SLIDEWHIZZER SWSL-03 User manual

SLIDEWHIZZER 10FT SLIDE
ASSEMBLY INSTRUCTIONS
page 1 of 20

CUSTOMER SERVICE INFORMATION
Thank you for purchasing:
SLIDEWHIZZER 10FT SLIDE
MODEL# SWSL-03
latports® strives for 100% satisfaction guarantee, as customer satisfaction is of utmost importance
to us. Before assembly, we suggest you to review all the components of the product you have purchased
and contact us within 30 days of purchase for replacement parts. We will replace all missing or damaged
parts at no extra charge.
To submit a request for a replacement part, please include the following information:
Name:
Mailing address:
roduct name:
roduct model:
art #:
Retailer where purchase was made:
Date of purchase:
Order #:
Quantity:
Please note t at replacement part requests require a p oto for submission.
If you wish to request a replacement part, have other questions or concerns about this product,
or order additional parts, please contact us at:
LAT ORTS
O BOX 501553 San Diego, CA, 92150
page 2 of 20

LIMITED WARRANTY
latports® warrants this product to be free from defects in workmanship and materials under normal
use and conditions for a period of 90 DAYS FROM THE DATE OF ORINGINAL URCHASE.This Limited Warranty
is not transferable and is available only for the original purchaser of the roduct. The Company's obligation
under this warranty is limited to replacing or repairing the roduct, at the discretion of the Company.
All warranty coverage extends only to the original retail purchaser from the date of purchase, latports®
obligation under this warranty is limited to replacing or repairing, at latports® option.
All products for which a warranty claim is made must be received by latports® and accompanied by
sufficient proof of purchase (photocopy of the original store receipt, indicating the date of purchase).
All freight and handling fees are the responsibility of the customer to pay, both to and from latports®.
All warranty claims must be preauthorized by latports®. reauthorization can be obtained by
contacting latports®.
This warranty does not cover ordinary wear and tear, weathering, failure to follow directions,
improper installation, improper maintenance, or acts of nature (such as damage caused by wind, lightning,
snow, water or ice). Weather damage, damage caused by unauthorized repair work or damage caused by
improper use of the products are not covered by the product warranty. No other warranty beyond that
specifically set forth above is authorized by latports®
latports®IS NOT RES ONSIBLE OR LIABLE FOR INDIRECT, S ECIAL OR CONSEQUENTIAL DAMAGE RISING OUT
OF OR IN CONNECTION WITH THE USE OR ERFORMANCE OF THE RODUCT OR OTHER DAMAGE WITH RES ECT
TO ANY ECONOMIC LOSS, LOSS OF RO ERTY, LOSS OF REVENUE OR ROFITS, LOSS OF ENJOYMENT OR USE,
COST OF REMOVAL, INSTALLATION OR OTHER CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES.
ACCORDINGLY, THE ABOVE LIMITATION MAY NOT A LY TO YOU.THE WARRANTY EXTENDED HEREUNDER IS
IN LIEU OF ALL OTHER WARRANTIES AND latports®, S ECIFICALLY DISCLAIMS ANY IM LIED WARRANTY OF
MERCHANTABILIY OR FITNESS FOR A ARTICULAR UR OSE IS LIMITED IN ITS SCO E AND DURATION TO
THE TERMS SET FORTH HEREIN.
WHILE EVERY ATTEM T IS MADE TO ENSURE THE HIGHEST DEGREE OF ROTECTION IN ALL EQUI MENT,
WE CANNOT GUARANTEE FREEDOM OF INJURY. THE USER ASSUMES ALL RISK OF INJURY DUE TO USE.
ALL MERCHANDISE IS SOLD ON THIS CONDITION, WHICH NO RE RESENTATIVE OF latports®CAN WAIVE OR
CHANGE.
page 3 of 20

WARNINGS
WARNING:
While every attempt is made to ensure the highest degree of protection in all equipment, freedom from injury
cannot be guaranteed. The user assumes all risks of injury due to use. It is on this condition that all
merchandise is sold, which cannot be changed or waived by any representatives of the company.
CHOKING HAZARD
- Small arts
NOT
for children under 3 years of age.
WARNING - PLEASE READ
ADULT ASSEMBLY REQUIRED
page 4 of 20

WARNINGS
Please read t e information in t is manual in its entirety.
Noncompliance to the instructions may increase the risk of serious injury and/or death:
This unit must be assembled and disassembled by ADULTS ONLY.
DO NOT install this equipment over concrete, asphalt, or any other hard or rough surface. A fall onto a hard
surface can result in serious injury. The SLIDEWHIZZER 10FT SLIDE should always be installed over an
appropriate, stable surface (rubber mat, grass, etc). It is recommended that whenever possible the
ground anchors are used and firmly inserted into the ground.
lace this equipment on stable, level surface AT LEAST 7 feet away from any structure, obstruction,
or possible hazard(s) such as walls, pools, power lines, overhangs, other playground equipment, driveways,
hard surfaces and/or roads.
DO NOT attach items to the SLIDEWHIZZER 10FT SLIDE not specifically designed for this purpose by
the manufacturer, (i.e. cables, jump ropes, chains, clotheslines, or leashes) to avoid the risk of strangulation
or other physical injuries.
DO NOT use this product in a way that is other than its intended use.
DO NOT leave children unattended; Children must be supervised at all times when this equipment is in use.
DO NOT allow more than one child on the SLIDEWHIZZER 10FT SLIDE at a time.
DO instruct children to ensure that the chute at the bottom is clear of any obstructions before sliding.
DO NOT place objects on or under the slide.
DO NOT allow people and pets to stand, sit on/near/under the SLIDEWHIZZER 10FT SLIDE.
DO NOT allow children to stand on the slide chute or top. DO NOT allow children to attempt to walk up the
slide or hang from the steel tubing. Children should ALWAYS be securely seated, in the forward-facing
position when sliding.
DO NOT allow children to lay down, slide from a standing position, or slide down the chute backwards.
ALWAYS wear the appropriate footwear [i.e. closed toe] and clothing when using the SLIDEWHIZZER
10FT SLIDE.
DO NOT allow children to wear loose fitting clothing, clothing with straps/loops, backpacks or accessories
with straps or loops, or sharp edges which may present a hazard or become snagged or caught on the
SLIDEWHIZZER 10FT SLIDE during use Serious injury and/or accidental strangulation may occur.
page 5 of 20

Long pants are recommended for sliding to prevent friction of skin against the chute.
DO NOT allow children to wear glasses or helmets when using the SLIDEWHIZZER 10FT SLIDE.
Examine and replace any worn, loose, defective, rusted or missing parts and/or bolts before use.
It is imperative that all parts are inspected to ensure that they are attached and are in good condition.
If any loose, cracked, missing, or otherwise damaged components are found, refrain from use. If product is
removed for winter storage, reinstall all plastic parts before use.
DO NOT exceed the maximum weight limit of 110lbs (50kgs).
This unit has a maximum fall height of 61"
Suitable for use by most children from 3 to 10 years of age.
This SLIDEWHIZZER 10FT SLIDE is NOT for adults or adolescents.
lease read and refer to other warnings in the SLIDEWHIZZER 10FT SLIDE instructions before use.
ASSEMBLY WARNINGS
When you are ready to start, make sure that you have the correct tools at hand, and adequate space for
assembly. lease refer to the table for part descriptions and numbers. The assembly nstruction uses these
descriptions and numbers as reference. Make sure you have all parts listed.
IMPORTANT: USE GLOVES TO PROTECT AGAINST PINCH POINTS
Enclosed are the current specifications and product features available DURING ASSEMBLY. At time of printing,
however, changes may be made in equipment, availability, specifications and features without notice.
page 6 of 20

EXPLOSIVE DRAWING
page 7 of 20

Ref Qty
Description Illustration
A M6 60mm bolt 2
B M6 50mm bolt 4
C M6 35mm bolt 19
D M6 20mm bolt 2
E M6 15mm bolt 6
F M6 washer 21
G M6 spring washer 29
H M6 domenut 21
I M6 square domenut 8
J Ladder step 4
K 1
Top SLIDEWHIZZER chute
(with Rounded-edge)
COMPONENTS LIST
page 8 of 20

Ref Qty
COMPONENTS LIST
Description Illustraion
L Middle wavy slide chute 1
M Bottom wavy slide chute 1
M1 lastic spacer 2
N Tie bar 1
O Cross tie bar 1
Ladder stabilizer bar 1
Q L/R support bar 2
R Main handrail tube 2
S Top handrail tube 2
T Support-frame of top slide chute 1
page 9 of 20

Ref Qty
COMPONENTS LIST
Description Illustraion
U Support bar for Top slide chute 1
V L/R support bar for bottom slide chute 2
W Support bar for bottom slide chute 1
X Spanner 1
Y Ground anchor 2
Y1 Hex Head Self-Tapping Screw(5/16" x 6") 2
Z lastic end-cap 6
Tools required :
1. Combination wrench 10
2. hilips head screwdriver
Use the Components List to ensure all parts are present.
Do not attempt to assemble the slide if parts are missing
page 10 of 20

E=M6x15mm x 6pcs A=M6x60mm x 2pcs, I=square domenut x 2pcs
D=M6x20mm x 2pcs C=M6x35mm x 6pcs, I=square domenut x 6pcs
B=M6x50mm x 4pcs C=M6x35mm x 13pcs
SLIDEWHIZZER 10ft slide screw & domenut placement
page 11 of 20

lease note that slide assembly will be considerably easier with two adults.While one adult is connecting
and fastening the relevant pieces, the other can assist by supporting the slide chute and holding the
Step 1
C (M6x35) 1 x
F (M6) 1 x
G (M6) 1 x
H (M6) 1 x
￭ Attach the Support bar for bottom slide chute (W) to Cross tie bar (O) with bolt Cx1 + washer Fx1 +
spring washer Gx1 + domenut Hx1.
Step 2
E (M6x15) 2 x
￭ Turn the Bottom slide chute (M) backside up and connect the Support bar for bottom slide chute (W)
onto the Bottom slide chute (M) with bolt Ex1.
connecting pieces in position.
SLIDEWHIZZER 10FT SLIDE ASSEMBLY INSTRUCTION
O
W
O
W
C
F
GH
M
O
W
M
W
E
35MM
6MM
15MM
6MM
page 12 of 20

Step 3
E (M6x15) 2 x
F (M6) 2 x
G (M6) 2 x
H (M6) 2 x
￭ Connect the Middle slide chute (L) and Bottom wavy slide chute (M) by embedding tongue-and-groove
joint firmly, ensure the connection meet closely and without any gaps between the chutes.
￭ Leave the lower screw hole of Middle and Bottom slide chute unassembled.
Step 4
ensure the connection meet closely and without any gaps between the chutes.
￭ Thread the upper screw hole of Middle and Bottom slide chute with bolt Ex1 + washer Fx1 +
spring washer Gx1 + domenut Hx1.
￭ Connect the Top slide chute (K) and Middle slide chute (L) by embedding tongue-and-groove joint firmly,
Upper screw ole
Lower screw ole
L
M
E
F
G
H
Upper screw ole
figure 1
L
15M
6M
* Tools recommendation for
figure 1:
Using t e long nose pilers to fix
t e nut for t e small area.
KLM
L
K
L
M
page 13 of 20

Step 5
B (M6x50) 4 x
F (M6) 4 x
G (M6) 4 x
H (M6) 4 x
Z 2 x
￭ Insert the lastic end-cap (Z) into the Support-frame of top slide chute (T).
￭ lace the lastic spacer (M1) between Top slide chute (K) and Top handrail (S).
Attach the Support-frame of top slide chute (T) to Top handrail tube (S) and fasten (T), (K), (S) and (M1)
4pcs together with bolt Bx1 + washer Fx1 + spring washer Gx1 + domenut Hx1.
Step 6
C (M6x35) 6 x
G (M6) 6 x
I (M6) 6 x
Z 2 x
￭ Embed the 1st, 2nd and 4th Ladder step (J) to Main handrail (R) with bolt Cx1 + spring washer Gx1 +
square domenut Ix1 as figure 1 and leave the 3rd ladder step unassembled.
￭ Insert the lastic end-cap (Z) into the end of short steel tube close to the 4th ladder step.
K
T
M
S
Z
Z
L
B
F
B
F
G
H
S
L
K
T
50MM
6MM
35MM
6MM
* Tools recommendation for figure
1: Using
t e long nose pilers to fix t e nut for
t e small area.
figure 1
J
R
G
C
I
figure 1
R
Z
Z
R
page 14 of 20

Step 7
C (M6x35) 6 x
F (M6) 6 x
G (M6) 6 x
H (M6) 6 x
￭ Attach the Main handrail (R) with ladders (J) into the top handrail (S) with bolt Cx1 + washer Fx1 +
spring washer Gx1 + domenut Hx1.
Step 8
D (M6x20) 2 x
E (M6x15) 2 x
F (M6) 2 x
G (M6) 2 x
H (M6) 2 x
and bottom slide chute (M).
domenut Hx1.
￭ lace straight side of the support bar (V) outward to the bottom hole of the middle slide chute (L)
￭ Secure the top of (V) to the bottom hole of (L) & (M) with bolt Dx1 + washer Fx1 + spring washer Gx1 +
￭ Secure the bottom of (V) to the cross tie bar (O) with bolt Ex1.
K
R
S
C
F
G
H
C
C
F
F
Z
G
H
G
H
S
R
K
L
M
KLM
O
V
V
* W ile one adult is connecting t e
support bar wit slide c ute, t e
ot er adult can assist by olding
t e slide c ute.
20M
6M
35MM
6MM
* Tools recommendation for
figure 1:
Using t e long nose pilers to fix
t e nut for t e small area.
figure 1
page 15 of 20

Step 9
C (M6x35) 3 x
F (M6) 3 x
G (M6) 3 x
H (M6) 3 x
Step 10
C (M6x35) 1 x
F (M6) 1 x
G (M6) 1 x
H (M6) 1 x
￭ Slide the Cross tie bar (O) into the Tie bar (N) as figure 1 and place the Support bar for
middle slide chute (U) into rounded-pedestal on the back side of middle slide chute (L) as figure 2.
￭ Thread (O), (N) and (U) with bolt Cx1 + washer Fx1 + spring washer Gx1 + domenut Hx1 as figure 3.
￭ Secure the Tie bar (N) to Ladder stablilizer bar ( ) with bolt Cx1 + washer Fx1 + spring washer Gx1 +
domenut Hx1.
￭ Attach the Ladder stabilizer bar ( ) to pre-assembled Main handrail (R) with bolt Cx1 + washer Fx1 +
spring washer Gx1 + domenut Hx1.
N
U
O
figure 1
C
F
H
G
O
N
U
figure 3
O
N
U
P
RR
J
N
L
* W ile one adult is
connecting ladder
stabilizer wit ladder, t e
ot er adult can assist by
olding t e slide c ute.
35MM
6MM
35MM
6MM
P
N
C
F
H
G
R
C
F
H
G
U
L
rounded-
pedestal
figure 2
page 16 of 20

Step 11
C (M6x35) 2 x
F (M6) 2 x
G (M6) 2 x
H (M6) 2 x
Step 12
A (M6x60) 2 x
G (M6) 2 x
I (M6) 2 x
Z 2 x
￭ Fasten the Support bar (Q) and Main handrail tube (R) to the 3rd step (J) with bolt Ax1 +
spring washer Gx1 + square domenut Ix1.
￭
Insert the lastic end-cap (Z) into the end of Support bar (Q).
￭ Connect the Support bar (Q) into the Ladder stablilizer bar ( ) with bolt Cx1 + washer Fx1 +
spring washer Gx1 + domenut Hx1)
P
Q
Q
P
Q
Q
3rd step
R
R
60MM
6MM
35MM
6MM
P
Q
C
F
H
G
P
Q
J
R
G
A
I
Z
Z
Q
R
page 17 of 20

Step 13
Y
2 x
Y1
2 x
￭ Secure both sides of ladder stablilizer bar ( ) to the ground with ground anchors (Y) and
self-tapping screws(Y1).
￭ When selecting a place to install the equipment, please consider the space requirement
(at least 7 feet all around the slide). lease avoid positioning the equipment from protruding elements,
walls, trees, etc.
￭ Once the equipment has been assembled, please make sure that it is placed on level ground and that
it is completely stable. DO NOT place the equipment on carpet.
￭ Do not install the equipment in wet areas which may cause the equipment to rust.
page 18 of 20

HOW TO TRUN YOUR 10FT SLIDE INTO A WATER SLIDE IN 3 STEPS:
1. Obtain: 3/4 inch vinyl tubing (vinyl tubing not included). 2 hose clamps are included in your package.
2. Insert one end of tubing into water slide connector underneath top chute piece (component K).
Secure with a hose clamp.
3. Insert the other end of the tubing into water spigot. Secure with a hose clamp.
page 19 of 20

CARE & MAINTENANCE
To clean the slide, simply wipe with a damp cloth.
Regularly check to see if slide chute, steel tubes, steps, ground anchors and other parts are tightened and
completely secure.
Replace worn and damaged parts when if found and if necessary, refrain from use until replacement parts
can be obtained.
If the paint is chipped, we recommend you lightly rub the damaged area and cover using a non-toxic
enamel paint.
IM ORTANT: While no regular maintenance is required, you must inspect the slide before each use and
replace any worn, defective, or missing parts. The following conditions could represent potential hazards:
missing, improperly positioned, or insecurely attached ground anchors or slide chute, missing, improperly
secured or damaged ladder steps, a bent or broken frame, and/ or bent or buckled Stabilizer or Tie Bars.
Stop using slide immediately and guard against unauthorized use until slide is properly repaired.
FREQUENTLY ASKED QUESTIONS
Question: “How should I clean my slide?”
Answer: You should clean the slide with a solution of warm water and non- corrosive/abrasive soap.
Dampen rag with this solution and wipe completely dry before using
Question: “Is there any maintenance I need to do for my slide?”
Answer: You should always double check to make sure all your bolts are tight and secure, and that the
ground anchors are present and securely in place before use.
Question: “Something was missing from the packaging,” “I need to purchase a replacement part”or
“I discovered a damaged piece. What should I do?”
Answer: Contact latports®. You must have proof of purchase and/or order confirmation
available to be considered for warranty replacement. You must report missing pieces
within 30 Days from date of purchase.
Question: “A step seems loose, what should I do?”
Answer: Make sure the bolts under the plastic steps are secure.
page 20 of 20