WAGO I/O-SYSTEM 750 User manual

Public
Pos: 2/ D oku me ntati on allg em ein /Ei nb and /Ei nb and Fro nts eite -H andb uch; CI 20 17; mit Do cVaria blen (St andar d) @ 28\mod_1486477502910_0.docx@ 405388@ @ 1
Manual
WAGO I/O System 750
750-1505
16DO 24VDC 0.5 A, low
-side switching
16
-Channel Digital Output Module 24 VDC;
Low
-side switching
Version 1.1.0
Pos: 3/ A ll e S er ie n ( All g em ei ne M od ul e) /Rec htl ic h es, Allg e mei n es/ I mpr e ssu m für St a nd ard h an d büc h er - al lg . A ng a be n, Ansc hr i ft en, Telef onn u m mer n und E-M ail-A dr es s e n @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1

2 WAGO I/O System 750
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
© 2021 WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: www.wago.com
Technical Support
Phone: [phone] – 4 45 55
Fax: [phone] – 84 45 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [e-mail]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.
=== Ende d er List e f ür T e xt mar ke Ei nb a nd_ v orn e == =

WAGO I/O System 750 Table of Contents 3
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Pos: 5/ D ok ume nt ati on allg em ein /V erz eic h nis se /I nhal ts ver z eic hni s - Ü b ers chri f t oG und V erz ei ch nis @ 3\mod_1219151230875_21.docx@21063 @ @ 1
Table of Contents
1Notes about this Documentation .............................................................5
1.1 Validity of this Documentation.................................................................5
1.2 Copyright................................................................................................5
1.3 Symbols .................................................................................................6
1.4 Number Notation ....................................................................................8
1.5 Font Conventions ...................................................................................8
2Important Notes ........................................................................................9
2.1 Legal Bases............................................................................................9
2.1.1 Subject to Changes............................................................................9
2.1.2 Personnel Qualifications ....................................................................9
2.1.3 Use of the 750 Series in Compliance with Underlying Provisions.......9
2.1.4 Technical Condition of Specified Devices.........................................10
2.1.4.1 Disposal ......................................................................................10
2.1.4.1.1 Electrical and Electronic Equipment........................................10
2.1.4.1.2 Packaging...............................................................................11
2.2 Safety Advice (Precautions) .................................................................12
3Device Description..................................................................................15
3.1 View .....................................................................................................17
3.2 Connectors...........................................................................................18
3.2.1 Data Contacts/Local Bus..................................................................18
3.2.2 Power Jumper Contacts/Field Supply ..............................................19
3.2.3 Push-in CAGE CLAMP®Connectors................................................21
3.3 Display Elements..................................................................................22
3.4Operating Elements..............................................................................22
3.5 Schematic Diagram ..............................................................................23
3.6 Technical Data .....................................................................................24
3.6.1 Device..............................................................................................24
3.6.2 Communication................................................................................24
3.6.3 Supply..............................................................................................24
3.6.4 Outputs ............................................................................................24
3.6.5 Connection Type..............................................................................25
3.6.6 Climatic Environmental Conditions...................................................25
3.7 Approvals .............................................................................................26
3.8 Standards and Guidelines ....................................................................27
4Process Image.........................................................................................28
5Mounting..................................................................................................29
5.1 Mounting Sequence..............................................................................30
5.2 Inserting and Removing Devices ..........................................................31
5.2.1 Inserting the I/O Module...................................................................31
5.2.2 Removing the I/O Module ................................................................32
6Connect Devices .....................................................................................33
6.1 Connecting a Conductor to the Push-in CAGE CLAMP®......................33

4 Table of Contents WAGO I/O System 750
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
7Using in Safety Related Applications ....................................................34
7.1 Important Notes....................................................................................35
7.2 Connecting the I/O Module to Safety Switching Devices or
F I/O Modules.......................................................................................36
7.2.1 General Structure of a Potential Group ............................................36
7.2.2 Examples of Connection ..................................................................37
8Use in Hazardous Environments ...........................................................38
8.1 Marking Configuration Examples ..........................................................39
8.1.1 Marking for Europe According to ATEX and IECEx..........................39
8.1.2 Marking for the United States of America (NEC) and Canada
(CEC)...............................................................................................43
8.2 Installation Regulations.........................................................................46
8.2.1 Special Notes including Explosion Protection...................................46
8.2.2 Special Notes Regarding ANSI/ISA Ex ............................................48
List of Figures ..................................................................................................49
List of Tables....................................................................................................50
=== En de der Lis te für T extmar ke Verz eich nis_vor ne == =

WAGO I/O System 750 Notes about this Documentation 5
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Pos: 7/ Al le Seri e n (A llg e mei n e M od ul e) /Üb ers c hri ft en/ Ebe n e 1/H in wei s e z u dies er D o ku ment ati on - Ü ber sc hr ift 1 @ 4\mod_1237987661750_21.docx @ 29029@ 1@ 1
1 Notes about this Documentation
Pos: 8/ All e S eri en (A llg em eine M od ul e)/Si cher h eits- unds onstige Hinweise/Hinweis/Hinweis:D okumentationaufbewahren@ 4\mod_1237987339812_21.docx@ 29026@ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation
is included, if necessary.
Pos: 9/ All e S eri en (A llg em eine M od ul e)/Üb ers c hr ift en/ E be n e 2/ G ülti g kei tsb er eic h - Ü ber sc hr ift 2 @ 1 2\mod_1338912448776_21.docx@ 96469@ 2 @ 1
1.1 Validity of this Documentation
Pos: 10 /S eri e 7 50 ( WA GO I/O S YS TEM )/H i nweis e z ur Do ku ment ati on ( alt e S tru ktur )/ Gül tig kei ts ber eic h/G ülti g kei tsb erei ch D o ku ment ati o n I/ O-Modul750-xxxx, o hne Var iant enang abe @ 14\mod_1358944037947_21.docx @ 109346@ @1
This documentation is only applicable to the I/O module 750-1505
(16DO 24VDC 0.5 A, low-side switching).
Pos: 11 /S eri e 7 50 ( WA GO I/O S YS TEM )/H i nweis e z ur Do ku ment ati on ( alt e S tru ktur )/H i nwei se/ Ac ht ung: Hin wei s z ur D o kum ent atio n I /O-Modul e 750-xxxx @ 4\mod_1237986979656_21.docx @ 29023@ @ 1
The I/O module 750-1505 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus coupler or
controller.
Consider power layout of the WAGO I/O System 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler or controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
Pos: 12.1 / All e Seri en ( All ge mei ne M od ule) /Ü bers chr ift e n/ Ebe ne 2/U r heb er sc hutz -Ü ber sc hri ft 2 @ 23\mod_1435647042188_21.docx @ 184808@ 2@ 1
1.2 Copyright
Pos: 12.2 / All e Seri en ( A llg e mei ne M o dul e)/R ec htl ich es , Al lg e mei nes /U rh eb ers c hutz aus führ li ch @ 4\mod_1235565145234_21.docx@ 27691@ @ 1
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos:12.3/Dokumentationallgemein/Gliederungselemente/---Seit e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

6 Notes about this Documentation WAGO I/O System 750
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Pos: 12.4 / All e Seri en ( All ge mei ne M od ule) /Ü bers chr ift e n/ Ebe ne 2/ S ymbol e - Ü b ers chr if t 2@ 13\mod_1351068042408_21.docx@ 105270@ 2 @ 1
1.3 Symbols
Pos: 12 .5.1 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti g e H i n weis e/ Ge fa hr/ G ef ahr : _War nu ng vor P ers on ens ch ä de n al lg e mei n _ - Er läut er ung @ 13 \mod_1343309450020_21.docx@ 101029@ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12 .5.2 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti ge H i nwei s e/G efa hr /G ef ahr : _ War nu ng vor P ers on en sch ä de n d urc h el e ktri sc he n St ro m_ - Erläuterung @ 13\mod_1343309694914_21.docx@ 101030@ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12 .5.3 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti ge H i nwei s e/W ar nung / War n ung: _W arn u ng vor P er so nens c häd e n al lg emei n_ - Erläuterung@ 13\mod_1343309877041_21.docx@ 101035@ @ 1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 12 .5.4 /Al le Seri en (All gemei ne Mod ul e)/ Si ch er h eits - u nd so ns ti ge H i n weis e/ Vors ic ht /V ors ich t: _War n ung vor Person e nsc hä d en al lg em ein _ - Erläuterung @ 13\mod_1343310028762_21.docx@ 101038@ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 12 .5.5 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti ge H i nwei s e/A c htung / Ach tu ng : _ War nu ng vor Sachsc h äd en al lg em ein _ - Erläuterung@ 13\mod_1343310134623_21.docx @ 101041@ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12 .5.6 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti ge H i nwei s e/A c htung / Ach tu ng : _ War nu ng vor Sachsc h äd en d urc h elek tros tat ische Aufladung_- Er l äut er ung @ 13\mod_1343310227702_21.docx@ 101044@ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12.5 .7 /All e Serien ( Allge meine M odule) /Sic herhei ts- und sonstige Hin weise/Hinweis/Hinweis:_WichtigerHi nweis allgemein_ - Erläuterung@ 13\mod_1343310326906_21.docx@ 101047 @ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 12 .5.8 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti g e H i n weis e/I nf or ma ti o n/I nf or ma ti on: _W eiter e I nf or ma ti on allg e mei n_ -Er l äu ter ung @ 13 \mod_1343310439814_21.docx@ 101051@ @ 1

WAGO I/O System 750 Notes about this Documentation 7
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos:12.6/Dokumentationallgemein/Gliederungselemente/---Seit e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

8 Notes about this Documentation WAGO I/O System 750
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Pos: 12.7 / All e Seri en ( All ge mei ne M od ule) /Ü bers chr ift e n/ Ebe ne 2/D ar st ell ung der Z a hle ns yst em e - Ü bers c hri ft 2 @ 23\mod_1435647128078_21.docx @ 184811@ 2@ 1
1.4 Number Notation
Pos: 12.8 / All e Seri en ( All ge mei ne M od ule) /R ec htli ch es, Al lg e mei nes / Za hle ns yst e me @ 3\mod_1221059454015_21.docx @ 21711 @ @ 1
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated
with dots (.)
Pos: 12.9 / All e Seri en ( All ge mei ne M od ule) /Ü bers chr ift e n/ Ebe ne 2/ Sc hri ft ko nvent i one n - Ü ber sc hri ft 2 @ 23\mod_1435647186005_21.docx @ 184814@ 2@ 1
1.5 Font Conventions
Pos: 12.1 0 / Al le Ser ie n (Al l ge m ein e M o dul e)/ Re ch tl ic h es, Allg e mei n es/ Sc hr if t kon ve nti on en @ 3\mod_1221059521437_21.docx @ 21714@ @ 1
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.:
Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.:
[F5]
Pos: 13 /D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

WAGO I/O System 750 Important Notes 9
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Pos: 14 /Al l e S eri en ( All ge mei ne M od ule) /Ü b ersc hrif te n/ Ebe ne 1/ Wic hti ge Erl äu ter unge n - Ü ber sc hr ift 1 @ 4 \mod_1241428899156_21.docx@32170 @ 1 @ 1
2 Important Notes
Pos: 15.1 / All e Seri en ( All ge mei ne M od ule) /R ec htli ch es, Al lg em ei nes /Wi chti g e Er l äuter ung en - Einl eit u ng @ 3\mod_1221059818031_21.docx@ 21717@ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 15 .2 /All e Seri en( Allg emeine M odul e)/Ü berschr ifte n/Ebe ne 2/Rec htlic he Gr undlag en - Über sc hr ift 2 @ 3\mod_1221060626343_21.docx@ 21726@ 2 @ 1
2.1 Legal Bases
Pos: 15.3 / All e Seri en ( A llg e mei ne M o dul e)/R ec htl ich es , Al lg e mei nes /Ä nd er ung s vor beh alt - Üb ersc hrift 3 un d Inhal t @ 3\mod_1221060036484_21.docx@ 21720 @ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all
rights arising from the granting of patents or from the legal protection of utility
patents. Third-party products are always mentioned without any reference to
patent rights. Thus, the existence of such rights cannot be excluded.
Pos: 15.4 /S erie 750 (WA GO I/O SYSTEM) /Wichti g e Er l äut er u ng e n ( al te Str ukt ur )/P er s on al qu al ifi kat io n/ Per s on alq u ali fi kati o n 7 50- xxxx - Ü bersc hrift 3 u nd Inhal t @ 3\mod_1224061208046_21.docx@ 24063@ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on WAGO I/O System 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos:15.5/Serie750(WAGO I/OSYSTEM)/WichtigeErläuterungen(alteStruktur)/Bestimmungsgemäße Verwendung/BestimmungsgemäßeVerwendung 750-xxxx - Ü b ersc hr if t 3 @ 32\mod_1536041141528_21.docx@ 498494@ 3 @ 1
2.1.3 Use of the 750 Series in Compliance with Underlying
Provisions
Pos:15.6/Serie750(WAGO I/OSYSTEM)/WichtigeErläuterungen(alteStruktur)/Bestimmungsgemäße Verwendung/BestimmungsgemäßeVerwendung 750-xxxx für Ger ät e, STD mit EN 61 000-6-3 -Ver wei s auf G er ä te-H B @ 3\mod_1224064151234_21.docx@ 24070 @ @ 1
Fieldbus couplers, controllers and I/O modules found in the modular WAGO I/O
System 750 receive digital and analog signals from sensors and transmit them to
actuators or higher-level control systems. Using controllers, the signals can also
be (pre-) processed.
The devices have been developed for use in an environment that fulfills the
requirements of protection type IP20 and are designed for use in dry interior
spaces. Protection against finger injury and solid impurities up to 12.5 mm
diameter is assured; protection against water damage is not ensured. Unless
otherwise specified, operation of the devices in wet and dusty environments is
prohibited.
Use without additional protective measures in environments within which dust,
corrosive fumes, gases or ionized radiation can occur is considered improper
use.
Operating the WAGO I/O System 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information in

10 Important Notes WAGO I/O System 750
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
the section “Device Description” > “Standards and Guidelines” in the manual for
the used device.
Appropriate housing (per 2014/34/EU) is required when operating the WAGO I/O
System 750 in hazardous environments. Please observe the installation
regulations! Please note that a prototype test certificate must be obtained that
confirms the correct installation of the system in a housing or switch cabinet.
The implementation of safety functions such as EMERGENCY STOP or safety
door monitoring must only be performed by the F I/O modules within the modular
WAGO I/O System 750. Only these safe F I/O modules ensure functional safety
in accordance with the latest international standards. WAGO's interference-free
output modules can be controlled by the safety function.
Pos: 15.7 / All e Seri en ( All ge mei ne M od ul e)/R ec ht lic hes , A llg e mei nes /T ec hni sc her Z us t and der Gerät e - Ü bersc hrift 3 u nd Inhal t @ 3\mod_1221060446109_21.docx@ 21723@ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. These
modules contain no parts that can be serviced or repaired by the user. The
following actions will result in the exclusion of liability on the part of WAGO
Kontakttechnik GmbH & Co. KG:
• Repairs,
• Changes to the hardware or software that are not described in the
operating instructions,
• Improper use of the components.
Further details are given in the contractual agreements. Please send your
request for modified and new hardware or software configurations directly to
WAGO Kontakttechnik GmbH & Co. KG.
Pos:15.8/Dokumentationallgemein/Gliederungselemente/----Leer zeil e-( 1Z)---- @ 28\mod_1485262995837_0.docx@ 404006@ @ 1
Pos: 15 .9 /All e Seri en ( Al lg e mei ne Mod ule) /Ü ber s c hri ft e n/ Eb e ne 4/ E nts or g en -Ü b ersc hr if t 4 @ 30 \mod_1510145115652_21.docx@469859@ 4 @ 1
2.1.4.1 Disposal
Pos: 15.1 0. 1 / Al le Ser ie n (Al l ge m ein e M o dul e)/ Üb er sc hr if t en/ Ebe n e 5/Ele kt ro- un d Elekt ro ni kg er ät e - Ü ber sc hr ift 5 @ 32\mod_1537446988068_21.docx@501657@ 5 @ 1
2.1.4.1.1 Electrical and Electronic Equipment
Pos:15.10.2/Alle Serien(AllgemeineModule)/Rechtliches,Allgemeines/Elektro- und El e ktro ni kger ät e @ 32\mod_1532425086061_21.docx @ 491989@ @1
Electrical and electronic equipment may not be disposed of
with household waste. This also applies to products without
this symbol.
Electrical and electronic equipment contain materials and substances that can be
harmful to the environment and health. Electrical and electronic equipment must
be disposed of properly after use.
WEEE 2012/19/EU applies throughout Europe. Directives and laws may vary
nationally.

WAGO I/O System 750 Important Notes 11
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Environmentally friendly disposal benefits health and protects
the environment from harmful substances in electrical and
electronic equipment.
• Observe national and local regulations for the disposal of electrical and
electronic equipment.
• Clear any data stored on the electrical and electronic equipment.
• Remove any added battery or memory card in the electrical and
electronic equipment.
• Have the electrical and electronic equipment sent to your local
collection point.
Improper disposal of electrical and electronic equipment can be harmful to the
environment and human health.
Pos: 15.1 0.3 /D o ku ment ati on allge m ein /Gli ed er ung s el e ment e/ ----Leer z eil e-(1Z)---- @ 2 8\mod_1485262995837_0.docx @ 404006 @ @ 1
Pos: 15.1 0. 4 / Al le Ser ie n (Al l ge m ein e M o dul e)/ Üb er sc hr if t en/ Ebe n e 5/Ver pac k u ng - Ü ber sc hr ift 5 @ 32\mod_1537447044202_21.docx@501662@ 5 @ 1
2.1.4.1.2 Packaging
Pos: 15.1 0. 5 / Alle Serien(AllgemeineModule)/Rechtliches,Allgemeines/Verpackung@ 32\mod_1537446786416_21.docx@ 501653@ @ 1
Packaging contains materials that can be reused.
PPWD 94/62/EU and 2004/12/EU packaging guidelines apply throughout
Europe. Directives and laws may vary nationally.
Environmentally friendly disposal of the packaging protects the environment and
allows sustainable and efficient use of resources.
• Observe national and local regulations for the disposal of packaging.
• Dispose of packaging of all types that allows a high level of recovery,
reuse and recycling.
Improper disposal of packaging can be harmful to the environment and wastes
valuable resources.
Pos: 15.1 1 /D o kum ent ati on al lg em ei n/Gli ed eru ng sel eme nt e/---Sei t enw ec hs el--- @ 3 \mod_1221108045078_0.docx @ 21810@ @ 1

12 Important Notes WAGO I/O System 750
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Pos: 15.1 2 / All e S er ie n ( All ge m ein e M o dul e) /Üb er sc hr ift en /E ben e 2/Sich er hei ts hin w eis e - Ü ber s chri ft 2 @ 6\mod_1260180299987_21.docx@ 46724@ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 15.1 3 /Al le S eri en ( Allg em ein e Mo dul e) /Sic h er hei ts- un d sonsti ge Hin weis e/Einl eitu ng Sich erheit shin weise Har dwar e @ 6\mod_1260180170493_21.docx @ 46720 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 15.1 4.1 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o ns tig e Hin wei se /G ef a hr /G ef ahr: Nic ht an G erät e n unter Spa nnu ng arbei te n! @ 6\mod_1260180365327_21.docx@ 46727@ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 15.1 4.2 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o ns tig e Hin wei se /G ef a hr /G ef ahr: Pr odu kt nur i n eine m g e ei gn et en Geh äus e ei nb a uen! @ 3 3\mod_1543581881435_21.docx@ 511972@ @ 1
Install device in only one suitable enclosure!
The device is an open system. Install the device in a suitable enclosure. This
enclosure must:
• Guarantee that the max. permissible degree of pollution is not exceeded.
• Offer adequate protection against contact.
• Prevent fire from spreading outside of the enclosure.
• Offer adequate protection against UV irradiation.
• Guarantee mechanical stability
• Restrict access to authorized personnel and may only be opened with tools
Pos: 15.1 4.3 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- undsonstigeHinweise/Gefahr/Gefahr:Trennvorrichtung undÜberstromschutz@ 33\mod_1543915978439_21.docx @ 512267 @ @ 1
Ensure disconnect and overcurrent protection!
The device is intended for installation in automation technology systems.
Disconnect protection is not integrated. Connected systems must be protected by
a fuse.
Provide suitable disconnect and overcurrent protection on the system side!
Pos: 15.1 4.4 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o ns tig e Hin wei se /G ef a hr /G ef ahr: Unf all ver h üt ungs vor sc hr if t en b e ach te n! @ 6\mod_1260180657000_21.docx@ 46735@ @ 1
Pos: 15.1 4.5 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o ns tig e Hin wei se /G ef a hr /G ef ahr: Auf nor mg erec ht e n A nsc hl uss ac ht en! @ 6\mod_1260180753479_21.docx @ 46739@ @ 1
Ensure a standard connection!
To minimize any hazardous situations resulting in personal injury or to avoid
failures in your system, the data and power supply lines shall be installed
according to standards, with careful attention given to ensuring the correct
terminal assignment. Always adhere to the EMC directives applicable to your
application.
Pos: 15.1 5. 1 / S er ie 750 ( W AG O I /O SYST EM )/ Wi ch ti g e Er l äut er ung en ( al t e St ru kt ur ) /Sic her hei t s- u n d s on sti g e H i n weis e/ A c ht ung / Ac ht ung : E i n wan dfr ei e Kont a kti eru ng zur T rag s c hie n e g ew ähr l eis t en! @ 3 4\mod_1550481407638_21.docx@ 530599@ @ 1

WAGO I/O System 750 Important Notes 13
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Ensure proper contact with the DIN-rail!
Proper electrical contact between the DIN-rail and device is necessary to
maintain the EMC characteristics and function of the device.
Pos: 15.1 5.2 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o ns tig e Hin wei se /A cht u ng /Ac ht u ng : D ef e kt e od er bes ch ädig t e Gerät e austa usc h en! @ 6\mod_1260180857358_21.docx @ 46743@ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts).
Pos: 15.1 5.3 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- undsonstigeHi n wei se /A cht u ng /Ac ht u ng : G er ät e vor krieche n de n und is oli er end en Sto ff en s c hüt ze n! @ 6\mod_1260181036216_21.docx@ 46747@ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for
handling devices/modules.
Pos: 15.1 5.4 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o ns tig e Hin wei se /A cht u ng /Ac ht u ng : R ei ni gu ng nur mit zul äss ig e n M at er ial ie n! @ 6\mod_1260181203293_21.docx@ 46751@ @ 1
Clean only with permitted materials!
Clean housing and soiled contacts with propanol.
Pos: 15.1 5.5 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- undsonstigeHinweise/Achtung/Achtung:KeinKontaktsprayv erwend en! @ 6\mod_1260181290808_21.docx@ 46755@ @ 1
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 15.1 5.6 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- und s ons ti g e H in w ei se /A cht ung / Ac ht u ng : V er pol ung en d er Date n- un d Vers org u ng sl ei t u ngen ver m eid e n! @ 6\mod_1260184045744_21.docx@ 46767 @ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 15.1 5.7 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o ns tig e Hin wei se /A cht u ng /Ac ht u ng : El e ktr ost ati sc h e Entla du ng verm ei de n! - DIN EN 61340-5-1/ -3 @ 6\mod_1260181364729_21.docx@ 46759@ @ 1

14 Important Notes WAGO I/O System 750
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos: 16 /D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

WAGO I/O System 750 Device Description 15
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Pos: 17 /A ll e Seri en (Allg e mei n e M od ul e)/ Ü b ers chr if te n/ Eb e ne 1/G erät e bes c hr ei bung - Üb er schr i f t 1@ 3\mod_1233756084656_21.docx@ 27096 @ 1@ 1
3 Device Description
Pos: 18.1 / S eri e 750 ( WA G O I/O S YS TEM ) / Ger ät eb esc hr ei bu ng (al te Stru kt ur )/ Ei nl eit ung / A nwe n du ng /D O /A n wen d ung 750-x5 xx D O @ 3\mod_1233764594468_21.docx@ 27120@ @ 1
The 750-1505 (16DO 24VDC 0.5 A, low-side switching) Digital Output Module
transmits binary control signals from the automation device to the connected
actuators (e.g., solenoid valves, contactors, transmitters, relays or other electrical
loads).
Pos: 18.2 / S eri e 7 5 0 (W A GO I/O S YS T EM) / Ger ät eb esc hr ei bu ng (alt e St r u ktur ) /Ei nl eit u ng /I/ O -Bes c hr ei bu ng /DO / I/ O-B esc hrei bu ng 7 5 0-1 50 x 16 D O 1-LeiterCA GECL AMP@ 3 \mod_1233764626734_21.docx@ 27124 @ @1
The I/O module has 16 output channels, providing a direct connection to single-
wire actuators.
The actuators are connected to the CAGE CLAMP®connections DO 1 ... DO 16.
Pos:18.3/Serie750( W A GO I/O S YS T EM )/ Ger ät eb esc hr ei bu ng (al te Stru kt ur) /Ei nlei t u ng/ I/ O-B esc hrei bu ng /Al lg e m ein /V er weis auf Kapi tel "A nsc hlüs s e" @ 8\mod_1276775378035_21.docx@ 57956@ @ 1
The assignment of the connections is described in the “Connectors” section.
Pos: 18.4 /Dokumentation allgemein/Gliederungselemente/---Leera bs atz-(2 Z)--- @ 3\mod_1224662755687_0.docx@ 24460 @ @ 1
Pos: 18.5 / S eri e 750 ( WA G O I/O S YS TEM ) / Wic htig e Erlä ut er u ng en ( al t e St r u kt ur )/S ic h er h ei ts- und sonstige Hinweise/Hinweis/Hinweis:DO Potentialver vi elfäl ti gung s mod ul e f ür A kt orv ers org ung ein set zen @ 3\mod_1233765481250_21.docx@ 27140@ @ 1
Use field side connection modules!
Where required, use the appropriate field side connection modules for power
supply to the actuators.
Pos: 18.6 / S eri e 750 ( WA G O I/O S YS TEM ) / Wic htig e Erlä ut er u ng en ( al t e St r u kt ur )/S ic h er h ei ts- und sonstige Hinweise/Achtung/Achtung:DO InduktionsspannungsbegrenzungElektronik @ 3\mod_1233815757507_21.docx @ 27153@ @ 1
Limit all induced voltage!
The electronic components of the I/O module can be damaged by the induced
voltage produced when inductive loads are de-activated.
An appropriate protection circuit, e.g., a recovery diode, must be installed in
parallel to the load to limit this induced voltage.
Pos: 18.7/Serie750(WAGO I/OSYSTEM)/WichtigeErläuterungen(alteStruktur)/Sicherheits- undsonstigeHinweise/Achtung/Achtung:DO Überlastschutz- EinpeiseklemmemitSicherung@ 3\mod_1233814881117_21.docx@ 27150 @ @ 1
Provide for overload protection!
Overloading can damage the electronic components of the I/O module.
A fused supply module (750-601) must be installed upstream of the I/O module
to protect it against overloading!
Pos: 18.8 / S eri e 750 ( WA G O I/O S YS TEM ) / Ger ät eb esc hr ei bu ng (al te Stru kt ur )/ Ei nl eit u ng /I/ O-B es c hrei bu ng /DO / I/ O-B esc hrei bu ng 7 5 0-x5 xxD O LSS / neg ativsc halten d( 0 V) @ 3\mod_1233817190023_21.docx@ 27163@ @ 1
The I/O module outputs provide negative switching. If the signal status of an
output channel is at "high" the 0V potential for field power will be switched to the
appropriate output connection.
Pos: 18.9 / S eri e 750 ( WA G O I/O S YS TEM ) / Ger ät eb esc hr ei bu ng (al te Stru kt ur )/ Ei nl eit ung / LE D-A nz eig e/ LED Zus ta nd Signal @ 3\mod_1233755258578_21.docx@ 27087@ @ 1
A green LED indicates the switched status of each channel.
Pos: 18.1 0 / S er ie 750 ( W AG O I /O SYST EM )/ G erä te be sc hr ei bu ng (alt e Struk t ur) /Ei nl ei t ung/ LE D-An zei g e /V er weis auf Kapi tel " A nzei g e el em e nt e" @ 5\mod_1246010525000_21.docx@ 36194 @ @ 1
The meaning of the LEDs is described in the “Display Elements” section.
Pos: 18.1 1 / S er ie 750 ( W AG O I /O SYST EM )/ G erä te be sc hr ei bu ng (alt e Struk t ur) /Ei nl ei t ung/ V ers or g u ng/ V ers org ung 24 V , 0 V ü b er L eis t u ngs kont a kt e St an d ar d @ 3\mod_1226498974531_21.docx@ 25020@ @ 1
The I/O module 750-1505 (16DO 24VDC 0.5 A, low-side switching) receives the
24 V voltage supply for the field level from an upstream I/O module or from the
fieldbus coupler/controller via blade-formed power jumper contacts. It then
provides these potentials to subsequent I/O modules via spring-formed power
jumper contacts.
Pos: 18.1 2 / S er ie 750 ( W AG O I /O SYST EM )/ Wi ch ti g e Er l äut er ung en ( al t e St ru kt ur ) /Sic her hei ts- u n d s on sti g e H i n w eis e/ Ac ht ung / Ac ht ung : Maxi m aler Str o m Lei s tu ng s kont a kt e 1 0 A@ 3\mod_1226499143500_21.docx @ 25029@ @ 1

16 Device Description WAGO I/O System 750
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Do not exceed maximum values via power contacts!
The maximum current that can flow through the power jumper contacts is 10 A.
The power jumper contacts can be damaged and the permissible operating
temperature can be exceeded by higher current values.
When configuring the system, do not exceed the permissible maximum current
value. If there is a higher power requirement, you must use an additional supply
module to provide the field voltage.
Pos: 18.1 3 / S er ie 750 ( W AG O I /O SYST EM )/ Wi ch ti g e Er l äut er ung en ( al t e St ru kt ur ) /Sic her hei ts- u n d s ons tig e Hi n wei se/ Hi nw eis/H in wei s: P ot ent ial ein sp eise m odul für Erde einse tze n! (kei ne LK für Erde) @ 3\mod_1226499037468_21.docx@ 25023 @ @ 1
Use supply modules for ground (earth)!
The I/O module has no power jumper contacts for receiving and transmitting the
earth potential. Use a supply module when an earth potential is needed for the
subsequent I/O modules.
Pos: 18.1 4 / S er ie 750 ( W AG O I /O SYST EM )/ G erä te be sc hr ei bu ng (alt e Struk t ur) /Ei nl ei t ung/ V ers or g u ng/ G al vani sc h e T re n nu ng F eld/ S ys t e m @ 3\mod_1233756478750_21.docx @ 27102@ @ 1
The field voltage and the system voltage are electrically isolated from each other.
Pos: 18.1 5 / S er ie 750 ( W AG O I /O SYST EM )/ G erä te be sc hr ei bu ng (alt e Struk t ur) /Ei nl ei t ung/ V ers or g u ng/ A nor d nu ng u nt er Ber üc ksi c htigung der Leistungskontaktebeliebig@ 3\mod_1233756233468_21.docx @ 27099@ @ 1
With consideration of the power jumper contacts, the individual modules can be
arranged in any combination when configuring the fieldbus node.
An arrangement in groups within the group of potentials is not necessary.
Pos: 18.1 6 / S er ie 750 ( W AG O I /O SYST EM )/ G erä te be sc hr ei bu ng (alt e Struk t ur) /Ei nl ei t ung/ E ins at z ber ei c h/ Ei ns at zb er eic h 750-xxx x al le Koppl er/C o ntr oll er o h ne Ei ns c hrä nkung @ 3 \mod_1232541691906_21.docx@ 26522 @ @ 1
The I/O module 750-1505 can be used with all fieldbus couplers/controllers of the
WAGO-I/O-SYSTEM 750.
Pos: 19 /D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

WAGO I/O System 750 Device Description 17
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Pos: 20 /Al l e S eri en ( All ge mei ne M od ule) /Ü b ersc hrif te n/ Ebe ne 2/ A nsic ht - Ü b ers chri ft 2 @ 4\mod_1240984217343_21.docx @ 31958@ 2 @ 1
3.1 View
Pos: 21 / S eri e 750 ( WA G O I /O SYS TEM ) / Ger ät ebes c hr ei bu ng (al te Stru kt ur )/A ns i c ht/D O/ An si ch t 750-1 50x 16 DO C AG E C L AMP - A bb . @ 3\mod_1224766395937_21.docx @ 24653@ @ 1
Figure 1: View
Pos: 22 / S eri e 750 ( WA G O I /O SYS TEM ) / Ger ät ebes c hr ei bu ng (al te Stru kt ur )/A ns i c ht/ A ns ic ht Push-in CageClamp®_LegendemitLEDs @ 15\mod_1370852562803_21.docx@ 122213@ @ 1
Table 3: Legend for Figure “View”
Pos.
Description
Details See Section
1
Marking possibility with Mini-
WSB
---
2
Status LEDs
“Device Description” > “Display Elements”
3
Data contacts
“Device Description” > “Connectors”
4
Push-in CAGE CLAMP®
connectors
“Device Description” > “Connectors”
5
Power jumper contacts
“Device Description” > “Connectors”
6
Release tab
“Mounting” > “Inserting and Removing
Devices”
Pos: 23 /D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

18 Device Description WAGO I/O System 750
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Pos: 24 /Al l e S eri en ( All ge mei ne M od ule) /Ü b ersc hrif te n/ Ebe ne 2/ A nsc hlüs se - Ü ber sc hr ift 2 @ 4\mod_1240984262656_21.docx @31961 @ 2@ 1
3.2 Connectors
Pos:25/Serie750 (WAGOI/O SYSTEM)/Gerätebeschreibung(alte Struktur)/Anschlüsse/Datenkontakte/Lokalbus- Übers c hri ft 3 @ 6\mod_1256294684083_21.docx@ 43660 @ 3 @ 1
3.2.1 Data Contacts/Local Bus
Pos: 26.1 / S eri e 750 ( WA G O I/O S YS TEM ) / Ger ät eb esc hr ei bu ng (al te Stru kt ur )/ A nsc hl ü ss e /Da te n k on ta kte - Fel dbus k op pler /-c ontrol ler u nd Modul e – Abbild u ng und B es c hr ei b ung @ 3\mod_1231771259187_21.docx@ 26002 @ @ 1
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the local bus. The
contacting for the local bus consists of 6 data contacts, which are available as
self-cleaning gold spring contacts.
Figure 2: Data Contacts
Pos: 26.2 / S eri e 750 ( WA G O I/O S YS TEM ) / Wic htig e Erlä ut er u ng en ( al t e St r u ktur ) /Si c h erh ei ts- und sonstige Hinweise/Achtung/Achtung:I/O-Mo dule nic ht auf Gol dfeder konta kte leg en! @ 7\mod_1266318463636_21.docx@ 50695@ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos: 26.3 / S eri e 750 ( WA G O I/O S YS TEM ) / Wic htig e Erlä ut er u ng en ( al t e St r u kt ur )/S ic h er h ei ts- und sonstige Hinweise/Achtung/Achtung: ESD- Auf Pote nti ala usg l ei c h der U mg e bu ng a c ht e n! @ 32 \mod_1539077262331_21.docx@504433@ @ 1
Pay attention to potential equalization from the environment!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, please ensure that
environmental factors (personnel, work space and packaging) are properly
equalized. Do not touch any conducting parts, e.g., data contacts.
Pos: 27 /D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

WAGO I/O System 750 Device Description 19
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Pos: 28 /S er i e 7 5 0 ( WA GO I/O S YS TEM ) / Ger ät eb es c hrei bu ng ( al t e Str u ktur ) /A nsc hl ü sse /L ei st u ng s kont a kt e/F el d ver s org ung - Über sc hr ift 3 @ 6 \mod_1256294692864_21.docx@43664 @ 3@ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos: 29.1 /S erie 750 (WA GO I/O SYSTE M) / Wic ht ig e Erlä ut eru ng e n ( al t e Str u ktur ) /Si c h erh ei ts- un d s ons tig e Hinw eis e/ Vor si c ht/ Vors ic ht : Verle tz ungs ge fa hr durc h sc h ar f kan tig e M es s er kont a kte! @ 6\mod_1256193279401_21.docx@ 43414@ @1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury. Do not touch the blade contacts.
Pos: 29.2 / S eri e 7 5 0 (W A GO I/O S YS T EM) / Ger ät eb esc hr ei bu ng (alt e St r u ktur ) /A nsc hl ü sse /L ei st u ng s kont a kt e 2 LK ( M ess er /F ed er ) - Ei nl eitu ng @ 15\mod_1371721641099_21.docx @ 123714 @ @ 1
The I/O module 750-1505 has 2 self-cleaning power jumper contacts that supply
and transmit power for the field side. The contacts on the left side of the I/O
module are designed as blade contacts and those on the right side as spring
contacts.
Pos: 29.3 / S eri e 7 5 0 (W A GO I/O S YS T EM) / Ger ät eb esc hr ei bu ng (alt e St r u ktur ) /A nsc hl ü sse /L ei st u ng s kont a kt e 2 LK ( M ess er /F ed er ) - Ab bil dung (16-Kanal)@ 15\mod_1370866610582_21.docx @ 122222@ @1
Figure 3: Power Jumper Contacts
Pos: 29.4 / S eri e 7 5 0 (W A GO I/O S YS T EM) / Ger ät eb esc hr ei bu ng (alt e St r u ktur ) /A nsc hl ü sse /L ei st u ng s kont a kt e 2 LK ( M ess er /F ed er ) - Leg en de @ 15\mod_1371721352500_21.docx@ 123710@ @1
Table 4: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1
Spring contact
Potential transmission (Uv) for field supply
2
Spring contact
Potential transmission (0 V) for field supply
3
Blade contact
Potential feed-in (0 V) for field supply
4
Blade contact
Potential feed-in (U
v
) for field supply
Pos: 29.5 / S eri e 750 ( WA G O I/O S YS TEM ) / Wic htig e Erlä ut er u ng en ( al t e St r u kt ur )/S ic h er h ei ts- und sonstige Hinweise/Achtung/Achtung:M aximalerStrom Leistungskontakte10 A @ 3\mod_1226499143500_21.docx @ 25 029 @ @ 1
Do not exceed maximum values via power contacts!
The maximum current that can flow through the power jumper contacts is 10 A.
The power jumper contacts can be damaged and the permissible operating
temperature can be exceeded by higher current values.
When configuring the system, do not exceed the permissible maximum current
value. If there is a higher power requirement, you must use an additional supply
module to provide the field voltage.
Pos: 29.6 / S eri e 750 ( WA G O I/O S YS TEM ) / Wic htig e Erlä ut er u ng en ( al t e St r u kt ur )/S ic h er h ei ts- un d s ons tig e Hinw eis e/ Hin w eis/ Hi n wei s: Pote nti alei ns peis e mo dul für Er de eins et z en! ( k ein e LK für Erde) @ 3\mod_1226499037468_21.docx@ 25023@ @ 1

20 Device Description WAGO I/O System 750
750-1505 16DO 24VDC 0.5 A, low-side switching
Manual
Version 1.1.0
Public
Use supply modules for ground (earth)!
The I/O module has no power jumper contacts for receiving and transmitting the
earth potential. Use a supply module when an earth potential is needed for the
subsequent I/O modules.
Pos: 30 /D o kum e nt atio n allg emei n/ Gl ie der ung s elemente/---Seit e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1