SkyHopper PRO V User manual

1

2
www.skyhopper.biz
[e-mail]
Specifications may be subject to change at any time.

3
Notice
This manual contains information that is proprietary to Mobilicom Ltd.
No part of this publication may be reproduced in any form whatsoever without prior written approval by Mobilicom.
License Terms
Mobilicom hereby grants a non-exclusive, nontransferable worldwide license to the licensee of this software product to use
the SkyHopper PRO V Graphical User Interface (GUI), in object code only for the sole and internal purpose of configuring,
monitoring and managing Mobilicom’s SkyHopper PRO V.
Warranty
Mobilicom does not warrant that this software product is free from errors and/or will run properly on all computer
hardware and/or operating systems. Mobilicom does not warrant that this software will operate in the combinations that
may be selected for use by end users or that the operation of this software product will be uninterrupted or error free.
Limitation of Liability
Mobilicom’s cumulative liability to you or any other party for any loss or damage resulting from any claims, demands, or
actions arising out of, or relating to, this agreement and the Web GUI shall not exceed the sum paid to Mobilicom for the
purchase of the Web GUI. In no event shall Mobilicom be liable for any indirect, incidental, consequential, special or
exemplary damages or lost profits, even if Mobilicom has been advised of the possibility of such damages.
This agreement shall be construed and governed in accordance with the laws of the State of Israel.

4
Contents
1. Abbreviation List
6
2. Overview
8
2.1 Network Topologies & Applications
8
2.1.1 Point-to-Point
8
2.2 SkyHopper PRO V Main Features
9
2.3 Packets Supported by the SkyHopper PRO V Network
9
3. Physical Description
10
3.1 Front View Connectors
10
3.2 Unit Cables: Types & Usage
10
4. Mechanical Specifications
11
5. Technical Specifications
11
5.1 Radio & Modem Specifications
11
5.1.1 Frequency Bands Available
11
5.1.2 Antennas
11
5.1.3 RF Characteristics
11
5.2 Power Specifications
12
5.3 Environmental Specifications
12
5.4 Embedded GPS Characteristics
12
6. TDMA
13
7. Point-to-Point (PTP)
13
7.1 PTP Link Step-by-Step Configuration
14
7.2 SkyHopper PRO V LED Indicator
15
8. Video Configuration
16
8.2 Video Information
16
8.3 Video Encoder
18
8.4 Video Decoder
21
9. Installation & Setup
22
9.1 Package Contents
22
9.2 Connecting the Antennas
22
9.4 Connecting the Power
22
Appendix A –Specifications
23
Appendix B –Mechanical Drawings
25
Appendix C –Connector Pinouts
26
C.1 RS232 / 1PPS
26
C.2 Power Cable
26
Appendix D –Setting Up a Pixhawk Based System
28
D.1 SkyHopper Setup
28
D.2 Physical Connection
28
D.3 UART-to-Ethernet
29
Appendix E –Troubleshooting
30

5
List of Figures
s
8
Figure 2: Asymmetric Link Configuration
8
Figure 3: SkyHopper PRO V Front View
10
Figure 4: SkyHopper PRO V Connector Side View
10
Figure 5: Transmit Frames of the Remote unit & Controller unit from Power Up
14
Figure 6: Web GUI Main Screen
14
Figure 7: Web GUI Advanced Configuration Screen
15
Figure 8: Web GUI Video Information Screen
17
Figure 9: Web GUI Video Screen of the Encoder
18
Figure 10: Web GUI Video Screen of the Decoder
21
Figure 11: RS232 / 1PPS Connector (IOIOI) (SkyHopper PRO V Side)
26
Figure 12: Power Connector (SkyHopper PRO V Side)
26
Figure 13: Web GUI Advanced Configuration
28
List of Tables
Table 1: Abbreviation List
6-7
Table 2: SkyHopper PRO V Mechanical Specifications
11
Table 3: SkyHopper PRO V Power Specifications
12
Table 4: SkyHopper PRO V Environmental Specifications
12
Table 5: Embedded GPS Characteristics of SkyHopper PRO V
13
Table 6: Video Stream Connection Options
19
Table 7: RS232 / 1PPS Connector Pinout (IOIOI)
26
Table 8: PWR Connector Type & Pin Mapping
27

User Manual
6
1. Abbreviation List
Abbreviation
Syntax
BPS
Bits Per Second
BW
Bandwidth
CEP
Circular Error Probable (Accuracy)
CINR
Carrier to Interference and Noise Ratio (Signal to Noise Ratio)
CPLD
Complex Programmable Logic Device
CRC
Cyclic Redundancy Code
dB
Decibel
dBm
Power ratio in decibels of the measured power referenced to one mill watt
CDD
Cyclic Delay Diversity
Controller Unit
A SkyHopper PRO V Unit, in PTP setup, which acts as an endpoint communication unit. Typically a Ground
Unit.
CTC
Convolutional Turbo Code
DC
Direct Current
EMI
Electromagnetic Interference
ETH
Ethernet
ETSI
European Telecommunication Standard Institute
FAE
Field Application Engineer
FCC
Federal Communications Commission
FEC
Forward Error Correction
FFT
Fast Fourier Transform
FPS
Frame Per Second
Freq.
Frequency
FW
Firmware
GHz
Gigahertz
GPS
Global Positioning System
HD
High Definition (Video)
HW
Hardware
ID
Identification (Number)
IP
Internet Protocol
LAN
Local Area Network
LAT
Latitude
LED
Light Emitting Diode
LON
Longitude
LOS
Line-Of-Sight

User Manual
7
Abbreviation List, Cont’d.
mW
Milliwatt
MHz
Megahertz
MIMO
Multiple-In-Multiple-Out
MRC
Maximal Ratio Combining
N.C.
Not Connected
OEM
Original Equipment Manufacturer
OFDM
Orthogonal Frequency Division Modulation
OS
Operating System
OSD
On Screen Display
PC
Personal Computer
PPS
Pulse Per Second
PTP
Point-To-Point
PTMP
Point-To-Multipoint
QAM
Quadrature Amplitude Modulation
QPSK
Quadrature Phase Shift Keying (modulation)
Remote Unit
A SkyHopper PRO V unit, in PTP setup, which acts as an endpoint communication unit that distributes clocks
in the system. Typically the Aerial Unit.
RF
Radio Frequency
RMS
Root Mean Square (Average)
RSSI
Receiver Signal Strength Indication
Rx
Receive
SBAS
Satellite Based Augmentation System
SDR
Software Defined Radio
SW
Software
TDD
Time Division Duplexing
TDMA
Time Division Multiple Access
Tx
Transmit
UAV
Unmanned Aerial Vehicle
UGV
Unmanned Ground Vehicle
VLAN
Virtual LAN
VPN
Virtual Private Network
Table 1: Abbreviation List

User Manual
8
2. Overview
SkyHopper PRO V offers a bi-directional Data Link enabling video processing & analytics, with a built-in video encoder /
decoder. Furthermore, SkyHopper PRO V contains 3 camera interfaces –HDMI, Analog, and IP, and contains a dual camera
input for a simultaneous connection to two cameras. SkyHopper PRO V offers real-time Full HD video at a glass-to-glass low
latency. It is specifically designed for commercial and industrial drones, and provides the best solution for fleet management
and autonomous UAV systems.
By employing leading wireless technologies, SkyHopper PRO V delivers long range and Non-Line of Sight (N-LOS)
communication that supports broadcast, multicast and unicast transmission modes. SkyHopper PRO V supports Point-to-
Point and Point-to-Multipoint communication, thereby enabling various modes of operation such as communication for
multi-drone operations and drone communication to multiple ground units and viewers (receivers).
An additional benefit of your SkyHopper PRO V is that it offers Control, Telemetry and Payload all in one RF channel. No need
for separate solutions for each, no need for excess items to weigh down your drone.
Figure 1: SkyHopper PRO V
2.1. Network Topologies & Applications
2.1.1. Point-to-Point (PTP)
A Point-to-Point system includes 2 units, with the bandwidth ratio between the two units configurable according to
the application. It can be symmetric when a full duplex communication is required (50% to each unit) or asymmetric
up to 10% to one unit (Controller or Remote Unit) and 90% to the other unit (i.e. drone/robot that transmits video to
the ground/controller unit and that controls the camera).
Below is an example of an asymmetric link: 6Mbps configuration, where 10% of available BW is allocated for uplink
and 90% is allocated for downlink.
Figure 2: Asymmetric Link Configuration

User Manual
9
2.2. SkyHopper PRO V Main Features
SkyHopper PRO V offers the following features to take your drone to new levels:
SkyHopper PRO V is equipped with two camera inputs, allowing for the simultaneous connectivity of two
separate cameras simultaneously
Real-time full HD wirelessly over the air at a Glass-to-Glass low latency
HDMI, Analog and IP camera interfaces
Tremendous transmission range that can exceed 5km line-of-sight
Relay operation for extending long range line-of-sight and overcoming dead spots in urban or industrial areas
Non-line-of-sight (NLOS) communication by using a proprietary technology to provide a robust and clear radio
signal
Allows for a number of control stations with the same functionality to control the same drone simultaneously
with seamless handover between control stations
Supports drone communication to multiple control stations and an unlimited number of viewers (receivers)
Robust security and encryption mechanisms to protect your data from potential cyberattacks
Local recording ability directly onto the drone. Can be performed simultaneously during real-time streaming
Software Defined Radio (SDR) mobile technology
Full 2-Channel MIMO
Scalable solution from a Point-to-Point to a Point-to-Multipoint network with relays
High mobility with continuous transmissions up to 800km/h
Mobile broadband network
Small physical dimensions and very lightweight (105 gr) (portable device)
Low power consumption (10W average)
2.3. Packets Supported by the SkyHopper PRO V Network
The SkyHopper PRO V physical link supports Ethernet (IEEE 802.3) which includes:
TCP/IP and UDP/IP real-time applications using RT Protocols such as: VoIP for voice, RTSP or UDP for Video and
Data, etc.
Broadcast, Multicast, Unicast
Any Ethernet packet received by the unit’s Ethernet port is encapsulated internally with a standard frame for
transmitting via the Data Link to the remote unit. The remote unit recovers the original Ethernet packet and forwards
it to the Ethernet port.
NOTE –The unit is similar to an Ethernet layer 1 (physical layer), which makes integration with your
equipment nothing more than connecting the Ethernet cable.

User Manual
10
3. Physical Description
3.1. Front View Connectors
RF1: Antenna 1 Connector, MMCX/F 50 Ohm
RF2: Antenna 2 Connector, MMCX/F 50 Ohm
GPS: GPS Antenna Connector, MMCX/F
Figure 3: SkyHopper PRO V Front View
3.2. Unit Cables: Types & Usage
Ethernet: Standard RJ45 connector
Serial (IOIOI):
Molex - 502380-0600
RS232 / 1PPS connector
Power:
ZE - ZER-04V-S
Power connectors utilizing 7-14.5VDC
CAUTION: When SkyHopper PRO V is carried by a person, environment temperature should not exceed 45°C
(113°F)
NOTE –Information about the connectors’ pin assignments are available in Appendix C – Connectors Pinout
LED: SkyHopper PRO V’s LEDs indicate power on, data transmission and link status.
Figure 4: SkyHopper PRO V Connector Side view

User Manual
11
4. Mechanical Specifications
The SkyHopper PRO V unit is lightweight and has small form-factor.
Dimensions
[HxWxD] (mm)
[HxWxD] (inch)
Weight (gr)
Weight (oz.)
31 x 54 x 74
1.2 x 2.1 x 2.9
131
4.62
Table 2: SkyHopper PRO V Mechanical Specifications
5. Technical Specifications
5.1. Radio & Modem Specifications
5.1.1. Frequency Bands Available
2.4GHz unlicensed band.
Commercial licensing support is available.
Note: This product is configured to operate within the FCC, CE and TELEC limitations based on the country of
ordering. It is configured within the 2.4 ISM frequency band. Mobilicom takes no responsibility should you
choose to take and/or operate this product outside of FCC, CE or TELEC limits and/or in a country that does
not comply with FCC, CE or TELEC regulations. Please note that SkyHopper specifications vary based on FCC,
CE and TELEC regulations.
5.1.2. Antennas
Equivalent antennas must be of the same type, must be of equal or lesser gain than an antenna previously authorized
under the same grant of certification (FCC ID), and must have similar in-band and out-of-band characteristics (consult
specification sheet for cutoff frequencies).
5.1.3. RF Characteristics
Peak output power: 2 x 0.5W per channel
Average output power: 2 x 100mW per channel (20dBm)
Noise Figure: 5dBm
Radio Access Method: OFDM - TDMA
Configuration & Diversity Support: 2X2 MIMO with MRC(RX) and CDD(TX)
Frequency Resolution: 0.25MHz
Channel bandwidth: Configurable 4.2/8.4MHz
FFT Supported: 512
Guard band: 64 sub-carries on each side
Total subcarriers used per symbol: 384
Data carriers used: 336
Pilot carriers used: 48
Sub carrier spacing: 13KHz for 5MHz bandwidth with 5msec frame
Modulations: QPSK, optional 16QAM
FEC methods: CTC
FEC Ratios: ¾ , ½ , ¼
Error Detection: CRC32
Full TDD asymmetrical duplexing
Flexible ratio from 1:1 to 1:9 in PTP
Resolution of 1% between all units in multi-unit networks.

User Manual
12
NOTE –The wide configurable power control range enables transmitting in low Tx power when not
needed, thereby reducing power consumption.
5.2. Power Specifications
SkyHopper PRO V is designed to be battery operated (DC) with low power consumption. Its design allows for multiple
battery cell configurations (different voltages).
Power - LF10WBRB-4P
DC Voltage (Battery Operated)
7-26VDC
Power Consumption
10 Watts average use
Up to 12 Watts depending on the operational scenario (Tx:Rx Ratio)
Table 3: SkyHopper PRO V Power Specifications
5.3. Environmental Specifications
SkyHopper PRO V is designed to meet international EMI, Radio & Environmental Standards, such as FCC, TELEC and
CE.
Environmental
Temperature Range
Operating
Storage
-10°C to 45°C
-50°C to 85°C
Humidity
5 to 95%
Table 4: SkyHopper PRO V Environmental Specifications
5.4. Embedded GPS Characteristics
SkyHopper PRO V has a built-in GPS receiver. In a PTP network configuration it is used for location information only
(which can be operated by the customer via the SkyHopper API). In a Multi-Unit network, it is used for synchronization
and can also be used by the customer for location purposes. SkyHopper PRO V uses active GPS antennas. The power
for the active antenna is provided by the unit via the regular GPS MMCX connector.
Item
Description

User Manual
13
Receiver Type
GPS L1 C/A code
Accuracy
Position 2.5 m CEP
SBAS 2.0 m CEP
Acquisition
Cold start: 27 s
Aided start: < 3 s
Hot start: 1 s
Sensitivity
Tracking: –161 dBm
Cold start: –147 dBm
Hit start: –156 dBm
Timing Accuracy
RMS 30 ns
99% < 60 ns
Granularity 21 ns
Table 5: Embedded GPS Characteristics of SkyHopper PRO V
6. TMDA
Time Division Multiple Access (TDMA) is a channel access method for shared medium networks. It allows several units to
share the same frequency channel by dividing the signal into different time slots. The units transmit and receive on the same
frequency in a synchronized manner. Every unit transmits in its own dedicated time slots. On the other time slots said unit
receives the transmission sent by the other units that are members of the same network (which are also transmitting on their
own dedicated slots).
TDMA requires a synchronization system. The system is synchronized internally, externally or via GPS (synchronization varies
between topologies and method used).
The SkyHopper PRO V unit uses TDMA regardless of the application type, PTP or PTMP.
7. Point-to-Point (PTP)
A PTP network is a radio link between 2 SkyHopper PRO V units. The configuration (frequency and profile) of both units must
be the same with only one difference - one unit is configured as a Remote Unit while the other unit is configured as a
Controller Unit.
The Remote Unit works with its internal clock and synchronizes the Controller Unit. After power-up, the Remote Unit starts
transmitting regardless of link status. The Controller Unit however, does not transmit and stays in Rx mode, trying to acquire
synchronization by finding a preamble (synchronization pattern). As soon as the Controller Unit recognizes the pattern, it
starts to transmit according to its allocated time slot.
The transmission bandwidth ratio is predefined as part of the profile configuration as asymmetric up to 10% to one unit
(remote or controller) and 90% to the other unit.

User Manual
14
Figure 5: Transmit frames of the remote unit and controller unit from Power Up
Note: A viewer unit acts like a Controller unit but with one major change, it does not transmit
and only receives.
7.1. PTP Link Step-by-Step Configuration
In order to build a PTP link, two SkyHopper PRO V units are required. One unit acts as a remote unit, while the other
as a controller unit.
1. Connect antennas to RF1 and RF2 connectors, and power up the unit.
! CAUTION –Powering up a unit without connecting the antennas can cause irreparable damage to the unit.
2. Connect the unit to a PC using a standard Ethernet Cat 5 cable.
3. Set static IP in the 192.168.131.xxx subnet (For more information, see the Web GUI Instructional Manual).
4. Using the Web GUI: Open a web browser installed on your PC / laptop (Chrome, Firefox, Internet Explorer, etc.)
and input in the address line: 192.168.131.241. That should connect you to the Web GUI interface, as shown on
Figure 6:
Figure 6: Web GUI main screen
5. To change the frequency to the required frequency, click on “Advanced Configuration” (third tab on the left
corner) and on the “Frequency” line write the desired frequency within the frequency range set in your unit.

User Manual
15
6. Set the profile as required (RF bandwidth, bitrate and ratio) and click on the “Apply” button as shown on Figure
7. The unit will reboot.
7. Repeat stages 1-4 with the 2nd unit.
Figure 7: Web GUI “Advanced configuration” screen
NOTE –A PTP setup requires 2 SkyHopper PRO V units configured with same frequency and profile.
7.2. SkyHopper PRO V LED Indicator
By following the LED on the unit, the power and link status can be monitored. It is described as follows:
ACTV LED:
oOff –Power Down
oOn - Booting Up
oSlow Blinking –Remote unit is transmitting, controller unit receiving (P2P search)
oFast Blinking –Air Link is up
DATA LED
oOff –No Ethernet detected
oOn –Ethernet Cable is connected to a working device on host –No Data
oSlow Blink –Error (synced to ACTV LED)
oFast Blink –Tx & Rx Air Traffic active
Should there be an error in your SkyHopper PRO V unit, both the ACTV and DATA LEDs will be simultaneously slow
blinking.
Link status, CINR, RSSI, throughput and unit log information is available in the Web GUI, which can be found online at
www.skyhopper.biz/skyhopper-pro-v#support.
8. Video Configuration

User Manual
16
SkyHopper PRO V has 3 camera connection interfaces:
1. HDMI Digital
2. Analog
3. IP
The HDMI camera connects to the HDMI input port of SkyHopper PRO V; the analog camera connects to the supplied RCA cable,
which then connects to the analog port; and the IP camera connects to Ethernet port.
Please note: The “Video” sessions are for HDMI and analog cameras only.
Each SkyHopper PRO V unit can be configured as “Remote” or “Controller”. Depending on the configuration, the “Video” screen
will be adjusted accordingly. If the unit will be defined as “Remote”, the “Video” screen will be adjusted to a video encoder
configuration, and if the unit will be defined as “Controller”, the “Video” screen will be adjusted to a video decoder configuration.
In the encoder mode, the cameras are inputs and in decoder mode, a display screen is connected.
There are two ways to receive a decoded stream:
1. Hardware decoder –If the user has 2 SkyHopper PRO V units, the one that is defined as a “Controller” will also
be defined as decoder, thus it will decode video streams using the hardware. The advantage of using hardware
to decode the video stream/s, is that better latency performance will be achieved than when using software
decoder. Please refer to the Web GUI Instructional Manual for more information.
2. Software decoder –If the user decides to use a proper video player, he can avoid using SkyHopper PRO V as a
decoder, and receive the video streams directly to his PC / laptop / tablet. The main disadvantage with this
method is that the user must have a good video player with low latency, but regardless, using this method will
not yield the same latency performance as with hardware decoder. Please refer to the IP Connection Guide for
more information.
8.1. Video Information
Video Information is a separate screen in the SkyHopper PRO VV Web GUI. This screen shows actual camera
definitions that are connected to (and powered by) a SkyHopper PRO V unit and also shows the SD card status (if
present), as shown by the example in Figure 8:
NOTE –The SD card has a 32 GB size limit.

User Manual
17
Figure 8: Web GUI “Video Information” screen
NOTE –This screen will be functional only when a SkyHopper PRO V unit will be set as a “Remote” unit. This is
due to the fact that a camera may not be connected directly to the decoder because a video stream from said
camera must first be encoded, and only then may it be decoded on the other side.
The HDMI and Analog rows show camera type status, if one is connected to the “Remote” unit. The “Camera
Detected” field shows whether an HDMI / Analog camera was detected, “NTSC/PAL” shows the camera video
encoding system. The “FPS” (Frame per Second) field shows the number of frames detected. The “Status” field shows
the camera’s readiness (it MUST be “locked” to obtain a video stream). The “Interlace/Progressive” field shows the
video scanning method. In the “SD Card” section, “Inserted” shows if there is an SD card present or not, and
“Recording” shows if there is a video stream recording on the SD card.

User Manual
18
8.2. Video Encoder
To set a video configuration, you must go to the “Video” setup screen, as displayed in Figure 9:
Figure 9: Web GUI “Video” screen of the encoder
Each camera connection (HDMI / Analog) has almost identical settings except for the “Stream” and “Record” resolutions.
SkyHopper PRO V supports broadcast, multicast and unicast video streaming. If you wish to use multiple viewers, a
multicast configuration should be used.
To set up a broadcast or multicast streaming, a proper IP address must be entered in the “Destination IP” field, within the
range of 224.0.0.0 to 239.255.255.255. In this case, the user must also set a proper port in the “Port” field.
To set up a unicast streaming, a valid IP address must be set in the “Destination IP” field - it is recommended to use
standard NAT address. Please pay attention that this should be an IP address of the user’s laptop / PC that is connected
to the “Controller” SkyHopper PRO V unit. In this case, the user will not need to set a proper port in the “Port” field,
because the video streaming will be directed to his laptop / PC. When using a SkyHopper PRO V as a “Remote” unit, the
destination IP and port should be adjusted accordingly.
NOTE –If you use SkyHopper PRO V as an encoder and on the other side you are planning to use SkyHopper
PRO V as a decoder (hardware decoder), the “Destination IP” address MUST be the same on both sides. If you
are planning to use a video player installed on the PC / laptop (software decoder), the “Destination IP” on the
encoder side (“Remote” unit) must be set as an IP address of that specific PC / laptop.

User Manual
19
The user must keep in mind that there are several options to set video streams that depend on which and how many
cameras are connected.
NOTE –When speaking about a video stream, we mean the video we are getting from camera.
In our case, if the recording of the video stream will be defined the same as video stream (HDMI or analog
camera), we’ll be using only one video stream, and one mux. If the recording will have different definitions
from the video streams, it will have a separate mux and that way, the user will be getting two video streams
from one camera, using two muxes (multiplexes).
How many cameras do you
want to connect?
You can get:
1) One HDMI 1080p30 video stream with one analog stream
(see ain the table below)
2) One HDMI 720p60 video stream with one analog stream
(see cin the table below)
3) One HDMI 720p30 video stream with two analog streams
(one stream is for recording) (see ein the table below)
Start
21
Is it analog or
HDMI camera?
You can get up to 2
video streams (one
is for recording),
depends on video
resolution (quality)
Analog
Do you want a
full HD or HD?
HDMI
You can get one
video stream of
1080p30 or two
video streams of
1080p15 (one
stream is for
recording)
You can get one
video stream of
720p60 or two video
streams of 720p30
(one stream is for
recording)
HD
Full HD
Video Stream
HDMI camera
Analog camera
Remarks
a
1 x 1080p30
1 x PAL/NTSC)
Two video streams, while need to set proper
resolution for analog camera.
b
2 x 1080p15
0
HDMI camera streams only, one stream
recorded on SD card.
c
1 x 720p60
1 x (PAL/NTSC)
Two video streams, while need to set proper
resolution for analog camera.
d
2 x 720p30
0
HDMI camera streams only, one stream
recorded on SD card.
e
1 x 720p30
2 x (PAL/NTSC)
Two video streams, while need to set proper
resolution for analog camera. One stream from
analog camera recorded on SD card.
Table 6: Video stream connection options
The user can get up to 2 physical video streams, one from an HDMI camera and one from an Analog camera. In doing so,
there will be involved 2 muxes (that actually combine 2 streams into one). For recording (on SD card), another mux must
be used. So when in the table is seen “2 x” or “1 x”, it refers to the number of video streams that can be used. “2 x” means
that the same stream will be recorded on an SD card as well.
There is an option to set lower resolutions for HDMI / Analog cameras (such as VGA or 480p30 for an HDMI camera and
VGA or CIF for analog camera). In this case, there may be an option to use “2 x” on both cameras. The encoder has 4
muxes, so you cannot obtain more than 4 streams.
The user can set the desired FPS number in “FPS” field.

User Manual
20
The “Audio” trigger enables / disables the audio stream that would be embedded within the video stream. Audio
capabilities are currently disabled, but will be enabled in the near future.
The “Record” trigger enables the recording of a stream over the SD card (if present). The user can select the FPS number
and quality (if it is supported in that resolution combined with the analog stream as described in Table 6).
The “OSD” (On Screen Display) trigger allows for displaying any on-screen message once it is enabled. The user can set a
string or Date/Time stamping. When a GPS antenna is connected to the unit, the date and time will be adjusted
automatically.
There is an option to stream audio only via the encoder, without a video stream. It will only be enabled when both HDMI
and Analog streams will be disabled.
The last one is a “Diagnostics” menu. The user can set the encoder to test mode which sends a color stripe image that
enables the user to test the link and understand if the problem of video streaming is because of the link/configuration or
the camera/cable connection. It should not be triggered when testing it, otherwise the camera video will not be shown.