SIELINE EF42C User manual

Inset LED Electric Fire
Model No.EF42-45C
INSTALLATION AND OPERATION INSTRUCTIONS
This product is only suitable for well insulated spaces or occasional use.
Please read the instructions carefully before installation or
use and keep for future reference

CONTENTS
1. Important Safety Information··········································································1
2. Technical Specifications ···················································································3
3. Parts and Hardware ·························································································4
4. Appliance Dimensions······················································································5
5. Installation Instructions ···················································································6
6. Operating Instructions ·····················································································8
6a. Manual Control Panel ················································································9
6b. Remote Controls ······················································································11
7. Maintenance ··································································································12
8. Others·············································································································13

1
1. IMPORTANT SAFETY INFORMATION
1.1 Read all of the instructions carefully before using the
appliance.
1.2 For indoor use only. This appliance is not suitable for
use outside the house and only suitable for well
insulated spaces or occasional use.
1.3 Do not use this appliance in the immediate surroundings
of a bath, a shower or a swimming pool.
1.4 Do not use this fire as a free-standing appliance.It must
always be fixed to the fireplace mantel listed in this
manual.
1.5 This fire must not be located immediately below a
socket-outlet.
1.6 This appliance must be earthed.
1.7 This appliance must not be supplied through an external
switching device, such as a timer, or connected to the
circuit that is regularly switched on and off by utility in
order to avoid a hazard due to the inadvertent resetting
of the thermal cut out.
1.8 Keep the power plug accessible after installation
1.9If the power cord is damaged, it must be repaired by the
manufacturer, its authorised service centre or
professional person.
1.10 The meaning of figure in marking is “DO NOT

2
COVER”.Warning: in order to avoid overheating, do
not cover the appliance.
1.11 To reduce the risk of fire, keep textiles, curtains, or any
other flammable material a minimum distance of 1
meter from the air outlet.
1.12 Keep the power cord away from hot surfaces and hot
conditions. Do not route the power lead in front of the
appliance.
1.13 Do not use this fire in rooms that have explosive gas in
them (for example petrol), or if you are using solvents,
glue, aerosol spray or in flammable paints, as these may
catch fire.
1.14 Children shall not play with the appliance.
1.15 Children of less than 3 years should be kept away unless
continuously supervised.
1.16 Cleaning and user maintenance shall not be made by
children.
1.17 Children aged from 3 years and less than 8 years shall
not plug in, regulate and clean the appliance or perform
user maintenance.
1.18 Children aged from 3 years and less than 8 years only
can switch on/off the appliance provided that it has
been placed or installed in its intended normal
operating position and instructions and supervisions
concerning the safe way of the use of the appliance are
offered.

3
1.19 This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
1.20 Do not use this appliance in small rooms when they are
occupied by persons not capable of leaving the room on
their own, unless constant supervision is provided.
1.21 Caution: some part of this appliance can become very
hot and cause burns. Particular attention has to be
given where children and vulnerable people are present.
1.22 Do not use this heater if it has been dropped.
1.23 Do not use if there are visible signs of damage to the
appliance.
2. TECHNICAL SPECIFICATIONS
Model No.: EF42-45C
Supply Voltage: AC 220-240V 50Hz
Maximum power consumption: 2KW
Power for flame effect: 6W (LED 2W + Motor for flame 4W)
Heat Output:
Nominal heat output (Pnom): 2KW
Minimum heat output(indicative) (Pmin): 1KW
Maximum continuous heat output (Pmax): 2KW
Auxiliary Electricity Consumption:
At nominal heat output (elmax): 12.5W
At minimum heat output (elmin): 12.0W
In standby mode (elSB): 0W

4
Type of heat output / room temperature control
Single stage heat output and no room temperature control
No
Two or more manual stages, no room temperature control
No
With mechanic thermostat room temperature control
No
With electronic room temperature control
Yes
Electronic room temperature control plus day timer
No
Electronic room temperature control plus week timer
No
Other Control Options
Room temperature control, with presence detection
No
Room temperature control, with open window detection
No
With distance control option
No
With adaptive start control
No
With working time limitation
No
With black bulb sensor
No
3. PARTS AND HARDWARE
3.1 Unpacking the fire carefully, make sure that the appliance is intact with no
signs of damage caused by transport and no part has been exposed to water.
If in doubt, do not use the appliance and contact an authorised service centre.
3.2 Keep plastic wrapping away from children.
3.3 Save the original packaging as this may be required in the event of service
complaint with product.
3.4 Check that all parts are removed from the packing.
Firebox (1)
Remote control
(1)
Instruction (1)
Battery (1)

5
4. APPLIANCE DIMENSIONS
Units: mm
Model
A
B
C
D
E
F
G
H
EF42C
630
582
556
430
545
509
223
198
EF43C
710
660
640
508
625
589
223
198
EF44C
810
760
737
608
625
589
223
198
EF45C
890
840
820
688
685
649
223
198
Unit: mm

6
5. INSTALLATION INSTRUCTIONS
ALWAYS unplug this fireplace heater before assembly or
cleaning, or before relocating. Failure to do so could result in
electric shock, fire, or personal injury.
KEEP drapery and other furnishings at least 0.9m from the
front and sides of the electric fireplace.
AFTER installation, ensure that there is ≥0.004 ㎡ventilation
area between inside and outside of fireplace mantel.
1) Locating the Appliance
Your new electric fireplace may be installed virtually anywhere in your home.
However, when choosing a location, ensure that the general instructions for
safety are followed.
•For best results, install out of direct sunlight, water or very damp air.
•Power supply service must be installed within proximity of electric fireplace
prior to finishing avoiding reconstruction.
2) Locate an outlet
•Plug in (you may run the power cord out of the framed wall opening to an
existing outlet or install an outlet on a nearby wall stud within the wall).
•Make sure the outlet is in good condition and that the plug is not loose.
NEVER exceed the maximum amperage for the circuit. DO NOT plug other
appliances into the same circuit.
3) Recessed into a wall
It is available to install the unit into a wall. The opening depth 206mm is
suggested for better ventilation. Build the opening according to the suggested
specification shown below.

7
Opening sizes ranges/mm
SKU
Width
Height
Depth (min)
Depth (suggest)
EF42C
556-607
510-541
198
205
EF43C
640-690
590-620
EF44C
740-790
590-620
EF45C
820-871
650-675
Prepare the opening and outlet, place the unit into the framed
opening gently and no fixing brackets are needed.
Note: If the existing opening is found a little bit narrow, the handles
on both sides could be removed.

8
4) Insert into a cabinet or wood mantel.
It is available to install the unit into a wood cabinet or mantel.
Also, it would be better to keep the depth at 205mm.
The clearance from the top of the unit to the bottom of TV or something else
sitting on the cabinet should be 203mm at least.
When moving the insert into a mantel, DO NOT let bottom of
insert touch the mantel to avoid scratches.
6. OPERATING INSTRUCTIONS
WARNING! Do not operate the appliance if it is damaged or has malfunctioned.
If you suspect the appliance is damaged or has malfunctioned call a qualified
service engineer to inspect the appliance, and replace any part of the electrical
system if necessary, before reuse.
WARNING! To reduce the risk of fire, keep textiles, curtains, or any other
flammable material a minimum distance of 1 meter from the air outlet.
MAKE SURE the plug fits tight in the outlet. Faulty wall outlet connections or
loose plugs can cause the outlet to overheat.
Do not disconnect the power at the mains supply whilst the appliance is running.
Use the functions on the remote to turn the fire off and ensure the mains switch
has been moved to the off position before disconnecting.
PREPARATION BEFORE USE

9
6.1 The appliance can be operated by both remote control and the manual
controls on the appliance.
NOTE: To use both remote and manual functions the manual on/off switch
must be in ‘ON’ position. In order to prevent the product becoming too hot,
there is 10s delay when turning on the heater and a 10s delay when turning off
the heater fan.
Batteries
Ensure that the handset batteries are new and inserted correctly.
Main Power Switch
6.2 The mains power switch is located on the control panel located on the right-
hand side of the heater box.
6.3 Switch ON (—) before operating either the remote or manual controls.
6.4 A long beep is heard to indicate the fire is ready for use.
6a. MANUAL CONTROL PANEL
Note: When the heater is first turned on, a slight odor may be present.
This is normal and should not occur again unless the heater is not
used for a long period of time.

10
BUTTON
NAME
FUNCTION
POWER
SWITCH
Turn the main power switch on. A long
“beep” sound will be heard when the
switch is turned at ON Position “I”.
Note: The remote control will lost the
memory for function settings when the
switch is turned at OFF Position “O”.
FLAME
The flame will be cycled from Flame A –
Flame B –Flame C –Flame D –Flame E –
Flame Off.
HEATER
The heater will be cycled from Low –High
–Heater Off. The indicator light on left to
Power Switch (see the right picture on
last page) will illuminate when the heater
is turned on. The indicator light will go
out within 10s.
Low: (●○)
High: (●●)
Note:
Heater can be used without flame.
The heater will work when the
temperature set by thermostat is higher
than room temperature.
The Fan works about 10s ahead of the
heater, and stops about 10s later than
the heater.
The indicator light in the lower fuel bed
(see the left picture on last page) always
illuminates when heater is on.

11
5
4
3
2
1
9
6
7
8
THERMOSTAT
Turn it to setting 9 first and when the
room has reached a desired level, turn
the rotary switch counterclockwise slowly
until the thermostat just ‘clicks’ off. The
thermostat will then maintain the room
at this selected level. To increase the
temperature, turn the rotary switch
clockwise to a higher setting. From 1-9,
this corresponds to the room
temperature at 9-34℃.
6b. REMOTE CONTROLS
BUTTON
TITLE
FUNCTION
POWER
The power button will put the unit in
standby mode. This will turn off all
functions and hold the settings in memory,
press the power button again will turn on
the unit to previous settings.
For the first time use, Flame A will be
turned on.

12
FLAME
The flame will be cycled from Flame A –
Flame B –Flame C –Flame Off.
LOW HEAT
To turn on the heater on half heat setting or
turn off the heater.
HIGH HEAT
To turn on the heater on full heat setting or
turn off the heater.
CRACKLING
To turn on the crackling and cycle through
high crackling sound –normal crackling
sound –low cracking sound - high crackling
with wind sound –normal crackling with
wind sound –low crackling with wind
sound- off.
7. MAINTENANCE
WARNING: Before any maintenance or cleaning of the exterior of the fireplace,
the unit should be disconnected from the power supply until it is cool off.
7.1 Remote Handset Battery Replacement
Replace with 1 x CR2032 Lithium lon button cell battery. Make sure the battery is
installed correctly in the remote control.
7.2 Maintenance of Motors
The motors used on the fan and flame effect are pre-lubricated for extended
bearing life and require no further lubrication. However, periodic
cleaning/vacuuming of the fan/heater unit is recommended.
7.3 Cleaning the Fireplace
You can clean the exterior of the fireplace with a soft, damp, lint-free cloth. Do
not use cleaning or polishing products. To remove fingerprints or other marks on
the front glass panel, use a soft, damp, lint-free cloth with a good quality

13
household glass cleaner. The front glass panel should always be completely dried
with a clean, lint-free cloth or paper towel.
CAUTION: Abrasive cleaners should not be used on the glass panel. Liquids
should not be sprayed directly onto any surface of the unit.
8. Others
Environment
Meaning of crossed –out wheeled dustbin:
Electrical appliances should not be disposed as unsorted municipal
waste. Separate collection facilities should be used in the disposal
of electrical appliances. Contact your local government for the
information about the available collection systems. If electrical
appliances are disposed of in landfills or dumps, hazardous
substances can leak into the groundwater and get into the food chain, damaging
your health and well-being. When old appliances are replaced by the new ones, it
is a legal oblige for the retailer to take back the old appliance for disposals at
least free of charge.
This fire complies with Regulation (EU) 2015/1186, the Safety
Standards EN 60335-1 and EN 60335-2-30 which covers the
essential requirements of the Low Voltage Directive 2014/35/EU
and the EMC standards EN 55014-1; EN 55014-2; EN 61000-3-2 and EN 61000-3-3
which covers the essential requirements of the European Electro Magnetic
Compatibility 2014/30/EU.