SHADE SCAPES AMERICAS SPECTRA User manual

1:
(a) Determine the location where you want to install the
Rotational In-Ground Fitting (IS). Dig a 24" x 24" square hole with
a depth of 16". The edges of the hole should vertical. Sloping,
rounded sides will allow the concrete to loosen over time.
A COMPONENTS LIST & REQUIRED TOOLS
1X IN-GROUND FITTING (IR)
Box A
B MOUNTING INSTRUCTIONS
REQUIRED TOOLS LIST (not included):
Standard Spade/Shovel
Carpenter's Level
Pre-Mixed "High Early Strength" Concrete
Iron Rebar
Small Sledge Hammer
Duct Tape
Wheelbarrow
Hoe
4X#10x20mm#SPIGOT#BOLTS#(A2)*##################################################################################################
1X#6mm#ALLEN#WRENCH#(T2)*###########
*PLEASE NOTE THE SPIGOT BOLTS AND 6mm ALLEN WRENCH ARE LOCATED IN THE IN-GROUND FITTING MOUNT BOX,
BUT WILL NOT BE USED UNTIL YOU BEGIN TO INSTALL THE UMBRELLA. SEE YOUR UMBRELLA OWNERS MANUAL FOR DETAILS.
IN-GROUND FITTING
INSTALLATION MANUAL
IN-GROUND FITTING:
SPECTRA, ECLIPSE, ICARUS, Infina
for ROTATIONAL SPIGOT (and Infina)
NOTE: The dimensions given above are a general guideline for
the size of the hole. A general rule of thumb: the easier the
ground is to dig, the bigger the hole should be, or alternately,
if the ground is hard the hole can be smaller.
1
Once installed, always use COMMON SENSE WIND GUIDELINES: If it is too windy to be outside enjoying the day, it is best to lower/collapse
the Umbrella Frame w/ Fabric Canopy. It is also important to keep it lowered/collapsed when unattended. See manufacturer's limited warranty
on page 2.
Please thoroughly read this installation manual before installing the Spectra Mount System, and before assembling and operating the Spectra
Round Umbrella. The Spectra Warranty does not cover damage caused by incorrect installation, wind, or wrongful use of the product. All users
must be properly trained in operation and wind guidelines.
1X - ROTATIONAL
SPIGOT ASSEMBLY (SR)
(Packed with Umbrella Structure)

SPIGF=SSA2015.01
C WARRANTY
Umbrosa NV warrants to the consumer that Spectra/Eclipse/Icarus products are free from manufacturer defects in material or workmanship for
a period of three (3) years from the date of original purchase when used in compliance with directions as outlined in the manufacturer’s
instructions, which includes reasonable and necessary maintenance by the consumer. Warranty does not include normal wear and tear of
product. Umbrosa takes no responsibility for incorrect use or assembly related to installation area, consistency of supports and relative
hardware used, and capacity of mounting surfaces. Failure to follow the given assembly, maintenance, use and care instructions will void the
product warranty. In case of manufacturing defects in material or workmanship, Umbrosa NV, agrees to, at their discretion, send the
replacement part for all defective parts.
Distributed#by#ShadeScapes#Americas#www.shadescapesamericas.com;#817.217.4446.##For#assembly#assistance#or#questions#please#
contact#ShadeScapes#Americas#at#970.527.7070,#or#email#[email protected]
5:
(a) Mix the concrete in a wheelbarrow following the instructions
on the packaging of the Concrete Mix.
(b) Fill the hole with concrete and stop when the concrete
is 4" from the bottom of the round plate of the Spectra
In-Ground Fitting (IR).
(c) Replace a layer soil before replacing the sod if mounted in
a grassy area.
2
NOTE: If not mounting in a grassy area, the concrete may be
poured until level with the top plate of the In-Ground Fitting .
3:
The top plate of the In-Ground Fitting has four (4) tapped
holes. Two (2) of the tapped holes should be aligned SQUARE
to whatever you are aligning the Spectra Round Umbrella with.
For example, your house, edge of patio, etc., as shown in the
diagram to the left.
4:
(a) Stick the piece of Iron Rebar connected to the Spectra
In-Ground Fitting (IR) into the ground near the center of
the hole.
(b) Align the tapped holes by rotating as necessary. See
alignment instructions in step B3.
(c) With a carpenter's level or straight edge, make sure
the top plate is flush with the subsoil.
(d) Ensure the top plate is level by placing the Carpenters
Level in two directions 90° to each other. Continue to make
adjustments until the plate is perfectly level.
2:
(a) Hammer several lengths of Iron Rebar into the sides
of the hole at varying angles around the hole. There should be
a minimum of one length pointing in each wind direction. This
process anchors the concrete to the subsoil and prevents it
from becoming loose in the hole over time.
(b) Prepare to install the Rotational In-Ground Fitting (IR) by
attaching a length of Iron Rebar to the tube of the In-Ground
Fitting with duct tape. IMPORTANT: Tape both sides of the
tapped holes to prevent concrete from getting in the threads.