SIST&MATICA Easy Operating instructions

SIST&MATICA Srl
SIST&MATICA SrlSIST&MATICA Srl
SIST&MATICA Srl Pag. 1
Via S. Pertini, 17 - 12030 MANTA (CN) ITALY Tel. [phone] r.a. - Fax [phone]
http://www.sistematica.it e-mail: [e-mail]
…RADIO REMOTE CONTROL TRANSMITTERS
USER AND MAINTENANCE MANUAL
WARNINGS
This manual is an essential part of the device and it should be thoroughly kept for later consultation.
Carefully read the warnings contained in this manual, concerning safety and a proper preservation of the
product. These warnings are ALWAYS to be carefully read before using the device. SIST&MATICA S.r.l.
declines all responsibility for any trouble arising from the non-compliance with these warnings.
•AVOID ATTEMPTING TO REPAIR THE DEVICE BY YOURSELF. REPAIRS PERFORMED BY
UNSKILLED PEOPLE CAN CAUSE SERIOUS DAMAGES OR FAILURES. FOR ASSISTANCE,
APPLY TO YOUR LOCAL AUTHORIZED SERVICE CENTRE. USE ONLY ORIGINAL SPARE PARTS.
•ALWAYS KEEP AT A SAFE DISTANCE FROM THE MOVING PARTS.
•KEEP THE RADIO CONTROL OUT OF THE CHILDREN’S REACH.

SIST&MATICA Srl
SIST&MATICA SrlSIST&MATICA Srl
SIST&MATICA Srl Pag. 2
Via S. Pertini, 17 - 12030 MANTA (CN) ITALY Tel. [phone] r.a. - Fax [phone]
http://www.sistematica.it e-mail: [e-mail]
TECHNICAL FEATURES
•Working frequency 433.92 MHz;
•Battery supply (no. 2 "AAA" 1,5V Cell, Alkaline
Batteries)
•Transmission average absorption < 5 mA
•Quiescent absorption < 0.2 uA
•Average batteries life: 8 mths
•Light signals to indicate controls transmission and
low battery
•IP 67 protected, oil, diluted alkali and acids proof
keypad
•Up to 4 control functions
•Response time after a button push: <35 ms
•Emergency stop function response time (stop
button): <35 ms
•Working temperature: -20°C to + 70°C
•Transmitter weight (batteries included): 55 gr.
•Working distance in open spaces: 80 m.- 260 ft
(with fresh batteries)
•Size (in mm): 96 x 47 x 24
INSTRUCTIONS FOR USE
1. Switch the receiver on (emergency stop button
released)
2. Wait for a few seconds (self-testing)
3. Press START to allow the system to receive the
transmission (the system stays active for n. 2
minutes after the last control has been given, after
which it resets. Then press START again to
restart the system)
4. Press the required key on the transmitter to
activate the related output on the receiver.
Ex. KEY 1→OUT 1 + RELAY MOTOR
5. Press the STOP key to inhibit the controls
reception. In this phase all the controls are reset.
To activate again the system press START
LED INDICATED ON THE RADIO TRANSMITTER
REGULAR FUNCTIONING
While functioning regularly, the LED flashes when any
key is pressed.
LOW BATTERY
When the battery is low, the LED keeps flashing as far
as a key is pressed. At this point, the system will
function for a few more time: replace with new
batteries (see “TRANSMITTER’S BATTERIES
REPLACEMENT”).
Do not leave flat batteries inside the transmitter
SYSTEM CODING
It is necessary to code the system only if you have to
replace the transmitter unit or if you want to use it with
a different receiver from the one it was purchased with.
To recode the system refer to the receiver user
manual

SIST&MATICA Srl
SIST&MATICA SrlSIST&MATICA Srl
SIST&MATICA Srl Pag. 3
Via S. Pertini, 17 - 12030 MANTA (CN) ITALY Tel. [phone] r.a. - Fax [phone]
http://www.sistematica.it e-mail: [e-mail]
TRANSMITTER’S BATTERIES REPLACEMENT
Due to the electronical microelements of the radio control transmitter, carefully handle the under described
operations in a clean environment.
1. Use n. 2 “AAA” 1,5 V type alkaline batteries
(due to the low radio control transmitter
consumption it is not advisable to use carbon zinc
batteries as they can undergo self-discharge more
rapidly than alkaline ones. Do not use
rechargeable batteries)
2. Open the transmitter case by screwing the screw
located on its back, as the arrow indicates in the
above picture;
3. Open the transmitter:
the keypad is connected to the lower part of the
transmitter by a flexible conductor: handle it
carefully to avoid it to come out;
4. Turn the keypad cover of 90°
5. Unscrew the screw that keeps the batteries
locked, as the arrows indicates in the above
picture, and take it off (see the following picture)

SIST&MATICA Srl
SIST&MATICA SrlSIST&MATICA Srl
SIST&MATICA Srl Pag. 4
Via S. Pertini, 17 - 12030 MANTA (CN) ITALY Tel. [phone] r.a. - Fax [phone]
http://www.sistematica.it e-mail: [e-mail]
6. Take the discharged batteries off. 7. Put the new batteries in, taking care of the polarity
indicated next to every contact. Before closing the
battery case, check that the LED flashes when
any key is pressed and released on the
transmitter. If this should not happen, check the
correct positioning of the batteries.
8. Close the battery case by following backwards the
instructions given.
TROUBLESHOOTING AND SOLUTIONS
PROBLEM
P OSSIBLE C AUSE S OLUTION
The led on the radio control transmitter
does not flash when pressing any key Flat battery Replace the radio control transmitter battery
The system does not react to any
command Flat battery Replace the radio control transmitter battery
The system does not react to any
command Wrong replacement of the batteries Check the correct batteries positioning
The system does not react to any
command System coding loss Code again the system following the instructions related only to the correspondent receiver’s coding.
The system reacts to any command in a
not continuous way Flat battery Replace the radio control transmitter battery
The system reacts to any command in a
not continuous way Transmission out of the radio control transmitter range Keep at a distance ≤80m from the receiver
“Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment”.