SHOPPINGALL SA-GM112D User manual

SA-GM112D
0-8kgs/0-17.6lbs
Load
15” - 32” 75x75, 100x100
VESA
-90°/+85°
Tilt
180°
Swivel
Rotate
360°
Gas Spring Monitor Desk mount
Thank you for choosing our product. ShoppingAll is dedicated to providing
the highest level of quality and service to our customers. If you are satisfied
with the item, would you kindly share your feedback on Amazon?
Please do not hesitate to contact us if you have any issue.
Call: [phone]
Mon-Fri 8:00am – 9:00pm (Eastern Time) (Canada/USA)
Email: [email protected] Website: www.ShoppingAll.com
Installation Video

WARNING STATEMENTS
PRODUCT LINE GRAPH
01
Ⅰ Ⅱ
310mm/12.2”
0-350mm/0-13.8”
360
90
85
180
45
360mm/14.2”
Warning
Prior to the installation of this product, the installation instruction must be read
and completely understood. Failure to do so may result in personal injury,
property damage or voiding of manufacturer warranty.
Do not install on a structure that is prone to vibration, or movement. Reinforce
the structure as required before installation.
Pay attention to the weight capacity of the mount. Exceeding the limitation can
result in impairment or serious injury and property damage.
Never operate the mount if parts are missing or damaged. Contact your local
service center for warranty service.
Do not use this product for any purpose or in any configuration not explicitly
specified in this instruction. We hereby disclaim any and all liability for injury or
damage arising from incorrect assembly, Incorrect mounting, or incorrect use of
this product.
Recommended mounting surfaces: Wooden studs or solid-flat concrete. If the mount
is to be installed on any surface other than wooden studs, use suitable hardware.

PARTS INCLUDED
a
b
02
c
M4x8 (x4) M4x12 (x4) M4x30 (x4)
(x1)12X5.8X16 (x4)
(x1)
S=3mm (x1)
S=4mm (x1) S=5mm
A
B
C
D
E
M6x25 (x1) (x1)
(x1)
Extra screw
(x2)

03
Clamp Installation Steps
1
For desk thickness more than 2.36"(60mm) but within 3.35"(85mm), remove clamp
screw and attachment entirely and reattach clamp screw with bottom plate
upside-down.
D
S=4mm
S=5mm
S=3mm
S=5mm
S=4mm S=4mm
①
①
②
②
③
③
④
④

04
Grommet Installation Steps
D
S=4mm
S=5mm
S=3mm
E
E
OR
S=4mm
S=4mm
S=4mm
S=5mm
S=5mm
⑥⑤
①②
Remove Clamp from the base Install Grommet (Part E) to the base
③ ④

05
2
c
Adjust the Height Adjustment Ring at proper height and screw uptight to
the pole. Put the Extension Arm onto the pole and install Spring Arm
onto the Extension Arm.
Adjust the height adjustment ring at proper height and screw uptight to the
pole. Put on the spring arm to the pole.
C
M6x25
D
S=4mm
OR
Arm Installation
Insert and fasten the screw
from the bottom of the arm
joint to the plastic
Connection Cap.

06
D
S=4mm
Monitor Installation
Gas Spring Tension Adjustment
NOTE: Turn clockwise to reduce
tension for lighter monitors and
counter-clockwise to increase
tension for heavier monitors.
S=5mm
4
Use a hex wrench to adjust the height tension of the gas spring arm, to
keep different weight of monitors still at any position.
3
B
M4x30
12X5.8X16
A
M4x12
M4x8
OR
X
TVTV TV TV
S=4mm
S=4mm
Press down the
arm to a horizontal
position
1 turn ≈ 1 lbs ≈ 0.4kg

07
Tilt & Swivel Adjustment
Cable Management Installation
5
6
B
Organize cables with cable management clips along the pole.
D
S=3mm
S=5mm
Tighten the bolt with the Allen Key to make the tilt and swivel adjustment.
S=3mm
Use the cable clip to manage
the wrenches when not used.
S=4mm
S=5mm
S=3mm
D
S=4mm
S=5mm
S=3mm
S=5mm
VESA Tilt Adjustment VESA Swivel Adjustment
Arm Swivel
Adjustment
S=5mm