Seneca ZE-4DI-2AI-2DO User manual

MI00582-0-EN INSTALLATION MANUAL 1/6
INSTALLATION MANUAL
SENECA s.r.l.; Via Austria, 26 – 35127 – PADOVA – ITALY; Tel. [phone] - Fax [phone]
WARNING: The full content of this manual must be read before any operation. The module must only be used by
qualied electricians. Specic documentation is available via QR-CODE shown on page 1.
Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling).
The symbol on the product or its packaging shows the product must be surrendered to a collection centre
authorized to recycle electrical and electronic waste.
The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to
electrostatic discharges. Take appropriate measures during any operation.
PRELIMINARY WARNINGS
The word WARNING preceded by the symbol indicates conditions or actions that put the user's safety at risk.
The word ATTENTION preceded by the symbol indicates conditions or actions that might damage the
instrument or the connected equipment. The warranty shall become null and void in the event of improper use or
tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if
the instructions contained in this manual are not followed.
CONTACT INFORMATION
Technical support [email protected] Product information [email protected]
This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised.
The content of this document corresponds to the described products and technologies.
Stated data may be modied or supplemented for technical and/or sales purposes.
ZE-4DI-2AI-2DO
Z-4DI-2AI-2DO
ZE-2AI
DOCUMENTATION
ZE-4DI-2AI-2DO
DOCUMENTATION
Z-4DI-2AI-2DO
DOCUMENTATION
ZE-2AI

MI00582-0-EN INSTALLATION MANUAL 2/6
MODULE LAYOUT
17.5 mm 111 mm
102.5 mm
35 mm
LED SIGNALS ON THE FRONT PANEL (ZE-4DI-2AI-2DO)
LED STATUS MEANING
IP / PWR ON Module powered IP address acquired
IP / PWR Flashing Module powered Waiting for IP address from the DHCP server
Tx/Rx Flashing Data transmission and reception on at least one Modbus port
ETH TRF Flashing Packet transmission on Ethernet port
ETH LNK ON Ethernet port connected
DI1, DI2, DI3, DI4 On / Off Status of digital input 1, 2, 3, 4
DO1, DO2 On / Off Status of output 1, 2
FAIL Flashing Outputs in fail condition
LED SIGNALS ON THE FRONT PANEL (Z-4DI-2AI-2DO)
LED STATUS MEANING
PWR ON Module powered
Tx/Rx Flashing Data transmission and reception on at least one Modbus port:
COM 1 port, COM 2 port
DI1, DI2, DI3, DI4 On / Off Status of digital input 1, 2, 3, 4
DO1, DO2 On / Off Status of output 1, 2
FAIL Flashing Outputs in fail condition
LED SIGNALS ON THE FRONT PANEL (ZE-2AI)
LED STATUS MEANING
IP / PWR ON Module powered and IP address acquired
IP / PWR Flashing Module powered Waiting for IP address from the DHCP server
FAIL ON At least one of the two analogue inputs is out of scale (underscale-overscale)
ETH TRF Flashing Packet transmission on Ethernet port
ETH LNK ON Ethernet port connected
Tx1 Flashing Modbus packet transmission from device to COM 1 port
Rx1 Flashing Modbus packet reception on COM 1 port
Tx2 Flashing Modbus packet transmission from device to COM 2 port
Rx2 Flashing Modbus packet reception on COM 2 port
Single module dimensions LxHxD: 17.5 x 102.5 x 111 mm; Weight: 110 g; Enclosure: PA6, black
Double module dimensions LxHxD: 35 x 102.5 x 111 mm; Weight: 110 g; Enclosure: PA6, black
ZE-4DI-2AI-2DO ZE-2AI
Z-4DI-2AI-2DO

MI00582-0-EN INSTALLATION MANUAL 3/6
TECHNICAL SPECIFICATIONS
CERTIFICATIONS
https://www.seneca.it/products/ze-4di-2ai-2do/doc/CE_declaration
https://www.seneca.it/products/z-4di-2ai-2do/doc/CE_declaration
https://www.seneca.it/products/ze-2ai/doc/CE_declaration
INSULATION
ENVIRONMENTAL
CONDITIONS
Temperature: -25 ÷ + 70°C
Humidity: 30% ÷ 90% non condensing
Altitude: Up to 2000 m above sea level
Storage temperature: -30 ÷ +85°
Protection rating: IP20.
ASSEMBLY IEC EN60715, 35mm DIN rail in vertical position.
CONNECTIONS
Removable 3-way screw terminals, 5 mm pitch for cable up to 2.5 mm2
Rear connector IDC10 for DIN bar 46277
RJ45
micro USB (Z-4DI-2AI-2DO)
POWER SUPPLY
Voltage: 11 ÷ 40Vdc; 19 ÷ 28Vac 50 ÷ 60Hz
Absorption: Typical: 1,5 W @ 24Vdc, Max: 4 W (ZE-4DI-2AI-2DO Z-4DI-2AI-2DO)
Absorption: Typical: 1,5 W @ 24Vdc, Max: 2 W (ZE-2AI)
DIGITAL
INPUTS
only
ZE-4DI-2AI-2DO
Z-4DI-2AI-2DO
Number of channels 4. Congurable PNP or NPN.
Voltage input OFF < 4V, ON > 8V (max. 24 Vdc ). Current input 20 mA.
Max frequency 5 KHz.
Absorbed current 3mA@12Vdc, 10mA @24Vdc.
COUNTERS
only
ZE-4DI-2AI-2DO
Z-4DI-2AI-2DO
4 32bit resettable counters on non-volatile memory.
DIGITAL
OUTPUTS
only
ZE-4DI-2AI-2DO
Z-4DI-2AI-2DO
Number of channels 2. SPDT free contact relay.
Max. voltage 250Vac. Max. current 2 A.
ANALOGUE
INPUTS
Number of channels 2. Voltage/Current congurable
Input Voltage 0÷30 V. Precision 0.1% of full scale, Resolution: 16 bit
Current input 0 ÷ 20mA– precision 0.1% of full scale, Resolution: 16bit
Input protection 40V / 25mA
COMMUNICATION
PORTS
RS485 COM1 on IDC10 connector. RS485 or RS232 M10-M11-M12.
Ethernet 100 base T RJ45 front (ZE-4DI-2AI-2DO, ZE-2AI)
side micro USB port (Z-4DI-2AI-2DO)
Power
Supply
Input Output
1500 V~
0030 V ~
584SR
RS485
RS232
DI 1
DI 2
DI 3
DI 4
AI 1
AI 2
DO 1
DO 2
Power
Supply
Input Output
1500V~
0030 V~
BSU
584S
R
RS485 RS232
DI 1
DI 2
DI 3
DI 4
AI 1
AI 2
DO 1
DO 2
Power
Supply
Input
1500V~
584SR
RS485 RS232
AI 1
AI 2
ZE-4DI-2AI-2DO Z-4DI-2AI-2DO ZE-2AI
ZE-4DI-2AI-2DO Z-4DI-2AI-2DO ZE-2AI
ETH
ETH
ETH

MI00582-0-EN INSTALLATION MANUAL 4/6
FACTORY IP ADDRESS
The default module IP address is static: 192.168.90.101
WEB SERVER
To access the maintenance Web Server with 192.168.90.101 factory IP address:
Default user: admin, Default password: admin, http://192.168.90.101
INSTALLATION REGULATIONS
The module has been designed for vertical installation on a DIN 46277 rail. For optimal operation and long life,
adequate ventilation must be provided. Avoid positioning ducting or other objects that obstruct the ventilation slots.
Avoid mounting modules over heat-generating equipment. Installation in the bottom part of the electrical panel is
recommended.
These are open type devices intended for installation in a nal casing/panel that offers mechanical protection and
protection against the spread of re.
CAUTION
ModBUS CONNECTION RULES
1) Install the modules in the DIN rail (120 max)
2) Connect the remote modules using cables of an appropriate length. The following table shows cable length data:
-Bus length: maximum length of the Modbus network according to the Baud Rate. This is the length of the cables
that connect the two farthest modules (see Diagram 1).
- Derivation length: maximum length of a derivation 2 m (see Diagram 1).
Lunghezza
bus
Lunghezza
derivazione
1200 m 2 m
Schema 1
Modulo 2Modulo 1
Modulo 3
Modulo 4
Modulo 5
Lunghezza del Bus
Ld= Lunghezza derivazione
Ld
For maximum performance, it is recommended to use special shielded cables, designed specically for data
communication.

MI00582-0-EN INSTALLATION MANUAL 5/6
SETTING THE DIP-SWITCHES
RS232/RS485 SETTING: RS232 or RS485 conguration on terminals 10-11-12 (serial port 2)
SW2
1 ON RS232 ACTIVATION
0 OFF RS485 ACTIVATION
KEY
1 ON
0 OFF
SW1 DIP-SWITCH:
Through DIP-SWITCH-SW1 it is possible to set the IP conguration of the device:
DESCRIPTION DIP 1 DIP 2
To obtain the conguration from the Flash memory, both SW1
DIP switch selectors must be set to OFF
To reset the device to factory settings both SW1 DIP switches
must be set to ON
To force the device’s IP address to the standard value of
SENECA Ethernet products: 192.168.90.101
Reserved
The DIP-switch settings are read only at boot time. At each change, perform a restart.
WARNING
USB PORT (Z-4DI-2AI-2DO)
CU MICROO TG-A-- CU MICROB-A-
CU MICROB-A-
Configurazione
tramite APP
Android
Configurazione
tramite
software PC
The module is designed to exchange data according to the modes dened by the MODBUS protocol. It has a micro USB
connector on the front panel and can be congured using applications and/or software programs.
The USB serial port uses the following communication parameters: 115200,8,N,1.
The USB communication port responds exactly like the serial ports, with the exception of the communication parameters. For
more information, visit the site shown on page 1.
Check that the device in question is included in the list of products supported by the Easy Setup APP in the store.
CONNECTOR IDC10
Power supply and Modbus interface are available using the Seneca DIN rail bus, via the IDC10 rear connector, or the
Z-PC-DINAL-17.5 accessory.
RS485GND
RS485A
RS485B
Power Supply AC / +
Power Supply AC / -
IDC 10
1
Back connector (IDC 10)
The illustration shows the meanings of the various
IDC10 connector pins if signals are to be sent via
them directly.
Android APP
conguration
PC software con-
guration

MI00582-0-EN INSTALLATION MANUAL 6/6
ELECTRICAL CONNECTIONS
10 GND
11 A(+)
12 B (-)
10 GND
11 RX
12 TX
N.A.2=22
CO.2=23
N.C.2=24
N.A.1=19
CO.1=20
N.C.1=21
13 DI1
14 DI2
15 +12V
16 GND
17 DI3
18 DI4
0V
Max 24V
12V 20mA
13 DI1
14 DI2
15 +12V
16 GND
17 DI3
18 DI4
13 DI1
14 DI2
15 +12V
16 GND
17 DI3
18 DI4
0V
2
1
3
5A I1
6A I2
1 12V
4GND
5AI1
6AI2
+
+
+
+
Attention: the upper power supply limits must not be exceeded, as this might cause serious damage to the module.
To meet the electromagnetic immunity requirements:
- use shielded signal cables;
- connect the shield to a preferential instrumentation earth system;
- separate shielded cables from other cables used for power installations (transformers, inverters, motors, induction
ovens, etc.).
POWER SUPPLY
The power supply is connected to terminals 2 and 3.
The supply voltage must be between:
11 and 40Vdc (indifferent polarity), or between 19 and 28 Vac.
The power supply source must be protected from any failures in the module by means of
a suitably sized fuse.
Power supply
Power supply
Auxiliary voltage
+12Vdc at 30mA
ANALOGUE INPUTS
DIGITAL INPUTS (ONLY ZE-4DI-2AI-2DO and Z-4DI-2AI-2DO)
NPN INPUT PNP INPUT WITH EXTERNAL POWER
DIGITAL OUTPUTS (ONLY ZE-4DI-2AI-2DO and Z4DI-2AI-2DO)
COM2 SERIAL PORT
4GND
5AI1
6AI2
Voltage Active sensor current (4 wires) Passive sensor current (2 wires) The module has two
analogue inputs that can be
congured via software as
voltage or current.
For the conguration
software, see the user
manual
SERIAL
PORT
RS485
(SW2=OFF)
SERIAL
PORT
RS232
(SW2= ON)
The has two digital outputs with free
contacts.
The two gures show the internal relay
contacts available.
The module has a COM2 serial port
congurable via the SW2 switch on
terminals 10-11-12.