SMC Networks 7908VOWBRB - annexe 2 User manual

After unpacking the SMC7908VoWBRB, check the contents of the
box to be sure you have received the following components:
•One BarricadeTM gADSL Wireless Broadband Voice Router
•One Power Adaptor
•One cable (RJ-11) for connection to the phone line
•One cable (RJ-45) for optional connection to a LAN device
•One CD-ROM containing full version of User Manual
•One Warranty Card
•One ADSL splitter *
* The ADSL splitter (also called microfilter) is only contained in packages related to specific
countries (US, UK, France, The Netherlands). If your package does not contain a splitter, you may
be required to purchase this item separately. Please contact your ISP for further details.
Please inform your dealer in the event of any incorrect, missing or
damaged parts. If possible, retain the carton and original packing
materials in case there is a need to return the product.
To install and connect to the SMC7908VoWBRB, you must have:
•An ADSL line installed by your ISP
•An ADSL splitter (at least one)
•A Computer with a CD-ROM drive
•Windows (98 or later), Mac (OS9 or later) or Linux
•An up to date web browser:
•Internet Explorer 5.5 or later
•Mozilla 1.7/Firefox 1.0 or later
Front
•Power (PWR) LED - When this green LED is on, the router is powered up.
•ADSL LED - This green LED flashes while a link is being set up on the ADSL port.
The LED stays on when the link has been set up and is functioning correctly.
•Online LED - This green LED will normally be off but flashes when data is sent or
received on the ADSL port.
•WLAN LED - When this green LED is on, wireless networking is enabled. The LED will
flash when data is sent or received over a wireless connection.
•LAN LEDs (LAN1, LAN2, LAN3 and LAN4) - These green LEDs turn on when there
is an Ethernet connection to the corresponding LAN port on the back panel and will
flash to indicate that data is being sent or received over the connection.
•Phone LED - Shows the VoIP FXS connection status. When the green LED is solid,
the Phone is OFF-Hook talking on a call. When the green LED is blinking, it indicates
there is an incoming VoIP Call. When the LED is off, the phone is ON-Hook.
•VoIP LED - Shows the VoIP status. When the green LED is solid, the VoIP link is up
and connected. When the green LED is blinking, the router is attempting to establish
a connection. When the LED is off, there is no connection.
•USB LED - Shows the USB status. When the green LED is solid, the USB is connected.
When the status is blinking green, the router is transmitting and receiving packets.
When the LED is off, there is no connection.
•PPP LED - The green LED will blink when a PPP connection is being negotiated and will
remain solid when a PPP connection is made and is functioning properly.
Back
1. ADSL Port - Use the supplied cable to connect the ADSL port to your phone socket.
The DSL LED on the front panel will light up when the connection is made and the
Online LED will turn when you are able to send and receive data.
2. LAN Ports (1, 2, 3 and 4) - There are four Ethernet LAN ports for connection to PCs,
network printers or similar devices. Note the labelling; one LAN LED on the front panel is
associated with one port on the rear panel. Port 1 is associated with the LAN1 LED, port 2
with LAN2 and so on. If a device is not correctly connected, using a suitable Ethernet
cable, the associated LED will not turn on.
3. Power - Connect the supplied, 12V power adapter to this socket.
4. Reset - You can restart the unit by pressing the reset button and releasing it
immediately. If, for any reason, you need to reset the unit to factory defaults and
cannot access the user interface (e.g. if you have changed and forgotten the
password), press the reset button for 10 seconds. Note that you will lose all your
configuration changes when you reset the router to factory defaults.
5. USB 1.1 Port - Use this port for connecting USB printer or storage device.
6. RJ-11 FXS Phone Ports - Use these ports to connect to a telephone.
Ethernet cables
Ethernet cables are usually constructed from unscreened, “Cat 5” cable with
RJ45 connecters at both ends. Cables of this type can be purchased at most
computer retailers.
Installation Troubleshooting
•Check that the Power Adapter is both plugged into a working power socket and
connected to the Router. Check that the green PWR LED on the Router is on.
Only use the power adapter that was supplied with your Router.
• The wired PC should connect to a LAN port of the Router using an Ethernet
cable. The corresponding LAN LED of the Router should be on.
• The Router ADSL port should be connected to your phone socket on the wall. The DSL
LED should be on when there is a valid connection to your ISP. The Online LED will
flash when data is transferred to and from the ADSL port.
• Power up your equipment in the following order: First the ADSL Router and then
your PC. Leave at least 30 seconds between turning on each device.
• The PC should be setup to obtain an IP address automatically from the Router's
DHCP server. See the user manual on the CD for details of how to setup your PC
to obtain an IP address.
• Check that web proxy is disabled on your PC. Go to the Control Paneland select
Internet Options. Select the Connections tab and click the LAN Settings button.
Check that the Use Proxy Serveroption is not ticked.
• Check you can access the Router's web interface. Open a browser and enter
http://192.168.2.1 to access the default IP address of the Router.
WAN Connection Troubleshooting
• Check that you have selected the correct WAN connection option and the ISP
details are correct. If you do not have these details, they can be obtained from
your ISP.
• If you have any PPPoE client applications already installed on your PC which
were required when your PC was directly connected to the DSL modem, they
must be disabled.
Wireless Troubleshooting
• Check that the SSID is the same on the Router and the wireless PC.
• Check that the wireless encryption is the same on the Router and the wireless
PC. To help debug a problem, turn off encryption in both the Router and wireless
PC until you can establish a connection. After a change in encryption, some PCs
may have to be restarted.
• The wireless PCs must be set to Infrastructure mode to work with a Router.
• If your computer has both a wired and wireless connection installed, ensure that
the wired Ethernet cable is unplugged.
• Check that the Router WLAN LED is on, to indicate that Wireless networking is
enabled. To enable wireless networking, go to the Router Wireless page and
enable Wireless Networking.
• If there are a number of wireless networks within range, then you may
experience poor wireless performance if the wireless channels are too close
together. Ideally, neighbouring wireless networks should be at least 5
channels apart. The wireless channel is controlled by and set in the Router.
• The Router has a feature called MAC Filter which controls which wireless PCs
have access to the wireless LAN. If this feature is enabled, then ensure that the MAC
address of your wireless PC card is listed in the MAC Filter page.
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and
reliable. However, no responsibility is assumed by SMC for its use, nor for any infringe-
ments of patents or other rights of third parties, which may result from its use. No
license is granted by implication or otherwise under any patent or patent rights of
SMC. SMC reserves the right to change specifications at any time without notice.
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618
Copyright © SMC Networks, Inc., 2005. All rights reserved. SMC is a
registered trademark; and BarricadeTM is a trademark of SMC Networks, Inc.
Other product and company names are trademarks or registered
trademarks of their respective holders.
FOR TECHNICAL SUPPORT, CALL:
From U.S.A. and Canada
(24 hours a day, 7 days a week)
(800) SMC-4-YOU
Phn: [phone]
Fax: [phone]
From Europe : Contact details can be
found on www.smc.com
INTERNET
E-mail addresses:
t[email protected]
Driver updates:
http://www.smc.com/index.cfm?action=
techsupport drivers downloads
World Wide Web:
http://www.smc.com/
If you are looking for further contact
information, please visit www.smc.com
38 Tesla
Irvine, CA 92618
Phone: [phone]
Model Number: SMC7908VoWBRB
Package Contents
Package Contents
System Requirements
System Requirements
Hardware Description
Hardware Description Troubleshooting
Troubleshooting
7908VoWBRB_qig.qxp 14/04/05 16:33 Page 1

Thank you for choosing the SMC BarricadeTM ADSL Wireless Broadband Voice
Router. This Quick Installation Guide will enable you to have your new router
up and running in a few minutes. Please complete each stage of these easy to
follow instructions.
The position of your Router is important to its wireless performance. The
Router should be located in a central position relative to the wireless PCs that will
connect to it. A suitable location might be on a high shelf or a similar
position that allows good wireless coverage from the Router to the wireless PCs.
To meet the FCC wireless radiation exposure regulations, the Router should
be located in a position to maintain a minimum distance of 20cm (8 inches)
from any personnel.
Connect all of the computers that you want to share
on your internet connection to your router. During
the initial setup, SMC recommend that the Router is
configured from a wired Ethernet PC as shown in the
diagram.
To keep the high-frequency ADSL signals from
interfering with telephone calls, each phone must
be connected to the phone-line through a
splitter (also known as and ADSL microfilter).
The ADSL connection of the router does not
require to be filtered as the frequencies
produced by telephones do not interfere
with the ADSL connection.
Get Connected
Applications
Wireless Networking
Package Contents
Troubleshooting
Configuration
System Requirements
Hardware Description
Disable HTTP Proxy
Netscape
Explorer
Configuring your Macintosh
Configure TCP/IP Settings
Configure the Barricade g
Netscape
ExplorerExplorer
Configuring your Macintosh
Windows 98SE/ME
Windows 2000/XP
Configure TCP/IP Settings
Configure the Barricade g
Quick Installation Guide
ADSL2 Barricade™ Broadband VoIP Router
with Built-in Annex A ADSL2/2+Modem
SMC7908VoWBRA
HarHardwdwarare Inse InstallationallationHardware Installation
EZ Installation CD
Initial Configuration
5. The first page of the Setup Wizard (Getting Started) provides back-
ground information. Click on the NEXT button after you have read the
page and taken any action required.
6. The Wireless Settings page allows you to change the behaviour of the
wireless. If you are unfamiliar with the terminology, do not change the
values; they can always be changed later if required. See the Wireless
Networking Section for more information.
7. The next page allows you to configure your time-zone. Select the
appropriate time-zone from the drop-down list then select the Primary
Server and Secondary Server that are closest to your location. Click on
the NEXT button when you are happy with your choices.
8. The next page of the wizard configures your ADSL connection.
a. First select your country from the drop-down list. If your country does
not appear on the list then select Other.
b. If your country was on the list you will now be able to select an
Internet/Network Provider from the drop-down list. If your provider
does not appear on the list, select Other. Note that your servic
provider may have changed their connection parameters from those
used by the router. If you are in any doubt, please check with your ISP
and select Other to enter the parameters manually.
c. If you selected Other for your country or Service/Network Provider,
you will now have to manually select the protocol your provider uses.
Fill in the blank fields with the information provided by your Internet/
Network Provider. Click on NEXT when you have entered the information.
9. The final page of the wizard shows a summary of all the information that
you have entered. Click on FINISH to confirm your choices and connect to
the Internet or click on BACK to return to a page to make further changes.
That's it! When you click on FINISH, you should be connected to the Internet.
Please register your product by pointing your Web browser to www.smc.com
and clicking through to the support pages.
If you are not connected to the Internet, please contact your ISP to clarify
your connection details.
To setup Wireless networking you must select the Wireless option in the
Advanced Setup section.
1. To create a wireless network, the Router and wireless PCs must have the
same SSID and encryption settings. The default wireless settings for the
Router are shown below:
•SSID - Router default is SMC The SSID is the name given to your wireless
LAN. Only PCs with the same SSID as the Router can connect to the
wireless LAN.
•Wireless Encryption - Router default is off To set up your wireless network,
set the encryption to off in both the Router and the wireless PC. Wireless
encryption can be set up later, after you have established a wireless network.
•Wireless Channel - Router default is Auto The Router will automatically
select a clear wireless channel. If there are no other wireless networks in
the area, the Router will default to channel 6. The wireless PCs will
Follow the steps in this section after you have connected your hardware as
described in the Hardware Installation section. Before beginning, make sure
you have all the details about your internet connection from your ISP.
Note: On first power-up or immediately following a Restore to Factory
Defaults, the wireless is turned off. Initial configuration must be performed
using a wired connection.
1. First, power-up your router then power-up the PC that you will use to
configure the router.
2. Start your web browser and enter the address http://192.168.2.1. If your
PC is properly configured you will see the login page of the router. If you
cannot access the login page then you must first reconfigure your PC to
obtain an IP address automatically; see the manual on the CD-ROM for
more information.
3. Type in the password (the default is smcadmin) and click on Login. When
you have successfully logged in, you will see the Country Selection page.
Your choice of country will be used to configure the wireless so it is
important that you make the correct selection from the drop down list.
Once you have made your selection click on the Apply button to go to the
Home page.
Note: The Country Selection page only appears on first power-up or
immediately following a Restore to Factory Defaults.
4. The Home page allows you to choose between the Setup Wizard and
Advanced Setup. Select Setup Wizard.
WIRELESS
VoI P ADSL
ROUTER
INTEGRATED
FIREWALL
10/100 Mbps
CLIENTS
54 Mbps
CLIENTS
11 Mbps
CLIENTS
INTERNET
automatically scan the channels to detect which channel the
Router is using.
If this is your only wireless network, then you can use the Router's default
settings. Now set your wireless PC to have the same SSID and encryption
settings as the Router. The wireless PCs must also be set to use
infrastructure mode.
2. If your computer has both a wired and wireless connection installed, then
you must ensure that only one type is used at a time, to connect to the
LAN. To use the wireless connection, unplug the wired Ethernet cable and
reboot the PC.
3. Once you have setup the same SSID and Encryption in the Router and
wireless PC, open a browser and try to connect to www.smc.com. If you
can access the internet, then you have successfully set up your wireless
LAN.
4. SMC recommends that you enable wireless encryption to improve the
security of your wireless network. Note that if you change the wireless
settings (e.g. SSID or WEP) of your Router from a wireless PC, then you
may lose contact with your Router. To re-establish the wireless connection,
change the wireless settings of your PC to be the same as the Router.
Hardware Installation
Hardware Installation
Wireless Networking
Wireless Networking
Initial Configuration
Initial Configuration
ADSL BarricadeTM gBroadband Voice Router
with Built-in Annex B ADSL2/2+Modem
ADSL BarricadeTM gBroadband Voice Router
with Built-in Annex B ADSL2/2+Modem
Quick Installation Guide
Quick Installation Guide
SMC7908VoWBRB
SMC7908VoWBRB
7908VoWBRB_qig.qxp 14/04/05 16:33 Page 2