SIA PHP601SS User manual

BUILT-IN ELECTRIC HOB
INSTALLA TIONAND OPERATION MANUAL
Please read the instruction manual carefully before operating your new hob.
Dear Owner:
Thank you for purchasing our cooktop which is designed to give you many years of cooking
pleasure. Before using your new appliance please read the user's manual carefully and keep
THIS APPLIANCE MUST BE INSTALLED ONLY BY A QUALIFIED PERSON IN COMPLIANCE
WITH THE INSTRUCTIONS PROVIDED. THE MANUFACTURER DECLINE ALL RESP-
ONSIBILITY FOR IMPROPER INSTALLATION WHICH MAY HARM PERSONS AND ANIMALS
OR CAUSE DAMAGE TO PROPERTY THE APPLIANCE MUST BE USED ONLY FOR THE
PURPOSE FOR WHICH IT WAS EXPRESSLY DESIGNED. ANY OTHER USE (e.g. HEATING
MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE RESULTING FROMND
IMPROPER IRRESPONSIBLE USE.
IMPORTANT NOTICE
Please register your warranty card.
Return the enclosed certificate of guarantee, duly dated and signed.
A duplicate data label and wiring diagram are contained in this booklet.Please attach these labels
to printing or transcription by surface for easy reference.
The Manufacturer shall not be held responsible for any innaccuracies in this handbook due to
printing or transcription errors, also the designs in the figures are purely indicative.
The Manufacturer also reserves the right to make any modifications to the products as may be
considered necessary or useful also in the interests of the user, without jeopardizing the main
functional and safety features of the products themselves.
Warning
1. Please check the built-in electric hob's integrity after opening the package. If there are any
problems please refer to the supplier.
2. Do not throw the package materials (plastic bag, foam, nails, package etc) in a place where
children can easily access. Please dispose of packaging in an environmentally friendly manner.
3. Do not change the wiring under any circumstances.
4.Dispose of the appliance in an environmentally friendly manner.
5.If the power cord is damaged,it must be replaced by a suitably qualified and authorized electrician.
6.The appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of exprence and knowledge.
7.Children should be supervised to ensure that they do not play with the appliance.
Description of the heat plates
Use
Directions and suggestions for using
1.Do not touch the built-in electric hob with wet hands or feet.
2.Do not operate the built-in electric hob when you are bare footed.
3.Do not let young children operate the built-in electric hob.
4.Please disconnect the power supply before you do any maintenance and cleaning.
5.When the built-in electric hob is working ,the temperature of the electric hob and the ambience
become higher, so please do not touch it and keep the children away from it.
6.A steam cleaner must not be used for cleaning the appliance.
it in a safe place for future reference.
ROOMS) IS CONSIDERED TO BE IMPROPER AND CONSEQUENTLY DANGEROUS. THE
Small Electric Plate
Big Electric plate
Swich Knob
Indicate Light
Red Big Electric Plate
7.The appliance is not intended to be operated by means of an external timer or separate
8.The power line should use H05VV-F.
9.The built-in electric hob must be built into a heat resistant cabinet. Some smoking may
occur then first used. Leave on for a short period to burn off excess sealant.
Operation of the top with the electric plates
The electric tops can either be standard, or rapid type.These last feature a red mark at their centre.
According to your needs, the tops can be adjusted by turning the knobs either clockwise,
anti-clockwise on 6 position besides the 0 position (off). The positions marked by the higher
numerical index match the maximum output of heat (see table). When using rapid tops, a
the top operates intermittently to reach a constant cooking temperature. The pilot light set in
the control are a signals that the electric plates are switched on.
The level of heat can be adjusted gradually by turning the appropriate knob to the right or left.
Switching on the plate results in a orange signal light on the control panel turning on.
thermostat auto matically reduces the power when the selected temperature is reached, and
or
remote-control system.
3 Cooking soups ,larger dishes
1 MIN.Warming up
2 Stewing vegetables,slow cooking
4 Slow frying
5-6 Grilling meat,fish
0 Switch off
An appropriately selected pan saves energy.
A pan should have a thick, flat base with a diameter equal to the plate diameter, as in that case
heat is transferred most efficiently.
Advice on the use of cooking tops
To save energy and to have a longer life of the electric tops, we advise using pans with flat
bottom and with a diameter not less than the diameter of the tops.
Care must be taken that fluids do not spill on the electric plates.
Never leave the tops on without pans on them or with empty pans, and never use the tops to
heat the plates. Switch on the plates after having set the pans on them.
Once switched off, the plates remain warm for a while, do not touch.
Switch off the heating element before removing the pans
Technical Data
Model PowerSupply Electric Plate Power(W) Size
Built-in Hole Size
1000
AC220-240V~
50/60Hz 580X 577(L)X477(W)
(145mm)
Small Electric Plate
500X
70
2000
(Red
185mm)
1500
(185mm)
0
1
2
3
4
5
6
Use pans with flat bottoms.Uneven or thin bottoms will waste energy and are slow to cook.
Use pans slightly larger that the hotplates.Smaller pans will waste energy.
Do not use oversized pans.More than 50mm overhang can overheat cooktop components
and can cause fine cracks in the enamel hob which will trap dirt.
Use only dry utensils.Do not place wet or steamy parts (eg.lids) on the hotplates.
Use
Do not use pots and pans that are unsteady and likely to rock or overbalance.
Do not operate the cooktop tor an extended time without utensil on the hotplate.
Good Bad Bad Bad Bad Bad Bad
(recessed base) (convex base) (undersize) (oversize) (moisture on hotplate) (no utensil)
Utensils
Cod: 2
3 4
PHP601SS
PHP601SS

≥750mm
580mm
55
7mm
747 mm
5m00 m
38mm
Ventilation slot
>30mm
Turn off the mains to the equipment before carrying out any maintenance and wait for it cool
Never use abrasive products. Rinse the stainless steel elements with water and
soft cloth. Use sponges or a moist cloth to clean the tops, and remember that water in excess
vinegar. Clean the electric tops using a moist cloth,
warm. Only licensed repairers should service the appliance.
After use, a discolouration of the stainless steel hot plate rims is to be expected and
Appliances with three-pole cable are set up for operation with alternating current at the voltage
the rating plate Look at the connection wiring diagram. The earth
The connection to the electricity supply must be made by a qualified
When the appliance is to be installed above a
Cleaning
elements. Clean tough stains using non abrasive detergents, or warm
Important Notice
This does not effect its operation.
Installation
Electrical connection
down. We advise using lukewarm water and detergents to clean enameled elements. Never
dry using a
can damage the electric
then lightly oil the the top when it is still
cannot be avoided.
and frequency indicated on
conductor is yellow/green.
person and following the regulations in force.
built-in oven, the two appliances must be connected separately.
The supply cable must be so positioned that no point can reach a temperature 50° C higher
Also check that the supply system has an effective earth connection
easily when the appliance is installed.
Fitting guidelines
The voltage rating of the hob heating elements is 220-240V. Adapting the cooker to operate.
to the connection diagram below. The connection diagram is also
connection box. Remember that the connection wire should match the connection type and
The connection cable must be secured in a strain-Relief clamp.
Caution!
Remember to connect the safety circuit to the connection box terminal marked with
cut off in case of emergency. The distance between the working
switch must be at least 3 mm. Before connecting the cooker to the power supply it is
important to read the information on the data plate and the connection diagram.
The manufacturer refuses all responsibility if the standards in force are not respected.
CONNECTION DIAGRAM
Caution! Voltage of heating elements 220-240V
Caution! In the event of any connection the safety
Wire must be connected to the E terminal.
Recommended
type of
connection
lead
For 220-240V earthed one-phase
connection, bridges connect L
terminals and terminals, safety
wire to
N
L
E
H05VV-F3G2.5
N
L
N
than ambient temperature.
and corresponds to the standards in force and that the plug (or omnipolar switch) can be reached
With one - phase current is possible by appropriate bridging in the connection box according
found on the cover of the
the power rating of the cooker.
The electricity supply for the hob must have a safety switch which enables the power to be
contacts of the safety
TECHNICAL INFORMATION FOR INSTALLATION PERSONNEL:
This appliance must be installed only by authorised personnel and in accordance with
of sustaining temperatures of 80 degrees Celsius. All
surfacing materials should be certified suitable for this temperature.Do not instal it in l
the unfire-resistant place (like curtain etc). When you operate, the manufacturer has no
According to the picture as follows, cut the square hole in bench and place the built-in electric
hob in it. Your hob can be fitted to any worktop with a thickness of 40 to 50 mm.
the regulations of Electricity authorities. The wall and bench surfaces must be capable
laminates, fixing adhesive and
responsibility.
Note 1 :
Fire resistant material (eg ceramic tiles) is required to 450
mm above burner top if wall or
vertical structures are not permitted within 200 mm from burner.
Note 2:
No overhanging surface or rangehood and exhaust system
are not permitted within 750 mm
Note 3:
Leave at least 50 mm clearance between the base of the appliance and a combustibile surface.
Never leave the packing components (plastic bags, nails, foamed polystyrene, etc..) within
the reach of the children since they are a source of potential danger.
above burner tops.
MALFUNCTION ELIMINATION
Malfunction Eliminating guide
Electric hob doesn't work Check the connection of wires
Check the fuse and the current limit
There is some smoke
when it is working •
It is normal the first time you use.
•
Clean the drail around the electric hob
and the heating area.
The wire is damaged •Connect the nearest maintainance center to
change the equipment parts.
•
•
•
Symbol Value Unit
Model identification
Type of hob
Number of electric cooking
zones and/or areas
Heating technology (induction
cooking zones and cooking
areas, radiant cooking zones,
solid plates)
For circular cooking zones or
area: diameter of useful surface
area per electric heated cooking
zone, rounded to the nearest 5 mm
For non-circular cooking zones or
areas: length and width of useful
surface area per electric heated
cooking zone or area, rounded to
the nearest 5 mm
Energy consumption per cooking
zone or area calculated per kg
Energy consumption for the
hob calculated per kg
Ø
L, W
--
--
--
--
ECelectric cooking
ECelectric hob
Built-in hob
4
FL: 18,0 cm
N/A
FR: 14.5 cm
FL: 199.5
RR: 194.5
FR/RL: 184.5
RR: 18,0 cm
RL: 14.5 cm
cm
cm
Wh/kg
Wh/kg
190.75
About Erp
Solid plates
5 6
7 8
PHP601SS