SHADE SCAPES AMERICAS PARAFLEX PAVER BASE W/OPTIONAL COVER User manual

1X PAVER BASE (P1)
Box A
1X - PARAFLEX SPIGOT (S1)
Box B
1X PAVER BASE COVER (P2) optional
Box C
REQUIRED TOOLS LIST (not included):
8X 16"x16"x2" CONCRETE PAVERS
NOTE: Paver sizes vary from location to location.
15-3/4" to 15-7/8" square are acceptable .
1
PAVER BASE W/OPTIONAL COVER
INSTALLATION MANUAL
4X - 10x20mm SPIGOT BOLTS (A2)
1X - 6mm ALLEN WRENCH (T2)
Box A
Please thoroughly read this installation manual before installing the Paraflex Mount System, and before assembling and operating the
Paraflex Umbrella. The Paraflex Warranty does not cover damage caused by incorrect installation, wind, or wrongful use of the
product. All users must be properly trained in operation and wind guidelines.
Once installed, always use COMMON SENSE WIND GUIDELINES: If it is too windy to be outside enjoying the day, it is best to
lower/collapse the Umbrella Frame w/ Fabric Canopy. It is also important to keep it lowered/collapsed when unattended. See
manufacturer's limited warranty on page 2.
A COMPONENTS LIST & REQUIRED TOOLS

!"!#$%%&'()*'(
The manufacturer warrants to the consumer that the Paver Base w/Optional Cover is free from manufacturer defects in material or workmanship for a period of
three (3) years from the date of original purchase when used in compliance with directions as outlined in the manufacturer’s instructions, which includes
reasonable and necessary maintenance by the consumer. Warranty does not include normal wear and tear of product. Manufacturer takes no responsibility for
incorrect use or assembly related to installation area, consistency of supports and relative hardware used, and capacity of mounting surfaces. Failure to follow
the given assembly, maintenance, use and care instructions will void the product warranty. In case of manufacturing defects in material or workmanship,
manufacturer agrees to, at their discretion, send the replacement part for all defective parts.
+,-./,01.234054%6732-8792-4:;2/,87-444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444444
<<<*-6732-8792-7;2/,87-*8=;>4???*&(@*AAAB4444444
C=/47--2;0D547--,-.7E824=/4F12-.,=E-49D27-248=E.78.4%6732%8792-4:;2/,87-47.44???*&(@*AAABG4=/42;7,D4-199=/.H-6732-8792-1-7*8=;*44
2
3:
(a) If you purchased the optional Paver Base Cover (P2),
place it over the Paver Base (P1) and push it down until it
touches the ground.
4:
(a) Place the Paraflex Spigot (S1) on top of the optional Paver Base
Cover, or on top of the assembled Paver Base pieces (P1).
(b) Align the countersunk holes of the Paraflex Spigot with the
tapped holes in the Paver Base Pieces (P1).
(c) Insert the four (4) Spigot Bolts (A2) into the countersunk
holes, and using the 6mm Allen Wrench (T2), tighten to fully secure
the Paraflex Spigot.
2:
(a) Place the 8X 16"x16"x2" Concrete Pavers (not included) in the
four quadrants of the Paver Base (P1), by stacking two (2) in each
quadrant.
B MOUNTING INSTRUCTIONS
1:
(a) Remove the two Paver Base (P1) pieces from Box A.
(b) Join the two sections by fitting them together at the
notched section in the middle of each piece as shown at
right.