Shinybow USA SB-5688CT User manual

In st ru ction Manual
Part No.: ENCL005688CT0A0
Thank you for purchasing the SB-5688CT HDMI-CAT6 Matrix Switcher. You will find this unit easy to
install and highly reliable but it is essential that you read this manual throughly before attempting to
use 8x8 HDMI-CAT6 Matrix switcher.
HDMI-CAT6 MATRIX SWITCHER SERIES
8x8 HDMI-CAT6 MATRIX SWITCHER
MODEL : SB-5688CT
M U LT I M E D I A A U D I O A N D V I S U A L
HDBaseT

SAFETY INFORMATION
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL
1. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original
factory packing.
2. Read all documentation before operating your equipment. Retain all documentation for future reference.
3. Follow all instructions printed on unit chassis for proper operation.
4. Do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
5. Make sure power outlets conform to the power requirements listed on the back of the unit.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on
or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit
7. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of
a piece of equipment is not defeated.
8. Mains voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by
any warranty.
9. Power down & disconnect unit from mains voltage before making connections.
10. Never hold a power switch in the ＂ON＂ position.
11. Do not use the unit near stoves, heat registers, radiators, or other heat Producing devices.
12. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit,
13.
such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be
Periodically ＂blown free＂ of foreign matter.
14.
Do not remove the cover. Removing the cover will expose you to potentially dangerous voltages. There are no user serviceable parts inside.
15.
Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
16.
Non-use periods. The power cord of equipment should be unplugged from the outlet when left unused for a long period of time.
Service Information Equipment should be serviced by qualifier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
from the appliance.
IMPORTANT SAFETY INSTRUCTIONS
To insure the best from this product, please read this manual carefully. Keep it in a safe place for future reference.
To reduce the risk of electric shock, do not remove the cover from the unit. No user serviceable parts inside. Refer servicing to qualified personnel.
To reduce the risk of fire, do not expose the unit to rain, water or excessive moisture.
Do not force switched or external connections.
When moving the unit disconnect the serial port connections first then the power cable and finally the interconnecting cables to other devices.
Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Use a clean dry cloth.
Installation of this unit should be in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold.
This symbol is intended to alert the user to the presence of uninsulated
enclosure tha may be of sufficientmagnitude to constitue a risk of
electric shock to persons.
This symbol is intended to alert the user to the presence of important
operational and maintenance (serving) instructions in the literature
accompanying the appliance.
T prevent electric shock do not use this (polarised) plug with an o
extension cord, receptacle or other outlet unless the blades can
be fully inserted to prevent blade exposure.
T prevent electric shock, match wide blade of plug to wide slot, o
fully insert.
Caution:
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK),
NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED SERVICE PERSONAL.
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
T
I
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. .
DO NOT OPEN
of uninsulated “dangerous voltage” within the products enclosure that
RISK OF ELECTRIC SHOCK

PAGE 3SB-5688CT INSTRUCTION & OPERATION MANUAL
TABLE OF CONTENTS
TABLE OF CONTENTS
INTRODUCTION AND PACKAGE CONTENTS
FEATURES
SPECIFICATION
FRONT PANEL - 1
FRONT PANEL - 2
FRONT PANEL - 3
REAR PANEL - 1
REAR PANEL - 2
EDID FUNCTION 1 - EDID
EDID FUNCTION 2 - EMBEDDED EDID
EDID FUNCTION 3 - LEARNING
EDID FUNCTION 4 - LEARNING EDID
EDID FUNCTION 5 - EDID SETUP
TYPICAL APPLICATION - Sample to control projector via HDBaseT
TYPICAL APPLICATION - Sample for Switcher control IN/OUT
IR REMOTE CONTROL
IR REMOTE CONTROL - IR DATA CODE
REMOTE CONTROL - ROOM 1~4
REMOTE CONTEOL - ROOM 5~8
CEC Control
IR EXTERNAL INSTALL
RS232 Control
TYPICAL APPLICATION - Sample to Remote Satellite Receiver
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________

INTRODUCTION AND PACKAGE CONTENTS
PAGE 4 SB-5688CT INSTRUCTION & OPERATION MANUAL
PACKAGE CONTENTS
INTRODUCTION
1. SB-5688CT Matrix Switcher
2. Operating Instructions
3. RS-232 V2.0 Protocol Instructions
4. Master wireless IR Remote Control (SW-5688)
5. 8 each; Individual wireless IR Control (SW-5688CT-IR01~IR08)
6. 19 inch Ear mount bracket (Part # 2U-440L)
7. IR Extender Transmitter (SB-101)
8. IR Extender Receiver (SB-100)
9. 2 each; IR Extender Cable 10 feet (3M)
10. CD Contents : This manual, Windows GUI, ISP V1.0 Windows driver
11. RS232 Cable 6 feet (2M)
12. Worldwide Universal Power Supply 100~230 VAC, AC 50/60Hz, 10A
The SB-5688LCM-CT is high-performance 8x8 matrix routing switcher with eight (8) HDMI inputs
and supports simultaneously eight (8) HDMI and eight (8) CAT5e/6/7 outputs. The SB-5688LCM-CT
works with products designed using HDBaseT specifications. Supporting HDMI Video with
embedded audio, RS-232, IR bi-directional, and all over a single CAT5e/6/7 cable. With a signal
bandwidth of 340Mhz, there is no signal degradation. High Definition Digital signals can be selected
and distributed to any 16 outputs simultaneously. The Switcher is certified as being fully CEC and
HDCP 2.0 compliant, HDMI V1.4a 3D formats, data rates up to 6.75 Gbps. Supports
UXGA/WUXGA/DVI 1920x1200 resolution to any HD displays. The SB-5688LCM-CT has one (1)
CAT5e/CAT6 and HDMI connector for each output, effectively making this an 8x16 switcher (same
signal on both outputs). One (1) CAT RJ-45 connection on each output extends the HDMI signal to
remote location via HDBaseT CAT5e/6/7 HDMI Receiver SB-6335R. The EDID can be selected
between seven (7) different modes. Control is provided via Front panel push buttons, IR remote or
via RS-232. An RS-232 Windows GUI interface is provided for matrix routing.
Member of the HDBaseT Alliance
Products support HDBaseT Specifications

FEATURES
PAGE 5SB-5688CT INSTRUCTION & OPERATION MANUAL
1. 8x HDMI source devices matrix switched to 8x HDMI and 8x CAT Extender output devices.
3. HDMI digital Video w/embedded Audio, DVI format and CEC/HDCP 2.0 compliant
4. Worldwide control EDID modes for HD Video resolutions.
5. Link speeds of up to 6.75 Gbps (link clock rate of 340MbHz), Support HDMI 1.4a 3D formats.
6. Wide range of HD resolutions from PC XGA to WUXGA 1920x1200 and
HDTV/DTV HDMI resolutions 480i/480p, 576i/576p, 720p, 1080i & 1080p
7. Compatible with all HDMI source devices, PC monitors, Plasma HD display, HDTV
and audio receivers/amplifiers.
8. Digital Video TMDS formats Resolution up to 1080P-60 with Deep color 36-bit.
9. Digital Audio Support : - Dolby TrueHD,
- Dolby Digital,
- Dolby Digital Plug/ex,
- DTS,
- DTS-HD,
- DTS-HD Master,
- DTS-EX
- PCM, PCM2, LPCM2..
10. Various User Interface control:
‧Windows based GUI control via RS232 port
‧Front Panel push button
‧IR wireless remote control
‧Third party RS232 controller (via simple ASCII)
11. Support world wide control functions: ALL/OFF/RECALL/ENTER/MEMORY/EDID/LOCK
12. Support EDID modes :
Internal modes : AUTO/1080P-2CH/1080P-5.1/1080P-7.1/1080i-2CH/720P-2CH
External modes : Passing mode with learning function.
13. Automatic scanning input & output status via LED show on front panel.
14. Support IR Remote and IR Extender with distance up to ~ 1000' (300M) Maximum.
15. EDID configuration via Internal modes.
16. Consumer Electronic Control (CEC) switch all open or OFF
The Switcher will remember that last state during a power cycle.
When power is removed and resorted, the last configuration will be invoked.
5e/6/7
FEATURES
The SB-5688LCM-CT works with products designed using HDBaseT specifications. Supporting
HDMI Video with embedded audio, RS-232, IR bi-directional, and all over a single CAT5e/6/7
cable.
2. Application IR enabled by products designed using HDBaseT Specifications, RS-232, Multi Audio
Format and HD Video Signals over CAT5e/6 Cable

SPECIFICATIONS
SPECIFICATIONS
As product improvement is continuous, specifications are subject to change and without notice or liability.
PAGE 6 SB-5688CT INSTRUCTION & OPERATION MANUAL
Type of HDMI Switcher 8x HDMI inputs To 8x HDMI and 8x CAT5e/6/7 Outputs Matrix Switcher
HDMI Support HD 1080P-@60Hz, H36-bit Deep color, 3D of HDMI V1.4a formats.
HDCP / CEC Support HDCP 2.0 Compliant, CEC Compliant.
Video Bandwidth Double Data Rates: 340Mhz, Total 6.75Gbps bandwidth.
Digital Video Support HD:480i/ 480p/ 720p/ 1080i/ 1080p up to 36bit deep color
Digital Audio Support Multi Audio Formats 5.1 / 7.1, MAT(MLP)
Dolby Digital,
Dolby TrueHD,
Dolby Digital Plus,
DTS, DTS-ES 6CH,
DTS-HD, DTS-HD-HRA, DTS-HD Master,
(PCM-2CH)
Controls IR Remote Controller (remote switcher)
8x IR Room Remote Controller
IR External port x 1 (OD 3.5mm Ear phone Jack)
Select & Function buttons on front panel
RS 232 series interface
Infrared Frequency 38 Khz
IR External Distance ~1000 feet / 300 meters maximum.
HDMI I/O Connector HDMI Type A - SMD 19pin Female Type
Dimensions LxWxH=19＂x 9.85 ＂x 3.50＂(482mm x250mmx 88mm)
Rack Mount 2RU High 19 ＂Rack Mount #2U-440L (with rack mount)
Power Supply AC 100~230 VAC 50/60Hz
Power Consumption 5880 mA Maximum
Temperature
32 F - 100 F Operation(0 C - 32 C)
Safety Approvals CE,FCC, RoHS (2002/95/EC).
Product Weight 4.75 Kgs/7.91lb
Source Status Automatically Scan Sources Inputs via LED show out
Function Control Key ALL / OFF / RECALL / ENTER / MEMORY / LOCK / EDID
CAT5e/6 Extender Distance ~300 feet / 100 meters maximum.
Inputs
Outputs
HDBaseT Distance 100m/328ft CAT5e/6 cable with RJ45 connectors
8x HDMI Sources
1x IR Ext. in (IR To Switcher)
8x IRs (To 8x Rooms - Enabled by using HDBaseT Specifications)
1x ALL IR in (IR to Room - Enabled by using HDBaseT Specifications)
1x RS-232 (Command Switcher)
8x RS-232 (To 8x Rooms - Enabled by using HDBaseT Specifications)
8x HDMI Destinations
8x CAT5e/6/7 (Enabled by using HDBaseT Specifications)
1x ALL IR out (IR from Room - Enabled by using HDBaseT Specifications)
8x IRs (From 8x Rooms - Enabled by using HDBaseT Specifications)
8x RS-232 (From 8x Rooms - Enabled by using HDBaseT Specifications)

OUTPUT 1 2 3 4 5 6 7 8
INPUT 8 67 5 4 3 2 1
FRONT PANEL
FRONT PANEL
325
POWER SWITCH
DESTINATION SELECT BUTTONS
1
4
The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and
is receiving power.
The Switcher will remember that last state during a power cycle.
When power is removed and resorted, the last configuration will be evoked.
INPUT STATUS DISPLAY
2
Input sources 1 to 8 LED illuminates blue to indicate that a video source is present on that input.
Separate outputs 1 thru 8 select buttons are provided for each destination assignment.
Routing can be Source to Destination or one source to multiple destinations.
Example : Press Destination 1,3,5 then press Source 2 will route Input 2 to Output 1,3,5 respectfully.
OUTPUT STATUS DISPLAY
3
Each Output (destination ) Channel shows which input (source) is assigned.
IR SENSOR
6
The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.
EDID MODE SELECT BUTTONS
5
Used to select EDID mode using buttons #1 thru #2
SOURCE SELECT BUTTONS
7
Separate inputs 1 thru 8 select buttons are provided each source selection.
1647
PAGE 7SB-5688CT INSTRUCTION & OPERATION MANUAL
POWER
SB-5688CT
1 2
SOURCE STATUS
3 4 5 6 7 8
8x8 HDMI CAT6 MATRIX SWITCHER
ALL OFF RECALL MEMORY EDID
ENTER LOCK
1 2 3 5 6 7 8
SOURCE
DESTINATION
SOURCE
DESTINATION
4
1 2 3 5 6 7 8 4
IR
15
19 INCH EAR MOUNT PAIR
Converts desktop to 19 inch rack mount. Bracket (part # 1U-440L) INCLUDED.
Image shows rack mount bracket attached.
15

FRONT PANEL
FRONT PANEL
911 10
PAGE 8 SB-5688CT INSTRUCTION & OPERATION MANUAL
FUNCTION KEY - OFF
9
FUNCTION KEY - LOCK
- Press and hold LOCK button for two seconds lockout the front panel.
- Press and hold LOCK button for two seconds to enable the front panel.
11
FUNCTION KEY - ENTER
10
Disables (mute) video to selected channels. Either destinations.
- Press OFF button followed by any Destination channel.
- Press 1 thru 4 output destination. The display will show " 0 " for the selected
channel indicating no video selected.
POWER
SB-5688CT
1 2
SOURCE STATUS
3 4 5 6 7 8
8x8 HDMI CAT6 MATRIX SWITCHER
ALL OFF RECALL MEMORY
EDID ENTERLOCK
1 2 3 5 6 7 8
SOURCE
DESTINATION
SOURCE
DESTINATION
4
1 2 3 5 6 7 8 4
IR
OUTPUT 1 2 3 4 5 6 7 8
INPUT 8 67 5 4 3 2 1
8
FUNCTION KEY - ALL
Disables (mute) video on all destinations OR Selects the same source to all destinations.
Option 1
- Press ALL followed by OFF button. The display will show " 0 " indicating all destinations have no video
selected.
Option 2
- Press ALL followed by Source 1 thru 8. The display will show the Source selected.
- Press ENTER The pre-set source selection will be assigned all destinations.
8
OFF 1 2 0 3 4 0 5 0
INPUT 1 2 3 4 5 6 7 8
ALL 1 2 3 4 5 6 7 8
INPUT 1 1 1 1 1 1 1 1
LOCK 1 2 3 4 5 6 7 8
INPUT 1 2 3 4 5 6 7 8
Press ENTER to confirm entries.

FRONT PANEL
FRONT PANEL
12 13
14
PAGE 9SB-5688CT INSTRUCTION & OPERATION MANUAL
FUNCTION KEY - MEMORY
13
FUNCTION KEY - RECALL
The system will show store presets, up to a total of 16.
Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8
as the memory preset location.
- Configure desired matrices..
- Press button.
- Press 1 thru 4 on either Source or Destination row.
- Press ENTER to ready memory location.
- or press MEMORY again to cancel operation.
Operation completes.
Note : Operation will abort if no keys are pressed within 5 seconds.
MEMORY
The system will show previously stored presets, up to a total of 16.
Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8
as the memory preset location.
- press RECALL button.
- press 1 thru 4 on either Source or Destination row.
- press ENTER The pre-set configuration will execute.
Operation completes.
Note: Operation will abort if no keys are dressed within 5 seconds.
12
POWER
SB-5688CT
1 2
SOURCE STATUS
3 4 5 6 7 8
8x8 HDMI CAT6 MATRIX SWITCHER
ALL OFF RECALL MEMORY
EDID ENTERLOCK
1 2 3 5 6 7 8
SOURCE
DESTINATION
SOURCE
DESTINATION
4
1 2 3 5 6 7 8 4
IR
OUTPUT 1 2 3 4 5 6 7 8
INPUT 8 67 5 4 3 2 1
RECALL 1 2 3 4 5 6 7 8
INPUT 1 2 3 4 5 6 7 8
MEMORY 1 2 3 4 5 6 7 8
INPUT 1 2 3 4 5 6 7 8
FUNCTION KEY - EDID
- press EDID to select new EDID mode or select
source row #1 or #2 for LINK source EDID again.
14
EDID 1 2 3 4 5 6 7 8
LEARNING
EDID 1 2 3 4 5 6 7 8
3. H24-3D, MULTI AUDIO
- press DESTINATION again, press the same DESTINATION #
to learn CATx EDID,
The EDID for CATx has been learned.

REAR PANEL
PAGE 10 SB-5688CT INSTRUCTION & OPERATION MANUAL
1
REAR PANEL
2
3
1
3
2
INPUTS- 1,2,3,4,5,6,7, & 8 HDMI
5
HDMI Digital Video/Audio, Connector with fix screw
Input 1 ~ Input 8
RS 232 CONNECTION (SWITCHER)
RS 232 control port to allow for interfacing to a PC
Such as a computer or touch panel control, to the switcher
via this DB-9pin Female connector for serial RS-232 control.
,
IR EXTERNAL IN (EXT. IR TO CONTROL SWITCHER)
POWER INLET
The Switcher is fitted with a AC power plug input connector.
Ensure that the used is of an approved type and is of sufficient
current carrying connector capacity with the correct voltage and
connector polarity. 100~240Volt AC, 50/60Hz power supply.
Support one of IR Extender to control Switcher
Extend distance maximum 300Meters / ~1000 feet
When you plug the External IR extender into the switcher,
the front panel IR receiver remain active.
OUTPUTS- 1,2,3,4,5,6,7 & 8 HDMI
4
HDMI Digital Video/Audio, Connector with fix screw
Output 1 ~ Output 8
Remote port :
DB-9pin Female connector
HDMI digital video/audio connector:
HDMI Female connector.
Connect a signal link of HDMI direct digital video/audio to
this Female HDMI connector. This connector supports HDMI
digital video/audio and DVI digital video sources. Note:
With the proper adapters, the switcher
can be used with DVI digital video signals
HDCP compliant. DVI does not support audio.
Connect a signal link of HDMI direct digital video/audio to
this Female HDMI connector. This connector supports HDMI
digital video/audio and DVI digital video sources.
HDMI digital video/audio connector:
HDMI Female connector.
Note:
With the proper adapters, the switcher
can be used with DVI digital video signals
HDCP compliant.
Power Plug:
Power input - AC100~240V,50/60Hz, 10A
IR Extender Jack:
Female Jack - inner OD O 3.5 mm
45
8
INPUT
8
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
7
INPUT
7
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
6
INPUT
6
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
5
INPUT
5
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
4
INPUT
4
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
3
INPUT
3
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
2
INPUT
2
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
1
INPUT
1
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
RS-232
RoH S/9 5/EC
RoHS
8
POWER AC100V~AC240V-50/60Hz.
IR From ROOM
7 6 5 4 3 2 1
ALL out
8
IR To ROOM
7 6 5 4 3 2 1
ALL in
SW IR in

8
INPUT
8
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
7
INPUT
7
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
6
INPUT
6
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
5
INPUT
5
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
4
INPUT
4
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
3
INPUT
3
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
2
INPUT
2
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
1
INPUT
1
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
RS-232
RoH S/9 5/EC
RoHS
8
POWER AC100V~AC240V-50/60Hz.
IR From ROOM
7 6 5 4 3 2 1
ALL out
8
IR To ROOM
7 6 5 4 3 2 1
ALL in
SW IR in
REAR PANEL
REAR PANEL
PAGE 11SB-5688CT INSTRUCTION & OPERATION MANUAL
10
9
7
6RS 232- CONNECTION TO CONTROL ROOM1,2,3,4,5,6,7 & 8
8x RS 232 control port to allow for interfacing to a PC
Such as a computer or touch panel control, to the switcher
via this DB-9pin Female connector for serial RS-232 control.
, Remote port :
DB-9pin Female connector
OUTPUT - 1,2,3,4,5,6,7 & 8 CAT
7
Connector with RJ-45 Output 1 ~ Output 8
CAT Transmitter extend a signal link of HDMI / RS232 / IR Remote
to this RJ-45 Female connector via CAT5e/6 cable.
CAT connector:
RJ-45 Female connector.
8IR REMOTE INPUT - 1,2,3,4,5,6,7 & 8 IR SIGNAL TO ROOM
Support eight of IR Extender to control signal to eight rooms
Extend cable distance maximum 300Meters / ~1000 feet
When you plug the CAT5e/6/7 IR extender into the external port,
the room IR receiver remain active.
IR Extender Jack:
Female Jack - inner OD O 3.5 mm
86 11
9IR REMOTE OUTPUT - 1,2,3,4,5,6,7 & 8 IR SIGNAL FROM ROOM
Support eight of IR Extender to receive signal from eight rooms
Extend cable distance maximum 300Meters / ~1000 feet
When you plug the CAT5e/6/7 IR extender into the external port,
the room IR receiver remain active.
IR Extender Jack:
Female Jack - inner OD O 3.5 mm
10 ALL IN : ALL IR REMOTE HDBaseT 1,2,3,4,5,6,7 & 8 (IR SIGNAL TO ROOM)
Support eight of IR remote signals to control to eight rooms via ALL IN port.
Extend cable distance maximum 300Meters / ~1000 feet
When you plug the CAT5e/6/7 IR extender into the external port,
the room IR receiver remain active.
IR Extender Jack:
Female Jack - inner OD O 3.5 mm
11 ALL OUT : ALL IR REMOTE HDBaseT - 1,2,3,4,5,6,7 & 8 (IR SIGNAL FROM ROOM)
Support eight of IR remote signals from eight rooms via ALL OUT port.
Extend cable distance maximum 300Meters / ~1000 feet
When you plug the CAT5e/6/7 IR extender into the external port,
the room IR receiver remain active.
IR Extender Jack:
Female Jack - inner OD O 3.5 mm

EDID function for HDMI Matrix Switcher
PAGE 12 SB-5688CT INSTRUCTION & OPERATION MANUAL
EDID FUNCTION
Press
6.1 Embedded EDID modes Total 8 EDID Modes
Operation will abort if no keys are pressed within 5 seconds.
EDID setup
Step 1 . Press the EDID button The display will show the currently selected EDID mode
Step 2 . Press SOURCE #1 or #2
button row
The button will flash blue and the display will show
the current Embedded EDID Status.
Step 3 . Press the ENTER button To set EDID mode.
The switcher will return to operation mode.
Select Embedded EDID :
Mode 1 : FSS
Mode 2 : H24-3D
Mode 3 : H24-3D-M
Mode 4 : H36-3D
Mode 5 : H36-3D-M
Mode 6 : 1280x1024-60Hz
Mode 7 : 1920x1200-60Hz
Mode 8 : AUTO
EDID
>
SOURCE
>
ENTER
Embedded EDID setup
To change the EDID setup
Repeatedly depressing the source 1 button will cycle up thru the options.
Repeatedly depressing the source 2 button will cycle down thru the options.
to select Embedded EDID mode or LEARNING mode.
SOURCE #1
or
SOURCE #2
EDID 1 2 3 4 5 6 7 8
2. H24-3D, PCM 2CH
Press EDID button : The LCM will show the current EDID status.

EDID FUNCTION
PAGE 13SB-5688CT INSTRUCTION & OPERATION MANUAL
EDID function for HDMI Matrix Switcher
Learning EDID setup for CATx
Key Press Sequence:
EDID > DESTINATION # > SOURCE # > ENTER
Again, Press the same DESTINATION # to
learn CATx EDID The EDID for CATx has
been learned
Switcher will LEARN destination HDMI EDID
and pass the selected source.
6.2 LEARNING EDID
Learning EDID from Destination to Source
NOTE : The already learned EDID cannot be modified. You can only rebuild a new Learning EDID.
For example;
When the Source has "Learned" the EDID data from a destination, It will save that EDID
information into EPROM and the EDID data cannot change.
Please select new learning destination to sources or change to one of the embedded EDID modes
when you want to remove the learning EDID memory from EPRPM.
Press
Learning EDID setup
EDID
>
SOURCE
>
ENTERDESTINATION
>
Press EDID > DESTINATION Button:
EDID 1 2 3 4 5 6 7 8
LEARNING HDMI
The LCM will be show LEARNING.
EDID 1 2 3 4 5 6 7 8
LEARNING CATX
Press EDID > DESTINATION Button: > DESTINATION
Press
EDID
>
SOURCE
>
ENTERDESTINATION
>
DESTINATION
>
Switcher will LEARN destination CATx EDID
and pass the selected source.
Learning EDID setup for HDMI
Key Press Sequence:
EDID > DESTINATION # > SOURCE # > ENTER
The EDID for HDMI has been learned

EDID function for HDMI Matrix Switcher
PAGE 14 SB-5688CT INSTRUCTION & OPERATION MANUAL
EDID FUNCTION
Mode 4 . H36 (1080p-36 bits)
Audio Support :
PCM 2CH
Mode 5 . H36-M (1080p-36 bits)
Audio Support :
MAT(MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3 5.1CH,
DTS 5.1CH, PCM 7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH
Mode 8 . AUTO <Default>
All Outputs will be set to the highest common
resolution of all connected display devices.
Mode 6 . 1280x1024-60Hz (DVI-D)
DVI Support :
DVI-D 1280x1024 60Hz
Mode 7 . 1920x1200-60Hz (DVI-D)
DVI Support :
DVI-D 1920 x 1200 60Hz
Mode 1 . FSS (Fast Speed Start)
Automatic capture most suitable EDID from
Destination to Source.
Mode 2 . H24-3D (1080p-24 bits)
Audio Support :
PCM 2CH
R
Mode 3 . H24-3D-M (1080p-24bits)
Audio Support :
MAT(MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3 5.1CH,
DTS 5.1CH, PCM 7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH
EDID 1 2 3 4 5 6 7 8
1. FAST SPEED START
EDID 1 2 3 4 5 6 7 8
2. H24-3D, PCM 2CH
EDID 1 2 3 4 5 6 7 8
3. H24-3D, MULTI AUDIO
EDID 1 2 3 4 5 6 7 8
4. H36-3D, PCM2CH
EDID 1 2 3 4 5 6 7 8
5. H36-3D, MULTI AUDIO
EDID 1 2 3 4 5 6 7 8
8. AUTO MODE
EDID 1 2 3 4 5 6 7 8
6.1280x1024-60HZ DVI-D
EDID 1 2 3 4 5 6 7 8
7.1920x1200-60HZ DVI-D

EDID function for HDMI Matrix Switcher
PAGE 15SB-5688CT INSTRUCTION & OPERATION MANUAL
EDID FUNCTION
6.2.1
Step 1 . Press EDID button
Example : Learn Destination #8 EDID To Source #5.
The button will flash blue and the display will show
the current Embedded EDID Status.
Learning EDID Single to Single
Step 2 . Press the Destination #8 button row Copy the Destination #8 Display EDID.
Step 3 . Press the Source #5 button row Learning the Destination #8 EDID To Source # 5.
Step 4 .
Press ENTER button To confirm entries.
6.2.3
Step 3 .
Press EDID button
Learning destination EDID link to All Sources
The button will flash blue and the display will show
the current Embedded EDID Status.
Learning EDID Single to ALL
Step 1 .
Press destination button 1 thru 8 Learning anyone 1~8 Destination EDID to all sources.
Step 4 . Press ENTER button
To confirm entries.
Step 2 .
Press ALL button Learning selected destination EDID to all sources.
6.2.2
Step 3 .
Press EDID button
Learning destination EDID link to the majority Sources
The button will flash blue and the display will show
the current Embedded EDID Status.
Learning EDID Single to multiple
Step 1 .
Step 4 . Press ENTER button To confirm entries.
Step 2 . Press the Destinations #1~8 button row
Copy any 1~8 Destinations EDID.
Learning the Destination EDID link to source #1,#6,~#8 .
Press the Source #1, #6,~#8 button row
Step 4 .

EDID function for HDMI Matrix Switcher
PAGE 16 SB-5688CT INSTRUCTION & OPERATION MANUAL
EDID FUNCTION
2. To set up learning between a single destination and single source:
Press EDID button > Press Destination 1 thru 8 > Press Source 1 thru 8 > Press ENTER to confirm.
Switcher will learn destination EDID to source device.
3. To set up learning between a single destination and Multiple sources:
Press EDID button > Press Destination 1 thru 8 > Press the majority Sources 1 thru 8 > Press ENTER.
Switcher will learn single destination EDID to many source devices.
4. How to Learning single destinations with all sources.
Press EDID button > Press ALL button > Press ENTER to confirm.
Example for single source
Destination > press #1 and then Source > press #1
Destination device #1 will set to the highest common resolution and Audio of source #1
Example for multiple sources
Destination device #1, #2, #3 will be set to the highest common resolution and Audio
available and source device #1 will output this same resolution.
6.6 Auto mode definition
Common Resolution and Audio
Switcher will find highest common Resolution and Audio from all destination EDID
to link Source.
6.4
Step 2 . Press EDID button
Fast speed start
Select a optimum status of Embedded EDID mode.
How to setup FSS Function
Step 4 . Press EDID button To select the EDID FSS mode.
Step 5 . Press ENTER button To conform entries.
Step 1 . Press the Destination #1~8 button row To setup and Install all devices.
Then Press the Source #1~8 button row
R
R
Step 3 . Press ENTER button To conform entries.
R
6.3 EDID status
Step 1 . Press EDID button
Step 2 . Press EDID button
To view the current EDID status.
The button will flash blue and the display will show
the current Embedded EDID Status.
To exit.
1. Switcher will LEARN destination EDID and pass the selected source.
6.5 LEARNING EDID definition
Learning EDID from Destination to Source

TYPICAL APPLICATION
Support HDBaseT Extender by SB-6335 Transmitter and SB-6335R Receiver via CAT5e/6/7 cable
PAGE 17SB-5688CT INSTRUCTION & OPERATION MANUAL
INSTALLING DIAGRAM
PC RS232 Control
Blu-ray
SB-6335R
IR from SB-5688CT Transmitter
HDMI Projector
SB-100
IR-Receiver
IR Extender Cable
SB-101
IR-Transmitter
To Projector
IR Extender Cable
IR out
Projector IR Remote
CAT5e/6/7 Extension Cable Limited to 330 feet (100M)
HDMI out
NOTE:
1. IR Control Projector Over HDBaseT Extender:
SB-5688CT HDBaseT Transmitter
SB-6335R HDBaseT Receiver
2. Projector RS-232 Control by a PC via CAT6 TX.
3. Projector IR control via CAT6 IR in (IR To projector).
4. IR Extender Transmitter (SB-101):
Use SB-101 IR Transmitter to Extend IR signal to
Projector.
5. IR Extender Receiver (SB-100):
Use SB-100 IR Receiver to receive the Projector IR
Remote signal.
Sample connection using IR Transmitters (SB-101) and IR Receiver (SB-100) with SB-6335R & SB-5688CT
to control a projector.
8
INPUT
8
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
7
INPUT
7
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
6
INPUT
6
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
5
INPUT
5
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
4
INPUT
4
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
3
INPUT
3
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
2
INPUT
2
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
1
INPUT
1
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
RS-232
RoH S/9 5/EC
RoHS
8
POWER AC100V~AC240V-50/60Hz.
IR From ROOM
7 6 5 4 3 2 1
ALL out
8
IR To ROOM
7 6 5 4 3 2 1
ALL in
SW IR in

TYPICAL APPLICATION
Support HDBaseT Extender by SB-6335 Transmitter and SB-6335R Receiver via CAT5e/6/7 cable
PAGE 18 SB-5688CT INSTRUCTION & OPERATION MANUAL
INSTALLING DIAGRAM 8x8 HDMI MATRIX SWITCHER
AU DIO AMP LIFIE R
SB-5609
Audio Extractor
Audio Amplifier
Audio Mixer
SB-6335R
Extender-Receiver
IR Extender Cable
SB-101
IR Signal from Satellite
Receiver Remote Control
Satellite Receiver Remote Control
ARC
HD Satellite Receiver
IR in
CAT6 in
HDMI out
NOTE :
1. IR Control Satellite Receiver Over HDBaseT
CAT5e/6/7 Extender from room:
SB-5688CT HDBaseT CAT5e/6/7 Transmitter
SB-6335R HDBaseT CAT5e/6/7 Receiver
2. Destination RS232 Control :
Via SB-5688CT TX RS232 in.
3. IR Extender Transmitter (SB-101):
Use SB-101 IR Transmitter to Extend IR signal.
Sample connection using IR Transmitters (SB-101) with SB-5688CT and SB-6335R to control a IR signal from
Satellite Receiver.
CAT5e/6/7 Extension Cable Limited to 330 feet (100M)
8
INPUT
8
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
7
INPUT
7
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
6
INPUT
6
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
5
INPUT
5
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
4
INPUT
4
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
3
INPUT
3
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
2
INPUT
2
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
1
INPUT
1
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
RS-232
RoH S/9 5/EC
RoHS
8
POWER AC100V~AC240V-50/60Hz.
IR From ROOM
7 6 5 4 3 2 1
ALL out
8
IR To ROOM
7 6 5 4 3 2 1
ALL in
SW IR in
PC RS232 Control
IR Trnasmitter

INSTALLING DIAGRAM
TYPICAL APPLICATION
8x8 HDMI-CAT5e/6 MATRIX SWITCHER
Application HDBaseT IR, RS-232, Multi format Audio and HD Video signals to pass over CXAT5e/6/7 cable.
PAGE 19SB-5688CT INSTRUCTION & OPERATION MANUAL
Blu-ray
HDMI DISPLAY
HDTV
SB-100
IR-Receiver
IR Extender Cable
SB-5688CT IR
HD Satellite Receiver
8
INPUT
8
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
7
INPUT
7
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
6
INPUT
6
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
5
INPUT
5
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
4
INPUT
4
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
3
INPUT
3
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
2
INPUT
2
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
1
INPUT
1
CAT5e/6/7
OUTPUT
RS232-TX-RX
HDMI
RS-232
RoH S/9 5/EC
RoHS
8
POWER AC100V~AC240V-50/60Hz.
IR From ROOM
7 6 5 4 3 2 1
ALL out
8
IR To ROOM
7 6 5 4 3 2 1
ALL in
SW IR in
PC RS232 Control
NOTE :
1. Audio Extractor To Recode Audio :
SB-5609 HDMI Audio Extractor.
2. Control HDMI ARC:
SB-5610 ARC Control Box.
3. RS232 Control Via a PC.
4. Switcher IR External port :
Via SB-100 IR Extender Receiver.
5. HDMI Display :
Signal from Blu-Ray or HD Satellite Receiver.
Sample connection using Audio Extractor To Recode Audio (SB-5609) or to control ARC (SB-5610) and
Extend the HDMI signal via HDBaseT Transmitter to IR Receivers (SB-6335R) with SB-5688CT
to extend 100M distance between switcher and destination..
HDMI DISPLAY
ARC
TV
SB-5610
ARC Control Box
ARC Device
ARC
HDMI output to SB-5610

Before making any connections to the switcher. Observe the following:
> Ensure the mains voltage supply matches the label on the supplied plug-
Pack (+/- 10%)
> Ensure that the power switch is OFF
> Ensure that all system grounds (earth) are connected to a common point.
> Avoid powering equipment within a system from multiple power sources
that may be separated by large distances
REMOTE CONTROL
REMOTE CONTROL
> Connect all audio video sources and destination equipment
> power up all source and destination audio-visual sources
> For each destination output select the appropriate input source by using
> Upon power up the switcher will return to its last used setting before
The front panel input 1~8 select buttons. The supplied IR remote control.
Or through the RS 232 serial communications port.
Powered down.
PAGE 20 SB-5688 INSTRUCTION & OPERATION MANUAL
POWER
1 2 3 4
5 6 7 8
ON OFF
MEMORY
DESTINATION
SOURCES
RECALL
1 2 3 4
5 6 7 8
ENTER LOCK
EDID
ALL OFF
8x8 HDMI MATRIX SWITCHER
ENIRPA5688000A2
SW-5688
SWITCH POWER ON or OFF
1
Controller with a separate power ON and OFF
DESTINATION : 1 thru 8 OUTPUT SELECTION
Press the destination button to select the output
display channel.
2
3
FUNCTION KEY
ALL
OFF
EDID
RECALL
MEMORY
ENTER
LOCK
5
SOURCE : 1 thru 8 INPUT SOURCE SELECTION
Press input 1~8 sources with selection button
4
3
4
5
2
1
IR REMOTE : SW-5688
IR REMOTE CONTROL KEY :
- function selection button
- function selection button
- function selection button
- function selection button
- function selection button
- function selection button
- function selection button