SMART GT07 User manual

GPS
GPS
GPS
GPS Vehicle
Vehicle
Vehicle
Vehicle tracker
tracker
tracker
tracker
(
(
(
( Anti-theft
Anti-theft
Anti-theft
Anti-theft Tracking
Tracking
Tracking
Tracking &
&
&
& Positioning
Positioning
Positioning
Positioning )
)
)
)
GT07
GT07
GT07
GT07 USER
USER
USER
USER MANUAL
MANUAL
MANUAL
MANUAL
(Version 2.1)
Please read this manual carefully before attempting installation and online activation.
Pictures are for indication and illustration purposes only.

1.
1.
1.
1. Accessories:
Accessories:
Accessories:
Accessories:
2.
2.
2.
2. Features:
Features:
Features:
Features:
�Wide voltage input range: 9-36vDC
�GPS position upload via GPRS as preset interval
�Check location via SMS
�Built-in vibration sensor, intelligent theft-proof
�ACC ignition detection
�Tele-cutoff (petrol/ electricity) function
3.
3.
3.
3. Interface
Interface
Interface
Interface introduction
introduction
introduction
introduction

3.1 Red LED(power/working status)
LED Status Meaning
Continuously in dark state power off
Slow flashing Working normally
3.2 Green LED(GSM status indicator)
LED Status Meaning
flashing Receive GSM signal normally
Slow flashing Start GPRS
Continuously in dark state No GSM signal
3.3Blue LED(GPS status indicator)
LED Status Meaning
Quick flashing Searching GPS signal, not located
Slow flashing GPS located
Continuously in dark state GPS is in sleep mode or not working
3.4 Ignition detection indication
Three (blue/red/green) LEDs are in cycling flashing
4.
4.
4.
4. Method
Method
Method
Method of
of
of
of installation
installation
installation
installation
4.1 Installing SIM card
�Open the SIM card silicon seal
�insert the SIM card to the slot (do not insert the SIM card backwards) and lock it

Note:
�Power off before installing or removing the SIM card.
�The SIM card used should be available for GPRS
4.2 Note of installation
�Covertly installation, be aware of water drops
�Stay away from interference of electromagnetic signals
�Fixed firmly into position
�Make sure the device face towards sky, with no metal object above it to interfere
with GPS signal
�The standard voltage is 9V-36VDC. Please use the power line which provided by
the manufacturer. There is a power converter box in the power wire.
�Device wiring diagram
�The device will power on automatically when connected to power. The power
status LED will light up.

5.
5.
5.
5. Cautions
Cautions
Cautions
Cautions of
of
of
of device
device
device
device wiring
wiring
wiring
wiring
5.1 Power:
The standard voltage is 9V-36VDC. Please use the power line which provided by the
manufacturer. The red line is the positive. The black line is the negative.
5.2 ACC/Tele-cutoff (petrol/electricity) control line
5.2.1 ACC lin e (white) is c onnected to the ACC switch of the vehicle. Please make
sure to connect the ACC line. The tracker will decide whether to enter ignition
detection according to ACC status. If do not connect to ACC line, the device will
enter ignition detection status. If the vehicle vibrates when moving, it will activate the
vibration alarm. If there is no need for the theft proof function, connect the ACC line
to the positive in parallel and keep high level.
5.2.2 Tele-cutoff (petrol/ electricity) control line (yellow) is connected to pin 86 of the
Tele-cutoff (petrol/ electricity) relay (equal to the yellow line of the relay socket).
5.3 Notes of the relay installation:
GT07 is designed and matched by 12V relay. It is suitable to be installed in vehicle
with 12V battery. If it is a vehicle with 24V battery, it should be matched by 24V
relay.
6.
6.
6.
6. Parameter
Parameter
Parameter
Parameter setting
setting
setting
setting
The SMS command format is no case sensitive and it is divided by comma. There is a
reply SMS after sending the command. If set successfully, there will be a SMS reply
with “ OK ” ; or else please set again.
The device will reply the corresponding information after sending the SMS command.
The device receives SMS command from any number as default.
6.1 Set SOS number
SMS command to the device to set the SOS number.
SOS,A,No.1,No.2,No.3#
SOS,A,No.1,No.2,No.3#
SOS,A,No.1,No.2,No.3#
SOS,A,No.1,No.2,No.3#
“
A
”
means to add new numbers, for example:
SOS,A, 13510905991,13510905992,13527852360#
If there is only one SOS number, you can appoint a specific number as SOS number.
And the null means no adding.
For example:
SOS,A,13510905991# means to set the first number as SOS number

SOS,A,,13510905992# means to set the second number as SOS number
SOS,A,,,13510905993# means to set the third number as SOS number
If set successfully, there will be a SMS reply with “ OK ” .
6.2 Delete SOS specific number
Before deleting specific number, please check its corresponding code.
SMS command to the device to delete the number.
SOS,D,serial
SOS,D,serial
SOS,D,serial
SOS,D,serial NO.1,serial
NO.1,serial
NO.1,serial
NO.1,serial NO.2,serial
NO.2,serial
NO.2,serial
NO.2,serial NO.3#
NO.3#
NO.3#
NO.3#
“
D
”
means to delete the number, for example:
SOS,D,1# means to delete the first number
SOS,D,3# means to delete the third number
If you want to delete more than one numbers, you can send this command:
SOS,D,1,3# means to delete the first and third numbers.
If you forget serial number of the mobile number you want delete, you can
send this command:
SOS,D,mobile
SOS,D,mobile
SOS,D,mobile
SOS,D,mobile number#
number#
number#
number# means to delete the mobile number directly.
For example:
SOS,D,13527852360# means to delete the 13527852360 directly.
If deleting the SOS number successfully, there will be a SMS reply with “ OK ” .
6.3 Check parameter settings
The SMS command send to the device to check the device settings.
Command format: PARAM#
PARAM#
PARAM#
PARAM#
e.g.: PARAM#
Reply information:
IMEI:
IMEI:
IMEI:
IMEI: 353419037523839
353419037523839
353419037523839
353419037523839 ---- IMEI number of the device
Timezone:E,8,0;
Timezone:E,8,0;
Timezone:E,8,0;
Timezone:E,8,0; -----set time zone; default as E8
SOS
SOS
SOS
SOS Number:
Number:
Number:
Number: 13510905991,13510905992,13527852360;
13510905991,13510905992,13527852360;
13510905991,13510905992,13527852360;
13510905991,13510905992,13527852360; ------SOS numbers,
maximum three SOS numbers used for alarm
SENSOR:10;
SENSOR:10;
SENSOR:10;
SENSOR:10; 180;-
180;-
180;-
180;- -----sensor detecting time(default as 10s); vibration alarm
delay(default as 180s, the time ranges from 10-300s)
SENDS:2;
SENDS:2;
SENDS:2;
SENDS:2; -------the delay time when GPS is entering sleep state, default as
2mins(when ACC is off, vibration stop, vehicle does not move, GPS will enter sleep
state for saving power )
SVL:M;-
SVL:M;-
SVL:M;-
SVL:M;- ----vibration sensitivity , default as M (L refers to low, M refers to middle, H
refers to high)
ALARM:10;-
ALARM:10;-
ALARM:10;-
ALARM:10;- ----sensor alarm delay, the time ranges from 1-60mins.
TIMESET:20;
TIMESET:20;
TIMESET:20;
TIMESET:20; ----- With ACC OFF and the alarm is activated, GPS will continuously
uploaded data in 20 m inutes(default as 20mins). The time range is 1 to 999 minutes.
6.4 Setup GPRS time interval

T he default GPRS sending time interval is 20s which means the device will upload
positioning data to the platform server every 20s. Users can modify GPS time interval
by SMS
Command format: “
“
“
“ TIMER,time(seconds)#
TIMER,time(seconds)#
TIMER,time(seconds)#
TIMER,time(seconds)#
The time range is from 10-18000seconds.
e.g.: TIMER,10#
It means GPRS sending time interval is 10 which means the device will upload
positioning data to the platform server every 10 seconds.
6.5 Sensor Alarm time
W hen the vehicle power is off, the ACC cable is in low level. If the vehicle power
keeps off for 10mins, the device will come to the state of sensor alarm preparation
automatically. I n that case, if several times of vibration happened , the device will
trigger vibration alarm mechanism . A fter that, if the vehicle is still of (low-level ACC
cable) in the following 3mins, the device will alarm instantly.
T he sensor alarm preparation time can be modified by SMS.
Command format: “
“
“
“ DEFENSE,
DEFENSE,
DEFENSE,
DEFENSE, time
time
time
time (minutes)#
(minutes)#
(minutes)#
(minutes)# ”
”
”
”
T he time ranges from 1 to 60 minutes.
e.g.: DEFENSE,
DEFENSE,
DEFENSE,
DEFENSE, 15#.
15#.
15#.
15#.
I t means when ACC cable is in low level of 15 minutes, the device will get into the
state of sensor alarm.
6.6 Factory Recovery Settings
W hen the device can ’ t work normally , which is resulted from wrong parameters
settings , the user can send SMS to have the device recovered into default parameters.
SMS command: FACTORY
FACTORY
FACTORY
FACTORY #
#
#
#
W hen the device gets command, it will recover parameters into default value.
6.7 Reboot Device
When there is something wrong with the link of GPRS, e.g., the parameter setting of
the device is correct, but you can ’ t track the car on the platform.
At this moment you can send a command to the device to reboot the device.
SMS command: RESET#
RESET#
RESET#
RESET#
W hen device gets command, it will reboot after 1min.
6.8 Vibration Sensitivity Setup (Please be careful to use this function.)
User can send SMS to device:
SVL,
SVL,
SVL,
SVL, L#
L#
L#
L# ------setting vibration sensitivity as low

SVL,
SVL,
SVL,
SVL, M#
M#
M#
M# -------setting vibration sensitivity as medium
SVL,
SVL,
SVL,
SVL, H#
H#
H#
H# -------setting vibration sensitivity as high
Note: users should be careful to alter parameters of vibration sensitivity, in case of
making wrong vibration alarm. I t is recommended that this parameters to be set up by
installation dealers.
7.
7.
7.
7. Operation
Operation
Operation
Operation of
of
of
of Device
Device
Device
Device
7.1.1 Ask Coordinates
Apply for reply of longitude and latitude from device, the user can send SMS to SIM
number of device which will reply its last positioning coordinate automatically. A nd if
it has not fixed GPS ever, it will reply ” NO DATA ” .
SMS command: WHERE#
WHERE#
WHERE#
WHERE#
Example of reply:
Lat: N22.571285, Lon: E113.877115, Course: 42.20, Speed:0.0740, Date
Time:10-11-23 22:28:51
7.1.2 Ask Google Link
Apply for reply of Google link, it will reply Google link of last positioning longitude
and latitude. A nd if it has not fixed GPS ever, it will reply ” NO DATA ” .
SMS command: URL#
URL#
URL#
URL#
Example of reply:
<Date Time: 10-11-23 23:42:51>
http://maps.google.com/maps?q=N22.571490,E113.877103
If your mobile can get on internet, you can open the link in SMS, download map
picture with position of device via GPRS, WiFi or 3G etc. wireless searching method.
Also, you can view the location information in your computer by typing the link in
internet explore tool bar.
7.1.3 Via platform
Go to the platform website offered by dealers to check your vehicle location.
7.2 Vibration Alarm
When vehicle power is off, ACC status is also low, and if the lead time of low ACC is
more than 10 minutes
（
settable
）
, device will activate vibration alarm. When the
vibration alarm is on, once the vehicle vibrates for several times, the alarm will be
activated, in the later 3 minutes, vehicle power is still off
（
ACC is still OFF
）
,the
device will start vibration alarm , and then device will send alarm information and
exact longitude and latitude to platform, also to the SOS numbers preset.

e.g.: Sensor Alarm! “ about 84m near Gaoxinqi Campus of Bao ’ an Vocational
Technology School(Southeast ), Dabao Road, Bianjian Road, Bao ’ an Area, Shenzhen
City, Guangdong province, China ”
If the device can not get address for some reason, it will send a google link to the
SOS numbers as below:
<Date Time:11-06-17 14
：
53
：
06>
，
http://maps.google.com/maps?q=N22576713,E113.916585
Note: T o realize this function, please set special number beforehand
SMS “ SENSOR,0#
SENSOR,0#
SENSOR,0#
SENSOR,0# ” will turn off vibration alarm.
SMS ” ALM,OFF# ” will turn off vibration alarm via SMS, only alarm via
GPRS
SMS ” ALM,ON# ” will turn on get vibration alarm via SMS & GPRS.
7.3 Cut-off oil & power
W hen vehicle is stolen, the user can send command to cut off the oil & power via
monitoring platform, making sure vehicle is safely moving, cut off its oil & power
makes it can ’ t move anymore.
To cut off oil & power via platform this needs to logon with user name and password,
for the replied message, please check in SMS command list.
Note To make sure the security of vehicle, tracker can only indicate to cut off oil
when GPS is in valid position status, and the speed is less than 20KM/H or in static. It
needs password and platform account password is needed when sending oil cut off
command.
7.4 Restoring Oil
When the alarm is off, sending re storing oil commands manually. Device will restore
oil supplying, and vehicle will work normally again.
Platform account password is needed when sending oil cut off command.
To restore oil & power via platform this needs to logon with user name and password,
for the replied message, please check in SMS command list.
8.
8.
8.
8. Log
Log
Log
Log in
in
in
in GPS
GPS
GPS
GPS Platform
Platform
Platform
Platform
T he website is:
Please get instruction of Service Platform Operation from your dealer.
9.
9.
9.
9. Trouble
Trouble
Trouble
Trouble Shooting
Shooting
Shooting
Shooting
9.1 After installing it in the first time, if device can ’ t get connected with platform

server, at this time it is “ logged off ” status in platform.
Please check the installation of device:
1Check whether the connection of power-line is correct, please do not connect
it with the car control line.
2Check whether SIM card is installed correctly, please refer to the installation
manual;
3Whether ACC ignition cable is connected, please turn on the ACC with key
after it is connected.
4Check the LEDs ’ status. In normal working status, the red LED is in solid
bright or flashing; green LED and blue LED are both in solid bright.
5Check whether GPS is located, if not, please drive to the open areas for
positioning.
9.2 If it is “ offline ” status in platform:
First of all, check the three LEDs ’ status. If it is not convenient to check that
，
please
check the SIM card status :
1Check whether the vehicle is in no GSM area, such as basement;
2Check the GSM/GPS disconnection area, whether it is all disconnected or
few of them disconnected, to make sure whether it is the fault of operator ’ s
internet.
3Check whether your SIM card charge is overdue;
4Check whether the SIM card supports GPRS;
5Check the parameter setup, whether the device IMEI number, GPRS sending
interval is correct;
9.3 If the device ’ GPS function is normal, but can not locate for a long time, please
check whether the installation setup of device is correct:
1Please make sure the GPS antenna face is up;
2Please make sure there is no electromagnetic wave- absorbent object (metal)
above the device, especially the thermal-protective coating on the
windshield, it may affect the GPS reception of the device;
9.4 If GPS can ’ t receive the signals normally (there is high building around to
interfere with GPS reception), please drive to the open areas for positioning.
Generally, it needs 1-2 minutes to receive the first coordinates.
9.5 If GSM can ’ t receive the signals normally, please check whether SIM card is
installed correctly or there is no GSM signal at the location you are, such as basement
parking, please drive to a place covered by GSM signal reception.
9.6 When cell phone with special number receives tele-cutoff alarm SMS , please
make sure whether it is illegal wire cutoff, or the FUSE on power line is blown. If
the FUSE in it is blown, please contact your distributor to exchange with the same
model FUSE, after the internal trouble is shoot, it can be power on to work again.