Seco SANTINO 7.0 OF PCT User manual
Product Manual
SANTINO 7.0 OF PCT
Arm®Cortex®-A9 Rear Mount
2
PRODUCT MANUAL
SANTINO
Document Revision History
The information in this document is subject to change without prior notice in order to improve reliability, design and
function and does not represent a commitment on the part of the manufacturer.
Online support on edge.seco.com
Revision Date Author Description
V 1 10.02.2017 CG Initial Release
V 2 06.10.2017 CG Mechanical modications
V 3 15.03.2018 CG Page 18 New Picture RS485 Pin 6 to 11
V 4 04.12.1018 CG Page 17 add Text for Pin1, Page 15 add new
Capitle 5.2 " connecting the HMI device"
V 5 26.08.2019 CG Change address
V 6 17.12.2021 bmy SECO CI Update 2022
PRODUCT MANUAL
SANTINO
Table of Contents
1. Introduction .........................................................................................4
2. Safety Hints .........................................................................................5
3. Product Introduction ..........................................................................6
3.1 Type Plate and Device Information ..............................................................6
3.2 Product names and variants.........................................................................7
3.3 Related Documents and Online Support....................................................8
4. Technical Data .....................................................................................9
4.1 Block Diagram SBC .......................................................................................11
4.2 Connectors......................................................................................................12
5. Installation and Start Up .....................................................................14
5.1 Connection Scheme ......................................................................................14
5.2 Connecting the HMI device ..........................................................................15
6. Internal and External Interfaces.........................................................16
6.1 GND Shield Connector (X122).....................................................................16
6.2 Ethernet (X118) ..............................................................................................16
6.3 Power (X1).......................................................................................................17
6.4 DIP Switch (SW3)...........................................................................................17
6.5 CAN/RS-485 Interface (X39)........................................................................18
6.6 Speaker (X9)...................................................................................................19
6.7 Keypad/SPI (X106).........................................................................................20
6.8 RS-232/RS-232 (X13)....................................................................................21
6.9 USB Host (X34) ..............................................................................................22
6.10 USB OTG (X20) ..............................................................................................22
6.11 SD Card Reader (X31) ..................................................................................22
6.12 Reset Switch (SW1) .......................................................................................23
6.13 Bootselect Switch (SW2) ..............................................................................23
6.14 Power LED (D30)............................................................................................23
6.15 Battery-Holder (X2)........................................................................................24
7. Battery .................................................................................................25
7.1 BatterySpecications....................................................................................25
7.2 Replacement of the Internal Battery ...........................................................26
Annex A: Technical Drawing...............................................................................27
Annex B: Hardware Revision Information .........................................................28
Annex C: Assembly Options ............................................................................... 29
C-1 Wi-Fi / Bluetooth .............................................................................................29
Annex D: Guidelines and Standards .................................................................30
D-1 RoHS Declaration...........................................................................................30
D-2 Supplier Declaration – Directive EG 1907/2006 REACH..........................30
D-3 ULCertication...............................................................................................30
D-4 SECO Northern Europe Conformity Statement.........................................31
Annex E: Common Documentation....................................................................32
E-1 Warranty Hints ................................................................................................32
E-2 Field of Application.........................................................................................33
Annex F: Technical Support ..............................................................................34
Annex G: General Information............................................................................35
* alternative assembly upon request
4
PRODUCT MANUAL
SANTINO
1. Introduction
Thank you very much for purchasing a SECO Northern Europe product. Our products are dedicated to professional
use and therefore we suppose extended technical knowledge and practice in working with such products.
The information in this manual is subject to technical changes, particularly as a result of continuous
product upgrades. Thus this manual only reflects the technical status of the products at the time
of printing. Before design-in the device into your or your customer’s product, please verify that this
document and the therein described specication is the latest revision and matches to the PCB
version. We highly recommend contacting our technical sales team prior to any activity of that kind.
The attached documentation does not entail any guarantee on the part of SECO Northern Europe
GmbH with respect to technical processes described in the manual or any product characteristics
set out in the manual. We do not accept any liability for any printing errors or other inaccuracies in
the manual unless it can be proven that we are aware of such errors or inaccuracies or that we are
unaware of these as a result of gross negligence and
SECO Northern Europe has failed to eliminate these errors or inaccuracies for this reason.
SECO Northern Europe GmbH expressly informs that this manual only contains a general
description of technical processes and instructions which may not be applicable in every individual
case. In cases of doubt, please contact our technical sales team.
In no event, SECO Northern Europe is liable for any direct, indirect, special, incidental or
consequential damages arising out of use or resulting from non-compliancy of therein conditions
and precautions, even if advised of the possibility of such damages.
Before using a device covered by this document, please carefully read
Annex „E-1 Warranty Hints“
Annex „E-2 Field of Application“
Embedded systems are complex and sensitive electronic products. Please act carefully and ensure
that only qualied personnel will handle and use the device at the stage of development. In the
event of damage to the device caused by failure to observe the hints in this manual and on the
device (especially the safety instructions), SECO Northern Europe shall not be required to honour
the warranty even during the warranty period and shall be exempted from the statutory accident
liability obligation. Attempting to repair or modify the product also voids all warranty claims.
5
PRODUCT MANUAL
SANTINO
2. Safety Hints
Please read this section carefully and observe the instructions for your own safety and correct use of the device.
Observe the warnings and instructions on the device and in the manual. SECO Northern Europe embedded
systems have been built and tested by us and left the company in a perfectly safe condition.In order to maintain this
condition and ensure safe operation, the user must observe the instructions and warnings contained in this manual.
I. General Handling
Don’t drop or strike the unit: The PCB, display and/or other parts might be damaged.
Keep away from water and other liquids, the unit is not protected against.
Operate the unit under electrical and environmental conditions according to the technical
specication.
The electrical installations in the room must correspond to the requirements of the local (country-
specic) regulations.
Take care that there are no cables, particularly power cables, in areas where persons can trip over
them.
Do not place the device in direct sunlight, near heat sources or in a damp place.
All plugs on the connection cables must be screwed or locked to the housing.
Repairs may only be carried out by qualied specialist personnel authorized by
SECO Northern Europe GmbH or their local distributors.
Maintenance or repair on the open device may only be carried out by qualied personnel
authorized by SECO Northern Europe GmbH which is aware of with the associated dangers.
II. Electricity
The embedded systems may only be opened in accordance with the description in this user’s
manual for
- replacing of the (rechargeable, where applicable) lithium battery and/or
- conguration of interfaces, where applicable
These procedures have to be carried-out only by qualied specialist personnel.
When accessing internal components the device must be switched off and disconnected from the
power source.
When purchased core or basic versions without protecting back cover, don’t touch the PCB directly
with your ngers. Especially these products need to be handled very carefully.
Don’t operate or handle the unit without typical ESD protection measures, such as ground
earthing.
Operate the unit according to the technical specication only.
III. Damage or Permanent Malfunction
It must be assumed that a safe operation is no longer possible, in case
-the device has visible damage or
-the display is dark or shows strange pattern for longer period
-the device doesn’t react after a reset
In these cases the device must be shut down and secured against further use
IV. LCD and touch handling
If equipped with, the soft surface of a resistive touch screen is not suitable for use with stencils
and/or other devices for touch operation. There are special plastics pens available in commercial
shops. A projective capacitive touch screen might be protected by a heat strengthened glass or
acrylic or polycarbonate cover lens. These are dedicated for use with nger tips. There are very
special pens available which might work with a PCT touch.
Protect the LCD/touch/cover lens against scratches and sharp edges. The warranty does not cover
pixel failures resulting from non-compliant handling.
Clean the LCD/touch/cover lens with a soft cotton cloth with alcohol. Don’t use organic solvents,
acid or alkali solutions.
Water drops, nger fat or any similar fouling should be removed immediately from the LCD, cover
lens and metal frame to avoid any staining.
6
S/N: YY-WW
Made in Germany
25,4
50,5
Art.No.: 900-0000R
Model: SANTINO x1
9-32 V ; 2,3-0,65 A
S/N: YY-WW
Made in Germany
25,4
50,5
Art.No.: 900-0000R
Model: SANTINO x1
9-32 V ; 2,3-0,65 A
PRODUCT MANUAL
SANTINO
3. Product Introduction
This document is applicable for hardware revisions 1.0 or later of the SANTINO series.
Please nd the hardware version grid in „Annex B: Hardware Revision Information“:
SANTINO is an Embedded System to be used as human machine interface (HMI) in various applications. Please
refer to Annex „E-2 Field of Application“ for further information. The system is equipped with a large number of
industrial interfaces. A wide variety of options is available as well.
3.1 Type Plate and Device Information
For service and later identication of the device, the type plate contains important information.
Position of Typelabel
SECO Northern Europe article number
Product name and conguration
Serial number
Power ratings
Production date (week/year)
(Exemplary Illustration. It shows the SANTINO 7.0" BX PCT.)
7
PRODUCT MANUAL
SANTINO
3.2 Product names and variants
Product name denition:
SANTINO <CPU> <7.0> <OF> <PCT> <IPS> <additional description> <Vx.y.z>
Explanation:
SANTINO Product family name (invariable)
<CPU> x1, x2L (number of cores inside the i.MX6 processor)
<7.0> Display size in inch
<OF> <SG> <BX> mechanical design of enclosure
<PCT> projected capacitive touch; if blank: 4-wire resistive
<IPS> Display technology “in-plane switching”, (option)
<additional description> contains variants which are important to sales product description, i.e.
without or with WLAN/Bluetooth module (“W/B”)
untreated glass surface or including antiglare treatment (“AG”)
front frame made from die-cast zinc or aluminium (“Alu”)
different memory capacities for RAM and/or eMMC
customer-specic reduced assembly
etc.
<Vx.y.z> revision of PCB layout
<x> describes major changes in form t and functions
<y> describes variants that are different in PCB layout and could affect the list of
critical components (UL LoCC).
<z> describes minor changes to PCB layout due to production optimization like
solder resist mask or drilling diameters.
Also minor changes in assembly of PCB and/or device which do NOT affect the
list of critical components (UL LoCC) due to unlisted components or declared
“interchangeable”.
Flash-N-Go
https://bit.ly/3pmwWo4
Contains information about the usage of the G&F Flash-N-Go solution
which consists of three submodules:
Flash-N-Go Boot (A tiny boot loader)
Flash-N-Go System (A maintenance os)
Flash-N-Go Update (A GUI based update solution for all os)
Linux Yocto Jethro
https://bit.ly/3DjEihg
Contains information about Linux BSP with development environment
Linux Embedded System Yocto (Codename: Jethro, Version 3.0) includes
rst information about the bootloader Flash-N-Go
Linux Yocto Rocko
https://bit.ly/3xNQKVc
Android 7.1
https://bit.ly/3de2N4H
8
PRODUCT MANUAL
SANTINO
3.3 Related Documents and Online Support
This document contains operating system specic information. The following additional documentations are
available:
OPERATING SYSTEMS
UPDATE / BOOT / SYSTEM
CPU x1 x2L
CPU Type i.MX6Solo i.MX6DualLite
Core Class Arm®Cortex®-A9
Core Clock 1 GHz
Features
NEON for SIMD media acceleration and VFP operations; Multi-format HD 1080p
video decoder and HD 720p video encoder hardware engine; L1 cache, 32 KB for
instruction, 32 KB for data; 512 KB L2 cache
HW Accelerators OpenGL ES 2.0, OpenVG 1.1
RTC Accuracy: +/- 30 ppm at 25°C
Memory
eMMC Flash 4 GB MLC eMMC
RAM Standard 512 MB 32 bit DDR3L 1 GB 32 bit DDR3L
SD Card Slot 4 bit MMC/SDIO/SD/SDHC
Operating Systems
Supported OS Linux Yocto Jethro
Communication Interfaces
Network 1x 10/100 Mbit/s Ethernet (RJ-45)
USB 2.0 1x 480 Mbit/s Host (Type A)
1x 480 Mbit/s OTG (Type Micro-AB) 1
CAN Fieldbus/ RS-485 1x CAN (ISO/DIS 11898) + 1x RS-485 1x CAN (ISO/DIS 11898) + 1x RS-485
galvanic isolated
RS-232 2x RS-232 (RX/TX/CTS/RTS)
MDB 2/1x MDB (Master / Slave optional) 3instead of 2nd external RS-232
Synchronous
Serial Interfaces I²C, Matrix keypad up to 4 x 4
Audio
Speaker output 1x speaker (connector), 1.5 W RMS (8Ω)
9
PRODUCT MANUAL
SANTINO
4. Technical Data
1Mechanically the Micro-USB interface has not been designed for frequent contact operations. Please use an
adapter cable with a strain relief.
2Option
3The selection of a variant eliminates the other.
Audio Internal 1x speaker 0.3 W RMS (8Ω) parallel to external output
Display and Touch
Size 7.0 inch / 177.8 mm
Resolution 800 x 480 pixel
Brightness Typ. 400 cd/m2
Backlight Lifetime Typ. 50.000 h
Viewing Angle 50°, 70°, 70°, 70°(UDRL)
Color 18 bit (262 K colors)
Touch projected capacitive multi touch
Housing x1 x2L
10
PRODUCT MANUAL
SANTINO
Front 1.1 mm toughened glass
Frame None
Rear ABS-PC/1.4016 stainless steel
Ingress Protection Front IP 20/Rear IP20
Device Dimensions
W x H x D 185.1 x 101.6 x 33.28 mm
Weight tbd.
Power Supply
Supply Voltage Nom. 9 to 32 V DC
Consumption Typ. 5.3 W; max. 22.8 W
Internal Backup Battery (RTC) Type: 3 V Li-Ion Type CR1220:
Lifetime (RTC only): Approximately 8 years, depending on application
Typical Environmental Conditions
Storage Temp. -20 to +70 °C
Operating Temp. 0 to +60 °C
Humidity 5 to 90 % RH
Max. Operating Altitude ty 3.000 m
Max. Storage/Transit Altitude 10.000 m
Noise Level [db(A)] @ 1m <<40 (fanless design)
Lifetime
MTBF ≥400.000 h (without backlight)
11
2x Speaker
2-pole JST
RJ-45
Jack
Audio
Amplifier
Ethernet
Phy
USB
Type A
Block Diagram SANTINO
i.MX6
Keypad
10-pole JST USB-OTG
Micro AB
SD-Card
Connector
I2C-3
USB H1
USDHC4
DRAM
eMMC
DDR3
Audio
Codec
Keypad
port
AUD4
MDIO/RMII
Res.Touch
4-pole FFC
SD2
RGB 1x RGB
666
Backlight
40-pole FFC
PWM1
5V Supply
USB OTG
Touchscreen
Controller
Cap.Touch
6-pole Molex
24 V
2-pole Phoenix Step Down
Converter
PMIC Power
Battery
RTC
Battery
CR1220
RC 1
FlexCAN-1
UART-1
CAN/RS-485
12-pole Molex
Galv. Isol.
x2L
CAN
Transc.
CAN
Transc.
RS-485
Transc.
FlexCAN-2
RS-232/MDB
10-pole Molex
RS-232
Transceiver
RS-232
Transceiver
UART-2
UART-5
MDB
PRODUCT MANUAL
SANTINO
4.1 Block Diagram SBC
Pos. Description
1GND Shield connector (X122)
2Ethernet (X118)
3Power (X1)
4CAN/RS-485 Interface (X39)
optional with galvanic isolation
5 Speaker (X9)
6Keypad/Capacitive Touch (X106)
7RS-232/MDB (X13)
8USB Host (X34)
9USB OTG (X20)
10 Battery (X2/X112)
11 Dip Switch for RS485/CAN (SW3) 12
L171
PRODUCT MANUAL
SANTINO
4.2 Connectors
(Exemplary Illustration. It shows the fully equipped SANTINO Dualcore light 7.0" BX PCT.)
As this manual describes an open frame version, only the external interfaces will be mentioned in the following
chapter.
Pos. Description
12 Reset Switch (SW1)
13 Bootselect Switch (SW2)1
14 SD card reader (X31)
15 Power LED (D30)
13
PRODUCT MANUAL
SANTINO
(Exemplary Illustration both sides)
1For the function of this switch please refer in the future to the Flash N Go User Manual.
Pos. Description
1
Ethernet
2
DC in
3
RS-232
4
USB-Device
5
USB Host (OTG)
Pos. Description
6
Reset sw
7
Bootselect sw
8
SD card slot
9
Power LED
Exemplary Illustration
14
Ethernet (TCP/IP) via
cross over cable or switch
USB Accessory
Memory stick,
mouse
USB (Active Sync)
to PC / Development
RS-232 (Serial)
Debug-PC / Periphery
SD/SDHC
USB-OTG2x RS232
SPI/Keypad
SpeakerCAN/RS485Power
LAN USB-Host
L171
PRODUCT MANUAL
SANTINO
5. Installation and Start Up
The content of this document is limited to explain the device connectors and how to access SANTINO via FTP over
your local area network (LAN) within a few seconds. For advanced hardware specications and software support,
please refer to chapter „3.3 Related Documents and Online Support“
5.1 Connection Scheme
http://support.garz-fricke.com/projects/Santino/
Notice
An incorrectly dimensioned power supply can destroy the HMI device.
Use a DC power supply with adequate amperage; see Chapter 4. Technical Data
Notice
Safe electrical isolation
For the DC supply, use only power supply units with safe electrical isolation in accordance with IEC 60364-4-41 or HD
384.04.41 (VDE 0100, Part 410), e.g. conforming to the SELV/PELV standard.
The supply voltage must be within the specied voltage range. Otherwise, malfunctions at the HMI device cannot be
ruled out.
Applies to non-isolated system congurations:
Connect the GND connection from the DC power supply output to equipotential bonding for uniform reference potenti-
al. You should always select a central point of termination.
Notice
We recommend using cables with the following specications
Function Cable specication
DC supply No special requirements
Audio No special requirements; length < 3m
Ethernet Shielded, type CAT5e SFTP
RS485 Shielded data cable
RS232 Shielded data cable, length <30m
CAN Shielded data cable
USB Shielded USB cable; labeled as “Certied HI-SPEED USB
2.0”; length <3m
15
PRODUCT MANUAL
SANTINO
5.2 Connecting the HMI device
Pin Name Description Information
1Tx+
Rx/Tx might be swapped
(Auto-MDIX)
+/- might be swapped
(Autom. polarity correction)
2TX-
3RX+
4SPARE 1
5
6RX-
7SPARE 2
8
Header: RJ45
Pin Name Description Information
1GND Ground shield
6.3 mm spade terminal
16
1
1
PRODUCT MANUAL
SANTINO
6. Internal and External Interfaces
6.1 GND Shield Connector (X122)
6.2 Ethernet (X118)
Green LED (link) is default off and turns on when link is detected.
Yellow LED (act) flashes during sending/receiving packets.
Pin Name Description Level
1GND DC Ground 0 V
2Vcc_In DC Input voltage Nom. 9 to 32 V DC
Header: Molex 43045-0200 Micro-Fit 2p
Plug: Molex 43025-0200 Micro-Fit 2p,
crimp contact Molex 43030-0007
Shielding with 6,3 mm male spade terminal connector.
Pin 1 (GND) is connected to frame/housing. GND/Vcc_In is not galvanic isolated from System-GND
Switch Function Description
1/2 RS485 Half Duplex Switch on for Half Duplex
3RS485 Termination Switch on for termination
4/5 CAN Termination Switch on for termination
X1
MO LEX_43045-0200_Micro-Fit_02p
DC_IN/DC_IN_ISO/AC_IN/AC_IN_ISO/DC_IN_5P0
1 2
TP314
TP315
C971
10N/500V X7 R 10% 1206
TP319
RV 1
S10K30
DC_IN/DC_IN_ISO/AC_IN/AC_IN_ISO
TP320
F2
5A_Nano_Slo-Blo_Typ-454
DC_IN/DC_IN_ISO/AC_IN/AC_IN_ISO/DC_IN_5P0
1 2
R667
1M00 5% 1206 HV
17
1
1
PRODUCT MANUAL
SANTINO
6.3 Power (X1)
6.4 DIP Switch (SW3)
Caution:
Power supplies connected to this device must be compliant to the requirements of
“limited power sources” (LPS) to prevent the end-user from danger in case of a fault.
Pin Name Description Level
1GND_CAN_RS485 Ground Shield
2CAN1_TERM To enable CAN1-Termination, bridge with CAN1_H
3CAN1_H CAN bus 1 high -24 +24 V
4CAN1_L CAN bus 1 low -24 +24 V
5CAN1_TERM To enable CAN1-Termination, bridge with CAN1_L
6RS485_TERM To enable RS485-Termination: bridge with RS485_A
7GND_CAN_RS485 Ground for CAN and RS485 group
8n.a.
9RS485_Y TX+ -7 +12 V
10 RS485_Z TX- -7 +12 V
11 RS485_A RX+, to enable Half-Duplex: bridge with RS485_Y
12 RS485_B RX- ,to enable Half-Duplex: bridge with RS485_Z
Header: Molex 43045-1200 Micro-Fit 12p
Plug: Molex 43025-1200 Micro-Fit 12p, crimp contact Molex 43030-0007
Shielding with 6,3 mm male spade terminal connector
Pin Name Description Level
1-5 Identical to standard
6n.a.
7GND_CAN_RS485 Ground for CAN group
8CAN2_TERM To enable CAN2-Termination, bridge with CAN2_H
9CAN2_H CAN bus 2 high -24 +24 V
10 CAN2_L CAN bus 2 low -24 +24 V
11 CAN2_TERM To enable CAN2-Termination, bridge with CAN2_L
12 n.a.
18
1
7
1
7
1
7
1
7
1
7
1
7
1
7
PRODUCT MANUAL
SANTINO
6.5 CAN/RS-485 Interface (X39)
CAN1 / CAN2 *
* alternative assembly upon request
CAN1 Termination
RS485 Termination
RS485 Half-Duplex
CAN1 Termination
CAN2 Termination
Pin Name Description Level
1Speaker + Parallel to X10 1.5W RMS 8 Ohm
2Speaker -
Header: JST S2B-PH-SM3-TB
Plug: ST PHR-2 with crimp contacts SPH-002GW-P0.5L-ND
19
PRODUCT MANUAL
SANTINO
6.6 Speaker (X9)
1
Pin Name Description
Default Mode Level
1Power Supply 100 mA
2GND Ground
3.3 V
3PCK0_GPIO6_7 Keypad row 0
4PCK1_GPIO6_8 Keypad column 0
5PCK2_GPIO6_9 Keypad row 1
6PCK3_GPIO6_10 Keypad column 1
7PCK4_GPIO6_11 Keypad row 2
8PCK5_GPIO6_15 Keypad column 2
9I2C1_SDA I²C data
10 I2C1_SCL I²C clock
Header: JST DF20F-10DP, side entry, RM = 1.00
Plug: JST DF20-10DS-1C, crimp contact: DF20 F2830 SCF A
Drive Strength
(Software dened) I_OL (mA) I_OH (mA)
Low 5.1 -5.1
Medium 10.2 -10,2
High 15.3 -15,3
20
-
5P0
I2C1_SDA{3,6,8}I2C1_SCL {3,6,8}
X106
HIROSE_DF20F-10DP-1H
1 2
3 4
5 6
7 8
910
M2
M1
D89
ESDALC6V1W5/SOT323_5
1 5
2
3 4
D87
ESDALC6V1W5/SOT323_5
1 5
2
3 4
PCK0_GPIO6_7
PCK2_GPIO6_9
I2C1_SDA I2C1_SCL
PCK4_GPIO6_11
PCK1_GPIO6_8
PCK3_GPIO6_10
PCK5_GPIO6_15
2
1
PRODUCT MANUAL
SANTINO
6.7 Keypad/SPI (X106)
Keypad/SPI/I²C, multiplexed
Digital output Specication (3.3 V):
V_OH: min OVDD-0.15; V_OL max: 0.15V
Table of contents
