Senect SC230-230 User manual

SENECT Power Switch
SC230-230
Manual

Product type
2
Product type
Product name:
SENECT®Power Switch SC230-
230
Type:
PSW-230230-SC
Art.-Nr.:
3101
Producer:
SENECT GmbH & Co. KG
An 44 –Nr. 11
76829 Landau / Germany
Important note:
Please read this manual carefully and store it so that you can use
it later. Read the warning and safety notes attentive.
More information and latest software releases or documents can
be downloaded from:
www.senect.de
Further information, application descriptions and answers to
frequently asked questions can be also found on the SENECT
Forum:
http://forum.senect.de
© Version 1.0 - FW00.90

Table of contents
3
Table of contents
Product type.................................................................................. 2
Table of contents........................................................................... 3
Used symbols and wording ........................................................... 4
General Security Notes.................................................................. 5
Intended use.................................................................................. 7
Getting started .............................................................................. 8
Scope of delivery ....................................................................... 8
Note........................................................................................... 8
Installation and start-up............................................................ 8
Technical data ............................................................................. 11
Information about the correct disposal ...................................... 13
Guarantee.................................................................................... 14

Used symbols and wording
4
Used symbols and wording
DANGER!
Warning of life threatening
dangers.
WARNING!
Warning of possible life
threatening and / or severe
irreversible injuries.
ATTENTION!
Warning of possible medium
or slight injury.
ATTENTION!
Follow the notes to avoid
damage of equipment
NOTE!
Further information for the
use of the device!
ATTENTION!
Warning of electrical shock.

General Security Notes
5
General Security Notes
The SENECT Power Switch SC 230-230 is used to switch
230 V AC consumers via the socket outlets of SENECT control
units.
As this is an electrical product, the usual
requirements, as with all electrical appliances,
must be met. The device may only be operated
with compatible control units or control units
approved by SENECT. The device and all
connected cables must be installed and operated
protected from moisture and wetness. When laying all
cables and lines, care must be taken that no safety-relevant
impairments such as tripping hazards occur. For many
applications, fuse protection by a residual current circuit
breaker with a tripping current < 30 mA is mandatory. Find
out more about this.
The device must be installed protected from overheating by
direct sunlight and must only be operated at an ambient
temperature between 0°C and +40°C. The device must not
be modified, except for extensions or software updates of
SENECT®. It is forbidden to open the device or to penetrate
the inside of the housing in any way.

General Security Notes
6
Use only original SENECT® or SENECT® supplied or approved
extension, replacement, or accessory parts.
The Power Switch is not intended to be used by persons
(including children) with limited physical, sensory or mental
abilities or for lack of experience and/or knowledge, unless
they are supervised or instructed by a person responsible for
their safety on how to operate the device.
Please keep these instructions for use as a reference. Subject
to technical and optical changes as well as printing errors.

Intended use
7
Intended use
The SENECT Power Switch SC 230-230 is used to switch 230
V AC consumers (max. 2000 W) via the socket outlets of
SENECT control units and is intended for use in industrial fish
farming and holding systems. The Power Switch can only be
used in combination with compatible SENECT control units.
Please observe the applicable electrical installation
regulations for the socket supplying the PowerSwitch, such
as the installation of an overcurrent circuit breaker and a
residual current circuit breaker (RCD). Compatible control
units are:
FILTER|CONTROL
FC-A1-333-xxx
AQUACULTURE|CONTROL
AQC-A1-xx3-xx

Getting started
8
Getting started
Scope of delivery
o1 x Power Switch SC230-230
o1 x Manual
Note
Please check directly after delivery, that the
package is not destroyed or damaged or was
opened before. Please check also, that all parts as
listed above are included. If anything is missing or broken,
please contact us as soon as possible within 14 days.
Unfortunately, we cannot accept later information of
damage, which happened during the transport.
Installation and start-up
Install the Power Switch near the control unit and
near an available splash-proof socket (min. IPx4)
designed for the load of the consumer. Ensure that
the installation site is dry and protected from direct sunlight.
Mount the Power Switch by using a screwdriver to open the
two opening flaps (see Fig. 1) on the upper side and screw
the Power Switch into the installation location using two
screws through the now released holes.

Getting started
9
Connect the connection cable with the inscription
"Controller" to your control unit at one of the three 230 V
sockets on the underside.
Connect the Schuko socket to your consumer and plug the
mains plug (label "socket") into the socket.
The Power Switch is now ready for operation and switches
the consumer when the signal is activated at the socket
output of your SENECT controller.

Getting started
10
Quick Start Guide
1. open the fastening flaps.
2. attach the Power Switch.
3. connect the cable ( label " controller ") to the control
unit (switchable 230 V socket on the underside).
4. connect the mains cable socket to the consumer.
5. plug the mains plug (label "socket") into the socket.
The Power Switch is now ready for operation.

Technical data
11
Technical data
Dimensions housing:
125 x 100 x 40 mm
Cable length:
each 1 m
Voltage:
230 V AC
Power consumption:
<< 2 W
Temperature range:
0° to 40 °C
Max. switching power:
2000 W
Ingress protection:
IP44

Technical data
12
Fig. 1: Technical sketch of the Power Switch SC230-230

Information about the correct disposal
13
Information about the correct disposal
Your device is well packed at delivery. Please
dispose the packaging material accordingly to the
regulations in your country.
Do not throw the product in the casual litter bin. Make sure
you are informed about the local disposal regulations and
dispose your product accordingly. Alternatively, you can also
send the product back to the producer.
The SENECT GmbH & Co. KG is member of the Stiftung
Elektro-Altgeräte Register and the products are registered
(WEEE-Reg.-Nr.: DE37193510).

Guarantee
14
Guarantee
Please check at delivery of your device, that all
parts are delivered completely and that they
function correctly. In case of any claims, contact us
immediately per email or phone ([email protected] or +49-
6341 - 95 95 210). Please describe your claim as detailed as
possible so that we can provide a solution as fast as possible.
The product has a guarantee of 1 year and a warranty of 2
years. Furthermore, the § 377 HBG (German law) is valid.