Show Tec TR-512 User manual

TR-512 Install
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Product code: 50826
USER MANUAL
ENGLISH
V1

1
TR-512 Install
Product code: 50826
Preface
Thank you for purchasing this Showtec product.
The purpose of this user manual is to provide instructions for the correct and safe use of this product.
Keep the user manual for future reference as it is an integral part of the product. The user manual shall be
stored at an easily accessible location.
This user manual contains information concerning:
●Safety instructions
●Intended and non-intended use of the device
●Installation and operation of the device
●Maintenance procedures
●Troubleshooting
●Transport, storage and disposal of the device
Non-observance of the instructions in this user manual may result in serious injuries and damage of
property.
©2021 Showtec. All rights reserved.
No part of this document may be copied, published or otherwise reproduced without the prior written
consent of Highlite International.
Design and product specifications are subject to change without prior notice.
For the latest version of this document, please visit our website www.highlite.com or contact us at
[e-mail].
Highlite International and its authorized service providers are not liable for any injury, damage, direct or
indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or
reliance on the information contained in this document.

2
TR-512 Install
Product code: 50826
Table of contents
1. Introduction................................................................................................................................................... 4
Before Using the Product ..................................................................................................................................4
Intended Use.......................................................................................................................................................4
Text Conventions................................................................................................................................................4
Symbols and Signal Words................................................................................................................................5
Symbols on the Information Label ..................................................................................................................5
2. Safety............................................................................................................................................................. 6
Warnings and Safety Instructions ....................................................................................................................6
Requirements for the User.................................................................................................................................7
3. Description of the Device............................................................................................................................. 8
Front View ............................................................................................................................................................8
Product Specifications ......................................................................................................................................9
Dimensions.........................................................................................................................................................10
4. Installation................................................................................................................................................... 11
Safety Instructions for Installation ..................................................................................................................11
Installation Site Requirements ........................................................................................................................11
DIN Rail Mounting.............................................................................................................................................11
Connecting to Power Supply.........................................................................................................................12
5. Setup ........................................................................................................................................................... 13
Warnings and Precautions .............................................................................................................................13
DMX Connection..............................................................................................................................................13
DMX-512 Protocol .......................................................................................................................................13
DMX Cables .................................................................................................................................................13
Setup Examples ................................................................................................................................................14
Program Recording Setup ........................................................................................................................14
Program Playing Setup ..............................................................................................................................15
Connecting External Trigger Devices .............................................................................................16
Connecting the TR-512 Install-Wall Panel ......................................................................................17
6. Operation.................................................................................................................................................... 19
Safety Instructions for Operation...................................................................................................................19
Start-up...............................................................................................................................................................19
Control Panel ....................................................................................................................................................20
Recording a Program......................................................................................................................................20
Playing a Program............................................................................................................................................20
Trigger Monitoring ............................................................................................................................................21
LED Statuses.......................................................................................................................................................21
Menu Overview ................................................................................................................................................22
Main Menu Options .........................................................................................................................................23
Play Show .....................................................................................................................................................23
Show .....................................................................................................................................................23
Mode ....................................................................................................................................................24
Record Show ...............................................................................................................................................24
Name....................................................................................................................................................24
Mode ....................................................................................................................................................25
Delete Show.................................................................................................................................................25
Trigger Event ................................................................................................................................................26
Status ....................................................................................................................................................26
Rename................................................................................................................................................26
Show .....................................................................................................................................................27
Mode ....................................................................................................................................................27
Delay.....................................................................................................................................................27
Stop TR Event ...............................................................................................................................................28
Device Settings............................................................................................................................................28

3
TR-512 Install
Product code: 50826
Device Label.......................................................................................................................................28
DMX Port Option.................................................................................................................................29
Display Option.....................................................................................................................................29
Version..................................................................................................................................................29
Save Configuration ....................................................................................................................................30
Load Configuration....................................................................................................................................31
Default Setting.............................................................................................................................................31
7. Troubleshooting .......................................................................................................................................... 32
8. Maintenance .............................................................................................................................................. 33
Preventive Maintenance................................................................................................................................33
Basic Cleaning Instructions .......................................................................................................................33
Corrective Maintenance................................................................................................................................33
9. Deinstallation, Transportation and Storage ............................................................................................... 34
10. Disposal ....................................................................................................................................................... 34
11. Approval ..................................................................................................................................................... 34

4
TR-512 Install
Product code: 50826
1. Introduction
Before Using the Product
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your
Highlite International dealer.
Your shipment includes:
●Showtec TR-512 Install
●MicroSD card
●User manual
Fig. 01
Intended Use
This device is designed to be used as a professional DMX trigger/recorder. It is suitable for indoor
installation in an electrical enclosure.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Text Conventions
Throughout the user manual the following text conventions are used:
●Buttons: All buttons are in bold lettering, for example “Press the UP/DOWN buttons”
●References: References to chapters and parts of the device are in bold lettering, for example:
“Refer to 2. Safety”, “press the power switch (03)”
●0–255: Defines a range of values
●Notes: Note: (in bold lettering) is followed by useful information or tips

5
TR-512 Install
Product code: 50826
Symbols and Signal Words
Safety notes and warnings are indicated throughout the user manual by safety signs.
Always follow the instructions provided in this user manual.
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
Indicates an imminently hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
Attention
Indicates important information for the correct operation and use of the
product.
Important
Read and observe the instructions in this document.
Provides important information about the disposal of this product.
Symbols on the Information Label
This product is provided with an information label. The information label is located on the bottom plate of
the device.
The information label contains the following symbols:
This device is designed for indoor use.
This device is IEC protection class III.
This device shall not be treated as household waste.
Read and observe the instructions in this document.

6
TR-512 Install
Product code: 50826
2. Safety
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
Warnings and Safety Instructions
Attention
Power supply
This device falls under IEC protection class III. This device shall be connected to an external power
supply.
●Before connecting the device to the external power supply, make sure that the current, voltage and
frequency match the input voltage, current and frequency specified on the information label on the
device.
●Make sure that the cross-sectional area of the power cable is sufficient for the required power
consumption of the device.
Attention
General safety
●Do not block the ventilation openings. Without proper heat dissipation and air circulation, the
internal components may overheat. This can result in product damage.
●Do not shake the device. Avoid brute force when installing or operating the device.
Attention
For professional use only
This device shall be used only for the purposes it is designed for.
This device is designed to be used as a professional DMX trigger/recorder. It is suitable for indoor
installation in an electrical enclosure. Any incorrect use may lead to hazardous situations and result in
injuries and material damage.
●This device is not suitable for households.
●This device does not contain user-serviceable parts. Unauthorized modifications to the device will
render the warranty void. Such modifications may result in injuries and material damage.

7
TR-512 Install
Product code: 50826
Attention
Do not expose the device to conditions that exceed the rated IP class conditions.
This device is IP20 rated. IP (Ingress Protection) 20 class provides protection against solid objects greater
than 12 mm, such as fingers, and no protection against harmful ingress of water.
Requirements for the User
This product may be used by ordinary persons. Maintenance, installation and service shall be carried out
only by instructed or skilled persons. Contact your Highlite International dealer for more information.
Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled
person, for specific tasks and work activities associated with the service of this product, so that they can
identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards
associated with the service of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons
include not only users of the product but also any other persons that may have access to the device or
who may be in the vicinity of the device.

8
TR-512 Install
Product code: 50826
3. Description of the Device
The TR-512 Install is a compact but very powerful tool which can be used for triggering any light show or
scene in a simple way. It can record and play several DMX programs at the same time. Those programs
can be stored on a microSD card. Programs can be played by 6 external triggers or by the internal auto
trigger. Each trigger can start either a program or a scene. Each program can be played in a loop mode
or single play mode. It is also possible to set a delay, which enhances your control of the programs.
The TR-512 Install is suitable for a large range of venues, such as: theme parks, museums, shops and many
others.
Front View
Fig. 02
01) 12 V DC 2-pin Phoenix terminal power connector IN
02) MicroSD card slot
03) RJ45 wall panel connector IN
04) OLED display + control buttons
05) 3-pin Phoenix terminal connector DMX IN
06) 3-pin Phoenix terminal connector DMX OUT
07) Optional 12 V output connector for external LED indicators
08) DIN rail lock
09) Triggers 1–5 (GPIO), 2-pin Phoenix terminal connector IN; Trigger 6 (GPIO), 3-pin Phoenix terminal
connector IN
10) DMX IN/Trigger LED indicator
11) Play/Record LED indicator
12) MicroSD LED indicator
13) Power LED indicator

9
TR-512 Install
Product code: 50826
Product Specifications
Model:
TR-512 Install
Electrical:
Power supply (external):
12 V DC
Power consumption:
6 W
Physical:
Dimensions:
105 x 110 x 58 mm (LxWxH)
Weight:
0,19 kg
Operation and control:
Control protocols:
DMX-512
Control panel:
OLED display and buttons
Control modes:
DMX-512A, Wall Remote, GPIO, Manual
MicroSD card capacity:
8 GB
Connections:
Power connections:
●12 V DC 2-pin Phoenix terminal power connector IN (maximum
cable gauge: 1,5 mm2/ AWG: 12)
●12 V Phoenix connector OUT (maximum cable gauge: 1,5 mm2/
AWG: 12)
Input connections:
●6 x 2-pin Phoenix terminal trigger GPIO connector IN (maximum
cable gauge: 1,5 mm2/ AWG: 12)
●3-pin Phoenix terminal DMX connector IN (maximum cable
gauge: 1,5 mm2/ AWG: 12)
●RJ45 wall panel connector IN
Output connections:
3-pin Phoenix terminal DMX connector OUT (maximum cable gauge:
1,5 mm2/ AWG: 12)
Construction:
Housing:
UL94-V0 flame retardant polycarbonate
Color:
Gray
Mounting:
35-mm DIN rail system (DIN EN43880 form factor; DIN EN60715 rail
system)
Mounting size:
6 TE
IP rating:
IP20
Thermal:
Maximum ambient temperature ta:
40 °C

10
TR-512 Install
Product code: 50826
Dimensions
Fig. 03

11
TR-512 Install
Product code: 50826
4. Installation
Safety Instructions for Installation
WARNING
Incorrect installation can cause serious injuries and damage of property.
The installation of this device shall be carried out only by instructed or skilled persons.
Before installing the device, make sure that the electrical enclosure, where the device will be mounted, is
disconnected from power supply.
Installation Site Requirements
The device must be installed only indoors.
The device can be mounted on a 35-mm DIN rail.
The maximum ambient temperature ta= 40 °C must never be exceeded.
The relative humidity must not exceed 50 % with an ambient temperature of 50 °C.
DIN Rail Mounting
The device can be mounted on a 35-mm DIN rail.
Make sure that the DIN rail is sufficiently secured to prevent it from becoming unstable or falling off.
To mount the device on a 35-mm DIN rail, follow the steps below:
Position the device on the DIN rail.
01) Push the DIN rail locks (08)to mount the device firmly on the DIN rail (see Fig. 04).
Fig. 04

12
TR-512 Install
Product code: 50826
Connecting to Power Supply
Attention
Power supply
This device falls under IEC protection class III. This device shall be connected to an external power
supply.
●Before connecting the device to the external power supply, make sure that the current, voltage and
frequency match the input voltage, current and frequency specified on the information label on the
device.
●Make sure that the cross-sectional area of the power cable is sufficient for the required power
consumption of the device.
01) Remove the 2-pin Phoenix terminal power connector IN (01).
Fig. 05
02) Connect the external power supply to the Phoenix connector. Insert the cables correctly.
Fig. 06
03) Put the Phoenix connector back in the TR-512 Install.
04) Install the TR-512 Install on a DIN rail. See 4.3. DIN Rail Mounting on page 11 for more information.
05) Connect the external power supply to the socket-outlet with its power plug.

13
TR-512 Install
Product code: 50826
5. Setup
Warnings and Precautions
Attention
Connect all data cables before supplying power.
Disconnect power supply before connecting or disconnecting data cables.
DMX Connection
DMX-512 Protocol
Use a DMX-512 controller to create DMX programs and send them to the TR-512 Install where they will be
stored on the microSD card.
The TR-512 Install has 3-pin DMX signal IN and OUT Phoenix terminal connectors.
The pin assignment is as follows:
●3-pin: pin 1 (ground), pin 2 (-), pin 3 (+)
Note:
●Maximum recommended DMX data link distance: 300 m
DMX Cables
Shielded twisted-pair cables must be used for reliable DMX connection. You can purchase DMX cables
directly from your Highlite International dealer or make your own cables.
If you use XLR audio cables for DMX data transmission, this may lead to signal degradation and unreliable
operation of the DMX network.
When you make your own DMX cables, make sure that you connect the pins and wires correctly as
shown in Fig. 07 on page 13.
Fig. 07

14
TR-512 Install
Product code: 50826
Setup Examples
Program Recording Setup
01) Remove the 3-pin Phoenix terminal DMX connector IN (05) and the 3-pin Phoenix terminal DMX
connector OUT (06).
Fig. 08
02) Connect a DMX-512 light controller to the device’s 3-pin Phoenix terminal DMX connector IN (05)
and connect light fixtures to the device’s 3-pin Phoenix terminal DMX connector OUT (06).
03) Insert the cables correctly.
Fig. 09
04) Put the Phoenix connectors back in the device.
Fig. 10
05) Follow the instructions from 6.4. Recording a Program on page 20.

15
TR-512 Install
Product code: 50826
Program Playing Setup
01) After recording, disconnect power supply from the devices.
02) Disconnect the DMX-512 light controller from the device.
03) Connect the external trigger devices. See 5.3.2.1. Connecting External Trigger Devices on page 16 or
5.3.2.2. Connecting the TR-512 Install-Wall Panel on page 17, for more information.
04) Follow the instructions from 6.5. Playing a Program on page 20.
Fig. 11

16
TR-512 Install
Product code: 50826
Connecting External Trigger Devices
01) Remove the 2-pin 1–6 GPIO Phoenix terminal connectors IN (09).
Fig. 12
02) Connect the desired external trigger devices (movement sensors, temperature sensors, light sensors,
etc.) to the device’s 2-pin 1–6 GPIO Phoenix terminal connectors IN (09).
Fig. 13
03) Optionally, you can connect a 12 V device (e.g. a LED indicator) to the 6th GPIO Phoenix connector.
For example, in Fig. 14, activating trigger 6 will also activate the connected 12 V device.
Fig. 14
04) Put the Phoenix connectors back in the device.

17
TR-512 Install
Product code: 50826
Connecting the TR-512 Install-Wall Panel
You can connect the optional TR-512 Install-Wall Panel (product code: 50827/50828) in order to trigger
programs.
Fig. 15
01) Connect the wall panel to the device with an RJ-45 cable. Recommended maximum cable length:
25 m.
02) Install the wall panel in two ways, with or without the jumper. See Fig. 16.
●With the jumper: Set the TR-512 Install to TOGGLE_TR. See 6.9.4.4. Mode on page 27 for more
information.
●Without the jumper: Set the TR-512 Install to NO_TR. See 6.9.4.4. Mode on page 27 for more
information.
Fig. 16

18
TR-512 Install
Product code: 50826
03) Make sure that the RJ-45 cable has the following pinout:
Fig. 17

19
TR-512 Install
Product code: 50826
6. Operation
Safety Instructions for Operation
Attention
This device must be used only for the purposes it is designed for.
This device is designed to be used as a professional DMX trigger/recorder. It is suitable for indoor
installation in an electrical enclosure. It is not suitable for households.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Attention
Power supply
Before connecting the device to the power supply, make sure that the current, voltage and frequency
match the input voltage, current and frequency specified on the information label on the device.
Start-up
01) Before you power the device, insert the included microSD card into the slot (02).
02) Power the device up. Upon start-up, the device will show the start screen:
03) Press the MENU button to enter the main menu. See 6.9. Main Menu Options on page 23 for more
information.
04) Press and hold down the MENU button for 2 seconds in order to return to the start screen (from any
place in the menu).
Note:
If the display is off, press any button to turn the display on. See 6.9.6.3. Display Option on page 29 for
more information.