Shinn Fu Pro-Lift I-4039 User manual

Model
I-4039
Car Fan
90 DAYS LIMITED WARRANTY
For a period of ninety (90) days from date of purchase,
Shinn Fu Co. of America, Inc. will repair or replace, at its option,
without charge, any of its products which fails due to a defect in
material or workmanship, or which fails to conform to any implied
warranty not excluded hereby.
Except where such limitations and exclusions are
specically prohibited by applicable law, (1) the CONSUMER’S
SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR
REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED
ABOVE, and (2) Shinn Fu Co. of America, Inc. SHALL NOT
BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGE OR LOSS WHATSOEVER, and (3) THE DURATION
OF ANY AND ALL EXPRESSED AND IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION, ANY WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, IS LIMITED TO A PERIOD OF NINETY (90) DAYS
FROM DATE OF PURCHASE.
Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply
to you. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specic
legal rights, and you may also have other rights which vary from
state to state.
4
12 Volt
D.C.
Shinn Fu Company of America, Inc. ©
2003
10939 N. Pomona Ave.
Kansas City, MO 64153
Phone: [phone]
Fax: [phone]
Printed in China
I-4039-M0_042014

INSTALLATION
1. Locate a suitable place to install the fan, for example, on the
dashboard or doorpost. Be sure the fan can oscillate freely.
2. Using the fan’s bracket plate as a template, drill two 1/8” holes
in the mounting location and install the bracket plate with two
provided self tapping screws.
3. Secure the bracket to the bracket plate with screw attached.
4. Attach the switch box to a metal (non-ammable) surface.
OPERATION
1. Oscillation Lever: The fan oscillates if this lever is pulled down.
To stop oscillation, push the lever back up.
2. Variable Shift Head Oscillation Mechanism: To reset the angle
of the fan, turn the head to desired position. Oscillation will
then continue at the new angle.
3. Tilt Adjustment Screws: To change the degree of upward or
downward tilt of the fan, loosen the screws and set the head
to the desired angle, then re-tighten the screws.
4. Power Switch: To turn the power on, push the switch on the
switch box to FAST for high speed, SLOW for low speed.
MAINTENANCE
Periodically inspect the Car Fan for cracked or worn wiring.
Ensure that all parts move freely. Clean the fan with a wet rag.
Do not use gasoline, benzine, thinners or other volatile solvents.
Lubrication is not necessary, as a special oil-less metal is used.
2 3
! SAFETY MESSAGE !
No alteration shall be made to this device. Only attachments
and / or adapters supplied by the manufacturer shall be used.
• Leer, comprender, y seguir las instrucciónes antes de utilizar
el aparato.
• El manual de instrucciónes y la información de seguridad
deben estar comunicado en lengua del operador antes del
uso.
• No seguir estas indicaciónes puede causar daños
personales o materiales.
ADVERTENCIA
!
oscillation lever
tilt adjustment screw
bracket bracket plate
Study, understand, and follow all instructions provided with
and on this device before use. Only plug into a 12V cigarette
lighter receptacle. Switch box gets very hot when in use. Do
not attach to ammable material. Do not block air vents. Only
use fuse recommended by the vehicle owner’s manual. Do not
position the power cord where it may become damaged. Keep
out of the reach of children. Failure to heed these markings
may result in personal injury and / or property damage.
!WARNING