Shinko SE series User manual

PLUG-IN TYPE
PROGRAMMABLE SIGNAL CONDITIONER
SE SERIES
INSTRUCTION MANUAL

2
Preface
Thank you for purchasing the SE series Programmable Signal Conditioner.
This manual contains instructions for the mounting, functions, operations and notes when
operating the SE series. To prevent accidents arising from the misuse of this instrument, please
ensure the operator receives this manual.
Notes
• This instrument should be used in accordance with the specifications described in the manual.
If it is not used according to the specifications, it may malfunction or cause a fire.
• Be sure to follow the warnings, cautions and notices. If they are not observed, serious injury or
malfunction may occur.
• Specifications of the SE series and the contents of this instruction manual are subject to change
without notice.
• Care has been taken to assure that the contents of this instruction manual are correct, but if there
are any doubts, mistakes or questions, please inform our sales department.
• This instrument is designed to be installed on a DIN rail within a control panel. If it is not, measures
must be taken to ensure that the operator does not touch power terminals or other high voltage
sections.
• Any unauthorized transfer or copying of this document, in part or in whole, is prohibited.
• Shinko Technos CO., LTD. is not liable for any damages or secondary damages incurred as a
result of using this product, including any indirect damages.
SAFETY PRECAUTIONS (Be sure to read these precautions before using our products.)
The safety precautions are classified into categories: “Warning” and “Caution”.
Depending on the circumstances, procedures indicated by Caution may cause serious
results, so be sure to follow the directions for usage.
Warning
Warning
• To prevent an electric shock or fire, only Shinko or other qualified service personnel may
handle the inner assembly.
• To prevent an electric shock, fire or damage to the instrument, parts replacement may only
be undertaken by Shinko or other qualified service personnel.
Safety precautions
• To ensure safe and correct use, thoroughly read and understand this manual before using this
instrument.
• This instrument is intended to be used for industrial machinery, machine tools and measuring
equipment. Verify correct usage after consulting purpose of use with our agency or main office.
(Never use this instrument for medical purposes with which human lives are involved.)
• External protection devices such as protective equipment against excessive temperature rise, etc.
must be installed, as malfunction of this product could result in serious damage to the system or
injury to personnel. Also proper periodic maintenance is required.
• This instrument must be used under the conditions and environment described in this manual.
Shinko Technos Co., Ltd. does not accept liability for any injury, loss of life or damage occurring
due to the instrument being used under conditions not otherwise stated in this manual.
Caution with respect to Export Trade Control Ordinance
To avoid this instrument from being used as a component in, or as being utilized in the
manufacture of weapons of mass destruction (i.e. military applications, military equipment,
etc.), please investigate the end users and the final use of this instrument.
In the case of resale, ensure that this instrument is not illegally exported.
Caution
Procedures which may lead to dangerous conditions and cause
death or serious injury, if not carried out properly.
Procedures which may lead to dangerous conditions and cause
superficial to medium injury or physical damage or may degrade or
damage the product, if not carried out properly.

3
1
1. .I In ns st ta al ll la at ti io on np pr re ec ca au ut ti io on ns s
Caution
This instrument is intended to be used under the following environmental conditions
(IEC61010-1): Overvoltage category , Pollution degree 2
Ensure the mounting location corresponds to the following conditions:
• A minimum of dust, and an absence of corrosive gases
• No flammable, explosive gases
• No mechanical vibrations or shocks
• No exposure to direct sunlight, an ambient temperature of -5 to 55 (23 to 131 )
that does not change rapidly, and no icing
• An ambient non-condensing humidity of 35 to 85%RH
• No large capacity electromagnetic switches or cables through which large current is flowing
• No water, oil or chemicals or where the vapors of these substances can come into
direct contact with the unit
• When installing this unit within a control panel, take note that the ambient temperature
of this unit as well as the control panel must not exceed 55 (131 ). Otherwise the life
of electronic components (especially electrolytic capacitors) may be shortened.
Note: Avoid setting this instrument directly on or near flammable material even
though the case of this instrument is made of flame-resistant resin.
2
2. .W Wi ir ri in ng gp pr re ec ca au ut ti io on ns s
Caution
• Do not leave wire remnants in the instrument, because they could cause a fire and/or a
malfunction.
• When wiring terminals, use a solderless terminal with an insulation sleeve in which an
M3 screw fits.
• Tighten the terminal screw within the specified torque.
If excessive force is applied to the screw when tightening, the screw may be damaged.
• This instrument has no built-in power switch, circuit breaker or fuse. It is necessary to
install them near the instrument.
(Recommended fuse: Time-lag fuse, rated voltage 250V AC, rated current 2A)
• For wiring of AC power source, be sure to use exclusive terminals as described in this
manual. If AC power source is connected to incorrect terminals, the unit will burn out.
• For a 24V DC power source, do not confuse polarity.
• Do not apply a commercial power source to the sensor connected to the input terminal nor
allow the power source to come into contact with the sensor, as the input circuit may burn out.
• Use a thermocouple, compensating lead wire and 3-wire system RTD according to the
sensor input specifications of this unit.
• When using DC voltage and current input, do not confuse polarity when wiring.
• Keep the input/output wires and power line separate.
3
3. .O Op pe er ra at ti io on na an nd dm ma ai in nt te en na an nc ce ep pr re ec ca au ut ti io on ns s
Caution
• Do not touch live terminals. This may cause electric shock or problems in operation.
• Turn the power supply to the instrument OFF when retightening the terminal and
cleaning. Working on or touching the terminal with the power switched ON may result
in severe injury or death due to Electric Shock.
• Use a soft, dry cloth when cleaning the instrument.
(Alcohol based substances may tarnish or deface the unit.)
• As the display section is vulnerable, do not strike or scratch it with a hard object or
press hard on it.

4
Model explanation
Indication Model
SE2 SE2U, SE2E, SE2R, SE2A, SE2V, SE2P
SE1 SE1U, SE1E, SE1R, SE1A, SE1V, SE1P, SE1D, SE1D-F
SE series
SEW SEWU, SEWD
Characters used in this manual
Indication
Number, / -1 0 1 2 3 4 5 6 7 8 9
Indication
Alphabet A B C D E F G H I J K L M
Indication
Alphabet N O P Q R S T U V W X Y Z
means that no character is indicated (unlit) on the display.

5
--- CONTENTS ---
1. Model Page
1.1 Model ---------------------------------------------------------------------------- 6
1.2 How to read the model label ----------------------------------------------- 6
2. Name and functions of sections -------------------------------------------- 7
3. Mounting
3.1 External dimensions (Scale: mm) ----------------------------------------- 8
3.2 Mounting to a DIN rail -------------------------------------------------------- 8
3.3 Removal from a DIN rail --------------------------------------------------- 10
4. Wiring
4.1 Lead wire solderless terminal -------------------------------------------- 12
4.2 Terminal arrangement, circuit configuration -------------------------- 13
4.3 Wiring of terminals
4.3.1 Power source wiring ---------------------------------------------------- 16
4.3.2 Output wiring ------------------------------------------------------------- 16
4.3.3 Input wiring --------------------------------------------------------------- 17
5. Operation flowchart ------------------------------------------------------------ 18
6. Setup
6.1 Indication after power-on -------------------------------------------------- 21
6.2 Basic operation of setup --------------------------------------------------- 22
6.3 Setup of the unit
6.3.1 Function group ---------------------------------------------------------- 24
6.3.2 CH2 function group ----------------------------------------------------- 27
6.3.3 Special function group ------------------------------------------------- 27
6.3.4 Using this unit as a standard signal converter ------------------ 28
6.3.5 Using the Reverse function ------------------------------------------ 28
6.3.6 Using the first order lag filter function ----------------------------- 28
7. Adjustment
7.1 Basic operation of adjustment ------------------------------------------- 29
7.2 Adjustment
7.2.1 Output adjustment group --------------------------------------------- 30
7.2.2 CH2 output adjustment group --------------------------------------- 31
8. Operation
8.1 Indication after power-on -------------------------------------------------- 32
8.2 Unit operation ---------------------------------------------------------------- 34
9. Specifications ------------------------------------------------------------------- 35
10. Troubleshooting
10.1 Indication -------------------------------------------------------------------- 38
10.2 Key operation -------------------------------------------------------------- 38
10.3 Operation -------------------------------------------------------------------- 39
11. Character table ----------------------------------------------------------------- 39