SkyLink BEETLE WMR-100 User manual

1
SKYLINK BEETLE
User Manual

2
Welcome
Thank you for purchasing Skylink BEETLE for Skylink CDMA Broadband Network!
Before using the Skylink BEETLE, please read this user manual, which outlines the
features and functions of the Skylink BEETLE.
This device operates over the high-speed Skylink networks in the 450MHz band and
Wi-Fi enabling you to connect several devices to the internet and Wi-Fi-enabled devices
anywhere! 

Customerservice 
For customer service, contact at [email protected].
Address : WeTelecom Co., Ltd.
The’O Plus #1604
Sanbon-dong, Gunpo City, Kyunggi-do, KOREA
Phone : [phone]
Limitation of Liability
The information contained in this document is subject to change without notice and
should not be construed as a commitment by Skylink.
Copyright
©2011 WeTelecom Co., Ltd.

3
Contents
1 Before using the Skylink BEETLE .............................................................................................................. 6
Important Notice ................................................................................................................................................ 6
Battery Use and Removal ............................................................................................................................... 6
Safety Hazards ..................................................................................................................................................... 7
The Skylink BEETLE Package .......................................................................................................................... 8
2 Overview : Skylink BEETLE ........................................................................................................................... 9
Introduction .......................................................................................................................................................... 9
Features................................................................................................................................................................... 9
About the Skylink BEETLE Mini Hotspot ............................................................................................... 10
3 Getting Started ............................................................................................................................................... 12
Quick Start Procedure ................................................................................................................................... 12
NetKit Installation for Windows® OS .................................................................................................... 13
NetKit Installation for MAC® OS ............................................................................................................. 13
Minimum System Requirements............................................................................................................... 14
Power Source and Battery Charging ...................................................................................................... 15
LED States ........................................................................................................................................................... 15
How to insert RUIM Card, Battery, and Charge the Battery ........................................................ 16
Powering the Skylink BEETLE On and Off ............................................................................................ 18
Choose between Wi-Fi mode and USB Modem Mode ................................................................. 18
4 Wi-Fi Mode Connection for the First time. ..................................................................................... 19
Browser Interface ............................................................................................................................................. 19
How to Connect to the Skylink BEETLE ................................................................................................. 19
Open the Browser Interface ........................................................................................................................ 21
Home Screen ..................................................................................................................................................... 22
5 Basic Settings in Wi-Fi Mode .................................................................................................................. 24
Setup Wizard ..................................................................................................................................................... 24

4
WWAN Settings ............................................................................................................................................... 24
Temporary Hotspot ........................................................................................................................................ 26
6 Advanced Settings in Wi-Fi Mode ....................................................................................................... 28
Internet Settings .............................................................................................................................................. 28
Wireless Settings .............................................................................................................................................. 29
Firewall ................................................................................................................................................................. 30
Traffic Control ................................................................................................................................................... 32
Utility ..................................................................................................................................................................... 34
Administration................................................................................................................................................... 36
Status .................................................................................................................................................................... 37
7 USB Modem Mode Connection for the First Time ..................................................................... 39
NetKit Installation and Uninstall (Windows® XP) ............................................................................ 39
NetKit Installation and Uninstall (Windows® Vista (or 7)) ........................................................... 43
8 Descriptions of the NetKit GUI in USB Modem Mode ............................................................. 47
Launch the NetKit ........................................................................................................................................... 47
Interface overview ........................................................................................................................................... 47
9 Internet Services in USB Modem Mode ............................................................................................ 48
Accessing the Internet .................................................................................................................................. 48
History Information ........................................................................................................................................ 48
10 SMS Service in USB Modem Mode ................................................................................................... 49
Creating and sending a Message ............................................................................................................ 49
Inbox ..................................................................................................................................................................... 49
Outbox.................................................................................................................................................................. 50
11 PhoneBook in USB Modem Mode ..................................................................................................... 51
Creating a Contact .......................................................................................................................................... 51
Editing a Contact ............................................................................................................................................. 51
Deleting a Contact .......................................................................................................................................... 51

5
Searching a Contact ....................................................................................................................................... 51
Sending a message ........................................................................................................................................ 52
12 Settings and Information in USB Modem Mode ....................................................................... 53
Version Information ........................................................................................................................................ 53
Unlocking the PIN ........................................................................................................................................... 53
Selecting a PPP mode ................................................................................................................................... 53
Enable / Disable PIN ...................................................................................................................................... 54
Change PIN Code ............................................................................................................................................ 54
Selecting Always On Top mode ............................................................................................................... 54
Selecting a Pref Mode ................................................................................................................................... 55
Selecting a language ..................................................................................................................................... 55
13 How to Mac OS in USB Modem Mode ........................................................................................... 56
14 Trouble Shooting ........................................................................................................................................ 57
Reset and Factory Reset ............................................................................................................................... 57
15 Product Specification ................................................................................................................................ 59
Technical Specification .................................................................................................................................. 59

6
1 Before using the Skylink BEETLE
Important Notice
1. When connecting the device to Notebook only with USB Data Cable may cause
more consumption of Notebook’s battery.
2. Using the device for a long time may cause over heating problem, please be
careful. Always try to turn off the power if not in use.
3. Do not forcefully open, fix, or assemble the device; please visit assigned service
center for repair.
4. Be careful not to damage RUIM Card. Inside of RUIM Card, data are stored to
initiate the device and if it is damaged the device may not work.
5. When the device is connected to PC/Notebook do not logout by irregular
method, there might be some abnormal packet data in PC/Notebook. Logout by
normal procedure.
6. Protect the Skylink BEETLE from liquids, dust and excessive heat.
7. Store the Skylink BEETLE in a safe place, when not in use.
8. Turn the power off and remove the battery from device when not in use if
possible.
9. Due to the transmission and reception properties of wireless communications,
data can occasionally be lost or delayed. This can be due to the variation in radio
signal strength that results from changes in the characteristics of the radio
transmission path. Although data loss is rare, the environment where you operate
the Skylink BEETLE may adversely affect communications.
Skylink or its partners will not be held responsible for damages of any kind
resulting from the delays or errors in data transmitted or received with the
Skylink BEETLE device, or failure of the Skylink BEETLE device to transmit or
receive such data.
Battery Use and Removal
1. Never expose batteries to temperatures below -10°C (14°F) or above 45°C
(113°F). For example, never leave the device in a car.
2. Always use Skylink BEETLE’s original battery and charger.

7
3. Do not disassemble/open, crush, or make hole/holes.
4. Do not expose to water or other liquids, expose to fire, explosion, or other
hazardous items.
5. Do not short circuit a battery.
6. Do not contact metallic or conductive object to the battery terminals.
7. Use only genuine battery from Skylink when replacing. Using unreliable battery
may cause a risk of fire, explosion, leakage, or other hazard.
8. When charging the battery, keep it near room temperature.
Safety Hazards
Please do not operate the Skylink BEETLE device in any environment that may be
susceptible to radio interference resulting in danger specifically;
Areas where prohibited by the law
Follow any special rules and regulations and obey all signs and notices.
Always turn off the host device and remove the modem from the USB port
when instructed to do so, or when you suspect that it may cause
interference or danger.
Where explosive atmospheres may be present
Do not operate the Skylink BEETLE in any area where a potentially explosive
atmosphere may exist. Sparks in such areas could cause an explosion or fire
resulting in bodily injury or even death. Be aware and comply with all signs
and instructions.
Users are advised not to operate the Skylink BEETLE while at a refueling
point or service station. Users are reminded to observe restrictions on the
use of radio equipment in fuel depots (fuel storage and distribution areas),
chemical plants or where blasting operations are in progress.
Area with a potentially explosive atmosphere are often but not always clearly
marked. Potential locations can include gas stations, below deck on boats,
chemical transfer or storage facilities, vehicles using liquefied petroleum gas
(such as propane or butane), areas where the air contains chemicals or
particles, such as grain, dust or metal powders, and any other area where
you would normally be advised to turn off your vehicle engine.
Near Medical and life support equipment
Do not operate the Skylink BEETLE in any area where medical equipment,
life support equipment, or near any equipment that may be susceptible to

8
any form of radio interference. In such areas, the host communications
device must be turned off. The Skylink BEETLE may transmit signals that
could interfere with this equipment.
On an aircraft, either on the ground or airborne
Many airline regulations state that you must suspend wireless operations
before boarding an airplane. Please ensure that the host device is turned
off and the Skylink BEETLE is removed from the USB port prior to boarding
aircraft in order to comply with these regulations. The Skylink BEETLE can
transmit signals that could interfere with various onboard systems and
controls.
While operating a vehicle
The driver or operator of any vehicle should not operate a wireless data
device while in control of a vehicle. Doing so will detract from the driver or
operator’s control and operation of that vehicle. In some countries,
operating such communications device while in control of a vehicle is an
offense.
The Skylink BEETLE Package
The Skylink BEETLE package includes:
- Skylink BEETLE Mini Hotspot
- Lithium Ion Battery
- AC Travel Adaptor (T/A)
- MicroUSB Data Cable
- User Manual CD

9
2 Overview : Skylink BEETLE
Introduction
Skylink BEETLE is a mini mobile Hotspot, enabling you with high-speed data access
through CDMA wireless broadband data network and Wi-Fi connectivity anywhere.
Skylink BEETLE offers you more freedom than ever before. The device is a truly wireless
that can work without any cables and less hassle with Software.
Features
Possible to connect the Internet by 1x EV-DO Rev. A, High speed
Wireless Broadband Data Network.
Choose between Two operating mode :
Wireless data networking with Wi-Fi or USB Cable
-Single user: One can use it with USB data cable as Modem mode or
without data cable as Wi-Fi mode.
-Multiple users: Use as Wi-Fi mode.
-The Skylink BEETLE package includes a battery to work on both Wi-Fi
mode and USB Modem mode.
-When using as USB Modem mode, the driver and “NetKit” program will
automatically installed into PC/Notebook.
Using as Wi-Fi Mode
-Multiple users can access the Internet and exchange e-mails at the same
time.
-Possible to connect to Wi-Fi devices: Such as Notebooks, Desktops,
Tablet PC, Smartphone, PDA (Personal Digital Assistants), and consumer
devices that supports Wi-Fi.
-Since the device is equipped with latest Wi-Fi Router chipset, it supports
Wi-Fi 802.11 b/g/n technology.

10
Using as USB Modem Mode
-By using NetKit program, it easily connects to the Internet.
-Driver and NetKit program will automatically be installed. Supported OS
are Windows XP, Vista, Windows 7 and Mac OS (check the version)
VPN Capability
SMS supported
About the Skylink BEETLE Mini Hotspot
1. Power Button and Status Indicators
-Indicates power, battery and CDMA communication activities.
-Please refer to the Power Button LED status page. (See page 14 for
Power Button LED description)
2. Wi-Fi Router Status Indicator
-Indicates Wi-Fi Router status. (See page 14 for Wi-Fi Router Status
Indicator LED description)
3. External Antenna Connector
-Enable you to use external antenna for better signal reception. (External
antenna is not included in the package.)
1
2
3 4

11
4. MicroUSB Connector
-Connects to desktops/notebooks with a Type A USB port.
5. Factory Reset button
-Resets the device to initial factory settings.
6. RUIM Card Slot
-RUIM card is inserted here.
7. Battery Compartment
-Battery is inserted here.
5
6
7

12
3 Getting Started
Hope this will help you to guide and to get started with the Skylink BEETLE in this
chapter. There are two modes in the Skylink BEETLE Mini Wi-Fi Router, one is Wi-Fi and
the other is USB Modem.
Quick Start Procedure
Before you begin with Skylink BEETLE, please follow few steps:
1. Check to make sure your computer meets the minimum system requirements.
(See page 14 for Minimum System Requirements.)
2. Slide to open the battery cover at the bottom of the device.
3. Insert RUIM card that provided by service provider to RUIM slot.
4. Insert a charged battery.
5. Connect the AC Travel Adaptor to the device and charge it for 3 hours before
using the device.
6. Choose between either Wi-Fi Mode or USB Modem mode.
-When multiple users are using, choose Wi-Fi mode.
-When single user is using, choose USB Modem mode or Wi-Fi Mode
7. Using as Wi-Fi mode for the first time,
①Press the Power button on Skylink BEETLE, shortly. The Power button LED
and Wi-Fi LED will flash.
②Use Wi-Fi manager on your computer to locate the Skylink BEETLE Wi-Fi
network.
③Find “WMR-100AP_XXXXXX” network in the list of available wireless
networks and click “Connect”.
④From your computer’s Web browser, enter http://192.168.0.254 into the
address window and press the Enter or Return key.
⑤Enter the id & password “admin”, “admin” when requested.
⑥Using for the first time, Setup Wizard will launch on the screen. It will
guide you through setting up security of your device.

13
⑦Follow the instructions on the screen.
⑧After you click “Done”, your device will start.
For more details and information on Wi-Fi mode connection, please refer
sections from “4. Wi-Fi Mode Connection for the first time” to “6.
Advanced Setting in Wi-Fi Mode”.
8. Using as USB Modem Mode for the first time,
①Plug USB data cable into Skylink BEETLE and USB port on your computer.
The device will be power on automatically. The Power button LED will
light on but the Wi-Fi status LED will not lit.
②Launch NetKit software for either Windows OS or Mac OS as follows.
NetKit Installation for Windows® OS
i. If USB DRIVER is not present, Modem package Installer will
run automatically.
Tip
If Modem package Installer doesn’t work automatically, Execute RunPack.exe
manually.
ii. Select the desire language and press “OK”. Welcoming
message for using NetKit Program window will be shown.
iii. Press “Install” button. The program starts automatically.
iv. Press “Finish” button once it is done with program
installation.
v. It will now start to install the USB driver. Please check
whether the driver has been installed properly by checking
<Device Manager>.
NetKit Installation for MAC® OS
i. Plug the Skylink BEETLE in USB port on MAC.

14
ii. Open SkyLink CD, start mintechUSBCDC and install MAC
Drivers. Restart MAC.
iii. Execute any connection manager for Skylink BEETLE Mobile
Products.
iv. Enter the User ID, Password and Number in Network
Preference, and connect Internet.
For more details and information for USB Modem mode connection, please
review section from “7. USB Modem Mode Connection for the First Time”
to “13.How to Mac OS in USB Modem Mode”.
Minimum System Requirements
1. PC Hardware
- Recommend to use PC/Notebook at speed of 300 MHz or higher.
- Wireless LAN is essential. Recommending 802.11 b/g/n 2.4GHz.
- Minimum 233 MHz speed required
* Intel Pentium/Celeron products, AMD K6/Athlon/Duron products or compatible
processors
- Recommend to use 128MB RAM or higher
- At least 100 MB of free hard disk space is required.
- Motherboard or PCI card that supports USB.
- Video adaptor with Super VGA (800 x 600) or higher resolution and Monitor
- CD-ROM or DVD Optical Drive
- Keyboard and Mouse
2. Operating System
- Windows® XP Home or Professional ( with Service Pack 2 )
- Windows® 2000 (with Service Pack 4 for optimal performances)
- Windows® Vista 32bits/64bits
- Windows® 7 32bits/64bits
- Mac OS 10.4 or higher

15
< Recommended parameters >
Windows Update : Keep your computer up to date
Power Source and Battery Charging
There are three power sources that Skylink BEETLE may use.
-Battery
-AC Travel Adaptor
-USB Data Cable
User must press Power button to turn on the device even though the Battery and AC
Travel Adaptor are connected. If USB cable is connected between the device and
PC/notebook, the device will be turned on automatically without pressing the Power
button.
When Power button is not pressed, then battery will be charged only through either USB
Cable or AC Travel Adaptor.
LED States
Wi-Fi Router Status LED
LED Status Status information
LED not lit No Power (Wi-Fi mode off)
LED Green Solid Wi-Fi Powered
LED Green Blink Wi-Fi transmitting and receiving data;
Blinking rate proportional to data speed

16
Power Button LED
LED Status Status information
LED not lit No Power
LED RED Solid Power ON
LED RED Blink Low Battery warning
LED Green Solid Service Available
LED Green Blink Service Not Available
LED Blue Solid Connected to EVDO
LED Blue Blink Connected to 1x
LED Orange Solid Charging
LED Orange Blink Fully Charged
How to insert RUIM Card, Battery, and Charge the Battery
For first time use of Skylink BEETLE Mini Hotspot, we recommend to follow below
sequences.
Note
Before using the Skylink BEETLE Mini Hotspot for the first time, please
insert RUIM card and fully charged battery.
1. Open the battery cover, which located in the bottom of the device

17
2. Insert RUIM Card that provided by the service provider. See the below
picture for more detail.
3. Insert the battery by lining up battery contact point with the gold contact
points.
4. Once the battery is securely settled, put the battery cover back into the
device until it locks firmly.

18
5. Plug the AC travel adaptor into the proper electrical outlet and connect
MicroUSB port of the AC travel adaptor to the MicroUSB port of the
device. Charge the battery for at least three hours.
Powering the Skylink BEETLE On and Off
To power the device on:
Press the Power button until the Power LED lights up solid red.
And solid green LED indicates the device is in service area and ready to connect.
(Press Power button for two to three seconds to power on)
To power the device off:
Press the Power button until the Power LED shuts off.
(Press Power button for two to three seconds to power off)
Choose between Wi-Fi mode and USB Modem Mode
When setup is completed, you can choose one of two modes : Wi-Fi mode or
USB Modem mode.
Note
Pressing Power button, the device will automatically connected to Wi-Fi
mode if MicroUSB Data Cable is not connected.

19
4 Wi-Fi Mode Connection for the First time.
Browser Interface
Skylink BEETLE uses a browser interface to configure the device.
The browser interface lets you:
 View the status aspects of your network.
 Set up wireless security, including MAC, port filtering and Port forwarding.
 Set up a temporary hotspot to allow a maximum of five connections to your
device without having to share your network name and network key.
How to Connect to the Skylink BEETLE
1. Insert RUIM Card and Battery with AC Travel Adaptor
2. Press Power button to connect to Wi-Fi mode .
3. Use your default Wi-Fi manager to locate the Skylink BEETLE wireless network.
Tip
The Steps of connecting to a Wi-Fi network vary depending on your operating
system whether you use the native application or third-party software.
Generally you click an icon (often in the Windows notification area or System
Preferences>Network on a Mac) where you can select “View Available Wireless
Networks.” If you are unfamiliar with wireless networking on your computer,
consult the computer help system.
4. If multiple wireless networks are found, highlight the one that indicated as “WMR-
100AP_XXXXXX” in its name.
5. Click Connect.
6. If this is your first time connecting to the Skylink BEETLE, continue with these steps.