Seura TW-3 User manual

USER MANUAL
WWW.SEURA.COM
FOR SÉURA 42” - 86” OUTDOOR TVs
Tilting Wall Mount
MODEL NUMBER
TW-3

2
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3/8˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket M10 Socket*
2
1
5/16˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5/16˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
The following tools may be required depending on your particular installation. They are not included.
Tools for Installation
Important Safety Information
Prior to the installation of this product, read all instructions. Keep this manual for future reference.
Proper installation procedure by a qualied service technician must be followed as outlined in these installation instructions. Failure to
do so could result in property damage, serious personal injury, or event death.
Safety measures must be practiced at all times during the assembly of this product. Use proper safety equipment and tools for the
assembly procedure to prevent personal injury.
Séura does not warrant against damage caused by the use of any séura product for purposes other than those for which it was designed
or damage caused by unauthorized attachments or modications, and is not responsible for any damages, claims, demands, suits,
actions or causes of action of whatever kind resulting from, arising out of or in any matter relating to any such use, attachments or
modications.
At least two qualied people should perform the assembly procedure. Personal injury and/or property damage can result from dropping
or mishandling the TV.
If mounting to wall studs, make sure that the mounting screws are anchored into the center of the wall studs. Use of an edge-to-edge
stud nder is recommended.
Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that the wall is clear of
electrical wires. Cutting or drilling into an electrical line may cause serious personal injury.
Make sure there are no water or natural gas lines inside the wall where the mount is to be located. Cutting or drilling into a water or gas
line may cause severe property damage or personal injury.
Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact.
Tools for Wood Stud Installation
Tools for All Installations
Tools for Concrete Wall Installation
Stud Finder
1/2”
1/4” Wood Drill Bit
1/2”
1/2”
3/8” Concrete Drill Bit
Protective Eyewear
1/2”
Phillips Screwdriver
1/2”
Power Drill
1/2”
Pencil
Level
1/2”
Socket Wrench w/
1/2” Socket
1/2”
Tape Measure
1/2”
Hammer
1/2”
1/2” Combination
Wrench
1/2”

3
Ensure your package includes the following hardware and components before beginning installation. If any parts are missing and/or
damaged, stop the installation and call Séura at [phone].
In the Box
Tilt Brackets (2) Wall Plate
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3/8˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket M10 Socket*
2
1
5/16˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5/16˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
5/16” Stainless Steel
Flat Washers
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3/8˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket M10 Socket*
2
1
5/16˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5/16˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3/8˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket M10 Socket*
2
1
5/16˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5/16˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
1/4”-20 x 1-1/8” Stainless Steel
Bottom Locking Screws (2)
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3/8˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket M10 Socket*
2
1
5/16˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5/16˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3/8˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket M10 Socket*
2
1
5/16˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5/16˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
1/4”-20 x 1-3/4” Stainless Steel
Top Leveling Screws (2)
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3/8˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket M10 Socket*
2
1
5/16˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5/16˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
Twist Resistant Plastic Anchors (6)
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3/8˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket M10 Socket*
2
1
5/16˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5/16˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
Stainless Steel 5/16” X 3”Lag Bolts (6)
www.seura.com
1.800.95.SEURA
PH. 920.857.9069
FAX [phone]
SCALE REVISION
DESCRIPTION
BLACK POWDER COAT
1:8
A
AISI 304 STAINLESS STEEL
16 JUL 2018
DRAWN BY
TILT MOUNT ASSEMBLY VIEW
FINISH
Mount Assembly for Illustrations
1060.9
SIZE
1
PART NO.
SHEET 1 OF 2
MATERIAL
K. DEGROOT
DATE
SURFACE AREA
UNSPECIFIED TOLERANCES
FRACTIONAL: 1/16"
ANGULAR: 0.5
TWO PLACE DECIMAL: .03"
THREE PLACE DECIMAL: .015"
LASER CUTS: .005"
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DOCUMENT IS THE SOLE
PROPERTY OF THE MANUFACTURER.
ANY REPRODUCTION IN PART, OR
AS A WHOLE, WITHOUT THE
WRITTEN PERMISSION OF
MANUFACTURER, IS PROHIBITED.
2
www.seura.com
1.800.95.SEURA
PH. 920.857.9069
FAX [phone]
SCALE REVISION
DESCRIPTION
BLACK POWDER COAT
1:8
A
AISI 304 STAINLESS STEEL
16 JUL 2018
DRAWN BY
TILT MOUNT ASSEMBLY VIEW
FINISH
Mount Assembly for Illustrations
1060.9
SIZE
1
PART NO.
SHEET 1 OF 2
MATERIAL
K. DEGROOT
DATE
SURFACE AREA
UNSPECIFIED TOLERANCES
FRACTIONAL:
1/16"
ANGULAR: 0.5
TWO PLACE DECIMAL: .03"
THREE PLACE DECIMAL: .015"
LASER CUTS: .005"
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DOCUMENT IS THE SOLE
PROPERTY OF THE MANUFACTURER.
ANY REPRODUCTION IN PART, OR
AS A WHOLE, WITHOUT THE
WRITTEN PERMISSION OF
MANUFACTURER, IS PROHIBITED.
2
www.seura.com
1.800.95.SEURA
PH. 920.857.9069
FAX [phone]
SCALE REVISION
DESCRIPTION
BLACK POWDER COAT
1:8
A
AISI 304 STAINLESS STEEL
16 JUL 2018
DRAWN BY
TILT MOUNT ASSEMBLY VIEW
FINISH
Mount Assembly for Illustrations
1060.9
SIZE
1
PART NO.
SHEET 1 OF 2
MATERIAL
K. DEGROOT
DATE
SURFACE AREA
UNSPECIFIED TOLERANCES
FRACTIONAL:
1/16"
ANGULAR: 0.5
TWO PLACE DECIMAL: .03"
THREE PLACE DECIMAL: .015"
LASER CUTS: .005"
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DOCUMENT IS THE SOLE
PROPERTY OF THE MANUFACTURER.
ANY REPRODUCTION IN PART, OR
AS A WHOLE, WITHOUT THE
WRITTEN PERMISSION OF
MANUFACTURER, IS PROHIBITED.
2
Wall Mounting Hardware

4
Features
www.seura.com
1.800.95.SEURA
PH. 920.857.9069
FAX [phone]
SCALE REVISION
DESCRIPTION
BLACK POWDER COAT
1:8
A
AISI 304 STAINLESS STEEL
16 JUL 2018
DRAWN BY
TILT MOUNT ASSEMBLY VIEW
FINISH
Mount Assembly for Illustrations
1060.9
SIZE
1
PART NO.
SHEET 1 OF 2
MATERIAL
K. DEGROOT
DATE
SURFACE AREA
UNSPECIFIED TOLERANCES
FRACTIONAL:
1/16"
ANGULAR: 0.5
TWO PLACE DECIMAL: .03"
THREE PLACE DECIMAL: .015"
LASER CUTS: .005"
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DOCUMENT IS THE SOLE
PROPERTY OF THE MANUFACTURER.
ANY REPRODUCTION IN PART, OR
AS A WHOLE, WITHOUT THE
WRITTEN PERMISSION OF
MANUFACTURER, IS PROHIBITED.
2
Top Leveling Screws
Allows for leveling
adjustments of the TV
after mounting.
Tilt Locking Bolts
Allows for tilt angle of
the TV adjustment.
Mounting Slots
Allow for a variety of stud
congurations and lateral
shift adjustments when
mounting your TV.
Boom Locking Screws
Prevents the TV from
being removed or
dislodged from the wall
plate.
Cable/Electrical Cut Out
A large opening on the
wall plate allows for easy
cable access and power
distribution installations.
Directional
Mounting Arrows
The arrow lets you
know which edge
is up.
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3/8˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket M10 Socket*
2
1
5/16
˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5/16
˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3/8˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket M10 Socket*
2
1
5/16
˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5/16
˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)

5
Installing the Wall Plate
P5080T
Page 6 Visit the Premier Mounts website at http://www.premiermounts.com Installation Instructions
Installing the Wall Plate
Introduction
Directional Mounting Arrow
The Directional Mounting Arrow stamped into the
top of the P5080T wall mount indicates which
edge is the top.
Mounting Safety
Two people are recommended to install this
mount.
Wood Stud Installation
You must secure the wall plate to three (3) wall
studs with a minimum of six (6) lag bolts (2 lag
bolts for each stud found).
 Use a stud nder to determine the exact center of
wall studs in the vicinity of the wall plate.
® Use a pencil to mark the exact center of each of the
wall studs.
Step 1
Step 2
Two people are recommended for this step: one
person to level the wall plate and another person
to mark the wall stud location.
 Place the wall plate against the wall in the desired
viewing location.
® Adjust the wall plate to align the mount slots in the
wall plate with the center of the wall studs.
¯ Level the wall plate.
° Use a pencil to mark the upper-right mounting
location along the center of the wall stud.
If you will be installing your P5080T mount to
wood studs, proceed to the “Wood Stud
Installation” section.
If you will be installing your P5080T mount to a concrete
wall, proceed to the “Concrete Installation” section.
If you will be installing your P5080T mount to a steel
frame, proceed to the “Steel Stud Installation”
section.
Determining the Mounting Surface
X
XX
C
onc
rete
St
ee
l
St
u
d
Wo
o
d
St
u
d
P5080T
Page 6 Visit the Premier Mounts website at http://www.premiermounts.com Installation Instructions
Installing the Wall Plate
Introduction
Directional Mounting Arrow
The Directional Mounting Arrow stamped into the
top of the P5080T wall mount indicates which
edge is the top.
Mounting Safety
Two people are recommended to install this
mount.
Wood Stud Installation
You must secure the wall plate to three (3) wall
studs with a minimum of six (6) lag bolts (2 lag
bolts for each stud found).
 Use a stud nder to determine the exact center of
wall studs in the vicinity of the wall plate.
® Use a pencil to mark the exact center of each of the
wall studs.
Step 1
Step 2
Two people are recommended for this step: one
person to level the wall plate and another person
to mark the wall stud location.
 Place the wall plate against the wall in the desired
viewing location.
® Adjust the wall plate to align the mount slots in the
wall plate with the center of the wall studs.
¯ Level the wall plate.
° Use a pencil to mark the upper-right mounting
location along the center of the wall stud.
If you will be installing your P5080T mount to
wood studs, proceed to the “Wood Stud
Installation” section.
If you will be installing your P5080T mount to a concrete
wall, proceed to the “Concrete Installation” section.
If you will be installing your P5080T mount to a steel
frame, proceed to the “Steel Stud Installation”
section.
Determining the Mounting Surface
X
XX
C
onc
rete
St
ee
l
St
u
d
Wo
o
d
St
u
d
P5080T
Page 6 Visit the Premier Mounts website at http://www.premiermounts.com Installation Instructions
Installing the Wall Plate
Introduction
Directional Mounting Arrow
The Directional Mounting Arrow stamped into the
top of the P5080T wall mount indicates which
edge is the top.
Mounting Safety
Two people are recommended to install this
mount.
Wood Stud Installation
You must secure the wall plate to three (3) wall
studs with a minimum of six (6) lag bolts (2 lag
bolts for each stud found).
 Use a stud nder to determine the exact center of
wall studs in the vicinity of the wall plate.
® Use a pencil to mark the exact center of each of the
wall studs.
Step 1
Step 2
Two people are recommended for this step: one
person to level the wall plate and another person
to mark the wall stud location.
 Place the wall plate against the wall in the desired
viewing location.
® Adjust the wall plate to align the mount slots in the
wall plate with the center of the wall studs.
¯ Level the wall plate.
° Use a pencil to mark the upper-right mounting
location along the center of the wall stud.
If you will be installing your P5080T mount to
wood studs, proceed to the “Wood Stud
Installation” section.
If you will be installing your P5080T mount to a concrete
wall, proceed to the “Concrete Installation” section.
If you will be installing your P5080T mount to a steel
frame, proceed to the “Steel Stud Installation”
section.
Determining the Mounting Surface
X
XX
C
onc
rete
St
ee
l
St
u
d
Wo
o
d
St
u
d
www.seura.com
1.800.95.SEURA
PH. 920.857.9069
FAX [phone]
SCALE REVISION
DESCRIPTION
BLACK POWDER COAT
1:8
A
AISI 304 STAINLESS STEEL
16 JUL 2018
DRAWN BY
TILT MOUNT ASSEMBLY VIEW
FINISH
Mount Assembly for Illustrations
1060.9
SIZE
1
PART NO.
SHEET 1 OF 2
MATERIAL
K. DEGROOT
DATE
SURFACE AREA
UNSPECIFIED TOLERANCES
FRACTIONAL: 1/16"
ANGULAR: 0.5
TWO PLACE DECIMAL: .03"
THREE PLACE DECIMAL: .015"
LASER CUTS: .005"
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DOCUMENT IS THE SOLE
PROPERTY OF THE MANUFACTURER.
ANY REPRODUCTION IN PART, OR
AS A WHOLE, WITHOUT THE
WRITTEN PERMISSION OF
MANUFACTURER, IS PROHIBITED.
2
www.seura.com
1.800.95.SEURA
PH. 920.857.9069
FAX [phone]
SCALE REVISION
DESCRIPTION
BLACK POWDER COAT
1:8
A
AISI 304 STAINLESS STEEL
16 JUL 2018
DRAWN BY
TILT MOUNT ASSEMBLY VIEW
FINISH
Mount Assembly for Illustrations
1060.9
SIZE
1
PART NO.
SHEET 1 OF 2
MATERIAL
K. DEGROOT
DATE
SURFACE AREA
UNSPECIFIED TOLERANCES
FRACTIONAL: 1/16"
ANGULAR: 0.5
TWO PLACE DECIMAL: .03"
THREE PLACE DECIMAL: .015"
LASER CUTS: .005"
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DOCUMENT IS THE SOLE
PROPERTY OF THE MANUFACTURER.
ANY REPRODUCTION IN PART, OR
AS A WHOLE, WITHOUT THE
WRITTEN PERMISSION OF
MANUFACTURER, IS PROHIBITED.
2
Before installation, please note:
The directional mounting arrow punched out of the mount wall
plate indicates which direction is up.
Two people are recommended to install this product.
Determining the Mounting Surface
If you will be installing your Outdoor TV Wall Mount to wood
studs, proceed to the “Wood Stud Installation” section.
If you will be installing to a concrete wall, proceed to the
“Concrete Installation” section.
Step 1
You must secure the wall plate to three (3) wall studs with a
minimum of six (6) lag bolts *2 lag bolts for each stud).
1. Use a stud nder to determine the exact center of wall studs
in the vicinity of the wall plate.
2. Use a pencil to mark the exact center of the wall studs.
Step 2
Two people are recommended for this step: one person to
level the wall plate and another person to mark the wall stud
location.
1. Place the wall plate against the wall in the desired viewing
location
2. Adjust the wall plate to align the mount slots in the wall
plate with the center of the wall studs.
3. Level the wall plate.
4. Use a pencil to mark the upper-right mounting location along
the center of the wall stud.
Wood Stud Installation

6
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 7
Installing the Wall Plate (cont’d)
 Place the wall plate against the wall and align it with
the pilot hole.
® Insert one (1) 5/16″ x 3″ lag bolt and one (1) 5/16″
washer into the upper right mounting hole and
tighten using a socket wrench and ½″ socket.
Do not overtighten the lag bolt.
Step 4
Step 3
Step 5
Step 6
Drill a “pilot hole” in the center of the upper-right mark
using a ¼″ drill bit and power drill.
Only use a ¼″ drill bit when drilling the pilot holes.
 Level the wall plate.
® Use a pencil to mark the remaining ve (5) mounting
locations along the center of each wall stud.
Two people are recommended for this step: one
person to level the wall plate and another person
to drill the pilot holes.
Drill a “pilot hole” in the center of each of the marks with
a power drill and a ¼″ drill bit.
Only use ¼″ drill bit when drilling the pilot holes.
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 7
Installing the Wall Plate (cont’d)
 Place the wall plate against the wall and align it with
the pilot hole.
® Insert one (1) 5/16″ x 3″ lag bolt and one (1) 5/16″
washer into the upper right mounting hole and
tighten using a socket wrench and ½″ socket.
Do not overtighten the lag bolt.
Step 4
Step 3
Step 5
Step 6
Drill a “pilot hole” in the center of the upper-right mark
using a ¼″ drill bit and power drill.
Only use a ¼″ drill bit when drilling the pilot holes.
 Level the wall plate.
® Use a pencil to mark the remaining ve (5) mounting
locations along the center of each wall stud.
Two people are recommended for this step: one
person to level the wall plate and another person
to drill the pilot holes.
Drill a “pilot hole” in the center of each of the marks with
a power drill and a ¼″ drill bit.
Only use ¼″ drill bit when drilling the pilot holes.
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 7
Installing the Wall Plate (cont’d)
 Place the wall plate against the wall and align it with
the pilot hole.
® Insert one (1) 5/16″ x 3″ lag bolt and one (1) 5/16″
washer into the upper right mounting hole and
tighten using a socket wrench and ½″ socket.
Do not overtighten the lag bolt.
Step 4
Step 3
Step 5
Step 6
Drill a “pilot hole” in the center of the upper-right mark
using a ¼″ drill bit and power drill.
Only use a ¼″ drill bit when drilling the pilot holes.
 Level the wall plate.
® Use a pencil to mark the remaining ve (5) mounting
locations along the center of each wall stud.
Two people are recommended for this step: one
person to level the wall plate and another person
to drill the pilot holes.
Drill a “pilot hole” in the center of each of the marks with
a power drill and a ¼″ drill bit.
Only use ¼″ drill bit when drilling the pilot holes.
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 7
Installing the Wall Plate (cont’d)
 Place the wall plate against the wall and align it with
the pilot hole.
® Insert one (1) 5/16″ x 3″ lag bolt and one (1) 5/16″
washer into the upper right mounting hole and
tighten using a socket wrench and ½″ socket.
Do not overtighten the lag bolt.
Step 4
Step 3
Step 5
Step 6
Drill a “pilot hole” in the center of the upper-right mark
using a ¼″ drill bit and power drill.
Only use a ¼″ drill bit when drilling the pilot holes.
 Level the wall plate.
® Use a pencil to mark the remaining ve (5) mounting
locations along the center of each wall stud.
Two people are recommended for this step: one
person to level the wall plate and another person
to drill the pilot holes.
Drill a “pilot hole” in the center of each of the marks with
a power drill and a ¼″ drill bit.
Only use ¼″ drill bit when drilling the pilot holes.
Installing the Wall Plate : Wood Stud Installation Cont.
P5080T
Page 8 Visit the Premier Mounts website at http://www.premiermounts.com Installation Instructions
The supplied 5/16″ concrete wedge anchors must be
used for concrete installation.
You will need a 5/16″ concrete drill bit, which is
available at your closest hardware store.
Concrete Installation
Installing the Wall Plate (cont’d)
Two people are recommended for this step: one
person to level the wall plate and another person
to mark the mounting locations.
 Place the wall plate against the wall in the desired
viewing location.
® Level the wall plate.
¯ Use a pencil and mark 3 upper and 3 lower
mounting locations where you will be drilling holes
for the concrete wedge anchors. Each horizontal
location cannot be closer than 12″ apart.
° Set the wall plate to one side in a safe location.
Step 1
Use a power drill and 5/16″ concrete drill bit to drill a hole
at each of the marks.
Step 2
Step 7
 Insert one (1) 5/16″ x 3″ lag bolt and one (1) 5/16″ washer
into each pilot hole.
® Tighten all lag bolts using a socket wrench and ½″
socket.
Do not overtighten the lag bolts when attaching the
mount to the wall. Improper installation may result in
personal injury or property damage.
Proceed to the “Installing the Mounting Bracket”
section.
Concrete Wedge Anchors
Example of 5/16″ Concrete Drill Bit (Not Included)
>12” >12”
Step 3
Drill a pilot hole in the center of the upper-right mark using a
1/4” drill bit and power drill.
Step 6
Two people are recommended for this step: one person to level
the wall plate and another person to drill the pilot holes.
Drill a pilot hole in the center of each of the marks with a
power drill and a 1/4” drill bit.
Step 7
1. Insert one (1) 5/16” x 3” lag bolt and one (1) 5/16” washer into each
pilot hole.
2. Tighten all lag bolts using a socket wrench and 1/2” socket.
Do not overtighten the lag bolts when aaching the mount to the wall.
Improper installation may result in personal injury or property damage.
Proceed to the “Installing the Mounting Bracket” section.
Step 4
1. Place the wall plate against the wall and align it with the
pilot hole.
2. Insert one (1) 5/16” x 3” lag bolt and one (1) 5/16” washer into
the upper right mounting hole and tighten using a socket
wrench and 1/2” socket. Do not overtighten the lag bolt.
Step 5
1. Level the wall plate.
2. Use a pencil to mark the remaining ve (5) mounting
locations along the center of each wall stud.

7
Installing the Wall Plate: Concrete Wall Installation
P5080T
Page 8 Visit the Premier Mounts website at http://www.premiermounts.com Installation Instructions
The supplied 5/16″ concrete wedge anchors must be
used for concrete installation.
You will need a 5/16″ concrete drill bit, which is
available at your closest hardware store.
Concrete Installation
Installing the Wall Plate (cont’d)
Two people are recommended for this step: one
person to level the wall plate and another person
to mark the mounting locations.
 Place the wall plate against the wall in the desired
viewing location.
® Level the wall plate.
¯ Use a pencil and mark 3 upper and 3 lower
mounting locations where you will be drilling holes
for the concrete wedge anchors. Each horizontal
location cannot be closer than 12″ apart.
° Set the wall plate to one side in a safe location.
Step 1
Use a power drill and 5/16″ concrete drill bit to drill a hole
at each of the marks.
Step 2
Step 7
 Insert one (1) 5/16″ x 3″ lag bolt and one (1) 5/16″ washer
into each pilot hole.
® Tighten all lag bolts using a socket wrench and ½″
socket.
Do not overtighten the lag bolts when attaching the
mount to the wall. Improper installation may result in
personal injury or property damage.
Proceed to the “Installing the Mounting Bracket”
section.
Concrete Wedge Anchors
Example of 5/16″ Concrete Drill Bit (Not Included)
>
12” >12”
P5080T
Page 8 Visit the Premier Mounts website at http://www.premiermounts.com Installation Instructions
The supplied 5/16″ concrete wedge anchors must be
used for concrete installation.
You will need a 5/16″ concrete drill bit, which is
available at your closest hardware store.
Concrete Installation
Installing the Wall Plate (cont’d)
Two people are recommended for this step: one
person to level the wall plate and another person
to mark the mounting locations.
 Place the wall plate against the wall in the desired
viewing location.
® Level the wall plate.
¯ Use a pencil and mark 3 upper and 3 lower
mounting locations where you will be drilling holes
for the concrete wedge anchors. Each horizontal
location cannot be closer than 12″ apart.
° Set the wall plate to one side in a safe location.
Step 1
Use a power drill and 5/16″ concrete drill bit to drill a hole
at each of the marks.
Step 2
Step 7
 Insert one (1) 5/16″ x 3″ lag bolt and one (1) 5/16″ washer
into each pilot hole.
® Tighten all lag bolts using a socket wrench and ½″
socket.
Do not overtighten the lag bolts when attaching the
mount to the wall. Improper installation may result in
personal injury or property damage.
Proceed to the “Installing the Mounting Bracket”
section.
Concrete Wedge Anchors
Example of 5/16″ Concrete Drill Bit (Not Included)
>12” >12”
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3/8˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket M10 Socket*
2
1
5/16˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5/16˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
Plastic Anchors for Brick and Stone
P5080T
Page 8 Visit the Premier Mounts website at http://www.premiermounts.com Installation Instructions
The supplied 5/16″ concrete wedge anchors must be
used for concrete installation.
You will need a 5/16″ concrete drill bit, which is
available at your closest hardware store.
Concrete Installation
Installing the Wall Plate (cont’d)
Two people are recommended for this step: one
person to level the wall plate and another person
to mark the mounting locations.
 Place the wall plate against the wall in the desired
viewing location.
® Level the wall plate.
¯ Use a pencil and mark 3 upper and 3 lower
mounting locations where you will be drilling holes
for the concrete wedge anchors. Each horizontal
location cannot be closer than 12″ apart.
° Set the wall plate to one side in a safe location.
Step 1
Use a power drill and 5/16″ concrete drill bit to drill a hole
at each of the marks.
Step 2
Step 7
 Insert one (1) 5/16″ x 3″ lag bolt and one (1) 5/16″ washer
into each pilot hole.
® Tighten all lag bolts using a socket wrench and ½″
socket.
Do not overtighten the lag bolts when attaching the
mount to the wall. Improper installation may result in
personal injury or property damage.
Proceed to the “Installing the Mounting Bracket”
section.
Concrete Wedge Anchors
Example of 5/16″ Concrete Drill Bit (Not Included)
>12” >12”
Concrete Wall Installation
You will need a 3/8” concrete drill bit
and the enclosed 5/16” twist resistant
plastic anchors for concrete installation.
Step 1
Two people are recommended for this step: one person to
level the wall plate and another person to mark the mounting
locations.
1. Place the wall plate against the wall in the desired viewing
location.
2. Level the wall plate.
3. Use a pencil and mark 3 upper and 3 lower mounting
locations where you will be drilling holes for the plastic
concrete anchors. Each horizontal location cannot be closer
than 12” apart. Set the wall plate aside for now.
Step 2
Use a power drill and 10 mm concrete drill bit to drill a hole at
each of the marks.
3/8” Concrete Drill Bit (not included)
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 9
 Insert a concrete wedge anchor into each hole.
If necessary, lightly tap each concrete wedge anchor
into place with a hammer.
® Remove the nuts and washers from all six (6)
concrete wedge anchors.
Step 3
 Place the wall plate against the wall over the
threaded shafts of the concrete wedge anchors.
® Replace the washers which you removed from
the concrete wedge anchors with the 5/16″ washers
shown in the parts list on Page 3.
¯ Attach the nuts and 5/16″ washers to each of the
concrete wedge anchors and tighten using a socket
wrench and an M10 socket.
Do not overtighten the wedge anchor nuts.
Proceed to the “Installing the Mounting Bracket”
section.
Step 4
Installing the Wall Plate (cont’d)
Step 1
Steel Stud Installation
 Identify the general location on the wall where you
will be mounting your at panel.
® Use a stud nder to determine the exact center
of each steel stud in the vicinity of the mounting
location.
¯ Use a pencil and mark the exact center of each
steel stud.
The supplied M6 steel stud anchors must be used
to install your Premier Mounts’ mount to steel
studs. Do not use lag bolts or wood screws.
Steel Stud Anchor Screw Steel Stud Anchor Sleeve
X
X
X
1/2”
Step 3
Insert a plastic anchor into each hole. If necessary, lightly tap
each concrete anchor into place with a hammer.
Step 4
1. Insert one (1) 5/16” x 3” lag bolt and one (1) 5/16” washer into
each anchor.
2. Tighten all lag bolts using a socket wrench and 1/2” socket.
Do not overtighten the lag bolts when aaching the mount to
the wall. Improper installation may result in personal injury or
property damage.
Proceed to the “Installing the Mounting Bracket” section.

8
Installing the Mounting Bracket
Locking Screw Installation
You must install the top leveling screws and the bottom locking
screws before you attach the mounting bracket to the back of
the at panel. The top leveling screws consist of (2) 1/4-20 x
1-3/4” screws and the bottom locking screws consist of (2) 1/4-
20 x 1-1/8” screws.
Thread one (1) leveling screw into the top hole and one (1)
locking screw into the bottom hole on each of the mounting
brackets. Make sure the locking screw is securely threaded into
the mounting tab before proceeding.
Do not thread the screws any further once it is even with the
mounting tab. Threading the screws further will prevent you
from safely attaching the at panel to the wall plate.
Aaching the Mounting Bracket to the TV
1. Place your TV screen side down on a soft, at surface.
2. Identify the location of the VESA threaded inserts on the
back of your TV and align the holes in each mounting
bracket.
3. Secure each mounting bracket to your TV by inserting two (2)
screws per bracket.
Do not overtighten the mounting hardware.
Locking Screw Installation
Installing the Mounting Bracket (cont’d)
You must install the locking screws before you
panel. The locking screws consists of two (2) M6 x
120mm screws.
Thread one (1) locking screw into the bottom mounting
hole on each of the mounting brackets. Make sure the
locking screw is securely threaded into the mounting tab
before proceeding.
Do not thread the locking screw any further once
it is even with the mounting tab. Threading the
locking screw any further will prevent you from
Proceed to the “Attaching the Mounting Bracket to
the Flat Panel” section.
Locking Screw
Correctly Threaded
Locking Screw
Threaded Too Far
Security Barrel Installation (Optional)
Do not overtighten the locking screw.
Please read the following directions to install the
security barrel:
Remove the locking screw from the mounting
1.
2.
3.
4.
bracket.
Place the locking screw into and through the
security barrel (see illustration below).
Re-insert the locking screw and security
components into the mounting bracket.
Tighten the locking screw and security components
until seated in the mounting tab.
- PCB-CSL1 (sold separately)
- Padlock (Combination or Keyed; commercially
available)
Security
Barrel
Locking Screw
Do not thread the locking screw any further once
it is even with the mounting tab (see illustration to
the right). Threading the locking screw any further
panel to the wall plate.
Proceed to the “Attaching the Mounting Bracket to
the Flat Panel” section.
Mounting Tab
Locking Screw
Correctly Threaded
Locking Screw Installation
Installing the Mounting Bracket (cont’d)
You must install the locking screws before you
panel. The locking screws consists of two (2) M6 x
120mm screws.
Thread one (1) locking screw into the bottom mounting
hole on each of the mounting brackets. Make sure the
locking screw is securely threaded into the mounting tab
before proceeding.
Do not thread the locking screw any further once
it is even with the mounting tab. Threading the
locking screw any further will prevent you from
Proceed to the “Attaching the Mounting Bracket to
the Flat Panel” section.
Locking Screw
Correctly Threaded
Locking Screw
Threaded Too Far
Security Barrel Installation (Optional)
Do not overtighten the locking screw.
Please read the following directions to install the
security barrel:
Remove the locking screw from the mounting
1.
2.
3.
4.
bracket.
Place the locking screw into and through the
security barrel (see illustration below).
Re-insert the locking screw and security
components into the mounting bracket.
Tighten the locking screw and security components
until seated in the mounting tab.
- PCB-CSL1 (sold separately)
- Padlock (Combination or Keyed; commercially
available)
Security
Barrel
Locking Screw
Do not thread the locking screw any further once
it is even with the mounting tab (see illustration to
the right). Threading the locking screw any further
panel to the wall plate.
Proceed to the “Attaching the Mounting Bracket to
the Flat Panel” section.
Mounting Tab
Locking Screw
Threaded Too Far
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3
/
8
˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket M10 Socket*
2
1
5/16
˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5/16
˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
www.seura.com
1.800.95.SEURA
PH. 920.857.9069
FAX [phone]
SCALE REVISION
DESCRIPTION
BLACK POWDER COAT
1:8
A
AISI 304 STAINLESS STEEL
16 JUL 2018
DRAWN BY
TILT MOUNT ASSEMBLY VIEW
FINISH
Mount Assembly for Illustrations
1060.9
SIZE
1
PART NO.
SHEET 1 OF 2
MATERIAL
K. DEGROOT
DATE
SURFACE AREA
UNSPECIFIED TOLERANCES
FRACTIONAL: 1/16"
ANGULAR: 0.5
TWO PLACE DECIMAL: .03"
THREE PLACE DECIMAL: .015"
LASER CUTS: .005"
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DOCUMENT IS THE SOLE
PROPERTY OF THE MANUFACTURER.
ANY REPRODUCTION IN PART, OR
AS A WHOLE, WITHOUT THE
WRITTEN PERMISSION OF
MANUFACTURER, IS PROHIBITED.
2
This section requires two people.
that the top and bottom hooks of both mounting
brackets are securely seated on the upper and
lower mounting rails of the wall panel.
mounting rails on the wall panel.
the wall.
Connect the top and bottom mounting brackets to
the rails of the wall plate.
Attaching the Flat Panel to the Wall Plate
This section assumes that you have read and
understood these sections:
●Selecting the Proper Mounting Hardware
●Universal Washer Installation
●Universal Spacer Installation
surface.
1.
2.
3.
4.
1.
2.
3.
Identify the number and location of the thread
Align the holes on each mounting bracket with the
inserting a minimum of two (2) screws per bracket.
Do not overtighten the mounting hardware.
Proceed to the “Attaching the Flat Panel to the Wall
Plate” section.
Attaching the Mounting Bracket to the Flat Panel

9
This section requires two people.
that the top and bottom hooks of both mounting
brackets are securely seated on the upper and
lower mounting rails of the wall panel.
mounting rails on the wall panel.
the wall.
Connect the top and bottom mounting brackets to
the rails of the wall plate.
Attaching the Flat Panel to the Wall Plate
This section assumes that you have read and
understood these sections:
●Selecting the Proper Mounting Hardware
●Universal Washer Installation
●Universal Spacer Installation
surface.
1.
2.
3.
4.
1.
2.
3.
Identify the number and location of the thread
Align the holes on each mounting bracket with the
inserting a minimum of two (2) screws per bracket.
Do not overtighten the mounting hardware.
Proceed to the “Attaching the Flat Panel to the Wall
Plate” section.
Attaching the Mounting Bracket to the Flat Panel
This section requires two people.
that the top and bottom hooks of both mounting
brackets are securely seated on the upper and
lower mounting rails of the wall panel.
mounting rails on the wall panel.
the wall.
Connect the top and bottom mounting brackets to
the rails of the wall plate.
Attaching the Flat Panel to the Wall Plate
This section assumes that you have read and
understood these sections:
●Selecting the Proper Mounting Hardware
●Universal Washer Installation
●Universal Spacer Installation
surface.
1.
2.
3.
4.
1.
2.
3.
Identify the number and location of the thread
Align the holes on each mounting bracket with the
inserting a minimum of two (2) screws per bracket.
Do not overtighten the mounting hardware.
Proceed to the “Attaching the Flat Panel to the Wall
Plate” section.
Attaching the Mounting Bracket to the Flat Panel
Installing the Mounting Bracket
Aaching the TV to the Wall Plate
This section requires two people.
Do not let go of the TV until you are certain that the top and
bottom hooks of both mounting brackets are securely engaged
on the upper and lower mounting rails of the wall plate.
1. Raise the TV above the top and bottom mounting rails on the
wall panel.
2. Slide the at panel down slowly, keeping it close to the wall.
3. Connect the top and bottom mounting brackets to the rails
of the wall plate.

10
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 15
Leveling Screw Adjustment
If your at panel is tilted too far to one side, the leveling
screws will allow you to compensate for this tilt by
adjusting the screws with a screwdriver.
 Loosen both locking screws.
® Adjust the tilt of your at panel.
¯ Tighten both locking screws.
Caution!
It is possible to dislodge your at panel while you
level your at panel. Use extreme caution until
you tighten the locking screws.
Mounting Bracket Adjustments
Locking Screw Adjustment
After you have nished leveling your at panel, be sure
to tighten the two (2) M6 x 120mm locking screws.
Do not overtighten the locking screws.
M6 x 120mm
Locking Screw
(1 per Bracket)
M6 x 30mm
Leveling Screw
(1 per Bracket)
Tilt Adjustment
Adjusting the Flat Panel Friction Tilt Angle
 Place one hand at the center-top edge of the at
panel.
® Place the other hand on the center-bottom edge of
the at panel.
¯ Using the upper hand, gently pull the top of the
at panel towards you while the lower hand gently
pushes the bottom of the at panel away from you.
Adjusting the Flat Panel to the Original Position
 Place one hand at the center-top edge of the at
panel.
® Place the other hand on the center-bottom edge of
the at panel.
¯ Using the upper hand, gently push the top of the at
panel towards the wall while the lower hand gently
pulls the bottom of the at panel away from the wall.
Mounting Bracket Adjustment
Top Leveling Screw Adjustment
If your TV is not level, the Top Leveling Screws will allow you
to compensate for this tilt by adjusting the screws with a
screwdriver.
1. Loosen both locking screws.
2. Adjust the tilt of your TV.
3. Tighten both locking screws.
Caution: It is possible to dislodge your TV while you level it.
Use extreme caution until you tighten the locking screws.
Boom Locking Screw Adjustment
After you have adjusted leveling the TV, tighten the two (2)
bottom locking screws.
Do not overtighten the locking screws.
Tilt Adjustment
Adjusting the TV Friction Tilt Angle
1. Place on e hand at the center-top edge of the TV.
2. Place the other hand on the center-bottom edge of the at
panel.
3. Using the upper hand, gently pull the top of the at panel
towards you while the lower hand gently pushes the bottom
of the at panel away from you.
Adjusting the Flat Panel to the Original Position
1. Place on hand at the center-top edge of the at panel.
2. Place the other hand on the center-bottom edge of the at
panel.
3. Using the upper hand, gently push the top of the at panel
towards the wall while the lower hand gently pulls the
bottom of the at panel away from the wall.
After tilt is adjusted to the desired position, tighten the (2)
tilt locking bolts on each bracket until the brackets are rmly
secured.
Do not overtighten the Tilt Locking Bolts.
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3/8˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket M10 Socket*
2
1
5/16
˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5/16
˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
www.seura.com
1.800.95.SEURA
PH. 920.857.9069
FAX [phone]
SCALE REVISION
DESCRIPTION
BLACK POWDER COAT
1:8
A
AISI 304 STAINLESS STEEL
16 JUL 2018
DRAWN BY
TILT MOUNT ASSEMBLY VIEW
FINISH
Mount Assembly for Illustrations
1060.9
SIZE
1
PART NO.
SHEET 1 OF 2
MATERIAL
K. DEGROOT
DATE
SURFACE AREA
UNSPECIFIED TOLERANCES
FRACTIONAL: 1/16"
ANGULAR: 0.5
TWO PLACE DECIMAL: .03"
THREE PLACE DECIMAL: .015"
LASER CUTS: .005"
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DOCUMENT IS THE SOLE
PROPERTY OF THE MANUFACTURER.
ANY REPRODUCTION IN PART, OR
AS A WHOLE, WITHOUT THE
WRITTEN PERMISSION OF
MANUFACTURER, IS PROHIBITED.
2
Top Leveling Screw
Allows for leveling
adjustments of the TV
after mounting.
Boom Locking Screw
Prevents the TV from
being removed or
dislodged from the wall
plate.
Tilt Locking
Bolts

11
Technical Specications
www.seura.com
1.800.95.SEURA
PH. 920.857.9069
FAX [phone]
996.16
39.22
38.35
1.51
953.83
37.55
400
15.75
25.4
1.00
25.4
1.00
146.05
5.75
197.64
7.78
406.4
16.00
609.6
24.00
406.4
16.00
406.4
16.00
812.8
32.00
C
L
516.26
20.33
48.66
1.92
285.75
11.25
333.95
13.15
996.16
39.22
SCALE REVISION
DESCRIPTION
BLACK POWDER COAT
1:8
A
AISI 304 STAINLESS STEEL
16 JUL 2018
DRAWN BY
TILT MOUNT ASSEMBLY VIEW
FINISH
Mount Assembly for Install
1060.9
SIZE
1
PART NO.
SHEET 1 OF 2
MATERIAL
K. DEGROOT
DATE
SURFACE AREA
UNSPECIFIED TOLERANCES
FRACTIONAL: 1/16"
ANGULAR: 0.5
TWO PLACE DECIMAL: .03"
THREE PLACE DECIMAL: .015"
LASER CUTS: .005"
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DOCUMENT IS THE SOLE
PROPERTY OF THE MANUFACTURER.
ANY REPRODUCTION IN PART, OR
AS A WHOLE, WITHOUT THE
WRITTEN PERMISSION OF
MANUFACTURER, IS PROHIBITED.
2
www.seura.com
1.800.95.SEURA
PH. 920.857.9069
FAX [phone]
996.16
39.22
38.35
1.51
953.83
37.55
400
15.75
25.4
1.00
25.4
1.00
146.05
5.75
197.64
7.78
406.4
16.00
609.6
24.00
406.4
16.00
406.4
16.00
812.8
32.00
C
L
516.26
20.33
48.66
1.92
285.75
11.25
333.95
13.15
996.16
39.22
SCALE REVISION
DESCRIPTION
BLACK POWDER COAT
1:8
A
AISI 304 STAINLESS STEEL
16 JUL 2018
DRAWN BY
TILT MOUNT ASSEMBLY VIEW
FINISH
Mount Assembly for Install
1060.9
SIZE
1
PART NO.
SHEET 1 OF 2
MATERIAL
K. DEGROOT
DATE
SURFACE AREA
UNSPECIFIED TOLERANCES
FRACTIONAL: 1/16"
ANGULAR: 0.5
TWO PLACE DECIMAL: .03"
THREE PLACE DECIMAL: .015"
LASER CUTS: .005"
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DOCUMENT IS THE SOLE
PROPERTY OF THE MANUFACTURER.
ANY REPRODUCTION IN PART, OR
AS A WHOLE, WITHOUT THE
WRITTEN PERMISSION OF
MANUFACTURER, IS PROHIBITED.
2
Maximum Flat Panel Weight: 250 lbs.
The wall structure must be capable of supporting at least four times the weight of the TV. If not, the wall structure must be reinforced.
Dimensions
All measurements are in inches [milimeters]

Publish date: February 25, 2019. Information is subject to change without notice.
© 2019 Séura
1230 Ontario Road Green Bay, Wisconsin 54311
1-800-957-3872 [e-mail]
www.seura.com
LIMITED PRODUCT WARRANTY
1230 Ontario Road Green Bay, Wisconsin 54311
1-800-957-3872 [e-mail]
www.seura.com
Publish date: January 7, 2019. Information is subject to change without notice.
© 2019 Séura
The standard limited warranty policies of Séura, Inc. (“Séura”) shall apply to all equipment or
other goods (“Products”) at the time of sale to any authorized Séura distributor and/or product
reseller. These warranty policies may be modied by Séura from time to time. Copies of the
standard limited warranties then in effect for a particular Product will be made available upon
request and are also available on the Séura website at https://www.seura.com/warranty/. This
warranty is valid only with respect to Product sales in the U.S. and Canada.
If any Product fails to work or operate properly because of a defect in materials or workmanship,
Séura will, if notied of such defect within the applicable warranty period indicated below,
at its option, either: (a) repair the Product with new or refurbished parts onsite or at Séura’s
factory, including Séura’s labor if applicable; or (b) replace the Product with a new or
refurbished Product; or (c) if repair or replacement is not commercially feasible, refund an
amount equal to a pro rata share of the current MSRP (as determined by the remainder of the
warranty period). The remedy chosen will be in good faith and at the discretion of Séura. In no
event will Séura be responsible for any costs related to installation and/or removal of Product.
Séura warrants its Products as set forth below, which warranty periods shall start and run
from the date of Séura’s sale of the Product:
• Lighted Mirrors (excluding Select Lighted Mirrors) with respect to Séura’s labor, glass,
structure, and assembly for seven (7) years; electrical and LED light strips for ve (5)
years. Mirror technology with respect to Séura’s labor and parts including wireless music
technology, clocks, nightlights, defoggers, dimmers, and voice technology are covered
for two (2) years.
• Select Lighted Mirrors with respect to Séura’s labor, glass, structure, and assembly for
one (1) year; electrical and LED light strips for three (3) years.
• SMART Mirrors with respect to Séura’s labor, glass, structure, and assembly for three
(3) years; display including remote, power supply and SMART Technology for one (1) year.
• TV Mirrors with respect to Séura’s labor, glass, structure, and assembly for three (3)
years; TV including remote and power supply for two (2) years.
• Lighted TV Mirrors with respect to Séura’s labor, glass, structure, and assembly for three
(3) years; electrical and LED light strips for ve (5) years. TV including remote and power
supply for two (2) years.
• Indoor Waterproof TVs with respect to Séura’s labor, glass, structure, and assembly for
three (3) years; TV including remote and power supply for two (2) years.
• Outdoor Displays with respect to Séura’s labor, structure, assembly, display including
remote, and power supply for two (2) years.
• Indoor and Outdoor Mounts for two (2) years against defects in original hardware and/or
workmanship. Excludes corrosion or rust resulting from damaged, scratched or chipped
paint or other surfaces.
• Outdoor Soundbars with respect to labor and parts for one (1) year.
• Protective Display Covers for two (2) years against material and/or workmanship defects.
• Decorative Frames for one (1) year.
Exceptions to Warranty: This warranty is valid only with respect to Product sales in the U.S.
and Canada. Séura does not warrant Products against defects arising out of, related to, or
caused by, whether totally or partially, and whether directly or indirectly, any of the following:
A. Failing to properly clean and maintain, any Product, part or component of a Product,
including, but not limited to, lters, front bezel, and other Product areas or components;
B. A Product’s extended use, including particularly, commercial applications, where a
Product is operating on average more than twelve (12) hours per day on a permanent or
extended periodic basis;
C. Circumstances, damage (including concealed damage) or other conditions occurring
during shipment of a Product or at any time after a Product leaves Séura’s facility
(including without limitation transport of the Product to or from Séura before or after
authorized service). Products must be packed properly using original packaging or Séura
replacement or pre-authorized packaging. Customer assumes all risk, and costs, including
transportation costs, while Product is in transit to or from Séura;
D. Circumstances, damage or other conditions occurring during unpacking and/or removal
of a Product from its original packaging, including the removal of protective material;
E. Improper, incorrect, or insufcient AC supply voltage to a Product;
F. Alterations, modications, including use of unauthorized mount, or changes to a Product
without Séura’s prior written authorization;
G. The incorporation of a Product into or within a product of a third party, without Séura’s
prior written authorization;
H. A Product’s misuse, neglect use, abuse, or improper operation, including the failure to
follow a Product’s normal and ordinary operating instructions;
I. The effects of re, ood, lightning, electrical surges, water and other liquid inltration,
smoke, insect or animal infestation, sand, mud, chemicals, improper cleaning agents and
other substances not intended to come into contact with a Product, including any such
substances contact with a Product as the result of acts of God;
J. The improper or faulty installation, setup, or adjustment of a Product;
K. A Product’s repair, attempted repair, or total or partial disassembly by any party other
than a Séura authorized service representative;
L. When the Product occurs with pixel errors within the specied and permitted area. (For
more information about this, inquire directly with Séura regarding the Séura Pixel Policy.)
M. Corrosion that does not affect the performance of a Product or the reasonable cosmetic
appearance of a Product (including without limitation, scratches or other paint or nish
damage to a Product that lead to or are caused by, in part or in total, corrosion);
N. When a Lighted Mirror or Lighted TV Mirror using LEDs retains an overall brightness
greater than 70% of the original brightness, including cases whereas an individual LED
fails; and/or
O. Normal wear and tear on the Product.
Séura does not warrant that its Products will integrate with any third party products at
present or in the future. It is purchaser’s responsibility to test and verify compatibility. Further,
Séura does not warrant its software or programs, or any content downloaded after shipment.
It is the purchaser responsibility to take precautions to protect the product from malware,
viruses, data loss, and other potentially destructive programs.
Warranty Disqualiers. This Limited Warranty only extends to, and runs for the benet of,
the original purchaser of the Product and only covers a Product purchased new. All warranty
claims must be submitted together with original proof of purchase and any Product subject
to a warranty claim must retain its original Séura serial number. Séura reserves the right
to require any warranty claimant to produce the original purchase receipt or other original
purchase date proof as may be reasonably required by Séura to verify the Product’s warranty
eligibility. Séura shall have no liability with respect to Products whose serial number has been
removed, defaced, replaced, or otherwise tampered with in any manner. Séura reserves the
right to examine all failed product components and determine, in its sole discretion, whether
any product components are defective and covered under warranty.
LIMITATION OF LIABILITY. THE EXPRESS LIMITED WARRANTIES SET FORTH HEREIN ARE IN
LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR USE. SÉURA WILL NOT BE LIABLE FOR ANY DAMAGE TO OTHER
PROPERTY CAUSED BY ANY DEFECT IN THE PRODUCT, DAMAGES BASED ON INCONVENIENCE,
LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS
RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF THE CUSTOMER HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. SÉURA WILL NOT BE LIABLE FOR ANY LOSS, DAMAGE
OR LIABILITY OR ANY DIRECT, INCIDENTAL, INDIRECT, PUNITIVE, SPECIAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OR MISUSE OF A PRODUCT, OR ARISING OUT OF ANY
BREACH, BY THE PURCHASER OF A PRODUCT, OF THIS LIMITED WARRANTY. SÉURA SHALL
NOT BE LIABLE FOR ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY. SÉURA
SHALL NOT BE LIABLE FOR ANY VERBAL WARRANTY ASSURANCES MADE BY ANY EMPLOYEE
OR AUTHORIZED DISTRIBUTOR, RESELLER OR INSTALLER THAT CONFLICTS WITH OR
ENHANCES THE WRITTEN WARRANTY HEREIN. SOME STATES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON HOW
LONG AN IMPLIED LIMITED WARRANTY LASTS, SO THE EXCLUSIONS MAY NOT APPLY TO A
PARTICULAR PURCHASER. NOTWITHSTANDING ANYTHING HEREIN TO THE CONTRARY, SÉURA’S
MAXIMUM AGGREGATE LIABILITY RELATED TO ANY WARRANTY CLAIM OR WITH RESPECT TO
A PRODUCT SHALL NOT EXCEED THE THEN CURRENT SÉURA WHOLESALE PRICE OF THE
SPECIFIC PRODUCT FROM WHICH THE CLAIM DERIVES.
NOTICE OF ANY WARRANTY CLAIM MUST BE RECEIVED BY SÉURA, IN WRITING, PRIOR TO
THE EXPIRATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. THE PRODUCT
WARRANTY APPLIES ONLY FOR THE PERIODS SET FORTH ABOVE.
Warranty Procedure. A warranty claimant must contact Séura at 920-857-9069 for a diagnostic.
Please have your Product receipt available. At that time, Séura will provide technical support
over the phone to attempt to x the problem. If unsuccessful, a Séura Representative will
determine if the Product will be serviced onsite, replaced, or returned to Séura’s factory in
Green Bay, Wisconsin for repair. If Séura determines that the Product is not covered under
the warranty or damaged in shipping, Séura will notify and inform the purchaser of service
alternatives that are available on a fee basis.
Toll-Free Technical Support: Please call 1-800-957-3872 to speak with a Séura Technical
Support Representative. Séura Representatives are available Monday-Friday, 8:00am-4:30pm
Central Time.
Onsite Service: If Technical Support determines the problem may be xed onsite, a Séura
service agent will be scheduled within 24 hours to service the unit. A Séura representative
will work with the customer to schedule a convenient time for onsite service. Parts may
be sent to the customer’s location. Onsite service is available in the United States during
normal business hours Monday – Friday, unless other special circumstances exist and special
arrangements are made.
Factory Service: If Technical Support determines the Product must be sent back to Séura’s
factory for repair, the customer must follow return instructions below. Séura will ship the
repaired Product to the authorized reseller, installer or customer’s address. This warranty
does not cover removal or installation costs of Products.
Advanced Replacement: If Technical Support determines the Product must be replaced,
Séura will ship a new Product to the authorized reseller, installer or customer’s address.
The customer must follow return instructions below to send the damaged Product back to
Séura’s factory. Credit card information will be collected before shipment of the replacement
Product. If Séura does not receive the original Product back within thirty (30) days of shipping
the replacement Product, the credit card on le will be charged at full MSRP. This warranty
does not cover removal or installation costs of Products.
Return Instructions: If return is necessary, Séura will issue a return goods authorization
(RGA) number and, if applicable, specic return and shipping instructions. A Product will
only be accepted for warranty claims if returned and shipped to Séura in the Product’s
original packaging materials. If original packaging is not available, please contact Séura to
receive authorized replacement packaging. Packages not bearing the issued returned goods
authorization (RGA) number will not be accepted by Séura and will be returned to sender.
In addition to the Product, the package must include the warranty claimant’s original sales
receipt for the purchase of the Product. All Product returns shall be received by Séura, at 1230
Ontario Road; Green Bay, WI 54311 with freight prepaid by the warranty claimant. Séura shall
not be responsible for, and the warranty claimant assumes and retains all such responsibility,
any damage or loss to or of the Product during shipment to and from Séura as the result of
a warranty claim.
Exclusive Remedy. This Limited Warranty sets forth the exclusive remedies of a warranty
claimant, and the exclusive liabilities and obligations of Séura, with respect to allegations of
a defective Product.
19163121.3
The Bluetooth®word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and
any use of such marks by Séura is under license. Other trademarks and trade names are those of their
respective owners.
LT00003