в холодное время года. Конвектор может быть установлен только в
вертикальном положении в местах, где есть возможность подключения к электропроводке с
однофазным электропитанием 220В. Данный нагревательный прибор удобен и прост в
установке, эффективен и экономичен в использовании в связи с минимальными потерями
электроэнергии, повышенной теплоотдачей и максимально комфортным распределением
теплового потока.
1. Важная информация
Просим внимательно ознакомиться с руководством по эксплуатации перед использованием
конвектора.
В данном руководстве по эксплуатации содержится важная информация, касающаяся Вашей
безопасности, а также рекомендации по правильному использованию прибора и уходу за ним.
Сохраните руководство по эксплуатации, вместе с гарантийным талоном, кассовым чеком, и,
по возможности, картонной упаковкой и упаковочным материалом.
Приобретенный Вами конвектор может несколько отличаться от описанного в руководстве,
что не влияет на способы его использования и эксплуатации.
Важные меры предосторожности и инструкции, содержащиеся в данном руководстве, не
включают всех возможных режимов и ситуаций, которые могут встречаться. Необходимо
понимать, что здравый смысл, осторожность и тщательность являются факторами, которые
невозможно «встроить» ни в один продукт.
Эти факторы должен учитывать человек, который заинтересован в надлежащей эксплуатации
устройства. Изготовитель не несет ответственности в случае повреждения прибора или его
отдельных частей во время транспортировки, в результате неправильной установки, в
результате колебаний напряжения, а также в случае, если какая-либо часть прибора была
изменена или модифицирована.
Уважаемый покупатель!
Благодарим Вас за удачный выбор и приобретение бытового электрического конвектора Scoole.
Он прослужит Вам долго.

19
РУССКИЙЭлектрический конвектор
2. Меры предосторожности
При использовании конвектора, необходимо соблюдать ряд мер предосторожности.
Неправильная эксплуатация в силу игнорирования мер предосторожности может привести к
причинению вреда здоровью пользователя и других людей, а также нанесения ущерба их
имуществу.
1. Прочитайте все инструкции перед использованием конвектора.
2. Конвектор при работе нагревается до очень высокой температуры. Чтобы избежать ожогов,
не прикасайтесь руками и другими частями тела к горячим поверхностям прибора.
3. Прибор должен располагаться вдали от легковоспламеняющихся и легкодеформируемых
объектов.
4. Удостоверьтесь, что корпус прибора и его нагревательный элемент остыл, прежде чем
прибор будет демонтирован и уложен в упаковку для длительного хранения.
5. Когда прибор не используется долгое время, храните его в сухом прохладном месте в
заводской картонной упаковке.
6. НЕ НАКРЫВАЙТЕ ПРИБОР, когда он работает. Не сушите на нём одежду и любые другие
ткани и материалы. Это может привести к его перегреву, выходу из строя или причинить
значительный ущерб Вам и/или Вашему имуществу.
7. Прибор всегда должен находиться под наблюдением, особенно если неподалеку от
прибора находятся дети. Внимательно следите за тем, чтобы дети не прикасались к прибору
руками.
8. Всегда отключайте конвектор от электрической сети, когда он не используется.
9. Прибор оснащен евровилкой с контактом заземления. Вилка должна подходить к
стандартной евророзетке и входить в нее без особых усилий. Если вилка не входит в розетку
или входит туго, переверните ее по вертикали на 180 градусов и повторите попытку.
Уважаемый покупатель!
Благодарим Вас за удачный выбор и приобретение бытового электрического
обогревателя конвекционного типа Scoole. Он прослужит Вам долго.
ВНИМАНИЕ!
Производитель рассматривает данный вид поломки, как негарантийный случай.

20
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
Если и после этого Вы не можете легко вставить вилку в розетку, вызовите электрика, для
замены розетки. Никогда не используйте прибор, если вилка вставлена в розетку не до конца.
10. Никогда не подключайте прибор к электросети, если его поверхность влажная (мокрая).
11. Никогда не используйте прибор в ситуации, когда он может соприкасаться с водой.
12. Когда прибор включен и работает, не касайтесь его поверхности и поверхности блока
управления мокрыми руками и любыми частями тела.
13. Не включайте конвектор, если его сетевой шнур или вилка имеют повреждения. Во
избежание опасности поражения электрическим током, поврежденный сетевой шнур должен
меняться только в авторизованных сервисных центрах изготовителя, квалифицированными
специалистами.
14. Никогда не пытайтесь производить ремонт конвектора самостоятельно. Это может
причинить вред Вашему здоровью и повлиять на гарантийное обслуживание прибора.
15. Не используйте конвектор на открытых пространствах вне помещения.
16. Запрещено устанавливать и использовать прибор в ванных комнатах, душевых или
бассейнах, именно в тех местах, где есть вероятность прямого попадания струй и капель
воды на его поверхность во время, когда прибор включен.
17. Не прокладывайте сетевой шнур конвектора под ковровыми покрытиями и не прижимайте
его предметами мебели. Прокладывайте сетевой шнур так, чтобы об него невозможно было
споткнуться.
18. Для выключения прибора серии SC HT CM1 установите переключатель сбоку на панели
управления в положение «OFF», а для серии SC HT CL1 нажмите кнопку «POWER» на панели
управления и отсоедините вилку сетевого шнура от розетки. Никогда не тяните за сетевой
шнур и не отсоединяйте вилку резко.
19. Не просовывайте пальцы и исключите попадание посторонних предметов в какие-либо
вентиляционные, воздухозаборные или выходные отверстия, так как это может привести к
поражению электрическим током или повреждению конвектора.
20. Для предотвращения возможного пожара не загораживайте ничем воздухозаборные и
выходные отверстия. Не вешайте и не сушите вещи на конвекторе! Используйте конвектор
только на ровной сухой поверхности.