Seura FS-1 User manual

OUTDOOR TV FLOOR STAND
INSTALLATION GUIDE
Model Number:
FS-1
WARRANTY REGISTRATION
REGISTER FOR
EXTRA BENEFITS
Activate within 30 days of purchase:
seura.com/activate
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20 5
16
"
261
4"
14"14"

2
Prior to the installation of this product, read all
instructions. Keep this manual for future reference.
This product is designed to mount Seura outdoor
televisions and accessories weighing up to 220 lbs.
to a concrete pad or engineered wooden structure.
CAUTION DO NOT EXCEED MAXIMUM LISTED
WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY
DAMAGE MAY OCCUR.
Warnings:
• Safety measures must be practiced at all times
during the assembly of this product. Use proper
safety equipment and tools for the assembly
procedure to prevent personal injury.
• At least two qualied people should perform the
assembly procedure. Proper installation must
be followed as outlined in these installation
instructions. Personal injury and/or property
damage can result from dropping or mishandling
the TV.
• Ensure that there are no missing or defective
parts upon receipt. Never use defective parts.
• This product contains small parts that could be
a choking hazard.
• Any oor surface used to ax the Séura mount
must be of adequate thickness and stability to
support the included anchors.
• Do not use this product for any purpose other
than to mount a VESA compliant TV on a solid
level ground as outlined in this manual.
• When mounted to a wood structure, appropriate
lag screws must be mounted into the supporting
members.
• Make sure there are no water or natural gas lines
underground where the stand is to be located.
Cutting or drilling into a water or gas line may
cause severe property damage or personal injury.
Call your local Digger's Hotline prior to digging.
• Do not install near sources of high heat.
• Do not install on a structure that is prone to
vibration, movement or chance of impact.
Note: The included hardware is for mounting on
concrete or wood joists (wood decking). If you are
uncertain about the nature of your surface, please
consult your hardware or installation professional
for proper mounting.
Safety
Compatible with Séura Outdoor TVs:
Pair with any Séura Outdoor TV 42′′ – 86′′ or any other compatible display not surpassing a maximum weight
limit of 200 lbs. Compatible with VESA mount patterns up to 600×400. CAUTION: Séura TV model UB4-85
paired with most Séura soundbar models will exceed the maximum weight limit.
WARNING: Cancer and Reproductive
Harm: www.p65warnings.ca.gov.

3
Parts and Tools Required (not included)
The following tools may be required depending on your particular installation. They are not included.
P5080T
Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3/8˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket M10 Socket*
2
1
5/16˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5/16˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
1/2”
1/2”
1/2”
1/2”
Level
Stud Sensor
(edge-to-edge stud
nder is recommended)
Tape Measure
7/32″ Drill Bit 5/16” Masonry Drill Bit
Pencil Power Drill Philips #2
Screwdriver
(6mm Allen Wrench
for use with 86”
Ultra Bright TV size)
For Wood Joist Installation For Concrete, Brick and Stone Installation
1/2”
1/2”
1/2”
Socket Wrench
½” Socket
½” Combination
Wrench
1/2”
1/2”

4
Floor Stand
Parts Included
Before using the device, please check the following contents of the box for completeness. Illustrations are
not to scale. If any parts are missing or damaged, contact Séura.
(4) 3/8” x 3” Stainless Steel Concrete
Large Diameter Tapcon Screws
(6) 1/4-20x1/2 Stainless Steel
Security Torx Screws
(6) 1/4-20x1/2 Black Stainless
Steel Hex Head Screws
(4) 5/16”
Stainless Steel
Flat Washers
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20 5
16
"
261
4"
14"14"
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20 5
16
"
261
4"
14"14"
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
205
16
"
261
4"
14"14"
OR

5
Parts Included, Packaged as TW-5
Mounting Plate
(2) Tilt Mount TV
Brackets
261
4"
20 5
16
"11 7
16 "
25mm
1"
55
8
"
7"
115
16"
261
4"
20 5
16
"11 7
16 "
25mm
1"
55
8
"
7"
115
16"
261
4"
20 5
16
"11 7
16 "
25mm
1"
55
8
"
7"
115
16"
Mounting Tools and Hardware
(6) Stainless Steel Lag
Screws 5/16”, 3” long
(6) Plastic Anchors, 3” long
For concrete, brick, and
stone installation only
(6) Stainless Steel Flat
Washers, 5/16”
(4) M6 and (4) M8
Phillips VESA Screws
Included with some
mount models
(1) 4mm Allen
Wrench
Included with
some mount
models
261
4"
20 5
16
"11 7
16 "
25mm
1"
55
8
"
7"
115
16"
(1) T27 Security Torx
Screwdriver
Included with some
mount models
(4) Security Torx
T27 x 1.0 x 16mm
Screws
Included with some
mount models

6
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20 5
16
"
261
4"
14"14"
Features
Floor Stand
Mounting Plate
Fasten to the
oor via 4-6
screws.
Tilt Locking Bolts
Allows for tilt
angle of the TV
adjustment.
Top Leveling
Screws
Allows for leveling
adjustments of the
TV after mounting.
Bottom Locking
Screws
Prevents the
TV from being
removed or
dislodged from the
mounting plate.
Directional
Mounting Arrows
The arrow lets you
know which edge
is up.

7
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20 5
16
"
261
4"
14"14"
Height Adjustment
Use both included
screws to set the
desired height.
Cable Pass Through
Run power and content
cables through the back of
the pole or into the oor.
The power cord included
with Séura’s Full Sun Series
85-inch Outdoor TV (model
UB4-85) does not t inside
of the mount pole. The cord
must run alongside the pole
and will not be neatly tucked
away inside.
Cable Pass Through
Run power and content
cables through the pole and
connect to the TV inputs.
The power cord included
with Séura’s Full Sun Series
85-inch Outdoor TV (model
UB4-85) does not t inside
of the mount pole. The cord
must run alongside the pole
and will not be neatly tucked
away inside.
Security Locking Screw
Tighten this screw to prevent
the swivel plate from being
removed.
Swivel Adjustment
Loosening allows
adjustment of the
swivel +/- 360°. Always
retighten as TV may
swivel in the wind. Do
not continue to spin
beyond 360° because
cords become wrapped
and could disconnect
from the connections.

8
Step 1: Assemble and Prepare Mount
1. Attach mounting plate to oor stand
Using four of the included 1/4-20x1/2 security torx screws or four of the included 1/4-20x1/2 black stainless
steel hex head screws, and four at washers, attach the mounting plate to the oor stand rails as shown.
OR
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
205
16
"
261
4"
14"14"
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
205
16
"
261
4"
14"14"
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
205
16
"
261
4"
14"14"
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
205
16
"
261
4"
14"14"
(4) 1/4-20x1/2 Stainless Steel
Security Torx Screws
(4) 5/16” Stainless Steel Flat
Washers
(4) 1/4-20x1/2 Black Stainless
Steel Hex Head Screws
(4) 5/16” Stainless Steel Flat
Washers

9
2. Adjust oor stand length/TV height
Loosen the screws with the provided T27 Security Torx Screwdriver or 4mm Allen Wrench. Adjust to the
desired height of the stand. Tighten screws.
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
205
16
"
261
4"
14"14"
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
205
16
"
261
4"
14"14"
To adjust the
swivel angle of
the TV, loosen
the two thumb
screws on the
back of the oor
stand. Adjust
to the desired
angle. Tighten
both screws.
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
205
16
"
261
4"
14"14"

10
Installation
IMPORTANT: This product must be mounted to a uniform sub-structure such as poured concrete at least 4”
thick or engineered decking with footings. Patio block, loose deck boards, split concrete or any substrate
under 3” thick poses a hazard of falling. Improper installation risks property damage or severe injury.
Consult a professional for verication and inspection of the installation structure.
IMPORTANT: HANDLE THE TV IN A VERTICAL POSITION TO AVOID DAMAGE TO THE
SCREEN. IF PLACING THE TV SCREEN-SIDE DOWN OR LEANING AGAINST A WALL DURING
INSTALLATION, COVER THE SCREEN WITH A PROTECTIVE CLOTH OR BLANKET.
Step 2: Attach Floor Stand Mounting Plate to Floor
1. Choose mounting location
Place the oor stand in the desired location.
Wood Joist Mounting:
At least four lag screws must be fastened to
the joists or appropriate structural member. All
six screws are recommended. Use a pencil to
mark the locations of the screws.
Concrete:
Use the included four concrete large diameter
Tapcon screws. Mark all hole locations in the
mounting plate slots with a pencil on the oor.

11
2. Drill pilot holes
Wood Joist Mounting:
Pre-drill the marked holes on the oor 3-inches
deep with a 7/32” drill bit.
Concrete:
Pre-drill the four marked holes on the oor at
least 4-inches deep with a 5/16” masonry drill bit.
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20 5
16
"
261
4"
14"14"

12
3. Attach oor mounting plate
Align the mounting plate with the pre-drilled holes. Ensure that the cable pass through holes on the
mount are positioned appropriately.
Wood Joist Mounting:
Attach mounting plate to the oor using the six lag
screws and six at washers. Do not over tighten
the lag screws. Tighten the lag screws only until
the washers are pulled rmly against the mounting
plate.
Concrete:
Make sure the anchor is seated completely ush
with the mounting plate even if there is another
layer of material such as tiles, ooring, or pavers.
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20 5
16
"
261
4"
14"14"
For wood joist
installation, use
included lag screws.
For concrete
installation, use
included Tapcon
type screws.

13
Step 3: Attach Tilt Mount TV Brackets to TV
IMPORTANT: Check your TV manual before attaching mount brackets
to TV. Some models require attaching soundbar brackets in tandem
with attaching mount brackets.
Using a Philips #2 Screwdriver (or 6 mm Allen Wrench for 86” Ultra
Bright TV), remove the four VESA mount screws from the back of
the TV. Place the two identical Tilt Mount TV Brackets at against
the back of the TV with the arrows pointed towards the top of the
TV. Line the brackets up with the VESA mount fastener locations. If
mounting a Séura Outdoor TV (49-inch to 86-inch display sizes), use
the second hole down from the top on each Tilt Mount TV Bracket. If
mounting a Séura Outdoor TV model SHD2-43, then use the top hole
on each Tilt Mount TV Bracket. Attach the Tilt Mount TV Brackets to
the TV using the same four VESA mount screws that you just removed.
261
4"
20 5
16
"11 7
16 "
25mm
1"
55
8
"
7"
115
16"
Note: If installing with a soundbar
or if the TV’s VESA screws are
not long enough to attach the Tilt
Mount TV Brackets, then use the
four included Security Torx T27
x 1.0 x 16mm Screws or the four
included M6 or M8 Philips VESA
screws that are slightly longer than
the TV’s factory screws.
Shade Series
TV 55″ 65″ 75″
Screw Size M6 M6 M8
Full Sun Series
TV 50″ 65″ 85″
Screw Size M8 M8 M8
Note: Security Torx Screws (available with some mount
models) provide additional security to attach the brackets
to the TV. Installers may opt to use these in place of the
TV’s VESA screws, even if longer screws are not needed to
accommodate a soundbar bracket or mount brackets.

14
Step 4: Hang the TV and Connect Power and Content Cables
IMPORTANT: NEVER TRY TO HANG A TV BY YOURSELF. ALWAYS USE AT LEAST TWO PEOPLE TO LIFT THE TV
INTO PLACE.
1. Lift the TV and bring the back of the TV towards
the mount, positioning it slightly above the
mounting plate.
2. Lower the TV to hook the bottom hooks of the
Tilt Mount TV Brackets on the lower rail of the
mounting plate.
3. Bring the top of the TV closer to the mount to
hook the top hooks of the Tilt Mount TV Brackets
on the top rail of the mounting plate.
4. Make sure the bottom and top rails are fully
engaged.
Do not let go of the TV until you are certain that the
top and bottom hooks of both mounting brackets
are securely engaged on the upper and lower
mounting rails of the mounting plate.
5. Connect power and make connections to TV
inputs. Cords can be routed through the oor
stand pole so they are out of sight. The power
cord included with Séura’s Full Sun Series 85-inch
Outdoor TV (model UB4-85) does not t inside of
the mount pole. The cord must run alongside the
pole and will not be neatly tucked away inside.

15
Top Leveling Screw
Allows for leveling
adjustments of the TV
after mounting.
Bottom Locking Screw
Prevents the TV from
being removed or
dislodged from the
mounting plate.
Step 5: Adjust the TV
Séura recommends checking knobs, screws, and bolts
every two to six months. Temperature uctuations,
wind, and normal wear and tear can loosen hardware
over time.
Top leveling screw adjustment:
If your TV is not level, the two (2) top leveling screws
located on the top of the tilt mount TV brackets will
allow you to compensate for this tilt by adjusting
the screws with the provided T27 security torx
screwdriver or 4mm Allen wrench.
1. Loosen both leveling screws (one on each bracket).
2. Adjust the tilt of your TV.
3. Tighten both leveling screws.
Do not overtighten the leveling screws.
Bottom locking screw adjustment:
After you have adjusted leveling the TV, tighten the
two (2) bottom locking screws located on the bottom
of the tilt mount TV brackets (one on each bracket)
using the provided T27 security torx screwdriver or
4mm Allen wrench.
Do not overtighten the locking screws.
261
4"
20 5
16
"11 7
16 "
25mm
1"
55
8
"
7"
115
16"
Caution: It is possible to dislodge
your TV while you level it. Use
extreme caution until you tighten the
leveling and locking screws.

16
Tilt adjustment:
Adjusting the TV Tilt Angle
1. Place one hand on the center-top edge
of the TV.
2. Place the other hand on the center-
bottom edge of the TV.
3. Using the upper hand, gently pull the top
of the TV towards you while the lower
hand gently pushes the bottom of the TV
away from you.
Adjusting the TV to the Original Position
1. Place one hand on the center-top edge
of the TV.
2. Place the other hand on the center-
bottom edge of the TV.
3. Using the upper hand, gently push the top
of the TV towards the wall while the lower
hand gently pulls the bottom of the TV
away from the wall.
After tilt is adjusted to the desired position,
tighten the (2) tilt locking bolts on each
bracket until the brackets are rmly secured.
Do not overtighten the tilt locking bolts.
Tilt
Locking
Bolts

17
Specications
FLOOR STAND
Model: FS-1
GENERAL
DISPLAY COMPATIBILITY 42" - 86" Séura Outdoor TVs*
VESA COMPATIBILITY Compatible with VESA mount patterns up to 600×400
CUSTOMIZABLE VIEWING
Swivel 360° / - 360°
Extend from 28.5" to 43" (in 2" increments) from
installation surface
FLOOR STAND DIMENSIONS Collapsed: 26.25" w x 14" d x 39.75" h
Extended: 26.25" w x 14" d x 61.75" h
MOUNTING PLATE DIMENSIONS 14” w x 14” d
FINISH COLOR Black Powder Coat
DURABILITY Acrylic E-Coated Steel
INSTALLATION
MAXIMUM WEIGHT LIMIT 200 lbs
INSTALLATION SURFACE Concrete at least 4" thick or concrete backed ooring, tile, brick
pavers, and fully framed wood structures with proper footings
HARDWARE Stainless Steel
SHIPPING
SHIPPING CONTAINER DIMS 16.5" w x 16.25" d x 41.5" h
SHIPPING WEIGHT 56 lbs
PRODUCT WEIGHT 47 lbs
Maximum Weight Limit: 200 lbs.
The wall structure must be capable of supporting at least ve times the weight of the TV. If not, the wall
structure must be reinforced.
* The power cord included with Séura’s Full Sun Series 85-inch Outdoor TV (model UB4-85) does not t
inside of the oor stand pole. The cord must run alongside the pole and will not be neatly tucked away.

18
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20 5
16
"
261
4"
14"
14"
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20 5
16
"
261
4"
14"
14"

94-060600
Publish date: December 5, 2022
Information is subject to change without notice.
© 2022 Séura
1230 Ontario Road Green Bay, Wisconsin 54311
1-800-957-3872 [e-mail]
www.seura.com
LIMITED PRODUCT WARRANTY
For information regarding Séura’s warranty policy, please visit our website: www.seura.com/warranty. If
the current Séura warranty policy is after your product purchase date, please contact Séura Customer
Support to request warranty documentation from the date of your purchase.
For additional customer support, please contact Séura.
Toll Free: 1-800-957-3872 (Monday - Friday 8:00 am – 4:30 pm, Central Time)
Website: www.seura.com/support