Smith & Noble Euro Track Basics Hardware-Heavy Duty User manual

STEP BY STEP INSTALLATION INSTRUCTIONS
Wall Mount
Single Rod Set
Euro Track
Basics Hardware -
Heavy Duty

2
800.248.8888
1smithandnoble.com
A Smooth Set-Up
We want you to love your new hardware and that includes
having a smooth installation experience. We suggest saving
        
please reach out to us for help. It’s why we’re here. Call us at
800.248.8888 for more info on installation.
We recommend you hold on to all packaging until your
hardware is fully installed. Should something go wrong (we
          
painless as possible.
Customer Service Hours
Monday — Friday: 6am — 6pm PT
Saturday — Sunday: 7am — 4pm PT
smithandnoble.com
Everything
You Need
Table of Contents
Step 1 -  GengStarted ........................................3
Overview -WallMountSingleRodSet ...........................4
Step 2 -  MounngtheBrackets ..............................5 - 6
Step 3 -AachingtheRodConnector............................7
Step 4 - AddingorRemovingCarriers&EndStops.................8
Step 5 - AachingBracketPoststoRod ..........................9
Step 6 -AachingFinials ......................................10
Step 7 -AachingBracketPoststoBracketBases ................11
Step 8 -AachingDraperytoRod ..............................12
Accessories -Baton/Wand ....................................13
Care&Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BackCover

34
smithandnoble.com 800.248.8888
STEP 1 - GETTING STARTED OVERVIEW
Heavy Duty Wall Mount Single Rod Set
sure you have all the parts you need.
You’ll need to make sure the surface you intend to install your hardware is sturdy enough to
accommodate the brackets. If you’re screwing directly into a surface this means locating wood
studs that are strong enough to securely bond with the
        
fastener (as illustrated) but please note this piece is not
included.
WALLBOARD OR PLASTER: Hollow wall applications: Use a secure fastener designed

METAL: Prepare by pre-drilling holes and then using the included screws.
CONCRETE, STONE, BRICK OR TILE:
screws.When selecting a fastener be sure it’s designed to support the weight of the product being


TOOLS YOU WILL NEED TO INSTALL YOUR HARDWARE:  ¼

764
"drill bit.
Note: It’s important to monitor the amount of pressure you apply when using a drill. If the screws
are too tight this may cause the screw itself to break off in the wall or window frame.
Parts & Tools
MOLLY
BOLT
SELF DRILLING
ANCHOR
TOGGLE
BOLT
SCREWS SPLICE CLIP MOUNTING BRACKET
ROD CONNECTOR
(OPTIONAL) CARRIERS
CENTER SPLICE BRACKET
SCREWDRIVER & PENCIL
(NOT INCLUDED)
POWER DRILL
(NOT INCLUDED)
LEVEL
(NOT INCLUDED)
ROD QTY BRACKET QTY ROD WIDTH
1 2 24"— 60"
1 3 8"—96"
2 5 8"—168"
2 7 8"—192"
3 7 8"—264"
3 9 8"—276"
310 8"—288"
411 8"—360"
413 8"—384"
FINIAL
(OPTIONAL)
MASTER
CARRIER CARRIERS
FINIAL
MOUNTING
BRACKET
OUTSIDE
POST
INSIDE
POST
MOUNTING
PLATE
COVER
PLATE
HEX
BOLT
HEX
BOLT

56
smithandnoble.com 800.248.8888
STEP 2 - MOUNTING BRACKETS STEP 2 - MOUNTING BRACKETS
Place the panel on the rod. To ensure
      
it up to the spot you wish to install
it; this will allow you to raise or lower
your treatment as desired. After

a pencil to mark the wall where the
top of the rod is resting.
Remove the panel from the rod and
then center the rod over the window
opening at the desired height. Using
      
each rod are positioned;if you’re using
     
point between these two spots. If you
have more than one center bracket
spread these evenly between the two
end brackets and center point. If you
      
splice is on the wall since you will
need to add the special splice bracket
at that point. Measure 6” inward from
the marks you’ve made on both ends
and mark those spots. This is where
the end brackets will be installed.
CENTER ROD 6"
OUTSIDE
POST
INSIDE
POST
MOUNTING
PLATE
COVER
PLATE
HEX
BOLT
END & CENTER BRACKETS
CENTER SPLICE BRACKET
FIGURE B
Mark all holes needed
showing locations of screw
holes for all brackets.
BACK PLATE
OUTSIDE
POST
INSIDE
POST
MOUNTING
PLATE
COVER
PLATE
HEX
BOLT
HEX
BOLT
Place center of bracket cover plate
level against wall at the marked spots.
      
around the base of the bracket onto
 (see Figure A). Check to make
sure the circles are level & aligned
with each other.
Remove back plate and center it
inside of the circle outline on wall.
Mark the screw hole locations for all
brackets (see Figure B).
Attach the metal back plate to the

with the marks made in the previous
step (see Figure B). Be sure and
attach the plate to the wall with the
appropriate mounting hardware.
(It is always recommended to try
and attach to the wood studs inside
the wall. Where this is not possible
please use a wall anchor suitable to
carry the weight of your hardware
selection as well as your draperies
and any accessories.)
Place bracket cover plate on top of
back plate and thread on the inside
post. Make sure to screw on the post
very tightly. Do not leave any play or
wiggle room. Put the outside post to
the side since you will use it later.
FIGURE A

78
smithandnoble.com 800.248.8888
STEP 3 - ATTACHING THE ROD CONNECTOR STEP 4 - ADDING/REMOVING CARRIERS & END STOPS
     
have received a rod connector.
A rod connector is the short piece of
metal placed inside each end of the
rods in a multi-segment system to
join them together.
Join track sections together and
fasten securely with set screws.
Attach mounting/splice clip at splice
by pressing clip down and snapping
it to track.
Adding or Removing
Carriers to the Rod
Your track rod will come with all
master carriers and regular carriers
pre-installed.
If you need to add or take out some

unscrew the End Cap from the rod.
Remove the carrier & end stop and either
add or take out the carriers needed.
CARRIERS
ROD
SPLICER
ROD CONNECTOR
END
STOP
FINIAL
END CAP
ROD
END STOP
ROD
SPLICE
MOUNTING/SPLICE
CLIP
REMOVE OR ADD
CARRIERS HERE

910
smithandnoble.com 800.248.8888
Slide in End Cap onto rod and
tighten screw.
STEP 6 - ATTACHING FINIALS
UPGRADED
END CAP FINIALS
STANDARD
END CAP FINIALS
(OPTIONAL)
BACK
OF ROD
BACK
OF ROD
BACK
OF ROD
BACK
OF ROD
STEP 5 - ATTACHING BRACKETS POSTS TO ROD
Attach Bracket Posts to
Rod (Track)
Loosen Hex screw on Outside
Mounting posts.
Insert the Hex screw into the
channel in the back of the track.
Do not tighten at this time.
Attach End Cap Finial.
(go to step 6)
BACK
CHANNEL
CHANNEL
OUTSIDE
MOUNTING
POST
HEX
SCREW

11 12
smithandnoble.com 800.248.8888
STEP 7 - ATTACHING BRACKET POSTS TO BRACKET BASES STEP 8 - ATTACHING DRAPERY TO ROD
Align outside posts with Inside Posts.
(Fig. A)
Slide Outside Posts over Inside Posts.
    

posts securely by turning clockwise.
(Fig. B)
Tighten set screws. (Fig. C) OUTSIDE
POST
TRACK
SET
SCREW
INSIDE
POST
Insert drapery pin hooks into carriers
and master carriers.
Split Drapery

the center and go towards the ends.
One-Way Draw Drapery
For drapery opening from one side

side towards the end.
SPLIT DRAPERY
BACK VIEW OF ROD
BACK VIEW OF ROD
ONE-WAY DRAW DRAPERY
MASTER
CARRIER
MASTER
CARRIER
WAND
WAND
ROD
ROD
DRAPERY PIN
DRAPERY
PIN
Tighten set screws
Tighten mounting
posts on track by
turning clockwise
FIGURE A
FIGURE B
FIGURE C

13 14
smithandnoble.com 800.248.8888
Minimal care and cleaning is needed to maintain the beauty of your Hardware.
To Vacuum: Use brush or dust head attachment.

CARE & CLEANINGACCESSORIES
Baton/Wand (optional)
Baton/Wand will be pre-attached to
the master carrier(s).
CLIP
BATON/
WAND

© 2021 Smith & Noble Home, Inc. All Rights Reserved SN062021
Warranty Service
           
products come with a limited lifetime warranty. The warranty applies to the
            
covers defects in material or craftsmanship. Hardware must have been properly
installed. We reserve the right to determine if your hardware warrants a repair
or a replacement. Visit smithandnoble.com/guarantee to see full details. In
need of warranty service? Call us at 800.248.8888 and we’ll arrange for a repair
or replacement ASAP.